1994 JAGUAR XJ6 engine

Introduction
FOREWORD
This Vehicle Service Manual (VSM) is Dart
-
of a
set of service literature which covers -. diagnosis and rectification of problems associated with all areas of the X300 family of vehicles.
It is designed to be read in conjunction with other manuals, namely the various Unit Service Manuals (USM) (as
applicable to the particular vehicle under diagnosis/ repair) and the X300 Electrical Diagnostic Manual (EDM); see list
below.
It should be noted that its scope is limited to those areas that are unique to the family, e.g. Remove & Refit procedures
for Body Components, Engine, Transmission etcetera, Fuel, Emissions & Engine Management systems, and so on.
Fault Diagnosis and repair procedures (together
with Technical Data, Recommended Lubricants, Capacities etcetera) for major assemblies such as engines, automatic and manual transmissions, are covered in the separate Unit Service
Manuals.
The Unit Service Manuals are notvehicle
-specific, but are designed to be read in conjunction with this VSM, and, where so equipped, with other Jaguar Vehicle Service Manuals for new models launched subsequent to the X300 family.
The X300 Electrical Diagnostic Manual is the final part of the 'set' of service documentation. This manual
is
family-specific, and is designed to aid theTechnician to isolate electrical faults and to correct them. It covers all aspects
of electrical fault diagnosis, including:
OBD
II Codes and emission control system related fault diagnosis / rectification.
Circuit Diagrams
Component (Relays, fuse boxes, control modules etcetera) Location
/ Harness Diagrams I Ground Locations
Connector Locations.
Service Manuals Required
The Manuals required to service the X300 family of vehicles are as follows:
X300 Vehicle Service Manual
X300 Electrical Diagnostic Manual
Unit Service Manuals:
AJ16 Engine Service Manual
VI2 Engine Service Manual ZF AutomaticTransmissions Service Manual (ZF supplies transmissions for 3.2 liter and 4.0 liter normally aspirated
versions) Powertrain Automatic Transmissions Service Manual (The Powertrain name succeeds that of Hydra
-Matic.
Powertrain are suppliers of the 4L 80 E transmission as fitted to 4.0 litre supercharged and 6.0 litre versions)
Each
of the X3Okpecific manuals is divided into Sections which adopt the same title and number where relevant, i.e. Section 5.1 of both the VSM and the EDM cover Fuel, Emission Control & Engine Management System (AJ16). An
over
-all contents list showing each section title and number together with its page-edge locator is given in this section
and in the introduction to the EDM.
The VSM (not applicable to the EDM) also contains Appendices which cover specialized areas such as the current
vehicle specification, routine maintenance schedule etc. These are carried at the rear of this Manual, and have their
own contents page within this section.
INDEX
rapid location of information. The entries are set out as per the following example: @ This manual carries a comprehensive index at the rear, which is designed to save the Technician time by permitting
CLIMATE CONTROL SYSTEMS. Section 14.
See also Electrical Diagnostic Manual
Clutch
Description: Sect. 7.7 - 10
Fault diagnosis: Sect 7.1 - 11
In the example the heading in upper case lettering is to a section title, and it refers to the section number, 14, and also to the EDM as electrical diagnostic information will be found in that manual's section 14. The entry for clutch tells us that the relevant description will be found on page 10 of Section 7.1 of this manual, and
that fault diagnosis procedures start on page 11. In this case there is no reference to the EDM as electrical diagnosis does not apply to this area.
GLOSSARY OF TERMS
This Section contains a Glossary of general and emissions-related terminology (commencing on page 5).
X300 VSM 1 Issue 1 August 1994

e-
@
Contents
Fuel, Emission Control & Engine Management (AJI 6)
Manual Transmission & Clutch (AJl6)
Driveshafts & Final Drive
Suspension Systems
Body Components & Trim
Climate Control Systems
Issue 1 August 1994 3 x300
- - ~~

