1995 LAND ROVER DISCOVERY oil capacities

LUBRICANTS, FLUIDS AND CAPACITIES
1
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS -
USA VEHICLES
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Engine Use oils to API 5W/20 )
service level
SGSH 5W/30 )
or 5W/40 )
RES.22.OL.G4
or
CCMC G4 10W/30
10W/40 )
10W/50 )
15W/40 )
15W/50 )
20W/40 )
20W/50 )
Automatic gearbox ATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B, C
or D 80W EP
Power steering ATF Dexron IID
LT 230T API GL4 or GL5
transfer gearbox MIL - L - 2105 or
MIL - L - 2105B
Brake reservoir Brake fluid must have a minimum
boiling point of 260°C (500ÊF) and
comply with FMVSS/116/DOT 4
Lubrication nipples
(hubs, ball joints,
etc.)NLGI-2 multipurpose lithium based
grease
See table on page 3 for remaining vehicle components

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS
All climates and conditions
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Petrol modelsOils must meet: 5W/30
Engine sump
RES.22.OL.G-4 5W/40
or 5W/50
CCMC G-4 or 10W/30
API SG or SH 10W/40
10W/50
15W/40
15W/50
20W/40
20W/50
25W/40
25W/50
DieselRES.22.OL.PD-2 15W/40
Engine sump or CCMC PD-2
or API CD
Main Gearbox
AutomaticATF Dexron IID
Main Gearbox
manualATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD
Power steering ATF Dexron IID
Transfer box API GL4 or GL5 90 EP
LT230T MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant Use an ethylene glycol based anti-freeze (containing no methanol)
V8i, Tdi, Mpi with non-phosphate corrosion inhibitors suitable for use in aluminium engines to ensure
the protection of the cooling system against frost and corrosion in all seasons. Use one
part anti-freeze to one part water for protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below proportions one part
anti-freeze to three parts water, i.e. minimum 25% anti-freeze in coolant otherwise
damage to engine is liable to occur. Or a maximum of 60%.
Battery lugs, Petroleum jelly.
Earthing surfacesNOTE: Do not use Silicone Grease
where paint has
been removed
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil Nippon Denso ND-oil8 Unipart ND-oil8
ABS Sensor Silicone grease: Staborags NBU - Wabco 830 502,0634
bush-rear Wacker chemie 704 - Wabco 830 502,0164
Kluber GL301
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze windscreen washer additives, lubricants and various adhesives.

09LUBRICANTS, FLUIDS AND CAPACITIES
4
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Imp.Unit US unit
Engine sump oil
- 300Tdi models 5,8...................................................... 10.20 pt 12.30 pt
- V8i petrol models 3.9 6,1............................................ 10.70 pt 12.90 pt
- Mpi petrol models 4,90.................................................. 8.70 pt 10.40 pt
Extra when refilling after fitting new filter
- 300Tdi models 0,85...................................................... 1.50 pt 1.80 pt
- V8i petrol models 0,56.................................................. 1.00 pt 1.20 pt
- Mpi 0,4........................................................................ 0.70 pt 0.85 pt
Manual gearbox 2,67............................................................... 4.70 pt 5.70 pt
Automatic gearbox 9,1........................................................... 16.00 pt 19.20 pt
Transfer gearbox oil 2,30......................................................... 4.00 pt 4.90 pt
Front differential 1,70............................................................... 3.00 pt 3.60 pt
Rear differential 1,70................................................................ 3.00 pt 3.60 pt
Power steering box and reservoir LHD 2,90............................ 5.00 pt 6.00 pt
Power steering box and reservoir RHD 3,40............................ 6.00 pt 7.20 pt
Swivel pin housing oil (each) 0,35............................................ 0.60 pt 0.75 pt
Fuel tank usable fuel 89,0........................................................ 19.5 gall 23 gall
Cooling system
- 300Tdi models 11,50...................................................... 20.20 pt 24.30 pt
- V8i petrol models 11,30.................................................. 20.00 pt 23.90 pt
- Mpi 10,00........................................................................ 17.60 pt 21.00 pt
Washer bottle 7,0................................................................... 12.30 pt 14.80 pt
NOTE: * All levels must be checked by dipstick or level plugs as applicable. When draining oil
from the ZF automatic gearbox, oil will remain in the torque converter, refill to high level on
dipstick only.

