Page 759 of 1708

Before beginning any service procedure. refer to section T of this manual for air bag system service warnings and audio antitheft system alarm conditions . BODY INDEX ............................. S- 2 HOOD ............................. S- 5 COMPONENTS ................... S- 5 DOOR ............................. S- 7 COMPONENTS ................... S- 7 WINDOW REGULATOR. GLASS. AND GUIDE ....................... S- 9 COMPONENTS ................... S- 9 ......... DOOR LOCK AND OPENER S-15 ................... COMPONENTS S-15 TRUNK LID ........................ S-16 COMPONENTS ................... S-16 .... TRUNK LID LOCK AND OPENER S-18 COMPONENTS ................... S-18 ......... POWER WINDOW SYSTEM S-19 .............. STRUCTURAL VIEW S-19 TROUBLESHOOTING ............. S-20 ........ b POWER WINDOW SWITCH S-22 ... POWER WINDOW REGULATOR S-22 ......... FUEL-FILLER LID OPENER S-23 COMPONENTS ................... S-23 FRONT BUMPER ................... S-24 COMPONENTS ................... S-24 REAR BUMPER .................... S-25 COMPONENTS ................... S-25 ........... MOLDING AND GARNISH S-27 COMPONENTS ................... S-27 OUTSIDE MIRROR ................. S-30 STRUCTURAL VIEW .............. S-30 ............. TROUBLESHOOTING S-31 POWER OUTSIDE MIRROR ....... S-33 POWER OUTSIDE MIRROR SWITCH ........................ S-33 COMPONENTS ................... S-34 WINDSHIELD WIPER AND WASHER . S-35 TROUBLESHOOTING ............. S-35 WIPER MOTOR .................. S-38 ................ WASHER MOTOR S-38 FRONT WIPER AND WASHER ........................ SWITCH S-38 ................... COMPONENTS S39 WINDSHIELD ...................... S-44 PREPARATION ................... S-44 ................... COMPONENTS S-44 REAR WINDOW GLASS ......... (DETACHABLE HARDTOP) S-48 PREPARATION ................... S48 ................... COMPONENTS S48 REAR WINDOW .............. (CONVERTIBLE TOP) S-52 ................... COMPONENTS S-52 ....... DASHBOARD AND CONSOLE S-56 ................... COMPONENTS S56 TRIM .............................. S-59 COMPONENTS ................... S-59 ................. FLOOR COVERING S-62 ................... COMPONENTS -21 SEAT BELT ........................ S-63 COMPONENTS ................... S-63 ...................... SEAT BELT S-64 ................ BUCKLE SWITCH S-64 SEAT .............................. S-65 ................... COMPONENTS S-65 ................ CONVERTIBLE TOP S-67 PREPARATION ................... S-67 ................... COMPONENTS S-67 ........... DETACHABLE HARDTOP S-81 COMPONENTS ................... S-81 BRACE BAR ....................... S-84 ................... COMPONENTS S-84 ......... UNDERBODY DIMENSIONS S-85 PROJECTED DIMENSIONS ........ S-85 ..... STRAIGHT-LINE DIMENSIONS S-87 45uoSx-001 Gartner Banana
Page 762 of 1708
s INDEX 1. Power window system ............. Structural view page S-19 ............ Troubleshooting page S-20 ................. Inspection page S-22 2. Fuel-filler lid opener ....... Removal / Installation page $23 3. Dashboard and console ....... Removal / Installation page S-56 ................. Adjustment page S-58 4. Trim ....... Removal / Installation page S-59 5. Floor covering ....... Removal / Installation page S-62 6. Seat belt ....... Removal / Installation page $63 ................. Inspection page S-64 7. Seat ....... Removal 1 Installation page S-65 Disassembly / Assembly .... page S-66 'd' ................. Inspection page S-65 8. Brace bar Removal / Installation ....... page S-84 Gartner Banana
Page 814 of 1708

