Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
Diesel
engines
Glow plug system
The
engine is
fitted
with
a glow plug
sys
tem.
The required glow plug warm-up time
is
indicated by a lamp which is controlled by
the coolant temperature - see page 49.
Cold
starting
aid
To
assist cold starting, there is a device (cold starting aid)
fitted
in the injection
pump.
The
cold starting aid is actuated when the knob on the
left
of the steering column is
fully
pulled out.
Starting
a cold
engine
• At ambient temperatures down to -15
degrees
C, pull the cold start knob our
fully
before operating the starter.
At lower temperatures, the knob should not
be
pulled out
until
engine
is
firing
reg
ularly
- the engine will then start more
readily.
• Turn the key in the ignition lock to
posi
tion 2 (see page 36) - the glow plug warning lamp comes on. It goes out when the igni
tion temperature is reached (see page 49).
While
the
glow
plugs are
working
do not
switch
on any
other
heavy
cur
rent
consumers because
this
would
place an unnecessary load on the
battery.
• When the warning lamp goes out, start the engine immediately.
Do
not depress the accelerator while start
ing.
If the engine only fires irregularly, continue
to operate the starter a few seconds longer (30 seconds at maximum) until the engine runs under its own power.
If the engine does not start, switch the glow
plugs on again and try starting it again as de
scribed.
If the engine still does not start the
fuse for the glow plugs may have blown -
page123.
•
Push
the cold start aid knob in fully as
soon
as the engine has reached its normal
operating temperature.
Starting
a
warm
engine
The
glow plug lamp does not come on - the engine can be started straight away. Do not pull the cold start aid knob and do not press
the accelerator pedal.
38
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
Instruments
The arrangement of the instruments de pends on the model concerned and the en
gine fitted. 70 - 126
1-
Speedometer 40
2-
Coolant temperature 41
3- Digital clock* 41 or multi-function indicator* 42
4-
Fuel gauge 46 5- Rev counter* 46 or analog clock 46 1 - Speedometer
During the running-in period the instruc
tions on page 76 should be noted.
Mileage recorder
The upper counter registers the total dis
tance driven and the lower one the short
trips.
The last figure of the lower counter
indi
cates 100 m or Vio mile.
The trip recorder can be set back to zero by pressing the knob in the speedometer
dial.
40
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
2
-
Coolant temperature
—
~~s
gauge starts
to
work
when ignition
is
=
.vitched on,
but it
takes some time before
~e needle reaches
its
final position.
-en ignition
is
switched
on the
warning
c~ip flashes
for a few
seconds
as a
func-
•
:nal check.
5
- Cold
-. Did
high
engine speeds and
do not
work
r-gine
too
hard
yet.
:
- Normal
nen
the
vehicle
is
driven normally
the
~eedle
should settle
down
in
this zone.
-en engine
is
working hard and the ambi-
r~t
temperature
is
high,
the
needle
may
-ove
a
long
way up. This is not serious as long as the
warning lamp does not flash.
Warning lamp
If
the lamp flashes when driving, check first
the indicated coolant temperature.
If the
needle
is in the
normal zone,
top the
coolant
up at the
next
opportunity.
If
the reading
is
in the upper zone, either the
coolant level
is too low or the
coolant tem
perature
is too
high.
Stop,
switch
en
gine off
and
try to
find cause
of
trouble
-
see
page 47.
Notes
•
Additional
lights
in
front
of the cooling air intake interfere
with
the
flow
of cooling air. At
high
ambient
temperatures and
full
throttle
there is a danger that the engine
will
then
overheat.
3
-
Digital clock
*
To
set the
time there
are two
buttons
on
lower left
of
instrument cluster.
The
hours
are
set
with
the
upper button
(h) and the
minutes
with
the
lower one
(min):
•
If
pressed briefly, preferably
with
a ball
pen,
the time changes one hour
or
one min
ute.
•
If
pressed continuously the hours
or
min
utes
change continuously.
With
the minute button the clock can be set exactly
to the
second:
•
Press button until time shown
by
clock
is
one minute before time
to be set.
•
Press button
at the
moment when
the
seconds
indicator
of an
accurate clock
shows a full minute
or
when the time signal
is
heard
on the
radio.
41
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS AND EQUIPMENT
call up the data the memories are se-
r ::ed by means of the switch A in the wiper
- Single journey memory
'- - Total journey memory
_~e
"allowing data can be obtained from the ~ r~iories:
• Driving time • -verage fuel consumption
• Distance driven
• -verage speed
E-asing the
memories
:~ the ignition switched on, both mem-
: es can be erased separately in each
: :ch position by pressing switch A : --sed the appropriate detent position to 0
::; tion for longer than one
second.