GLOSSARY OF TERMS
Introduction
This glossary of terms is intended to cover both general and emissions-related (to SAE J 1930) terminology. It is in- tended to enable the user to ascertain the meaning of standardized terms and acronyms used throughout the Manual.
The required term may be looked-up in the left-hand column, and subsequent columns give the standard abbreviation
or acronym, definitions and previously used terms, as applicable.
As this Manual is a world
-wide publication, and must comply with certain Society of Automotive Engineers Standards, it has been necessary to adopt the terminology etc. demanded by that Standard.
Term(s) Abbreviation Definition Previously used
(if applicable) term(s) (or Eng- lish Eauivalent)
A
throttle pedal
accelerator Dedal AP
AI= measurement across the spanner flats of a
across flats
nut or bolt head
adaptor
AC.
aircon
adapter
after bottom dead center
after
too dead center event
occurring after BDC
event occurring after TDC
ABDC
ATDC ACL
AIC
ACS
Air
Cleaner
Air Conditioning
Air Conditioning Signal air conditioning
compressor clutch
operation is signalled to the PCM which
induces idle speed corrections to
compensate for engine load changes
module controlling air conditioning, heating
and ventilation
wing or similar, designed to obtain some
effect from the flow of air over
it
electrical current whose flow alternates in
direction, in a sinusoidal waveform
NCCM Air Conditioning Control Module
airfoil aerofoil
alternating current ac
aluminium
aluminum
Ambient temperature Temperature
of the air surrounding an object
SI unit of current AmDere A Amp Amp. hour -~ 1 Ampere flowing for one hour
system, usually ele&o&ally controlled (but ~- __. .. . Ampere hour
Anti
-Lock Braking System Ah
ABS can be mechanically) which prevents wheel
lock
-up under braking by sensing lack of
rotation of a wheel(s) and diverting fluid
pressure away from
it (them). Originally Anti-Blockier System (Bosch).
ABS control module
ABS
/ traction control control
module ABS
CM
ABS I TC CM
aerial
antenna (plural, antennae or
antennas)
analog
Analoa Volt-Ohm meter analogue
AVOM unit of pressure
(1.01325 bar)
atmospheres
automatic transmission atm
auto,
auto gearbox
drive shaft
axle shaft shaft
transmitting power to the rear wheel
hubs
.-
Issue 1 August 1994 X300 VSM 7

Terrn(s1 Abbreviation Definition Previously used (if applicable) term(s) (or Eng- lish Eauivalentl
5
Babbitt metal
backlight
back
-up lamp
balk ring
t
battery positive Voltage B+
Barometric Absolute Pressure BARO
Sensor
base Idle
base timing
battery
before bottom dead center BBDC
before top dead center BTDC
blower BLR
Body Processor Module BPM
British Standards BS
I British Standards Automotive BSAu
brake horsepower
brake mean effective pressure BMEP
brake
ontoff BOO
brake rotor
I bottom dead center BDC
bypass air BPA
bumper guard
I
bushing I
rotating component of manual transmission
which prevents premature engagement of
gears
The positive Voltage from
a battery or any
circuit connected directly to it.
sensor measuring the pressure of
surrounding air at any given temperature
and altitude
Idle
rpm determined by the throttle lever
being hard
-set on the throttle body with the
IAC solenoid disconnected
Spark advance in degrees before top dead
center of the base engine without any control
from the PCM
Electrical storage device producing DC
Voltage by means of electrochemical
reaction
event occurring before BDC
event (usually ignition) occurring before TDC
Device which supplies a current of air at
moderate pressure, e.g. heater or
AJC blower
Control module for body electrical systems,
e.g. interior lamps, windshield wash wipe
control etc..
standard specification issued by the British
Standards Institution
effective horsepower developed by an
engine or motor, as measured by a brake
applied to its output shaft
that part of the effective pressure developed
in a cylinder that would result in a cylinder
output equal to the bhp of the engine
indicates the position of the brake pedal
process of bedding
-in the internal working
surfaces of e.g. an engine by avoiding excess
build
-up of heat
lowest point of piston travel in a
reciprocating engine
mechanical control of throttle bypass air
cylindrical plain bearing white
metal
backlight,
rear screen reversing lamp
baulk ring
B+,
+ve, VSS
BARO, APS
CCM (Central
Control Module).
CPU
brake disc
running
-in
overrider bush
Issue 1 August 1994 8 X300 VSM