DASHBOARD AND CONSOLE DASHBOARD AND CONSOLE COMPONENTS Removal l Installation 1. Disconnect the negative battery cable. Warning Handling the air bag module improperly can accidently deploy the air bag, which may seri- ously injure you. Read SERVICE WARNINGS, section T, before handling the air bag module. 2. Remove in the order shown in the figure, referring to Removal Note. To remove the dashboard, remove the control wires of the heater unit and blower unit. 3. Install in the reverse order of removal. 1. Ashtray 2. Change lever knob 3. Rear console assembly a. Back plate b. Shift lever boot 7. Speedometer cable 8. Instrument cluster 9. Center louver Removal Note ............. page S-57 10. Center an el assemblv c. Power window switch Removal Note ............. page S-58 d. Cover (Without power window) 1 1. Glove box assembly e. Console lock assembly 12. Passenger-side airbag module (if equipped) 4. Center lower panel assembly Removal 1 Installation ......... section T Removal Note ............. page S-57 13. Hood release knob -1 5. Steering shaft 14. Center hole cover 6. Meter hood assembly 15. Side cover Removal Note ............. page $57 16. Dashboard Gartner Banana
Page 815 of 1708
DASHBOARD AND CONSOLE s USA % CLlP CLIP 4 @ CANADA HOOK 0 05UOSX-10 Removal Note Center lower panel assembly The clips are where shown. Meter hood assembly The clips are where shown. Center louver 1. Thread a piece of string through the center louver. 2. Pull the string straight out while holding onto the center panel. Gartner Banana
Page 816 of 1708

DASHBOARD AND CONSOLE - / AIRFLOW MODE WIRE I _ -We -_ -, _ - 11 Center panel assembly The clips are where shown. Adjustment Note Airflow mode wire 1. Set the airflow mode control lever to VENT position. 2. Connect and clamp the wire with the shutter lever on the heater unit at its closest point. 3. Move the airflow mode control lever to make sure the wire is securely attached and that it moves the full stroke from DEF to VENT. REC-FRESH wire 1. Set the selector lever to FRESH position. 2. Connect and clamp the wire with the shutter lever on the blower unit at its closest point. 3. Move the REC-FRESH lever to make sure the wire is securely attached and that it moves the full stroke from - REC to FRESH. TEMF - - I 'ERATURE BLEND WIRE 45UOSX-080 Temperature blend wire 1. Set the temperature blend lever to MAX-HOT position. 2. Connect and clamp the wire with the shutter lever on the heater unit all the way to the right. 3. Move the temperature blend lever to make sure the wire is securely attached and that it moves the full stroke from HOT to COLD. Gartner Banana
Page 820 of 1708
FLOOR COVERING FLOOR COVERING COMPONENTS Removal / Installation 1. To remove the cabin carpet, first remove the following: a Seats (Refer to page S-65.) b Dashboard (Refer to page S-56.) c Heater unit (Refer to Section U) d Front side trim, scuff plates, quarter trim, and rear package trim (Refer to page S-59.) e Front seat belts and buckles (Refer to page S-63.) 2. Remove the remaining parts in the order shown in the figure. 3. Install in the reverse order of removal. 1. Rear end mat 2. Foot rest 3. Bracket 4. Cabin carpet Gartner Banana
Page 1058 of 1708
SRS AIR BAG SYSTEM T CRASH SENSOR (S-SENSOR) Removal 1 Installation 1. Carry out "Before Servicing" procedure under GENERAL PROCEDURES, page T-160. 2. Remove the dashboard. 3. Remove in the order shown in the figure. 4. Install in the reverse order of removal. 1. Nuts 2. Crash sensor 6-sensor) Installation note . . . .'. . . . . . . page T-214 T-213 Gartner Banana
Page 1078 of 1708
u HEATER HEATER UNIT Removal / Installation 1. Remove the dashboard. (Refer to section S.) 2. Remove the heater unit as shown in the figure. 3. Install in the reverse order of removal. 7.9-10.7 Nm (80-110 kgfcm, 69.5--95.4 In+bf] 1. Heater hose U-16 45UOUX4 2. Heater unit Gartner Banana