1994 JEEP CHEROKEE key battery

TILT STEERING COLUMN
DISASSEMBLY
(1) Remove the steering column from the vehicle,
if necessary. Refer to the removal procedure.
(2) If the column is removed for service, fabricate a
support fixture to clamp it in a vise (Fig. 1).
(3) If the steering column has not been removed
from the vehicle, place the front wheels in the
straight-ahead position. Disconnect the battery nega-
tive cable.
(4) Protect the painted areas on the steering col-
umn.
(5) Remove the steering wheel. Refer to the re-
moval procedure.
(6) Column shift: Remove the gear selector lever
retaining pin and the lever from the housing.
(7) Remove the lockplate cover. Use two small pry
bars to pry the cover off the lockplate.
WARNING: THE LOCKPLATE RETAINS A VERY
STRONG, SPRING FORCE. DO NOT ATTEMPT TO
REMOVE THE STEERING SHAFT RETAINING SNAP
RING WITHOUT USING LOCKPLATE COMPRESSOR
C-4156 (J-23653-B).
(8) Compress the lockplate with Lock Plate Com-
pressor C-4156 (J-23653-B) and release the steering
shaft retaining snap ring (Fig. 2).
(9) Remove the lockplate compressor tool and the
retaining snap ring. Discard the snap ring.
(10) Remove the lockplate, canceling cam, upper
bearing preload spring, and the thrust washer from
the steering column/shaft.(11) Remove the hazard warning switch knob.
Press the knob inward and remove it from the steer-
ing column by turning it counterclockwise.
(12) If the steering column is the column shift
type, remove the two retaining screws and the gear
selector indicator cover.
(13) If the steering column is the column shift
type, remove the gear selector indicator lamp bracket
retaining screw. Do not remove the lamp and bracket
at this time.
(14) Remove the tilt-release lever.
(15) Disconnect the turn signal wire harness con-
nector from the bracket located at the lower end of
the steering column (Fig. 3).
CAUTION: Wrap tape around the turn signal switch
wire harness connector to prevent it from becoming
entangled during removal.
(16) Remove the plastic protector from the wire
harness.
(17) Remove the turn signal switch retaining
screws (Fig. 4), dimmer switch actuator arm, to re-
move the switch. Guide the switch straight up and
out of the steering column.
(18) Remove the windshield wiper switch wire har-
ness and all the other wire harnesses located within
the steering column.
(19) Insert the ignition switch key into the key/
lock cylinder. Turn the key to the ON position.
Fig. 1 Steering Column Support Fixture
Fig. 2 Lockplate Snap Ring Removal
JSTEERING 19 - 59

(25) Install the windshield wiper wire harness and
switch. Route the wire harness down through steer-
ing column jacket.
(26) If equipped, install the cruise control wire har-
ness. Install the turn signal stalk by pushing it
straight into the column.
(27) Insert the hazard warning knob in the hazard
warning switch and press it inward. Align and install
the turn signal switch retaining screws. Ensure that
the turn signal switch is properly seated before tight-
ening the screws. Tighten the screws to 4 Nzm (33 in.
lbs.) torque. Thread the hazard warning switch knob
into the switch and pull the knob outward.
(28) Install and seat the upper bearing race in the
key/lock cylinder housing.
(29) Install the upper bearing preload spring, the
canceling cam and the lockplate.
(30) Install a replacement lockplate retaining snap
ring on the sleeve of the Lock Plate Compressor C-
4156 (J-23653-B). Install the tool on the steering
shaft (Fig. 27).
(31) Compress the lockplate with the compressor
tool and position the retaining snap ring in the steer-
ing shaft groove.
(32) Remove the compressor tool. Ensure that the
retaining ring is completely seated in the groove be-
fore removing the tool.
(33) Position the wire harness protectors, if
equipped, over the wire harnesses and snap them in
place on the steering column.
(34) Install the lockplate cover.
(35) Install the steering wheel. Refer to the instal-
lation procedure.
(36) Insert the ignition key in the key/lock cylin-
der; turn the cylinder to the OFF-UNLOCK position ;
move the ignition switch downward to eliminateany switch-to-remote rod lash; and tighten the igni-
tion switch attaching screws to 4 Nzm (35 in. lbs.)
torque.
(37) Depress the dimmer switch slightly and insert
a 3/32-inch drill bit into the adjustment hole.
(38) Loosen the retaining screws and move the
dimmer switch toward the steering wheel to remove
any lash. Tighten the dimmer switch retaining
screws to 4 Nzm (35 in. lbs.) torque.
(39) Remove the drill bit and test operation by
moving the dimmer switch stalk. Test the dimmer
switch operation in the full-up, down and center
steering wheel positions.
(40) Install the steering column and steering
wheel. Refer to the installation procedure.
(41) Connect the battery negative cable.
Fig. 27 Lockplate Retaining Ring Installation
19 - 68 STEERINGJ

COMPRESSOR OVERHAUL
INDEX
page page
Compressor............................. 17
Compressor Isolation...................... 17
Description............................. 17Magnetic Clutch......................... 18
Purging Compressor of Air................. 17
DESCRIPTION
The A/C system uses a Sanden compressor. This
compressor is a 7 piston design. Designated the SD-
709, the compressor is mounted on the front right
side of the engine and is driven by a serpentine belt.
System lubrication is provided by 135cc615cc (4.6
cu. in.60.5 cu. in.) of 500 viscosity refrigerant oil.
The clutch used on the compressor consists of 3 ba-
sic components: the pulley, front plate and the field
coil. The pulley and field coil are attached to the
front head of the compressor with tapered snap rings.
The hub is keyed to the compressor shaft and is re-
tained on the shaft with a self-locking nut. Special
service tools are required to remove and install the
clutch plate on the compressor shaft.
COMPRESSOR ISOLATION
It is not necessary to discharge the system for com-
pressor removal. The compressor can be isolated from
the remainder of the system and eliminate the need
for recharging when performing compressor service.
(1) Connect pressure gauge and manifold.
(2) Close both gauge hand valves.
(3) Mid-position both service valves.
WARNING: USE EXTREME CAUTION WHEN THE
ENGINE IS OPERATING. DO NOT STAND IN A DI-
RECT LINE WITH THE FAN. DO NOT PUT YOUR
HANDS NEAR THE PULLEYS, BELTS OR FAN. DO
NOT WEAR LOOSE CLOTHING.
(4) Start the engine and operate the air condition-
ing system.
(5) Turn the suction service valve slowly clockwise
toward the front seated position.
(6) When pressure drops to zero, stop the engine
and compressor and quickly finish front-seating the
suction service valve.
(7) Front-seat the discharge service valve.
(8) Loosen the oil level check plug slowly to re-
lease any internal pressure in the compressor.
The compressor is now isolated from the remainder
of the system.
The service valves can be removed from the com-
pressor.
PURGING COMPRESSOR OF AIR
The compressor must be purged of air whenever it
has been isolated for an oil level check or other ser-
vice procedures without discharging the entire sys-
tem.
(1) Cap the service gauge ports on both of the ser-
vice valves.
(2) Back-seat the suction service valve to allow the
system refrigerant to enter the compressor.
(3) Place the discharge service valve in the mid-po-
sition or cracked-position.
(4) Loosen the discharge service valve gauge port
cap to permit the refrigerant to force any air out of
the compressor.
(5) Back-seat the discharge service valve and
tighten the gauge port cap.
(6) The compressor is now ready for service.
COMPRESSOR
REMOVAL
(1) Isolate the compressor.
(2) Disconnect negative cable from battery.
(3) Disconnect the clutch lead wire.
(4) Remove the discharge and inlet (suction) ser-
vice valves from the compressor. Plug or tape all the
openings.
(5) Remove the serpentine drive belt (refer to
Group 7, Cooling System for the proper procedure).
(6) Remove the bolts and lift the compressor from
the mounting bracket (Figs. 1 and 2).
INSTALLATION
If a replacement compressor is being installed;
check the oil level. Add or subtract oil as neces-
sary and install the magnetic clutch on the com-
pressor.
(1) If the mounting bracket was removed, install
the bracket to the block. Tighten the mounting bolts
to 27 NIm (20 ft. lbs.) torque.
(2) Install the compressor on the mounting
bracket. Tighten the bolts to 27 NIm (20 ft. lbs.)
torque.
(3) Install the serpentine drive belt (refer to Group
7, Cooling System for the proper procedure).
(4) Tighten the serpentine drive belt to the speci-
fied tension.
²New belt tensionÐ800-900 N (180-200 lb-f).