Introduction i
Term(s) Abbreviation Definition
(if applicable)
GLOSSARY OF TERMS
Previously used term(s) (or Eng-
lish Equivalent)
indicates camshaft position
device designed to hold dry material, e.g.
evaporative emission canister
controls purging of the EVAP canister
colorless gas with a density of approximately
1.5 times that of air
poisonous gas produced as the result of
incomplete combustion
camshaft
I
CID
sensor,
Hall sensor
Camshaft
Position
Camshaft Position Sensor CMPS
canister
Canister Purge CANP
Carbon Dioxide
CO2
I Case Ground I CSEGND
Carbon
Monoxide
camber
CO
Canadian Motor Vehicle Safety
Standard
caster
Catalytic Converter
Celsius
center
I
CMVSS
C
centimeters
I cm
trail built in to the geometry of a steered
roadwheel to give
it a caster - self-steering -
effect
caster,castor
color
columnlmirror control module I C/M CM
charge current
Closed Loop
Closed Loop System
Clutch
clutch disc, clutch disk
clutch
throwout bearing
connecting rod bearing
CL
CLS
a shaft on which phased cams are mounted.
Usually used to regulate opening and closing
of engine cylinder head valves
current developed by the generator
control system with one or more feedback
loops
device which uses mechanical, magnetic or
friction type connections to facilitate
engaging or disengaging
two shafts or
rotating members charging
current
Control
module casing ground
inclination of the plane of a wheel to the
vertical plane
ofthe vehicle. May be negative
or positive.
Also convex curvature across road surface
bearing (usually split, plain) at the lower end
of the connecting rod where
it connects with
the crankshaft big
end bearing
in
-line exhaust
system device used to reduce
the level of engine exhaust emissions
SI term forthe Centigradescale, with freezing Doint at zero and boilina Doint at looo
I centre
I centimetres
friction disc of a clutch assembly clutch
plate,
centre plate,
diaphragm spring to release the clutch disc
I colour
Issue 1 August 1994 X300 VSM 9

Introduction
.OSSARY OF TERMS
Term(s)
Crankshaft Position
Crankshaft Position Sensor
Crankshaft Position
liming Ring
Crankcase Ventilation System
cubic centimeters
curb weight
4 Control
CKP
CKPS
CKPTR
cv
cm3
Control Module
P
T Abbreviation (if applicable)
CM
cylinder sleeve, sleeve
I I
Definition
a means or device to direct and regulate a process or guide the operation of a machine,
apparatus or system
a self-contained group of
electrical/electronic components, designed
as a single replaceable unit, and controlling
one or more processes as above
flexible, usually fabric, roof of an open
(convertible) vehicle
shaft, carrying pinions, running parallel to
the mainshaft in
a transmission unit
split pin which is used as
a locking device for
a castellated nut, etc.
generates crankshaft position information in
conjunction with the CKPTR (also generates
speed information in certain applications)
toothed ring which triggers the CKPS
system which scavenges camshaft cover and
crankcase emissions and feeds them into the
inlet manifold.
weight of vehicle with fuel, lubricants and
coolant, but excluding driver, passengers or
payload
thin
-walled, hard metal cylinder inserted into
the cylinder block of an engine, and in which
the piston runs
Previously used
term(s) (or Eng.
lish Eauivalent)
hood,
convertible hood
layshaft
split pin,
cotter pin
cubic
centimetres kerb weight
cylinder liner ~ ~~
Issue 1 August 1994 10 X300 VSM