" :~.e battery is disconnected for any rea-
::" the stored information is automatically
Ksed.
The displays
When
the ignition is switched on
"MF11"
or
"MFI 2" appears in the display according to
which memory is switched on.
No symbol -
Time
The
time is shown even when the ignition is switched off.
The
time can be set
with
the buttons (h and min) on the lower
left
of instrument cluster
- see "Digital
Clock"
page 41.
—'— -
Driving
time
In
switch
position 1 the driving time
which has elapsed since ignition was
switched on or the memory cancelled is indicated - see previous page also "Single
journey memory".
In
switch
position 2 the total driving
time for all individual journeys is indicated -
see
previous page also "Total journey mem
ory".
The
maximum time in both switch positions
is
99 hours 59 minutes. When this figure is
exceeded
the indication starts at zero again. MPG
(1/100
km) -
Average
fuel
consumption
The
average consumption is indicated not
the actual consumption at the time of read
ing.
The
average fuel consumption is indicated,
after switching on the ignition or erasing the memory being
used,
after a distance of
about 100 metres. Up to this point a dash
appears
instead of a figure. When vehicle is moving the indicated value is up-dated
every 5
seconds.
In
switch
position 1 the average
con
sumption for the single journey is indicated.
In
switch
position 2 the average
con
sumption indicated is
that
obtained during
all
single journeys - see "Total journey memory" on previous page
also.
Note
The
amount of fuel used is not indicated.
43
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND EQUIPMENT
4
-
Fuel gauge
^u
This gauge works
when
ignition
is
switched on
but it
takes some time for
the
needle
to
reach
its
final
position.
The tank holds about
80
litres.
When
the needle reaches the start of the
re
serve
zone
(arrow)
there is about 10 litres
(2
gallons)
of
fuel left
in the
tank. 5
-
Analog clock
To
set the
time press
the
button
on
lower
right
in
combi instrument:
•
If
pressed briefly, preferably with
a
ball
pen,
the
time
is
advanced
one
minute.
•
If
pressed continuously the minute hand goes faster and
at
the same time
the
hours
are
set as
well.
With
the button the clock can
be set
exactly to
the
second:
•
Press
button until time is one minute be fore time
to be set.
•
Press
button
at the
moment
when
the
seconds indicator
of an
accurate clock
shows
a
full
minute or
when
the time signal is heard
on the
radio. 5
-
Rev counter
*
The
rev
counter needle must not move into
the
red
zone
of the
scale
on any
account.
The additional
red
dotted zone before
the
red zone
on the
scale which some models
have
shows
the
maximum engine speed
permitted
briefly
e.g.
when
overtaking
when
engine
has
been run in and
is
warm
-
see page
76
also.
It is
advisable
to
change up
or
reduce engine speed
at the
latest
by
the time
the
needle reaches this
zone..
rijp
Changing
up in good time helps
<-^>
to
save
fuel and keeps the noise
down.
Change down
to
the next lower gear before
the engine
no
longer runs smoothly.
The green or green shaded area on the scale shows the speed
at
which
the
engine
is de
veloping
its
most favourable torque
and is
working
most economically. Drive
as
often as possible with needle
in
this area.
During
the
running-in
period,
high engine
revs
should
be
avoided.
46
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND
EQUIPMENT
Warning
lamps
~ne layout of the warning lamps depends on
:ne model and the engine fitted. The sym-
: ols shown here are also on the actual warn-ng lamps.
|- Coolant temperature/ coolant level 47
1- Engine oil pressure 47
I- High beams 48
-- Turn signals 48
5-
Brake system 48
V Alternator 49
" Glow plugs 49 Coolant
temperature/
Coolant level1'
This
lamp flashes for a few seconds as a
functional check when ignition is switched
on.
If the lamp does not go out afterwards or
flashes
when driving, either the coolant
temperature is too high orthe coolant level1'
too low:
Stop,
switch
engine
off and check
level.
Add coolant if necessary.
11 Only on vehicles
with
automatic coolant level monitor(see page 102).
Attention
• Be
careful
when
opening the
coolant
expansion
tank!
When
the
engine
is hot the cooling
sys
tem is
under
pressure -
Danger
of scalding!
Therefore
let
engine
cool
down
before
unscrewing
the cap.
• Do not
touch
the fan. The fan can
switch
on suddenly -
even
when
ignition
is
switched
off.
For
further details see pages 102 and 103.