JHEATING AND AIR CONDITIONING 24 - 17

DIAGNOSTIC INSPECTIONS, STARTER
SYSTEM............................8A-9
DIAGNOSTIC PROCEDURES;
ELECTRICAL........................8A-15
DIAGNOSTIC PROCEDURES; OVERHEAD
CONSOLE...........................8C-1
DIAGNOSTIC SYSTEM, USING ON-
BOARD............................8A-19
DIAGNOSTIC TROUBLE CODE,
CHECKING FOR.......................8H-5
DIAGNOSTIC TROUBLE CODE (DTC),
GENERATOR........................8A-19
DIAGNOSTIC TROUBLE CODES, INDICATOR
(CHECK ENGINE) LAMP...............8A-19
DIAGNOSTICS, BATTERY/STARTING/
CHARGING SYSTEMS..................8A-1
DIAGNOSTICS CHART, BATTERY...........8A-7
DIAGNOSTICS (OBD), ON-BOARD;
COOLING SYSTEM.....................7-4
DIAGNOSTICS (OBD), ON-BOARD; FUEL
SYSTEM............................14-48
DIAGNOSTICS (OBD), ON-BOARD;
IGNITION SYSTEMS..................8D-19
DIAGNOSTICS/SERVICE PROCEDURES......8D-8
DIAGRAM, AIRFLOW...................24-23
DIAGRAM SHEETS AND INDEXES,
WIRING............................8W-1
DIAGRAMS, WIRING....................8A-1
DIAGRAMS YJ, WIRING................8W-73
DIFFERENTIAL AND PINION MEASUREMENT;
FRONT SUSPENSION AND AXLE..........2-38
DIFFERENTIAL AND PINION
MEASUREMENT; REAR SUSPENSION
AND AXLES..........................3-20
DIFFERENTIAL ASSEMBLY; FRONT
SUSPENSION AND AXLE................2-36
DIFFERENTIAL ASSEMBLY; REAR
SUSPENSION AND AXLES...............3-19
DIFFERENTIAL DISASSEMBLY; FRONT
SUSPENSION AND AXLE................2-34
DIFFERENTIAL DISASSEMBLY; REAR
SUSPENSION AND AXLES...............3-17
DIFFERENTIAL INSTALLATION; FRONT
SUSPENSION AND AXLE................2-43
DIFFERENTIAL INSTALLATION; REAR
SUSPENSION AND AXLES...............3-24
DIFFERENTIAL, LIMITED SLIP..............3-8
DIFFERENTIAL OVERHAUL................3-45
DIFFERENTIAL REMOVAL; FRONT
SUSPENSION AND AXLE................2-32
DIFFERENTIAL REMOVAL; REAR
SUSPENSION AND AXLES...............3-16
DIFFERENTIAL SERVICE..................3-33
DIFFERENTIAL SHIM PACK
MEASUREMENT AND ADJUSTMENT.......2-42
DIFFERENTIAL, TRAC-LOK................3-44
DIMENSION DATA, VEHICLE . . . INTRO.-3,INTRO.-4
DIMENSIONS, AW-4 VALVE BODY CHECK
BALL.............................21-328
DIMENSIONS, DESIGNATIONS, LABELS/
PLATES, CODES...................INTRO.-1
DIMMER SWITCH REPLACEMENT,
HEADLAMP..........................8L-6
DIRECT CLUTCH OVERHAUL............21-219
DISASSEMBLY........................19-59
DISASSEMBLY AND INSPECTION, VALVE
BODY.............................21-138
DISASSEMBLY AND OVERHAUL,
TRANSFER CASE..............21-277,21-297
DISASSEMBLY AND OVERHAUL,
TRANSMISSION; TRANSMISSION AND
TRANSFER CASE.................21-5,21-36
DISASSEMBLY, CALIPER.................5-27
DISASSEMBLYÐCOLUMN OR CONSOLE
SHIFT..............................19-50
DISASSEMBLY, DIFFERENTIAL; FRONT
SUSPENSION AND AXLE................2-34
DISASSEMBLY, DIFFERENTIAL; REAR
SUSPENSION AND AXLES...............3-17
DISASSEMBLY, GEAR...................19-37
DISASSEMBLY INFORMATION, GEAR.......19-24
DISASSEMBLY, TRANSMISSION
....21-112,21-192
DISC AND PLATE THICKNESS, AW-4
CLUTCH
...........................21-325
DISC BRAKE ROTOR REFINISHING
.........5-32
DISC BRAKE ROTOR RUNOUT
.............5-31DISC BRAKE ROTOR THICKNESS..........5-31
DISC BRAKE ROTOR THICKNESS
VARIATION..........................5-31
DISC BRAKES..........................5-24
DISC BRAKESHOE INSTALLATION..........5-26
DISC BRAKESHOE REMOVAL..............5-25
DISC INSTALLATION, CLUTCH COVER.......6-10
DISC REMOVAL, CLUTCH COVER..........6-10
DISCHARGE, SYSTEM...................24-4
DISCONNECT AXLEÐYJ VEHICLES,
VACUUM............................2-26
DISCONNECT AXLE/SHIFT MOTOR
DIAGNOSIS..........................2-27
DISPLAY, ABS WARNING LIGHT............5-3
DISPLAY, BRAKE WARNING LIGHT..........5-4
DISPLAY SYMBOLS, INTERNATIONAL
VEHICLE CONTROL................INTRO.-3
DISPLAY SYMBOLS, VEHICLE CONTROL . INTRO.-7
DISPOSAL, LIFTGATE SUPPORT ROD
CYLINDER..........................23-70
DISTRIBUTOR........................8D-23
DISTRIBUTOR CAP.....................8D-9
DISTRIBUTOR CAP AND ROTOR, IGNITION
CABLES.............................0-18
DISTRIBUTOR ROTOR..................8D-10
DISTRIBUTORS........................8D-3
DOME LAMP REPLACEMENT.............8L-20
DOME/CARGO LAMP BULB
REPLACEMENTÐYJ VEHICLES,
HARDTOP..........................8L-20
DOME/COURTESY LAMP SERVICE
INFORMATION.......................8L-19
DOME/COURTESY LAMP TROUBLE
DIAGNOSIS.........................8L-19
DOOR ALIGNMENT ADJUSTMENTÐ
MAJOR............................23-47
DOOR ALIGNMENT ADJUSTMENTÐ
MINOR.............................23-46
DOOR ALIGNMENTÐMINOR, XJ..........23-46
DOOR ASSIST HANDLE, FULL-METAL.....23-175
DOOR BUMPERS, FUEL FILLER...........23-31
DOOR CONTROL CABLES, VENT..........24-39
DOOR EDGE GUARD/EDGE PROTECTOR
STRIP.............................23-61
DOOR EXTERNAL HANDLE...............23-55
DOOR FIXED WINDOW GLASS, REAR......23-53
DOOR, HALF-METAL SOFT TOP..........23-173
DOOR HINGE/HINGE PIN REPLACEMENT . . . 23-58
DOOR HINGES, FULL-METAL............23-179
DOOR INSIDE LATCH RELEASE AND
LOCK RODS.........................23-57
DOOR KEY LOCK CYLINDER.............23-54
DOOR KEY LOCK CYLINDER, FULL-METAL . 23-178
DOOR LATCH.........................23-56
DOOR LATCH ADJUSTMENT.............23-55
DOOR LATCH EXTERNAL RELEASE
HANDLE, FULL-METAL...............23-178
DOOR LATCH, FULL-METAL.............23-179
DOOR LATCH INSIDE RELEASE AND
LOCK HANDLE, FULL-METAL..........23-175
DOOR LATCH STRIKER, HALF-METAL.....23-175
DOOR LOCK SWITCH, PASSENGER.........8P-5
DOOR LOCKS, DIAGNOSING POWER . . . 8P-1,8P-9
DOOR LOCKS, POWER..................8P-10
DOOR LOCK/UNLOCK RELAY
REPLACEMENT......................8P-12
DOOR MIRROR (EXTERNAL), HALF METAL . . 23-158
DOOR MOTOR SWITCH REPLACEMENT,
BLOWER MOTOR/AIR.................24-39
DOOR OPENING WEATHERSTRIP SEALS,
DOOR WINDOW GLASS...............23-62
DOOR POWER LOCK SWITCHÐ2-DOOR
LEFT HAND DRIVE, DRIVERS............8P-2
DOOR POWER LOCK SWITCHÐ2-DOOR
RIGHT HAND DRIVE, DRIVERS...........8P-3
DOOR POWER LOCK SWITCHÐ4-DOOR,
DRIVERS............................8P-4
DOOR POWER WINDOW SWITCHÐ2-DOOR
LEFT HAND DRIVE, DRIVERS............8S-6
DOOR POWER WINDOW SWITCHÐ2-DOOR
RIGHT HAND DRIVE, DRIVERS...........8S-7
DOOR POWER WINDOW SWITCHÐ4-DOOR,
DRIVERS
............................8S-5
DOOR REMOVAL/INSTALLATION
..........23-40
DOOR RESTRAINT REPLACEMENT
........23-47
DOOR SERVICE, FULL-METAL
...........23-181DOOR SPACER BLOCKSÐTWO-DOOR
VEHICLES, FRONT....................23-60
DOOR TRIM PANEL....................23-35
DOOR TRIM PANEL, FULL-METAL........23-175
DOOR VACUUM MOTOR, FRESH AIR.......24-41
DOOR VACUUM MOTOR REPLACEMENT,
A/C RECIRCULATING AIR..............24-31
DOOR VACUUM MOTOR REPLACEMENT,
HEATER/DEFROSTER/INSTRUMENT
PANEL OUTLET......................24-30
DOOR VENT WINDOW, FRONT............23-50
DOOR VENT WINDOW GLASS, FULL-
METAL............................23-177
DOOR WATERDAM, FULL-METAL.........23-176
