1994 MAZDA MX-5 belt

s INDEX 1. Power window system ............. Structural view page S-19 ............ Troubleshooting page S-20 ................. Inspection page S-22 2. Fuel-filler lid opener ....... Removal / Installation page $23 3. Dashboard and console ....... Removal / Installation page S-56 ................. Adjustment page S-58 4. Trim ....... Removal / Installation page S-59 5. Floor covering ....... Removal / Installation page S-62 6. Seat belt ....... Removal / Installation page $63 ................. Inspection page S-64 7. Seat ....... Removal 1 Installation page S-65 Disassembly / Assembly .... page S-66 'd' ................. Inspection page S-65 8. Brace bar Removal / Installation ....... page S-84 Gartner Banana

WINDOW REGULATOR, GLASS, AND GUIDE S WINDOW REGULATOR, GLASS, AND GUIDE COMPONENTS Removal / Installation 1. Raise the door glass about 190 mm (7.5 in) from the fully open position. 2. Disconnect the negative battery cable. Note Remove the door screen carefully so that it may be reused. 3. Remove in the order shown in the figure, referring to Removal Note. 4. Install in the reverse order of removal, referring to lnstallation Note. 1. Regulator handle Removal Note . . Installation Note 2. lnner handle cover 3. Pull handle 4. Door trim Removal Note . . 5. lnner handle 6. Sealing pad 7. Door screen 8. Upper glass stopper 9. page S-10 ........... page S-10 ........... 10. 12. page S-61 ........... 13. Front beltline molding Removal Note ............. page S-28 Door glass Adjustment ................ page S-10 Window regulator Glass guide Door weatherstrip Division channel Quarter glass weatherstrip Quarter glass Speaker (if necessary) Dovetail (if necessary) Gartner Banana

MOLDING AND GARNISH s MOLDING AND GARNISH COMPONENTS Removal / Installation 1. Remove in the order shown in the figure, referring to Removal Note. 2. Install in the reverse order of removal. 1 REPLACE P REPLACE 1. Windshield molding 4. Beltline molding ............. Installation Note ........... page S-28 Removal Note page S-28 2. Cowl grille 5. Rear window molding (detachable hardtop) ....... ........... Removal I Installation page S-44 Installation Note page S-29 3. Front beltline molding 6. Rear finisher ............. Removal Note ............. page S-28 Removal Note page $28 Gartner Banana

s MOLDING AND GARNISH Removal Note Front beltline molding Remove the outside mirror to remove the front beltline molding. (Refer to page S-34.) i/ Rear finisher Remove the rear combination light to remove the rear finisher. (Refer to Section T.) PRIMER 45UOSX42C I MOLDING I MOLDING Beltline molding Remove the convertible top to remove the beltline mold- ing. (Refer to page S-67.) Installation Note Windshield molding 1. Remove the windshield. (Refer to page S-44.) 2. Install the windshield. (Refer to page S-44.) 3. Apply primer with a brush to the bonding area of the new upper molding. Keep the bonding area free of dirt and -- grease, and do not touch the surface. Allow the primer to dry for approximately 30 minutes. 4. Align the center mark in the molding with the glass mark (0) 5. Install the upper portions of the molding into the body (Q) . 6. Push the corner of the molding into the body ((3). 7. Push the side portions of the molding into the body, beginning from the bottom (@). 8. Check for water leaks. If a leak is found, wipe the water off well and repeat the installation. Hardening time of repair sealant Time required until car Temperature Surface hardening time ,, be put into service 5°C (41 OF) Aoorox. 1.5 hr 12 hr I 35°C {95"F} I Approx. 10 rnin 2 hr 1 Gartner Banana

REAR WINDOW REAR WINDOW (CONVERTIBLE TOP) COMPONENTS Removal / Installation 1. Remove in the order shown in the figure, referring to Removal Note. 2. Install in the reverse order of removal, referring to Installation Note. 1. Rear package trim 2. Set plate 3. Beltline cover 4. Beltline protector 5. Rain rail 6. Zipper stop 7. Rear window e Removal Note . . . . . . . . . . . . . page S-53 Installation Note . . . . . . . . . . . page S-54 Gartner Banana

REAR WINDOW s PUL PROTECTOR Removal Note Rear window 1. Remove the rear package trim. 2. Remove the set plates. 3. Unzip th fully. e rear window, and lower the convertible top 4. Remove the beltline covers. 5. Remove the beltline protectors. 6. Remove the rain rail mounting fasteners from the body. 7. Leave the top latch assemblies in the unlocked position. Raise the convertible top completely. 8. Remove the rain rail from the studs. 9. Remove the rivets from the link assembly with a drill. Drill size: @4.0mm ($0.16 in) 10. Remove the rain rail from the body. Gartner Banana

REAR WINDOW s OUTER RAIN RAIL 9 , BELTLINE COVER PROTECTOR 5. lnstall the zipper stops to the rear window and the top fabric. 6. Affix the rear window to the top fabric with the Velcro. 7. Mount the outer rain rail to the studs. 8. Mount the top fabric to the studs. 9. Mount the rear window to the studs. 10. Mount the inner rain rail to the studs. 11. Loosely install the set plates beginning at the left side. 12. Unzip the rear window, and lower the convertible top fully. 13. lnstall the rain rail with the fasteners. 14. lnstall the beltline protectors. 15. lnstall the beltline cover. 16. Raise the convertible top completely, and lock the top latch assemblies. 17. Zip the rear window into place. 18. Tighten the set plate mounting nuts. Tightening torque: 8.Q-11.7 N.m (90-1 20 kgfem, 79-1 04 ft-lbf) 19. Rivet the top fabric to the link assembly. 20. lnstall the rear package trim. 21. If there is any sagging of the top fabric, remove the pull tab and realign the zipper. Gartner Banana

FLOOR COVERING FLOOR COVERING COMPONENTS Removal / Installation 1. To remove the cabin carpet, first remove the following: a Seats (Refer to page S-65.) b Dashboard (Refer to page S-56.) c Heater unit (Refer to Section U) d Front side trim, scuff plates, quarter trim, and rear package trim (Refer to page S-59.) e Front seat belts and buckles (Refer to page S-63.) 2. Remove the remaining parts in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear end mat 2. Foot rest 3. Bracket 4. Cabin carpet Gartner Banana