1994 JAGUAR XJ6 ECU

Automatic Transmission (V12 & AJ16 Supercharged)
8.2.11 'A' SHIFT SOLENOID, RENEW
(4,Ol SC AND 6,OL)
SRO 44.15.45
Open the hood and fit a suitable fender cover.
Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
Remove the fluid pan, see Sub-section 8.2.14 (4,OL SC) or
= Disconnect the internal harness plug from the 'A' Shift
. Release and remove the 'A' Shift solenoid to valve body
. Remove the solenoid from the valve body (Fig. 1).
= Remove and discard the '0' ring seal from the valve body.
. Place the solenoid aside.
. Fit a new '0 ring seal to a new 'A' Shift solenoid.
. Lubricate the '0' ring seal.
Fit the solenoid to the valve body using a twisting motion.
. Fit and tighten the solenoid to the valve body using a new
. Connect the internal harness plug to the solenoid.
. Refit the fluid pan, see Sub-section 8.2.14 (4,OL SC) or
. Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Sub-section
Remove the fender cover and close the hood.
tion
8.2.13.
Sub
-section 8.2.15 (6,OL).
solenoid.
securing screw.
securing screw.
Sub
-section 8.2.15 (6,OL).
8.2.13.
Fin. 1
Issue 1 August 1994 12 X300 VSM

Pomrtrain Automatic Transmission (V12 & AJ16 Supercharged)
8.2.12 '6' SHIFT SOLENOID, RENEW
(4,OL SC AND 6,OL)
SRO 44.15.46
Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
. Remove the fluid pan, see Subsection 8.2.14 (4,OL SC) or
. Disconnect the internal harness plug from the 'B' Shift
. Release and remove the 'B' Shift solenoid to valve body
. Remove the solenoid from the valve body (Fig. 1).
. Remove and discard the '0' ring seal from the solenoid.
= Place the solenoid aside.
. Fit a new '0' ring seal to a new 'B' Shift solenoid.
. Lubricate the '0' ring seal.
. Fit the solenoid to thevalve body using a twisting motion.
. Fit and tighten the solenoid to the valve body using a new
. Connect the internal harness plug to the solenoid.
. Refit the fluid pan, see Subsection 8.2.14 (4,OL SC) or
Lower the vehicle on the ramp.
Refill the transmission unit with fluid, see Subsection
8.2.13.
= Remove the fender cover and close the hood.
tion
8.2.13.
Subsection 8.2.15
(6,OL).
solenoid.
securing screw.
securing screw.
Sub
-section 8.2.15 (6,OL).
Fig. 1
X300 VSM 13 Issue 1 August 1994

Pomrtrain Automatic Transmission (V12 & AJ16 Supercharged)
8.2.14 FLUID PAN, RENEW (4,OL SC)
SRO 44.24.04
. Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sukec-
. Slacken the downpipe catalyst to intermediate catalyst
Slacken the intermediate catalyst to intermediate si-
9 Disconnect the intermediate catalyst pipe from the down-
. Clean the downpipe and intermediate pipe joint.
. Release and remove the fluid pan securing bolts.
Remove the fluid pan (1 Fig. 1)) and gasket (2 Fig. 1).
. Drain the residual fluid from the fluid pan.
Remove the fluid pan gasket.
. Clean the fluid pan gasket, which can be re-used if in good
Place the fluid pan gasket aside.
= Remove the magnet (3 Fig. 1) from the fluid pan.
= Clean the magnet and place on a clean surface.
. Clean the transmission fluid pan joint face.
. Clean the fluid pan.
Place the fluid pan aside.
. Attach the magnet to the recess in a new fluid pan.
. Fit and align a serviceable gasket to the fluid pan.
. Fit the fluid pan and gasket to the transmission unit.
. Fit and tighten the fluid pan securing bolts.
. Apply sealant to the intermediate pipe joint. See Service
Materials in the preliminary pages, this Section.
Reconnect the intermediate pipe to the downpipe.
Align the intermediate catalyst assembly.
. Tighten the intermediate pipe to the downpipe securing
. Align the intermediate silencers to the intermediate cata-
. Tighten the intermediate silencer securing clamps.
. Lower the vehicle on the ramp.
Refill the transmission unit with fluid, see Subsection
8.2.13.
. Remove the fender cover and close the hood.
tion 8.2.13.
clamp securing bolts.
lencers clamp securing bolts.
pipe.
condition.
clamp. lyst assembly.
.. rli
i
1
JLL-713
Fig. 1
X300 VSM 15 Issue 1 August 1994