DOOR WEATHERSTRIP SEALS, FULL-
METAL............................23-180
DOOR WINDOW EXTERIOR MOULDINGS....23-61
DOOR WINDOW GLASS AND DOOR
OPENING WEATHERSTRIP SEALS........23-62
DOOR WINDOW GLASS, FRONT..........23-49
DOOR WINDOW GLASS, FULL-METAL.....23-178
DOOR WINDOW GLASS, REAR...........23-52
DOOR WINDOW GLASS REGULATOR,
FRONT.............................23-48
DOOR WINDOW GLASS REGULATOR,
FULL-METAL.......................23-177
DOOR WINDOW GLASS REGULATOR
HANDLE, FULL-METAL...............23-175
DOOR WINDOW GLASS REGULATOR,
REAR..............................23-51
DOOR WINDOW SWITCH, PASSENGER......8S-8
DOORS........................23-34,23-173
DOUBLE CARDAN (CV)..................16-10
DOWNSHIFT, HYDRAULIC FLOW DURING
FULL THROTTLE 3-2..................21-92
DOWNSHIFT, HYDRAULIC FLOW DURING
PART THROTTLE 3-2..................21-91
DRAG LINK......................19-14,19-17
DRAINING COOLING SYSTEM.............7-16
DRAW (IOD) DIAGNOSIS, IGNITION OFF.....8A-8
DRB SCAN TOOL; COOLING SYSTEM........7-5
DRB SCAN TOOL; EMISSION CONTROL
SYSTEMS...........................25-2
DRB SCAN TOOL; FUEL SYSTEM..........14-51
DRB SCAN TOOL; IGNITION SYSTEMS.....8D-10
DRIERÐ2.5L ENGINES, CONDENSER/
RECEIVER..........................24-31
DRIERÐ4.0L ENGINES, RECEIVER........24-32
DRIP RAIL MOULDINGÐXJ VEHICLES.....23-29
DRIVE AXLE ASSEMBLY REPLACEMENTÐXJ
VEHICLES; FRONT SUSPENSION AND
AXLE...............................2-21
DRIVE AXLE ASSEMBLY REPLACEMENTÐ
XJ VEHICLES; REAR SUSPENSION
AND AXLES......................3-11,3-30
DRIVE AXLE ASSEMBLY REPLACEMENTÐ
YJ VEHICLES; FRONT SUSPENSION
AND AXLE...........................2-21
DRIVE AXLE ASSEMBLY REPLACEMENTÐ
YJ VEHICLES; REAR SUSPENSION
AND AXLES..........................3-12
DRIVE AXLE, FRONT.....................2-3
DRIVE, BATTERY CLASSIFICATIONS AND
RATINGSÐLEFT HAND................8B-10
DRIVE, BATTERY CLASSIFICATIONS AND
RATINGSÐRIGHT HAND...............8B-10
DRIVE, BATTERY REPLACEMENTÐLEFT
HAND..............................8B-1
DRIVE, BATTERY REPLACEMENTÐ
RIGHT HAND.........................8B-2
DRIVE BELT, ACCESSORY................0-20
DRIVE BELT DIAGNOSIS, SERPENTINE......7-32
DRIVE, BELT SERVICEÐEXCEPT RIGHT
HAND...............................7-34
DRIVE, BELT SERVICEÐWITH RIGHT
HAND...............................7-35
DRIVE BELT TENSION...................7-38
DRIVE BELTS, ENGINE ACCESSORY........7-31
DRIVE, DRIVERS DOOR POWER LOCK
SWITCHÐ2-DOOR LEFT HAND
...........8P-2
DRIVE, DRIVERS DOOR POWER LOCK
SWITCHÐ2-DOOR RIGHT HAND
.........8P-3
DRIVE, DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR LEFT HAND
...........8S-6
DRIVE, DRIVERS DOOR POWER WINDOW
SWITCHÐ2-DOOR RIGHT HAND
.........8S-7
JINDEX7
Description Group-Page Description Group-Page Description Group-Page

GRILLE OPENING PANEL (GOP), GRILLE.....23-3
GRILLEÐXJ VEHICLES, AIR EXHAUST.....23-30
GROUND, POWER.....................14-22
GROUP INDEX; ELECTRICAL..............8A-1
GUARD, BRUSH........................23-3
GUARD/EDGE PROTECTOR STRIP, DOOR
EDGE..............................23-61
GUIDES AND CHARTS, DIAGNOSIS........21-76
HALF METAL DOOR MIRROR (EXTERNAL) . . 23-158
HALF-METAL DOOR LATCH STRIKER......23-175
HALF-METAL SOFT TOP DOOR..........23-173
HAND DRIVE, BATTERY CLASSIFICATIONS
AND RATINGSÐLEFT.................8B-10
HAND DRIVE, BATTERY CLASSIFICATIONS
AND RATINGSÐRIGHT................8B-10
HAND DRIVE, BATTERY REPLACEMENTÐ
LEFT...............................8B-1
HAND DRIVE, BATTERY REPLACEMENTÐ
RIGHT..............................8B-2
HAND DRIVE, BELT SERVICEÐEXCEPT
RIGHT..............................7-34
HAND DRIVE, BELT SERVICEÐWITH
RIGHT..............................7-35
HAND DRIVE, DRIVERS DOOR POWER
LOCK SWITCHÐ2-DOOR LEFT...........8P-2
HAND DRIVE, DRIVERS DOOR POWER
LOCK SWITCHÐ2-DOOR RIGHT..........8P-3
HAND DRIVE, DRIVERS DOOR POWER
WINDOW SWITCHÐ2-DOOR LEFT........8S-6
HAND DRIVE, DRIVERS DOOR POWER
WINDOW SWITCHÐ2-DOOR RIGHT......8S-7
HAND DRIVE, GENERATOR
REPLACEMENTÐLEFT.................8B-7
HAND DRIVE, GENERATOR
REPLACEMENTÐRIGHT................8B-9
HAND DRIVE (RHD), BELT TENSIONÐ
EXCEPT RIGHT.......................7-33
HAND DRIVE (RHD), BELT TENSIONÐ
RIGHT..............................7-34
HAND DRIVE VEHICLES, RIGHT............23-1
HAND DRIVE, WASHER PUMP
REPLACEMENTÐLEFT.................8K-2
HAND DRIVE, WASHER PUMP
REPLACEMENTÐRIGHT................8K-3
HANDLE, DOOR EXTERNAL..............23-55
HANDLE, FULL-METAL DOOR ASSIST.....23-175
HANDLE, FULL-METAL DOOR LATCH
EXTERNAL RELEASE.................23-178
HANDLE, FULL-METAL DOOR LATCH
INSIDE RELEASE AND LOCK...........23-175
HANDLE, FULL-METAL DOOR WINDOW
GLASS REGULATOR.................23-175
HANDLE, TAILGATE LATCH AND
RELEASE..........................23-160
HANDLEÐXJ VEHICLES, ASSIST.........23-118
HANGER BRACKET, MUFFLER/TAILPIPE.....13-16
HARD TOP DOME/CARGO LAMP BULB
REPLACEMENTÐYJ VEHICLES..........8L-20
HARD TOP LIFTGATE GLASS............23-162
HARD TOP QUARTER WINDOW GLASS....23-188
HARD TOP REPAIR....................23-165
HARD TOP ROOF VENT................23-165
HARD TOP SERVICE...................23-164
HARD TOP SERVICE INFORMATION.......23-164
HAZARD LAMPSÐXJ....................8J-1
HAZARD LAMPSÐYJ....................8J-2
HCU DIAGNOSIS........................5-4
HCU INSTALLATIONÐXJ.................5-54
HCU INSTALLATIONÐYJ.................5-54
HCU PUMP AND PEDAL TRAVEL
SENSOR OPERATION...................5-44
HCU REMOVALÐXJ.....................5-53
HCU REMOVALÐYJ.....................5-54
HCU SOLENOID VALVE OPERATION.........5-43
HEAD COVER, ENGINE CYLINDER......9-18,9-59
HEAD, ENGINE CYLINDER............9-19,9-60
HEAD GASKET FAILURE DIAGNOSIS,
ENGINE CYLINDER.....................9-5
HEADLAMP BEAM ADJUSTMENT...........8L-3
HEADLAMP BULB REPLACEMENT
..........8L-3
HEADLAMP DELAY FUNCTION TROUBLE
DIAGNOSISÐXJ VEHICLES
.............8L-16
HEADLAMP DELAY MODULE
REPLACEMENTÐXJ VEHICLES
..........8L-16
HEADLAMP DELAY MODULEÐXJ
VEHICLES, SENTINEL
.................8L-15HEADLAMP DIMMER SWITCH
REPLACEMENT.......................8L-6
HEADLAMP SWITCH REPLACEMENT........8L-4
HEADLAMP SWITCH/ILLUMINATION
RHEOSTAT..........................8E-21
HEADLAMP TROUBLE DIAGNOSISÐ
XJ VEHICLES.........................8L-1
HEADLAMP TROUBLE DIAGNOSISÐYJ
VEHICLES...........................8L-2
HEADLAMPS...........................0-35
HEADLINER.........................23-121
HEAT SHIELDS........................14-12
HEAT SHIELDS, EXHAUST................11-1
HEAT SHIELDS, MUFFLER AND TAILPIPE . . . 13-17
HEATER AND A/C CONTROL PANEL
REPLACEMENT......................24-26
HEATER CONTROL CABLE REPLACEMENT . . . 24-30
HEATER CONTROL PANEL REPLACEMENT . . . 24-39
HEATER CORE........................24-28
HEATER CORE AND HOUSING............24-40
HEATER CORE HOUSING REPLACEMENT . . . 24-29
HEATER, ENGINE BLOCK.................7-37
HEATER/DEFROSTER OPERATION.........24-37
HEATER/DEFROSTER/INSTRUMENT
PANEL OUTLET DOOR VACUUM MOTOR
REPLACEMENT......................24-30