If the coolant level is in order the trouble
may be due to failure of the radiator fan.
Check
radiator fan fuse and renew if
necessary-seepage
122.
If the warning lamp does not go out al
though coolant level and fan fuse are in order, do not
drive
on - call in expert as
sistance.
If the trouble is only caused by the fan and
assuming
coolant level is in order and tem perature warning lamp is out - one can drive
on to the nearest Volkswagen dealer. In
order to make good use of the air stream for
cooling,
do not let engine idle or drive very
slowly.
2 - Engine oil pressure -7
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND EQUIPMENT
The
warning lamp flashes when ignition is
switched
on. the lamp must go out when
engine
has started.
If the warning lamp does not go out or
flashes
when driving - a buzzer also sounds
at engine speeds above 2000 rpm - stop,
switch
engine
off, check oil level and if
necessary,
add oil - see page 97.
If the lamp comes on although the oil level
is
in order, do not
drive
on. Do not even
run the engine at idling speed-call in expert
assistance.
Note
The oil pressure
warning
lamp
is not an oil
level
indicator.
The oil
level
should
therefore
be checked at reg
ular
intervals,
preferably
every
time
the
fuel
tank
is filled.
3 -
High
beams 10 4 - Turn signals
The
warning lampflashes when
turn
signals
are
switched on. If a
turn
signal fails, the
warning lamp flashes twice as fast. (Not
when towing a trailer).
Further
details are given on pages 49
and
52. 5 -
Brake
system «^
The
warning lamp comes on when
• the handbrake is on
• the brake fluid level is too low
The
ignition must be switched on.
Attention
If the
lamp
does not go out
when
handbrake
is released or comes
on
when
driving, the
fluid
level
in
the reservoir is too low. If an in crease in
pedal
free
travel
is no
ticed
at the same
time,
one of the
brake
circuits may
have
failed.
You can
drive
on
carefully
to the
nearest
Volkswagen
dealer
but
allow
for
higher
pedal
pressures and longer
braking
distances on
the way.
The
warning lamp comes on when high
beams
are on or when the headlight flasher
is
used.
48
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans
Downloaded from www.Manualslib.com manuals search engine
CONTROLS
AND
EQUIPMENT
6-Alternator
Q
~ne warning lamp comes on when the
igni-
I
on
is
switched on and must go out when
She
engine
is
started.
i the warning lamp comes on when driving,
stop,
switch
engine
off
and
check
the
alternator V-belt.
f the V-belt
is
broken or loose do not
drive
on with
a
vehicle which
has a 4 cylinder
engine
because the coolant pump
is
then
no
longer being driven. The V-belt must
be
tensioned
or
renewed.
ehicles with
a 5
cylinder engine
can
nor
mally
be
driven to the nearest Volkswagen
dealer when
the
V-belt
is
broken
or
loose oecause
the
coolant pump
is
driven separ
ately but then the battery will discharge
con
tinuously
and all
non-essential electrical consumers should
be
switched
off.
f the warning lamp comes on although
the
belt
is
not broken, one can normally drive on
to
the nearest Volkswagen dealer (all engine
types)
but the
battery will then discharge
continuously
- see
previous paragraph.
7-Glow
plugs
W
(Diesel engines only)
When
the engine
is cold
the warning lamp comes on when key
is
turned to Drive
posi
tion
(ignition on).
If
the warning lamp does not come
on,
there
is
a
defect in the glow plug system
-
call
in
expert assistance.
When
the
lamp goes out,
start
the engine
immediately
-
see page
38.
When
the
engine
is warm the
glow plug
lamp
does
not
come on -the engine can
be
started straight
away.
(®)
-
Anti-locking
Brake
System
(ABS)*
The operational readiness
of the
essential electrical components
of the ABS are
checked,
both before moving off and when
driving,
by an electronic monitoring system.
The warning lamp lights up when
the
igni
tion
is
switched on and
it
must go out again, at the latest, after the engine
has
started.
If
the warning lamp does not go out
or if it
comes on when driving the system
is
not
in
order.
The
vehicle can then only
be
braked
with
the
normal system
-
that
is
without
ABS-.The vehicle must be taken to a Volks
wagen Dealership
as
soon
as
possible.
Further details on ABS
is
given on page
30.
<]1i>
-
Trailer
turn
signals
The warning lamp
*
flashes when turn
sig
nals are switched on when towing
a
trailer.
If a
turn signal fails on the trailer or vehicle,
the warning lamp does not flash.
www.vwT4camper.info - a useful website for owners and enthusiasts of VW T4 Transporter Campervans