Automatic Transmission (V12 & AJ16 Supercharged) Powertrain
8.2.15 FlUlD PAN, RENEW (6,Ol)
SRO 44.24.04
Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
. Slacken the underfloor catalyst to downpipe clamps se-
. Displace and reposition the olive clamps on the pipes.
. Slacken the underfloor catalyst to intermediate silencer
Displace the underfloor catalyst assembly rearwards to
. Displace and remove the olives from the downpipes.
. Using a wire brush, clean the olives and downpipe joints.
m Place a suitable piece of wood between the underfloor
Drain the transmission lubrication system, see Sub-sec-
Release and remove the fluid pan securing bolts.
Drain the residual fluid from the fluid pan.
. Remove the fluid pan (1 Fig. 1) and gasket (2 Fig. 1).
. Clean the fluid pan gasket, which can be re-used if in good
. Place the fluid pan gasket aside.
. Remove the magnet (3 Fig. 1) from the fluid pan.
. Clean the magnet and place on a clean surface.
. Clean the transmission fluid pan joint face.
. Clean the fluid pan.
. Place the fluid pan aside.
. Attach the magnet to the recess in a new fluid pan.
. Fit and align a serviceable gasket to the fluid pan.
. Fit the fluid pan and gasket to the transmission unit.
. Fit and tighten the fluid pan securing bolts.
. Remove the block of wood from between the underfloor
catalyst and the floor.
. Apply sealant to the downpipe joints and olives. See Ser- vice Materials in the preliminary pages, this Section.
Fit and seat the olives to the downpipes.
Reconnect the underfloor catalyst to the downpipes.
. Reposition the olive clamps.
. Tighten the underfloor catalyst to downpipe clamps secur-
. Align the intermediate silencers to the underfloor catalyst
. Tighten the clamp securing bolts.
Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Sub-section
curing
bolts.
clamps securing bolts.
disconnect from the downpipes.
catalyst and the body for access.
tion 8.2.13.
condition.
ing bolts.
assembly.
8.2.13. Remove the fender cover and close the hood.
JLL-719
Fin. 1 ~
Issue 1 August 1994 X300 VSM 16

Powertrain Automatic Transmission (V12 & AJ16 Supercharged)
8.2.16 FLUID PAN GASKET, RENEW (4,OL SC)
SRO 44.24.05
Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
Drain the transmission lubrication system, see Sub-sec-
. Slacken the downpipe catalyst to intermediate catalyst
. Slacken the intermediate catalyst to intermediate si-
. Disconnect the intermediate catalyst pipe from the down-
Clean the downpipe and intermediate pipe joint.
. Release and remove the fluid pan securing bolts.
. Remove the fluid pan (1 Fig. 1) and gasket (2 Fig. 1).
. Drain the residual fluid from the fluid pan.
. Remove and discard the fluid pan gasket.
Remove the magnet (3 Fig. 1) from the fluid pan; clean the
. Place the magnet on a clean surface.
. Clean the transmission fluid pan joint face.
. Clean the fluid pan.
. Place the fluid pan aside.
. Attach the magnet to the recess in a new fluid pan.
. Fit and align a new gasket to the fluid pan.
. Fit the fluid pan and gasket to the transmission unit.
. Fit and tighten the fluid pan securing bolts.
. Apply sealant to the intermediate pipe joint. See Service
Materials in the preliminary pages, this Section.
. Reconnect the intermediate pipe to the downpipe.
. Align the intermediate catalyst assembly.
. Tighten the intermediate pipe to downpipe securing
. Align the intermediate silencers to the intermediate cata-
. lighten the intermediate silencer securing clamps.
. Lower the vehicle on the ramp.
tion 8.2.13.
clamp securing bolts.
lencers clamp securing bolts.
pipe.
magnet.
clamp. lyst assembly.
. Refill the transmission unit with fluid, see Subsection
8.2.13.
. Remove the fender cover and close the hood.
1
JLL-713
Fia. 1
X300 VSM 17 Issue 1 August 1994