HEATING ELEMENT TEST, OXYGEN
SENSOR (O2S)......................14-45
HEATING SCHEMATIC...................24-24
HEATING SYSTEM DIAGNOSIS............24-11
HEATING SYSTEMÐYJ VEHICLES.........24-14
HIGH LINE CLUSTER...................8E-12
HIGH MOUNTED STOP LAMP (CHMSL)Ð
XJ, CENTER.........................8L-10
HIGH MOUNTED STOP LAMP (CHMSL)Ð
YJ, CENTER.........................8L-11
HINGE, LIFTGATE......................23-67
HINGE REPLACEMENT, HOOD.............23-9
HINGE, TAILGATE.....................23-159
HINGE/HINGE PIN REPLACEMENT, DOOR . . . 23-58
HINGES, FULL-METAL DOOR............23-179
HITCHES, TRAILER.....................23-88
HOISTING AND TOWING, JUMP
STARTING,............................0-7
HOLDDOWN AND FLOOR BRACKETSÐ
XJ VEHICLES, SPARE TIRE/WHEEL......23-128
HONING CYLINDER BORES................9-2
HOOD..........................23-6,23-137
HOOD ADJUSTMENT....................23-9
HOOD ALIGNMENT....................23-138
HOOD HINGE REPLACEMENT..............23-9
HOOD INSULATOR PANEL..............23-138
HOOD LATCH REPLACEMENT............23-10
HOOD LATCH STRIKER REPLACEMENT.....23-10
HOOD SAFETY LATCH.................23-139
HOOKÐXJ VEHICLES, REAR TOW.........23-87
HOOKS, FRONT TOW....................13-5
HOOKS, TOW.........................13-14
HORN PAD REPLACEMENT, HORN SWITCH . . . 8G-3
HORN SWITCH (HORN PAD)
REPLACEMENT.......................8G-3
HOSE REPLACEMENT, PRESSURE AND
RETURN............................19-9
HOSE ROUTING SCHEMATICS,
VACUUM............................25-1
HOSE SPLASH SHIELDÐXJ VEHICLES,
FUEL FILLER........................23-86
HOSES, BRAKE BLEEDINGÐBRAKE FLUID
AND LEVELÐBRAKELINES..............5-13
HOSES, BRAKELINES....................5-15
HOSES, COOLING SYSTEM...............7-26
HOSES/TUBING, RUBBER AND PLASTIC.....0-28
HOUSING, AIR CLEANER; EMISSION
CONTROL SYSTEMS...................25-8
HOUSING, AIR CLEANER; FUEL SYSTEM....14-54
HOUSING AND PARK LOCK COMPONENT
OVERHAUL, ADAPTER................21-120
HOUSING END PLUG...................19-26
HOUSING, EVAPORATOR................24-42
HOUSING, EVAPORATOR/BLOWER.........24-33
HOUSING, HEATER CORE................24-40
HOUSING LEAK DIAGNOSIS, CONVERTER
. . . 21-73
HOUSING, LIFTGATE LICENSE PLATE
LAMP
..............................23-72
HOUSING REPLACEMENT, CLUTCH
.........6-11
HOUSING REPLACEMENT, HEATER CORE
. . . 24-29HOUSING SEAL REPLACEMENT,
ADAPTER..........................21-182
HOUSINGS, INSTRUMENT CLUSTER
AND GAUGE........................23-190
HUB BEARING AND AXLE SHAFT...........2-24
HYDRAULIC CLUTCH....................0-22
HYDRAULIC COMPONENTS................5-1
HYDRAULIC CONTROL UNIT (HCU).........5-39
HYDRAULIC FLOW DURING FULL
THROTTLE 3-2 DOWNSHIFT............21-92
HYDRAULIC FLOW DURING PART
THROTTLE 3-2 DOWNSHIFT............21-91
HYDRAULIC FLOW IN D RANGE FIRST
GEAR..............................21-87
HYDRAULIC FLOW IN D RANGE SECOND
GEAR..............................21-88
HYDRAULIC FLOW IN D RANGE THIRD
GEAR..............................21-89
HYDRAULIC FLOW IN MANUAL FIRST
GEAR (1) POSITION..................21-94
HYDRAULIC FLOW IN MANUAL SECOND
(2) RANGE..........................21-93
HYDRAULIC FLOW IN PARK AND NEUTRAL . . . 21-86
HYDRAULIC FLOW IN REVERSE..........21-95
HYDRAULIC FLOW IN THIRD GEAR
(CONVERTER CLUTCH ENGAGED)........21-90
HYDRAULIC LINKAGE INSTALLATION,
CLUTCH.............................6-12
HYDRAULIC LINKAGE REMOVAL,
CLUTCH.............................6-11
HYDRAULIC PRESSURE TEST......21-71,21-168
HYDRAULIC SYSTEM..................21-160
HYDRAULIC TAPPETS...............9-24,9-65
HYDROMETER TEST....................8A-3
IDENTIFICATION, AW-4 VALVE AND
SPRING...........................21-330
IDENTIFICATION, CIRCUIT................8W-2
IDENTIFICATION, COMPONENT............8W-2
IDENTIFICATION, ENGINE AND
TRANSMISSION/TRANSFER CASE.....INTRO.-3
IDENTIFICATION, MAJOR COMPONENT . . INTRO.-3
IDENTIFICATION NUMBER (VIN)
DECODING, VEHICLE...............INTRO.-2
IDENTIFICATION NUMBER (VIN) PLATE,
VEHICLE.........................INTRO.-1
IDENTIFICATION, TRANSFER CASE
. 21-273,21-293
IDENTIFICATION, TRANSMISSION
.....21-1,21-32,
21-66,21-157
IDENTIFICATION, WIRE CODE
.............8W-2
IDENTIFICATION, WIRING AND
COMPONENT
.......................8W-13
IDLE AIR CONTROL (IAC) MOTOR
.........14-56
IDLE AIR CONTROL (IAC) MOTORÐPCM
OUTPUT
............................14-25
IDLE AIR CONTROL MOTOR TEST
.........14-46
IDLE SWITCHÐPCM INPUT, EXTENDED
....14-21
IDLE SWITCH TEST, EXTENDED
...........14-45
IGNITION CABLES, DISTRIBUTOR CAP
AND ROTOR
.........................0-18
IGNITION CIRCUIT SENSEÐPCM INPUT
....14-21
IGNITION COIL; FUEL SYSTEM
...........14-57
IGNITION COIL; IGNITION SYSTEMS
. . 8D-4,8D-11,
8D-26
IGNITION COILÐPCM OUTPUT
...........14-26
IGNITION COIL RESISTANCE
.............8D-11
IGNITION KEY WARNING SWITCH
REPLACEMENT
.......................8U-4
IGNITION OFF DRAW (IOD) DIAGNOSIS
.....8A-8
IGNITION SECONDARY CIRCUIT
DIAGNOSIS
.........................8D-12
IGNITION SWITCH; BRAKES
...............5-42
IGNITION SWITCH CONTINUITY TESTS
.....8D-31
IGNITION SWITCH; IGNITION SYSTEMS
....8D-30
IGNITION SWITCH INSTALLATION/
ADJUSTMENT
.......................8D-31
IGNITION SWITCH REMOVAL
............8D-30
IGNITION SWITCH TESTING
.............8D-30
IGNITION TIMING
......................8D-14
IGNITION WIRING, SECONDARY
...........8W-1
ILLUMINATED ENTRY SYSTEM SERVICE
INFORMATION
.......................8L-20
ILLUMINATED ENTRY SYSTEM TROUBLE
DIAGNOSIS
....................8L-21,8L-22
JINDEX11
Description Group-Page Description Group-Page Description Group-Page

LIFTGATE LOCK CYLINDER
REPLACEMENT.......................8P-7
LIFTGATE OPENING WEATHERSTRIP SEAL . . . 23-70
LIFTGATE PILLAR TRIM COVERSÐXJ
VEHICLES.........................23-116
LIFTGATE REMOVAL/INSTALLATION........23-65
LIFTGATE SERVICE INFORMATIONÐXJ
VEHICLES..........................23-65
LIFTGATE SUPPORT ROD BALL
STUD REPLACEMENT.................23-70
LIFTGATE SUPPORT ROD CYLINDER.......23-69
LIFTGATE SUPPORT ROD CYLINDER
DISPOSAL..........................23-70
LIFTGATE TRIM PANEL.................23-66
LIFTGATE WINDOW GLASSÐXJ
VEHICLES..........................23-81
LIFTGATE WIPER.......................8K-5
LIFTGATE WIPER SWITCH REPLACEMENT....8K-6
LIGHT DISPLAY, ABS WARNING............5-3
LIGHT DISPLAY, BRAKE WARNING..........5-4
LIGHTED VANITY MIRROR...............8L-19
LIGHTED VANITY MIRROR TROUBLE
DIAGNOSIS.........................8L-19
LIGHTS, BRAKE WARNING.................5-1
LIGHTS (CANADA ONLY), DAYTIME
RUNNING...........................8L-16
LIGHTS, SYSTEM WARNING..............5-42
LIMITED SLIP DIFFERENTIAL...............3-8
LIMITS, AW-4 OIL PUMP WEAR.........21-325
LINE CLUSTER, HIGH...................8E-12
LINE CLUSTER, LOW...................8E-11
LINE FITTINGS, TRANSMISSION COOLER . . 21-187
LINERS, REAR WHEELHOUSE FLARES.....23-18
LINERS, WHEELHOUSE SPLASH.........23-146
LINES AND FITTINGS, SERVICING
TRANSMISSION COOLER.............21-106