LUBRICANTS, FLUIDS AND CAPACITIES
5
INFORMATION ANTI-FREEZE
ENGINE TYPE MIXTURE STRENGTH PERCENTAGE PROTECTION
CONCENTRATION LOWER
TEMPERATURE
LIMIT
V8i Engine One part anti-freeze
Diesel Engine One part water 50%
Complete protection-33°F
Vehicle may be driven away immediately from cold - 36°C
Safe limit protection-41°C
Coolant in mushy state. Engine may be started and driven away after warm-up
period-42°F
Lower protection-47°C
Prevents frost damage to cylinder head, block and radiator. Thaw out before
starting engine-53°F
CAUTION: Anti-freeze content must never be allowed to fall below 25% otherwise damage to the
engine is liable to occur. Also, anti-freeze content should not exceed 60% as this will greatly
reduce the cooling effect of the coolant.
FUEL REQUIREMENTS
Catalyst vehicles
Vehicles equipped with catalytic converter are designed to use ONLY unleaded fuel. Unleaded fuel must be used
for the emission control system to operate properly. Its use will also reduce spark plug fouling, exhaust system
corrosion and engine oil deterioration.
Using fuel that contains lead will result in damage to the emission control system and could result in loss of
warranty coverage. The effectiveness of the catalysts in the catalytic converters will be seriously impaired if leaded
fuel is used. The vehicle is equipped with an electronic fuel injection system, which includes two oxygen sensors.
Leaded fuel will damage the sensors, and will deteriorate the emission control system.
Regulations require that pumps delivering unleaded fuel be labelledUNLEADED.Only these pumps have nozzles
which fit the filler neck of the vehicle fuel tank.

09LUBRICANTS, FLUIDS AND CAPACITIES
6
INFORMATION RECOMMENDED FUEL
Petrol engines
- with catalytic converter unleaded only, 95 RON (USA 90 CLC or AKI)................................................
- non catalytic, 9.35:1 compression ratio leaded 97 RON/unleaded 95 RON.......................
- non catalytic, 8.13:1 compression ratio leaded 90 RON/unleaded 95 RON.......................
- Australia minimum 91 RON unleaded......................................................................
Diesel engines
300Tdi Diesel fuel oil,distillate,diesel fuel, automotive gas or...........................................................................
Derv to British standard 2869, Class A1 or A2
Using fuel with an octane rating lower than stated above could seriously impair vehicle performance.
CAUTION: Do not use oxygenated fuels such as blends of methanol/ gasoline or ethanol/gasoline
(e.g. 'Gasohol'). Take care not to spill fuel during refuelling.

MAINTENANCE
13
MAINTENANCE
RENEW AUTOMATIC GEARBOX FLUID AND OIL
SCREEN
1.Site vehicle on lift or level ground. Place
container to drain gearbox fluid into. Disconnect
battery negative lead.
2.Remove gearbox dipstick, located at rear of right
hand rocker cover, to aid oil drainage. Release
plug from bottom of sump and allow fluid to drain
completely.
3.Refit plug using a new sealing washer. Tighten
to
10 Nm
Refill ZF Automatic Gearbox and Check Fluid
Level.
NOTE: The fluid level must checked when
fluid is cold and engine idling in park.
4.Ensure vehicle is on level ground.
5.Refill or top-up with correct quantity and grade of
fluid.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
6.Start and run engine. Apply footbrake, select
position 1 then back to park. Check fluid level,
this must be between the two marks on the
dipstick.
Oil screen replacement ZF automatic gearbox.
See AUTOMATIC GEARBOX, Repair, Oil Screen

Tdi
13
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Disconnect battery negative lead.
2.Drain engine oil.
3.Slacken sump securing bolts and, using a sharp
knife, break sealant around sump flange.
4.Remove bolts and withdraw sump.
Refit
5.Clean mating faces of sump, timing gear housing
and cylinder block.
6.Apply a 2,0 mm bead of 'Hylosil RTV102' to the
sump flange, ensuring bead is applied inboard of
the bolt holes.
7.Secure sump to block with bolts. Tighten to
25
Nm.
8.Refill engine oil.See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
9.Reconnect battery negative lead.OIL PICK-UP STRAINER
Service repair no - 12.60.20
Remove
1.Disconnect battery negative lead.
2.Drain engine oil.
3.Remove engine oil sump.
See Oil Sump
4.Remove bolts securing pipe support bracket.
5.Remove bolts from pipe flanges.
6.Withdraw pick-up strainer assembly.
Refit
7.Refit pick-up strainer assembly, fitting a new 'O'
ring seal at oil pump connection.
8.Apply Loctite 242E to the two screws at the
bearing cap. Tighten to
9 Nm.
9.Fit bolts to pipe flanges. Tighten to25 Nm.
10.Refit engine oil sump.See Oil Sump
11.Reconnect battery negative lead.