Automatic Transmission (V12 & AJ16 Supercharged) Powertrain
8.2.17 FLUID PAN GASKET RENEW (6,OL)
SRO 44.24.05
Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
. Slacken the underfloor catalyst to downpipe clamp secur-
. Displace and reposition the olive clamps on the pipes.
. Slacken the underfloor catalyst to intermediate silencer
. Displace the underfloor catalyst assembly rearwards to
ing
bolts.
clamps securing bolts.
disconnect from the downpipes.
Displace and remove the olives from the downpipes.
Using a wire brush, clean the olives and downpipe joints.
. Place a suitable piece of wood between the underfloor
Drain the transmission lubrication system, see Sub-sec-
Release and remove the fluid pan securing bolts.
. Remove the fluid pan (1 Fig. 1) and gasket (2 Fig. 1).
Drain the residual fluid from the fluid pan.
Remove and discard the fluid pan gasket.
Remove the magnet (3 Fig. 1) from the fluid pan; clean the
magnet.
Place the magnet on a clean surface.
Clean the fluid pan joint face.
Clean the fluid pan.
. Place the fluid pan aside.
. Attach the magnet to the recess in the fluid pan.
. Fit and align a new gasket to the fluid pan.
. Fit the fluid pan and gasket to the transmission unit.
. Fit and tighten the fluid pan securing bolts.
. Remove the block of wood from between the under floor
catalyst and the floor.
9 Apply sealant to the downpipe joints and olives. See Ser- vice Materials in the preliminary pages, this Section.
= Fit and seat the olives to the downpipes.
. Reconnect the underfloor catalyst to the downpipes.
. Reposition the olive clamps.
. lighten the underfloor catalystto downpipe clamps secur-
Align the intermediate silencers to the underfloor catalyst
. Tighten the clamp securing bolts.
. Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Sub-section 8.2.13.
Remove the fender cover and close the hood.
catalyst
and the body for access.
tion
8.2.13.
ing bolts.
assembly.
2
1
JLL.7K
Fig. 1
0
0
0
0
Issue 1 August 1994 18 X300 VSM

Automatic Transmission (V12 & AJ16 Supercharged) Powertrain
8.2.19 TRANSMISSION INTERNAL HARNESS MULTI-
PIN SOCKET '0' RING, RENEW
(4,OL SC AND 6,011
SRO 44.24.20
9 Open the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
. Drain the transmission lubrication system, see Sub-sec-
. Remove the fluid pan, see Sub-section 8.2.14 (4,OL SC) or
. Disconnect the external harness multi-pin plug from the
Note: The plug is secured to the socket by its captive lock- ing ring.
= Release and remove the internal harness multi-pin socket
. Displace the internal harness multi-pin socket from the
Remove and discard the '0 ring seal (Fig.1) from the
. Fit and seat a new '0' ring seal to the multi-pin socket.
. Reposition and seat the internal harness multi-pin socket
to the transmission casing.
. Fit and tighten the internal harness multi-pin socket to the
transmission casing securing nut.
Connect the external harness multi-pin plug to the inter- nal harness multi-pin socket; the plug is secured by its
captive locking ring.
Refit the fluid pan, see Sub-section 8.2.14 (4,OL SC) or Sub-section 8.2.15 (6,OL).
. Lower the vehicle on the ramp.
. Refill the transmission unit with fluid, see Sub-section
8.2.13.
. Remove the fender cover and close the hood.
tion
8.2.13.
Sub
-section 8.2.15 (6,OL).
internal harness multi-pin socket.
to transmission casing securing nut.
transmission casing.
multi
-pin socket.
0
0
0
0
X300 VSM Issue 1 August 1994 20

Pamrtrain Automatic Transmission (V12 & AJl6 Supercharged)
8.2.20
SRO 44.24.21 INTERNAL
L UBRICATION PIPE, RENEW
(4,OL SC AND 6,011
. Open
the hood and fit a suitable fender cover.
. Raise the vehicle on a ramp.
Drain the transmission lubrication system, see
Sub-sec- tion 8.2.13.
. Remove the fluid pan, see Subsection 8.2.14 (4,OL SC) or Sub-section 8.2.15 (6,OL).
Release and remove the internal lubrication pipe retainer to valve body securing bolt.
. Remove the lubrication pipe retainer.
. Release and remove the lubrication pipe clamp to valve
. Remove the lubrication pipe clamp.
. Displace and remove the lubrication pipe from the trans-
. Drain any residualfluidfromthe lubrication pipe and place
. Clean the relevant parts.
0 Fitandfullyseata newlubricationpipetothetransmission
body securing nut.
mission unit.
the pipe aside.
unit.
. Fit the lubrication pipe clamp.
. Fit and tighten the lubrication pipeclamptovalve bodyse-
. Fit the lubrication pipe retainer.
. Refit the fluid pan, see Sub-section 8.2.14 (4,OL SC) or
. Lower the vehicle on the ramp.
Refill the transmission unit with fluid, see Sub-section
8.2.13.
9 Remove the fender cover and close the hood.
curing
bolt.
Subsection
8.2.15 (6,OL).
X300 VSM Issue 1 August 1994