LINK CONNECTORÐPCM INPUT, DATA.....14-20
LINK CONNECTORÐPCM OUTPUT, DATA . . . 14-24
LINK, DRAG.....................19-14,19-17
LINK REPLACEMENT, FUSIBLE............8W-4
LINKAGE ADJUSTMENT, SHIFT....21-275,21-296
LINKAGE ADJUSTMENT (YJ), GEARSHIFT . . . 21-96
LINKAGE AND BALL STUDS, STEERING.....0-30
LINKAGE FLUID, CLUTCH..................6-1
LINKAGE, GEARSHIFT..................21-70
LINKAGE INSTALLATION, CLUTCH
HYDRAULIC..........................6-12
LINKAGE REMOVAL, CLUTCH HYDRAULIC....6-11
LINKAGEÐXJ, STEERING..........19-14,19-73
LINKAGEÐYJ, STEERING..........19-17,19-73
LINKS, FUSIBLE.......................8W-3
LOAD DATA, VEHICLE................INTRO.-3
LOAD DATA, XJ VEHICLE.............INTRO.-5
LOAD DATA, YJ-VEHICLE.............INTRO.-6
LOAD TEST, BATTERY...................8A-4
LOCATING A SYSTEM...................8W-2
LOCATIONS, SPLICE..............8W-2,8W-53
LOCATIONS, TRANSMISSION SWITCH
AND PLUG..........................21-33
LOCATIONS, XJ RHD SPLICE............8W-67
LOCATIONS, XJ SPLICE................8W-59
LOCATIONS, YJ SPLICE................8W-53
LOCK COMPONENT OVERHAUL,
ADAPTER HOUSING AND PARK........21-120
LOCK COMPONENT REPLACEMENT,
PARK .............................21-102
LOCK CYLINDER, DOOR KEY.............23-54
LOCK CYLINDER, FULL-METAL DOOR
KEY ..............................23-178
LOCK CYLINDER REPLACEMENT,
LIFTGATE............................8P-7
LOCK CYLINDER, TAILGATE.............23-160
LOCK CYLINDER/STRIKER, LIFTGATE
LATCH/KEY.........................23-68
LOCK CYLINDERS, KEY............23-2,23-132
LOCK HANDLE, FULL-METAL DOOR.......23-175
LOCK, HYDROSTATIC.....................9-4
LOCK RODS, DOOR INSIDE LATCH
RELEASE...........................23-57
LOCK SWITCH, PASSENGER DOOR
.........8P-5
LOCK SWITCHÐ2-DOOR LEFT HAND
DRIVE, DRIVERS DOOR POWER
..........8P-2
LOCK SWITCHÐ2-DOOR RIGHT HAND
DRIVE,DRIVERS DOOR POWER
..........8P-3
LOCK SWITCHÐ4-DOOR, DRIVERS
DOOR POWER
........................8P-4LOCKS, DIAGNOSING POWER DOOR . . . 8P-1,8P-9
LOCKS, POWER; ELECTRICAL.............8A-1
LOCKS, POWER; POWER DOOR LOCKS.....8P-1
LOCKS, POWER DOOR..................8P-10
LOCK/UNLOCK RELAY REPLACEMENT,
DOOR.............................8P-12
LOOP MODES OF OPERATION, OPEN
LOOP/CLOSED.......................14-27
LOOP/CLOSED LOOP MODES OF
OPERATION, OPEN...................14-27
LOSS OF SENSOR INPUT..................5-3
LOW FUEL WARNING INOPERATIVE........8E-4
LOW FUEL WARNING LAMP..............8E-2
LOW LINE CLUSTER...................8E-11
LOW SPEED KNOCK; FRONT SUSPENSION
AND AXLE...........................2-17
LOW SPEED KNOCK; REAR SUSPENSION
AND AXLES...........................3-8
LOW WASHER INDICATOR INOPERATIVE....8E-4
LOWER SUSPENSION ARM...............2-11
LUBRICANT AND REPLACEMENT PARTS,
RECOMMENDED.......................0-3
LUBRICANT CHANGE; FRONT
SUSPENSION AND AXLE................2-22
LUBRICANT CHANGE; REAR SUSPENSION
AND AXLES......................3-13,3-30
LUBRICANT, RECOMMENDED.............21-2
LUBRICANT SPECIFICATIONS, BODY........0-35
LUBRICANT SPECIFICATIONS; FRONT
SUSPENSION AND AXLE................2-20
LUBRICANT SPECIFICATIONS; REAR
SUSPENSION AND AXLES...........3-11,3-30
LUBRICANT, TRANSFER CASE.....21-273,21-294
LUBRICANT, TRANSMISSION.............21-33
LUBRICANTS, CHASSIS COMPONENT
AND WHEEL BEARING.................0-30
LUBRICANTS, CLASSIFICATION OF..........0-2
LUBRICATION, CLUTCH COMPONENT........6-1
LUBRICATION, COMPONENTS
REQUIRING NO........................0-3
LUG NUT, WHEEL......................22-11
LUGGAGE RACKÐXJ VEHICLES..........23-32
MAGNETIC CLUTCH....................24-18
MAIN BEARING FITTING CHART.......9-43,9-83
MAIN BEARINGS, CRANKSHAFT.......9-40,9-80
MAIN OIL SEALS, REAR..............9-44,9-84
MAINTENANCE, BATTERY................8B-1
MAINTENANCE, ENGINE..................0-13
MAINTENANCE SCHEDULES...............0-5
MAINTENANCE, SEVERE SERVICE...........0-5
MAJOR COMPONENT IDENTIFICATION . . . INTRO.-3
MALFUNCTION INDICATOR LAMP
(CHECK ENGINE); INSTRUMENT PANEL
AND GAUGESÐXJ................8E-2,8E-4
MALFUNCTION INDICATOR LAMP
(CHECK ENGINE); INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-16
MALFUNCTION INDICATOR LAMPÐPCM
OUTPUT............................14-26
MANIFOLDÐ2.5L ENGINE, ENGINE
EXHAUST............................11-7
MANIFOLDÐ2.5L ENGINE, INTAKE.........11-8
MANIFOLDÐ4.0L ENGINE, ENGINE
EXHAUST............................11-7
MANIFOLDÐ4.0L ENGINE, INTAKE
.........11-9
MANIFOLD ABSOLUTE PRESSURE (MAP)
SENSOR; FUEL SYSTEM
...............14-57
MANIFOLD ABSOLUTE PRESSURE (MAP)
SENSOR; IGNITION SYSTEMS
......8D-5,8D-27
MANIFOLD ABSOLUTE PRESSURE (MAP)
SENSORÐPCM INPUT
................14-21
MANIFOLD ABSOLUTE PRESSURE (MAP)
SENSOR TEST; FUEL SYSTEM
..........14-44
MANIFOLD ABSOLUTE PRESSURE (MAP)
SENSOR TEST; IGNITION SYSTEMS
......8D-14
MANIFOLD AIR TEMPERATURE SENSOR,
INTAKE
........................8D-5,8D-27
MANIFOLD AIR TEMPERATURE
SENSOR TEST, INTAKE
................8D-14
MANIFOLD ASSEMBLY, PRESSURE
GAUGE
..............................24-2
MANIFOLD, INTAKE
....................14-57
MANIFOLD LEAKAGE DIAGNOSIS, INTAKE
.....9-5
MANUAL FIRST GEAR (1) POSITION,
HYDRAULIC FLOW IN
.................21-94MANUAL SECOND (2) RANGE,
HYDRAULIC FLOW IN.................21-93
MANUAL SHIFTING TEST...............21-168
MANUAL STEERING GEAR..........19-35,19-73
MANUAL STEERING GEAR
SPECIFICATIONS.....................19-44
MANUAL STEERING GEARÐYJ VEHICLES....0-32
MANUAL STEERING SYSTEM DIAGNOSIS . . . 19-36
MANUAL TRANSMISSION................0-22
MANUAL TRANSMISSION, AX 15.........21-32
MANUAL TRANSMISSION, AX 4/5..........21-1
MANUAL TRANSMISSION, SELECTIVE
SNAP RING CHARTÐAX 15...........21-321
MANUAL TRANSMISSION, TORQUE
SPECIFICATIONSÐ AX 15.............21-320
MANUAL VALVE SHAFT OVERHAUL.......21-205
MANUAL VALVE SHAFT SEAL
REPLACEMENT.....................21-178
MARKER LAMP BULB REPLACEMENT,
SIDE...............................8L-7
MASTER CYLINDER.....................5-40
MASTER CYLINDER INSTALLATION.....5-20,5-50
MASTER CYLINDER OVERHAUL...........5-20
MASTER CYLINDER REMOVAL........5-20,5-50
MASTER CYLINDER, STANDARD...........5-20
MASTER CYLINDER/POWER BOOSTER
TEST...............................5-11
MATCH MOUNTING TIRES................22-7
MATERIAL, BRAKELINING.................5-1
MATS, CARPET/FLOOR.................23-198
MATS, CARPETS AND FLOOR...........23-129
MEASUREMENT AND ADJUSTMENT,
DIFFERENTIAL SHIM PACK..............2-42
MEASUREMENT, DIFFERENTIAL AND
PINION; FRONT SUSPENSION AND AXLE....2-38
MEASUREMENT, DIFFERENTIAL AND
PINION; REAR SUSPENSION AND AXLES....3-20
MEASUREMENT, UNIVERSAL JOINT
ANGLE..............................16-4
MEASUREMENTS AND ADJUSTMENTS,
ALIGNMENT...........................2-6
MEASURING WITH PLASTIGAGE............9-3
METALS, PAINT REPAIR ON GALVANIZED . . 23-202
METRIC SYSTEM NOTATION...........INTRO.-8
METRIC, THREAD NOTATIONÐSAE.....INTRO.-9
(MFI)ÐCOMPONENT DESCRIPTION/
SYSTEM OPERATION, MULTI-