Introduction
Term(s) Abbreviation Definition
(if applicable) Previously
used term(s) (or Eng-
lish Equivalent)
downshift
draft _.
drivability
driveshaft
driveshaft tunnel
dry sleeve
Dual Overhead Cam
Data
Data Link Connector
Data Output Line
defogger, backlight defogger
degree (angle or temperature)
Department of Transportation
(US)
Department of Transport (UK)
Deutsche lnstitut fur
Normuna
diameter
Diagnostic Module
Diagnostic Test Mode
Diagnostic Trouble Code
differential housing
differentia
I pressure
Differential Pressure Feedback
EGR
dimmer switch DOHC
DLC
DOL
deg, O
DOT
DTP DIN dia
DM
DTM
DTC
DPFE longitudinal
shaft transmitting power from
transmission output to rear axle differential
tunnel
in floor above the driveshaft (propeller
shaft)
cylinder sleeve which is not in contact with
coolant
engine configuration with two camshafts
positioned above the valves
(US) Fact or group of facts.
connector providing access
andlor control of
the vehicle information, operating
conditions, and diagnostic information
circuit that sends certain information from
the PCM to the instrument cluster
German Standards regulation body
Supplemental Restraint System
(non-controlling) module for diagnostics
overview
a level of capability in an OBD system. May
include different functional states
to observe
signals, a base level to read
DTCs, a monitor
level which includes information on signal
levels,
bi-directional control with onloff board aids, and the ability to interface with
remote diagnosis
an
alphahumeric identifier for a fault
condition identified by the On
-Board
Diagnostic
(OBD) system
rotating housing
(in a bevel differential)
attached to the crownwheel, carrying the
final drive pinions
pressure difference between two regions e.g.
between intake manifold and atmospheric
pressures
an EGR system that monitors differential
EGR pressure across a remote orifice
to control EGR flow change
down
draught
driveability
propeller shaft
transmission
tunnel
dry liner
(English) Group
of facts (i.e. plural
of
datum)
HRW, rear screen
heater, demister
Self Test Mode
Self Test Code.
Fuel Fail code
differential cage
dip switch,
dipper switch
Issue 1 August 1994 11 X300 VSM

Introduction c
GLOSSARY OF TERMS
Term(s) Abbreviation Definition Previously used (if applicable) term(s) (or Eng- lish Equivalent)
0
EGRT Sensor
EGR Vacuum Regulator
1 Read-only memory
I Electronic Engine Control
kronic Secondary Air Injection
Engine Control Module
Engine Coolant Level
ECT Sensor
Engine Speed
Engine Speed Sensor
1 Evaporative Emission Control
Va Ive
Exhaust Gas Recirculation
Solenoid Vacuum Valve
Exhaust Gas Recirculation
Temperature Sensor
Exhaust Gas Recirculation Valve
Extreme Pressure EGR
EGRT EVR
EVP
EDM
EEPROM EPROM EEC
EAlR
ECM ECL
ECT
ECTS
RPM
EPA
EVAP
EVAPP EGRS
EGRT Sensor
EGRV EP System
which reduces
NOx emissions by
adding exhaust gases to the incoming
fuel/air charae
Sensing EGR function based on temperature
change.
controls EGR flow by changing vacuum to
the EGR valve
an EGR system that directly monitors EGR
valve position to control EGR flow
Manual which deals with the diagnosis of
electrical faults (see also Vehicle Service
Manual and Unit Service Manual)
a system that provides electronic control of
enaine electronics
a pump
-driven system for providing
secondarv air usina an electric air Dump
thermistor which provides engine coolant
temperature signal to the PCME to trigger
enrichment circuits which increase injector
'on' time for cold start and warm-up
sensor fitted on flywheel of
VI2 engine;
provides engine speed information
system designed to prevent fuel vapor from
escaping into the atmosphere. Typically
includes a charcoal filled canister to absorb
fuel
vaoor
additives to drive axle lubricants. Designed
to protect the spiral bevel gears from wear
induced by their
slidingholling action EGR
EEPROM,
EPPROM
EPROM ECU
engine coolant level indicator
Coolant temp.
sensor, ECT
revlmin. RPM
purge valve
EGR solenoid
valve
EGR temperature
sensor
X300 VSM issue 1 August 1994 13