PORT FUEL INJECTION................14-17
(MFI)ÐCOMPONENT REMOVAL/
INSTALLATION, MULTI-PORT FUEL
INJECTION..........................14-54
(MFI)ÐGENERAL DIAGNOSIS,
MULTI-PORT FUEL INJECTION..........14-32
MINI-FLOOR CONSOLEÐXJ VEHICLES....23-124
MIRROR (EXTERNAL), HALF METAL
DOOR
............................23-158
MIRROR, INTERIOR REARVIEW
...........23-74
MIRROR, LIGHTED VANITY
..............8L-19
MIRROR, REARVIEW
..................23-183
MIRROR REPLACEMENT, POWER
..........8T-4
MIRROR RETAINING BRACKET,
REARVIEW
.........................23-183
MIRROR SUPPORT BRACKET
REPLACEMENT, INTERIOR REARVIEW
....23-75
MIRROR SWITCH, POWER
................8T-2
MIRROR SWITCH REPLACEMENT,
POWER
.............................8T-4
MIRROR SWITCH TESTING, POWER
........8T-2
MIRROR TROUBLE DIAGNOSIS, LIGHTED
VANITY
............................8L-19
MIRRORS, EXTERNAL
..................23-31
MIRRORS, POWER
.....................8A-1
MISS, INJECTOR DIAGNOSISÐVEHICLE
RUNS ROUGH AND/OR HAS A
..........14-49
MODE, ABS OPERATION IN ANTILOCK
BRAKING
............................5-43
MODE, ABS OPERATION IN NORMAL
BRAKING
............................5-43
MODE, VEHICLE RESPONSE IN
ANTILOCK
............................5-3
MODEL 30 AXLE AND TUBE AXLE
(2WD)
..............................2-20
MODEL 30 FRONT AXLE
.............2-46,2-47
MODEL 35, REAR AXLE
..........3-11,3-28,3-50
14 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

STRAP, FUEL TANK SUPPORT............23-86
STRIKER AND BUMPERÐXJ VEHICLES,
REAR SEATBACK LATCH..............23-111
STRIKER, HALF-METAL DOOR LATCH.....23-175
STRIKER REPLACEMENT, HOOD LATCH....23-10
STRIKER REPLACEMENT, SAFETY LATCH . . . 23-10
STRIKER, TAILGATE LATCH.............23-161
STRIP, DOOR EDGE GUARD/EDGE
PROTECTOR........................23-61
STRIPES/DECALS, BODY..........23-25,23-153
STUD REPLACEMENT, LIFTGATE SUPPORT
ROD BALL..........................23-70
STUDS, STEERING KNUCKLE AND BALL.....2-30
STUDS, STEERING LINKAGE AND BALL.....0-30
SUN GEAR AND NO. 1 ONE-WAY
CLUTCH OVERHAUL.................21-229
SUNVISORS...................23-124,23-196
SUPPORT BRACKET, I/P TWEETER
SPEAKER/COURTESY LAMP............23-95
SUPPORT BRACKET REPLACEMENT,
INTERIOR REARVIEW MIRROR..........23-75
SUPPORT BRACKETS, CATALYTIC
CONVERTER/MUFFLER/TAILPIPE.........23-85
SUPPORT CUSHION, ENGINE FRONT.......13-15
SUPPORT OVERHAUL, OVERDRIVE.......21-216
SUPPORT OVERHAUL, OVERRUNNING
CLUTCHÐLOW-REVERSE DRUMÐ
REAR.............................21-118
SUPPORT PLATE REPLACEMENT...........5-37
SUPPORT ROD BALL STUD
REPLACEMENT, LIFTGATE..............23-70
SUPPORT ROD CYLINDER DISPOSAL,
LIFTGATE...........................23-70
SUPPORT ROD CYLINDER, LIFTGATE......23-69
SUPPORT STRAP, FUEL TANK............23-86
SUPPORTS, ENGINE (MOUNTS)............0-20
SURFACE PREPARATION...............23-201
SUSPENSION, REAR.....................3-1
SUSPENSION AND STEERING SYSTEM
DIAGNOSIS...........................2-7
SUSPENSION ARM, LOWER...............2-11
SUSPENSION ARM, UPPER...............2-11
SUSPENSION COMPONENTS, XJ FRONT.....2-47
SUSPENSION COMPONENTS, XJ REAR......3-50
SUSPENSION COMPONENTS, YJ FRONT.....2-47
SUSPENSION COMPONENTS, YJ REAR......3-50
SUSPENSION, FRONT............2-1,2-10,2-13
SUSPENSION, REAR..................2-1,3-5
SWITCHÐ2.5L ENGINE ONLY, POWER
STEERING PRESSURE.................14-58
SWITCH, ACCELERATION.................5-41
SWITCH ADJUSTMENT, BRAKELIGHT.......5-66
SWITCH AND PLUG LOCATIONS,
TRANSMISSION......................21-33
SWITCH, BRAKE.......................14-54
SWITCH, BRAKE PEDAL AND BRAKELIGHT....5-65
SWITCH CONTINUITY TESTS, IGNITION....8D-31
SWITCHÐDRIVERS DOOR POWER LOCK . . . 8P-2,
8P-3,8P-4
SWITCHÐDRIVERS DOOR POWER
WINDOW...................8S-5,8S-6,8S-7
SWITCH (HORN PAD) REPLACEMENT, HORN . 8G-3
SWITCH, IGNITION; BRAKES..............5-42
SWITCH, IGNITION; IGNITION SYSTEMS....8D-30
SWITCH INSTALLATION, BRAKELIGHT.......5-66
SWITCH INSTALLATION/ADJUSTMENT,
IGNITION...........................8D-31
SWITCH OPERATION, ACCELERATION.......5-45
SWITCH, OVERDRIVE (OVERRIDE)........14-22
SWITCH, PARK/NEUTRAL POSITION . . 8B-6,14-58,
21-173
SWITCH, PASSENGER DOOR LOCK.........8P-5
SWITCH, PASSENGER DOOR WINDOW......8S-8
SWITCHÐPCM INPUT, BRAKE............14-20
SWITCHÐPCM INPUT, EXTENDED IDLE....14-21
SWITCHÐPCM INPUT, PARK/NEUTRAL.....14-22
SWITCHÐPCM INPUT, POWER
STEERING PRESSURE.................14-22
SWITCH, POWER MIRROR................8T-2
SWITCH REMOVAL, BRAKELIGHT..........5-66
SWITCH REMOVAL, IGNITION
............8D-30
SWITCH REPLACEMENT - ALL MODELS,
TURN/HAZARD
........................8J-3
SWITCH REPLACEMENT, BLOWER
MOTOR/AIR DOOR MOTOR
.............24-39
SWITCH REPLACEMENT, FOG LAMP
.......8L-14SWITCH REPLACEMENT, HEADLAMP.......8L-4
SWITCH REPLACEMENT, HEADLAMP
DIMMER............................8L-6
SWITCH REPLACEMENT, IGNITION
KEY WARNING.......................8U-4
SWITCH REPLACEMENT, LIFTGATE WIPER . . . 8K-6
SWITCH REPLACEMENT, POWER MIRROR . . . 8T-4
SWITCH REPLACEMENT, REAR WINDOW
DEFOGGER..........................8N-4
SWITCH REPLACEMENT, REAR WIPER.....8K-13
SWITCH REPLACEMENT, SPEED CONTROL . . . 8H-9
SWITCH REPLACEMENT, WIPER CONTROL . . 8K-15
SWITCH SERVICE, PARK/NEUTRAL
POSITION.........................21-103
SWITCH TEST, EXTENDED IDLE...........14-45
SWITCH TEST, STOP LAMP SPEED
CONTROL...........................8H-7
SWITCH TESTING; POWER SEATS.........8R-2
SWITCH TESTING; POWER WINDOWS......8S-5
SWITCH TESTING; REAR WINDOW
DEFOGGER..........................8N-2
SWITCH TESTING, IGNITION.............8D-30
SWITCH TESTING, POWER MIRROR........8T-2
SWITCH TESTING, REAR WIPER/
WASHER.......................8K-7,8K-14
SWITCH TESTING, WIPER...............8K-19
SWITCH (TURN SIGNAL LEVER) TEST,
SPEED CONTROL.....................8H-7
SWITCHES, REAR DEFOGGER/FOG LAMP/
REAR WIPER........................8E-21
SWITCH/ILLUMINATION RHEOSTAT,
HEADLAMP.........................8E-21
SYMBOLS, FUSES AND ABBREVIATIONS,
WIRING............................8W-6
SYMBOLS, INTERNATIONAL VEHICLE
CONTROL AND DISPLAY............INTRO.-3
SYMBOLS, VEHICLE CONTROL AND
DISPLAY.........................INTRO.-7
SYSTEMÐAIR CONDITIONING.......24-14,24-15
SYSTEM (ABS), ANTILOCK BRAKE..........5-1
SYSTEM (ABS) INDICATOR LAMP, ANTI-
LOCK BRAKE.........................8E-2
SYSTEM CAPACITIES, COOLING...........7-38
SYSTEM CHARGE, A/C...................24-5
SYSTEM, CHIME/WARNING BUZZER........8A-1
SYSTEM CLEANING/REVERSE FLUSHING,
COOLING............................7-17
SYSTEMÐCLIMATE CONTROL.......24-22,24-37
SYSTEM COLD CRANKING TEST,
STARTING...........................8A-9
SYSTEM COMPONENTS, COOLING..........7-1
SYSTEM COMPONENTS, STEERING.........19-1
SYSTEM, COOLANT RESERVE/
OVERFLOW..........................7-19
SYSTEM COOLANT ROUTING..............7-1
SYSTEM, COOLING..................0-16,7-1
SYSTEM, CRANKCASE VENTILATION;
EMISSION CONTROL SYSTEMS..........25-5
SYSTEM, CRANKCASE VENTILATION;
LUBRICATION AND MAINTENANCE........0-17
SYSTEM DIAGNOSIS, COOLING.............7-7
SYSTEM DIAGNOSIS, AIR CONDITIONING . . . 24-12
SYSTEM DIAGNOSIS, EXHAUST............11-2
SYSTEM DIAGNOSIS, HEATING...........24-11
SYSTEM DIAGNOSIS, MANUAL
STEERING..........................19-36
SYSTEM DIAGNOSIS, POWER
STEERING...........19-3,19-4,19-5,19-6,19-7
SYSTEM DIAGNOSIS, STARTING..........8A-10
SYSTEM DIAGNOSIS, SUSPENSION AND
STEERING............................2-7
SYSTEM DIAGNOSTIC INSPECTIONS,
STARTER............................8A-9
SYSTEM DISCHARGE, A/C................24-4
SYSTEM, DRAINING COOLING.............7-16
SYSTEM ELECTRICAL TESTS, VEHICLE
SPEED CONTROL.....................8H-5
SYSTEM EVACUATION A/C................24-4
SYSTEM, EVAP (EVAPORATION)
CONTROL...........................25-4
SYSTEM, EXHAUST; INTAKE
MANIFOLD.......................0-20,11-1
SYSTEM FANS, COOLING
.................7-26
SYSTEM, FUEL
........................14-62
SYSTEM, FUEL DELIVERY
................14-2
SYSTEM HOSES, COOLING
...............7-26SYSTEM, HYDRAULIC.................21-160
SYSTEM, ILLUMINATED ENTRY...........8L-20
SYSTEM, INOPERATIVE..................8H-5
SYSTEM, LOCATING A ELECTRICAL........8W-2
SYSTEM NOTATION, METRIC..........INTRO.-8
SYSTEM OPERATION, ABS................5-39
SYSTEM OPERATION, ANTILOCK BRAKE.....5-43
SYSTEM, POWER BRAKE.................0-32
SYSTEM, POWER STEERING..............0-31
SYSTEM POWER-UP AND INITIALIZATION....5-43
SYSTEM PRESSURE RELEASE
PROCEDURE, FUEL...................14-56
SYSTEM PRESSURE TEST, FUEL......14-5,14-48
SYSTEM, REFILLING COOLING............7-17
SYSTEM RELAYS.......................5-42
SYSTEM REPAIR PROCEDURES,
THERMOMETER AND SENSOR...........8C-6
SYSTEM, SPEEDOMETER/ODOMETER;
INSTRUMENT PANEL AND GAUGESÐXJ . . . 8E-2
SYSTEM, SPEEDOMETER/ODOMETER;
INSTRUMENT PANEL AND GAUGESÐYJ . . 8E-14
SYSTEM TROUBLE DIAGNOSIS,
ILLUMINATED ENTRY............8L-21,8L-22
SYSTEM, USING ON-BOARD DIAGNOSTIC . . . 8A-19
SYSTEM, VEHICLE SPEED CONTROL........8A-1
SYSTEM WARNING LIGHTS...............5-42
SYSTEM WIRING AND ELECTRICAL
CIRCUITS, ABS........................5-4
SYSTEMÐYJ VEHICLES, HEATING........24-14
SYSTEMS, AUDIO......................8A-1
SYSTEMS DIAGNOSTICS, BATTERY/
STARTING/CHARGING..................8A-1
SYSTEMS, IGNITION....................8A-1
TABLE, BATTERY CHARGING TIME.........8A-5
TACHOMETER; INSTRUMENT PANEL
AND GAUGESÐXJ....................8E-2
TACHOMETER; INSTRUMENT PANEL
AND GAUGESÐYJ...................8E-14
TACHOMETER INOPERATIVE..............8E-3
TACHOMETERÐPCM OUTPUT............14-27
TACHOMETER REPLACEMENT........8E-5,8E-17
TAILGATE ADJUSTMENT...............23-160
TAILGATE HINGE.....................23-159
TAILGATE LATCH AND RELEASE HANDLE . . 23-160
TAILGATE LATCH STRIKER..............23-161
TAILGATE LOCK CYLINDER.............23-160
TAILGATE SERVICE....................23-159
TAILGATE SERVICE INFORMATION........23-159
TAILGATE WEATHERSTRIP SEAL.........23-161
TAILPIPE HEAT SHIELDS, MUFFLER.......13-17
TAILPIPEÐEXHAUST................11-5,11-6
TANK CAPACITIES, FUEL...........14-12,14-62
TANK FILLER TUBE CAP, FUEL....14-12,25-4,25-9
TANK FILLER TUBE, NO-LEAD FUEL.......14-12
TANK, FUEL..........................14-12
TANK PRESSURE RELIEF/ROLLOVER
VALVE, FUEL...................14-15,14-56
TANK, FUEL, SKID PLATE,
BODYCOMPONENTS.............13-16,23-84
TANK SUPPORT STRAP, FUEL............23-86
TANKS, FUEL....................14-12,14-56
TAPPETS, HYDRAULIC...............9-24,9-65
TEMPERATURE CONTROL THERMOSTAT....24-35
TEMPERATURE GAUGE, COOLANT
..........8E-1
TEMPERATURE GAUGE INOPERATIVE,
COOLANT
............................8E-3
TEMPERATURE INDICATOR INOPERATIVE,
COOLANT
............................8E-3
TEMPERATURE INDICATOR LAMP,
COOLANT
............................8E-1
TEMPERATURE SENSOR, COOLANT
........25-9
TEMPERATURE SENSOR, ENGINE
COOLANT; FUEL SYSTEM
..............14-55
TEMPERATURE SENSOR, ENGINE
COOLANT; IGNITION SYSTEMS
.....8D-4,8D-22
TEMPERATURE SENSOR, INTAKE AIR
......14-54
TEMPERATURE SENSOR, INTAKE
MANIFOLD AIR
..................8D-5,8D-27
TEMPERATURE SENSORÐPCM INPUT,
ENGINE COOLANT
....................14-21
TEMPERATURE SENSORÐPCM INPUT,
INTAKE AIR
.........................14-20
TEMPERATURE, SENSOR RESISTANCE
(OHMS)ÐCOOLANT TEMPERATURE
SENSOR/MANIFOLD
..................14-43
22 INDEXJ
Description Group-Page Description Group-Page Description Group-Page

VARIATION, DISC BRAKE ROTOR
THICKNESS..........................5-31
VEHICLE CODE DECODING............INTRO.-3
VEHICLE CODE PLATE................INTRO.-2
VEHICLE CONTROL AND DISPLAY
SYMBOLS........................INTRO.-7
VEHICLE CONTROL AND DISPLAY
SYMBOLS, INTERNATIONAL.........INTRO.-3
VEHICLE DESIGNATION CODES........INTRO.-1
VEHICLE DESIGNATIONS.............INTRO.-1
VEHICLE DIMENSION DATA....INTRO.-3,INTRO.-4
VEHICLE EMISSION CONTROL
INFORMATION (VECI) LABEL............25-1
VEHICLE, ENGINE STARTER MOTOR
TEST PROCEDURES ON................8A-9
VEHICLE, GEAR ADJUSTMENTS IN........19-37
VEHICLE, GENERATOR TEST
PROCEDURES ON....................8A-14
VEHICLE IDENTIFICATION NUMBER (VIN)
DECODING.......................INTRO.-2
VEHICLE IDENTIFICATION NUMBER (VIN)
PLATE...........................INTRO.-1
VEHICLE LOAD DATA................INTRO.-3
VEHICLE LOAD DATA, XJ.............INTRO.-5
VEHICLE RESPONSE IN ANTILOCK MODE.....5-3
VEHICLE SAFETY CERTIFICATION LABEL . INTRO.-1
VEHICLE SPEED CONTROL SYSTEM
ELECTRICAL TESTS...................8H-5
VEHICLE SPEED SENSOR................14-60
VEHICLE SPEED SENSOR TEST; FUEL
SYSTEM............................14-45
VEHICLE SPEED SENSOR TEST;
VEHICLE SPEEDCONTROL SYSTEM.......8H-5
VEHICLE SPEED SENSORÐPCM INPUT....14-23
VEHICLE VIBRATION....................22-9
VENT DOOR CONTROL CABLES...........24-39
VENT, HARD TOP ROOF................23-165
VENT WINDOW, FRONT DOOR............23-50
VENT WINDOW GLASS, FULL-METAL
DOOR............................23-177
VENT WINDOW GLASSÐXJ VEHICLES,
REAR QUARTER.....................23-80
VENTILATION, FRESH AIR...............24-39
VENTILATION SYSTEM, CRANKCASE;
EMISSIONCONTROL SYSTEMS...........25-5
VENTILATION SYSTEM, CRANKCASE;
LUBRICATIONAND MAINTENANCE........0-17
VIBRATION; FRONT SUSPENSION AND AXLE . 2-17
VIBRATION; PROPELLER SHAFTS..........16-3
VIBRATION; REAR SUSPENSION AND AXLES . . 3-8
VIBRATION DAMPER; ENGINES........9-26,9-67
VIBRATION DIAGNOSIS; WHEELS AND
TIRES.........................22-9,22-10
VIBRATION, DRIVELINE..................16-3
VIBRATION, TIRE NOISE OR..............22-4
VIBRATION TYPES......................22-9
VIBRATION, VEHICLE....................22-9
VISUAL INSPECTION...................14-32
VOLTAGE, BATTERY OPEN CIRCUIT.........8A-4
VOLTAGE DROP METHOD, STARTER
FEED CIRCUITTESTS -.................8A-9
VOLTAGE SPECIFICATIONS, OUTPUT.......8B-12
VOLTAGE TEST, BATTERY OPEN CIRCUIT....8A-3
VOLTAGEÐPCM INPUT, BATTERY.........14-19
VOLTMETER...........................8E-1
VOLTMETER INOPERATIVE................8E-3
VOLTMETER, OPERATIONAL CHECK.......8A-15
WARNING INOPERATIVE, LOW FUEL........8E-4
WARNING LAMP, LOW FUEL..............8E-2
WARNING LIGHT DISPLAY, ABS............5-3
WARNING LIGHT DISPLAY, BRAKE..........5-4
WARNING LIGHTS, BRAKE.................5-1
WARNING SWITCH REPLACEMENT,
IGNITION KEY........................8U-4
WASHER, DIAGNOSING INTERMITTENT
WINDSHIELD........................8K-12
WASHER, DIAGNOSING NON-
INTERMITTENTWINDSHIELD............8K-12
WASHER, DIAGNOSING REAR WIPER.......8K-6
WASHER INDICATOR INOPERATIVE, LOW....8E-4
WASHER (INTERMITTENT), DIAGNOSING
WINDSHIELD
.........................8K-4
WASHER, INTERMITTENT WIPER
.........8K-20
WASHER (NON-INTERMITTENT),
DIAGNOSINGWINDSHIELD
..............8K-4
WASHER NOZZLE REPLACEMENT
.........8K-13WASHER PUMP REPLACEMENT . . 8K-2 8K-6,8K-11
WASHER PUMP REPLACEMENT, REAR.....8K-13
WASHER PUMP REPLACEMENTÐRIGHT
HAND DRIVE.........................8K-3
WASHER, STANDARD WIPER............8K-19
WASHERS, WINDSHIELD WIPERS..........8A-1
WASHER/THRUST PLATE SPECIFICATIONS,
30RH/32RH SNAP RING/THRUST.......21-322
WATER LEAK DETECTION AND REPAIR,
FIXEDGLASS..................23-83,23-189
WATER PUMPS.....................7-9,7-10
WATER PUMP TESTS.....................7-9
WATERDAM, FULL-METAL DOOR.........23-176
WEAR COMPENSATION, CALIPER
OPERATION..........................5-24
WEAR INDICATORS, TREAD...............22-3
WEAR PATTERNS, TIRE..................22-4
WEATHERSTRIP SEAL, COWL...........23-139
WEATHERSTRIP SEAL, LIFTGATE
OPENING...........................23-70
WEATHERSTRIP SEAL REPLACEMENT,
LIFTGATEGLASS....................23-163
WEATHERSTRIP SEAL, TAILGATE........23-161
WEATHERSTRIP SEAL, WINDSHIELD
FRAME............................23-185
WEATHERSTRIP SEAL/CROSSMEMBER
AIRDEFLECTOR, COWL................23-10
WEATHERSTRIP SEALS, DOOR WINDOW
GLASSAND DOOR OPENING............23-62
WEATHERSTRIP SEALS, FULL-METAL
DOOR............................23-180
WHEEL ALIGNMENT, FRONT...............2-5
WHEEL BALANCE, TIRE..................22-6
WHEEL BEARING LUBRICANTS, CHASSIS
COMPONENT.........................0-30
WHEEL BEARINGS, FRONT...............0-31
WHEEL BRAKE COMPONENTS..............5-1
WHEEL CYLINDER INSTALLATION..........5-37
WHEEL CYLINDER OVERHAUL.............5-36
WHEEL CYLINDER REMOVAL.............5-36
WHEEL INSTALLATION...................22-6
WHEEL LUG NUT......................22-11
WHEEL NUT TIGHTENING............5-32,5-37
WHEEL ORNAMENTATION................22-6
WHEEL REPLACEMENT..................22-6
WHEEL RUNOUT, TIRE...................22-8
WHEEL SENSOR AIR GAP ADJUSTMENT....5-49
WHEEL SENSOR INSTALLATION, FRONT.....5-49
WHEEL SENSOR INSTALLATION, REAR......5-50
WHEEL SENSOR REMOVAL, FRONT........5-49
WHEEL SENSOR REMOVAL, REAR.........5-49
WHEEL SPEED SENSOR OPERATION........5-45
WHEEL SPEED SENSORS.................5-41
WHEEL, STEERING.....................19-45
WHEEL/TIRE SIZE AND INPUT SIGNALS......5-3
WHEELHOUSE FLARES AND LINERS, REAR . 23-18
WHEELHOUSE SPLASH LINERS..........23-146
WHEELHOUSE TRIM PANELSÐXJ
VEHICLES,QUARTER.................23-115
WHEELS..............................22-6
WINDOW APPLIQUEÐXJ VEHICLES,
QUARTER..........................23-29
WINDOW DEFOGGER GRID REPAIR, REAR . . . 8N-2
WINDOW DEFOGGER GRID TEST, REAR.....8N-1
WINDOW DEFOGGER, REAR..............8A-1
WINDOW DEFOGGER SWITCH
REPLACEMENT, REAR..................8N-4
WINDOW EXTERIOR MOULDINGS, DOOR . . . 23-61
WINDOW, FRONT DOOR VENT
............23-50
WINDOW GLASS AND DOOR OPENING
WEATHERSTRIP SEALS, DOOR
..........23-62
WINDOW GLASS, FIXED
..........23-73,23-183
WINDOW GLASS, FRONT DOOR
..........23-49
WINDOW GLASS, FULL-METAL DOOR
.....23-178
WINDOW GLASS, FULL-METAL DOOR
VENT
.............................23-177
WINDOW GLASS, HARD TOP QUARTER
. . . 23-188
WINDOW GLASS, REAR DOOR
...........23-52
WINDOW GLASS, REAR DOOR FIXED
......23-53
WINDOW GLASS REGULATOR, FRONT
DOOR
.............................23-48
WINDOW GLASS REGULATOR, FULL-
METAL DOOR
......................23-177
WINDOW GLASS REGULATOR HANDLE,
FULL-METALDOOR
..................23-175WINDOW GLASS REGULATOR, REAR
DOOR
.............................23-51
WINDOW GLASSÐXJ VEHICLES,
LIFTGATE
...........................23-81
WINDOW GLASSÐXJ VEHICLES,
REAR QUARTERVENT
.................23-80
WINDOW GLASS/REAR QUARTER
PLASTIC INSERTÐXJ VEHICLES,
QUARTER
..........................23-80
WINDOW REGULATOR REPLACEMENT
.......8S-9
WINDOW SWITCH, PASSENGER DOOR
......8S-8
WINDOW SWITCH
..............8S-5,8S-6,8S-7
WINDSHIELD FRAME
..................23-184
WINDSHIELD FRAME WEATHERSTRIP
SEAL
.............................23-185
WINDSHIELD GLASS
..................23-185
WINDSHIELD GLASS REPLACEMENT
......23-75
WINDSHIELD REVEAL MOULDING
. . . 23-73,23-183
WINDSHIELD SERVICE INFORMATION
......23-75
WINDSHIELD SIDE MOULDINGÐXJ
VEHICLES
.........................23-114
WINDSHIELD WASHER, DIAGNOSING
INTERMITTENT
......................8K-12
WINDSHIELD WASHER,
DIAGNOSINGNON-INTERMITTENT
.......8K-12
WINDSHIELD WASHER (INTERMITTENT),
DIAGNOSING
.........................8K-4
WINDSHIELD WASHER (NON-
INTERMITTENT),DIAGNOSING
............8K-4
WINDSHIELD WIPER MOTOR
.............8K-2
WINDSHIELD WIPERS, DIAGNOSING
. . 8K-3,8K-11
WIPER ARM AND PIVOT ASSEMBLY
REPLACEMENT,FRONT
.................8K-9
WIPER ARM REPLACEMENT, FRONT
........8K-8
WIPER ARM REPLACEMENT, REAR
........8K-12
WIPER BLADE REPLACEMENT, FRONT
......8K-8
WIPER CONTROL SWITCH REPLACEMENT
. . . 8K-15
WIPER, DIAGNOSING REAR
...............8K-6
WIPER, LIFTGATE
.......................8K-5
WIPER MODULE, INTERMITTENT
..........8K-5
WIPER MOTOR, FRONT
.................8K-10
WIPER MOTOR REPLACEMENT, REAR
.....8K-13
WIPER MOTOR, WINDSHIELD
.............8K-2
WIPER SWITCH REPLACEMENT,
LIFTGATE
............................8K-6
WIPER SWITCH REPLACEMENT,
REAR
..............................8K-13
WIPER SWITCH TESTING
...............8K-19
WIPER SWITCHES, REAR DEFOGGER/
FOGLAMP/REAR
.....................8E-21
WIPER WASHER, DIAGNOSING REAR
.......8K-6
WIPER WASHER, INTERMITTENT
.........8K-20
WIPER WASHER, STANDARD
............8K-19
WIPERS, DIAGNOSING WINDSHIELD
. . 8K-3,8K-11
WIPERS/WASHERS, FRONT
...............8K-1
WIPERS/WASHERS GENERAL INFORMATION,
FRONT
..............................8K-8
WIPER/WASHER, DIAGNOSING REAR
......8K-14
WIPER/WASHER SWITCH TESTING,
REAR
..........................8K-7,8K-14
WIRE CODE IDENTIFICATION
.............8W-2
WIRING AND COMPONENT IDENTIFICATION
. 8W-13
WIRING AND ELECTRICAL CIRCUITS,
ABS SYSTEM
..........................5-4
WIRING DIAGRAM SHEETS AND INDEXES
. . . 8W-1
WIRING DIAGRAMS YJ
.................8W-73
WIRING PROBLEMS, TROUBLESHOOTING
. . . 8W-3
WIRING REPAIR
.......................8W-4
WIRING, SECONDARY IGNITION
...........8W-1
WOODGRAIN MOULDING
................23-19
WOODGRAIN OVERLAY
.................23-22
WORM SHAFT REPLACEMENT, RACK
PISTON
............................19-30
WORN THREADS, REPAIR DAMAGED OR
.....9-4
JINDEX25
Description Group-Page Description Group-Page Description Group-Page