1991 MITSUBISHI MONTERO water pump
[x] Cancel search: water pumpPage 12 of 1333
Fig. 8: Aligning Timing Marks (SOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc.
Inspection (Montero & Pickup)
Inspect timing belt for wear on edges of drive teeth. Inspect
belt for oil contamination, cracks, separation, worn or missing teeth
and hardened back surface. Replace belt if worn, damaged or
contaminated. Inspect belt tensioner for smooth rotation. Replace if
defective.
Installation (Montero & Pickup)
1) Install rear timing belt cover. Tighten bolts to
specification. See TORQUE SPECIFICATIONS (MONTERO & PICKUP) table at
end of article. Install camshaft sprockets (if removed). Using holder,\
hold camshaft and tighten retaining bolt to specification.
2) Install belt tensioner and spring. Ensure spring is
secured on pin of water pump and engaged in hole of belt tensioner
with hook of spring pointing from cylinder block.
3) Rotate belt tensioner counterclockwise as much as
possible, and temporarily tighten bolt. Align all timing marks with
No. 1 cylinder at TDC of compression stroke. See Fig. 8.
4) Install timing belt on crankshaft sprocket and then left
camshaft sprocket with all slack removed from tension side of belt.
Route timing belt onto water pump pulley, right camshaft sprocket and
tensioner. Remove any slack from belt by rotating left and then right
camshaft sprockets counterclockwise.
5) Ensure belt is installed in original direction of rotation
and all timing marks are aligned. Install flange on crankshaft. Loosen
belt tensioner bolts slightly, and allow tensioner to apply belt
tension.
6) Using Crankshaft Socket (MD998716), rotate crankshaft 2
Page 15 of 1333
Inspect belt tensioner for smooth rotation. Replace if defective.
Installation
1) Install rear timing belt cover. Tighten bolts to
specification. See TORQUE SPECIFICATIONS (3000GT) table at end of
article. Install camshaft sprockets (if removed). Using holder, hold
camshaft and tighten camshaft sprocket bolt to specification.
2) Install belt tensioner and spring. Ensure spring is
secured on pin of water pump and engaged in hole of belt tensioner
with hook of spring pointing from cylinder block.
3) Rotate belt tensioner counterclockwise as much as
possible, and temporarily tighten bolt. Align all timing marks with
No. 1 cylinder at TDC of compression stroke. See Fig. 8.
4) Install timing belt on crankshaft sprocket, rear cylinder
bank camshaft sprocket, water pump pulley, front cylinder bank
camshaft sprocket and timing belt tensioner. Ensure belt is installed
in original direction of rotation and all timing marks are aligned.
Install flange on crankshaft. Loosen belt tensioner bolts slightly,
and allow tensioner to apply belt tension.
5) Using Crankshaft Socket (MD998716), rotate crankshaft 2
revolutions clockwise. DO NOT rotate counterclockwise. Realign all
timing marks. Tighten belt tensioner bolts to specification. See
TORQUE SPECIFICATIONS (3000GT) table. Using belt tension gauge,
measure belt tension halfway between crankshaft sprocket and camshaft
sprocket on side opposite belt tensioner.
6) Belt tension should be 46.3-63.3 lbs. (21-29 kg). To
install remaining components, reverse removal procedure. Install
proper length bolts in timing belt covers and engine support bracket.
See Figs. 9 and 10. Tighten bolts to specification. See TORQUE
SPECIFICATIONS (3000GT) table.
NOTE: Engine support bracket reamer bolt must be tightened slowly
while spraying lubricant on bolt.
Fig. 11: Identifying Timing Belt Cover Bolt Length (SOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc.
Removal (DOHC)
1) Remove lower splash shields. Remove cruise control
Page 25 of 1333
and No. 2. Install bearing caps with front mark arrow facing the same
direction as similar mark on cylinder head beside bearing journal.
Note bearing cap number and identification mark ("I" for intake
camshaft and "E" for exhaust). See Fig. 22.
3) Install front and rear bearing caps. Tighten bearing cap
bolts to specification. See TORQUE SPECIFICATIONS (3000GT) table at
end of article. Coat camshaft oil seal area with oil. Using Seal
Installer (MD998761), install camshaft oil seal. Using Circular
Packing Installer (MD998761), install circular packing.
4) Install crankshaft angle sensor adapter. To complete
installation, reverse removal procedure. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
REAR CRANKSHAFT OIL SEAL
Removal
Remove transaxle/transmission. See appropriate article in
TRANSMISSION SERVICING or CLUTCHES. Remove flywheel or drive plate.
Remove rear oil seal case. Pry seal from seal case.
Installation
To install, coat seal lip with oil. Using Seal Installer
(MD998718), install seal in seal case. Apply sealant to sealing
surface of seal case. Install seal case. Install flywheel or drive
plate. Tighten bolts to specification. See appropriate TORQUE
SPECIFICATIONS table at end of article. To complete installation,
reverse removal procedure.
WATER PUMP
Removal
Drain cooling system. Remove timing belt and crankshaft
sprocket. See TIMING BELT under REMOVAL & INSTALLATION. Remove coolant
pipes to water pump (if required). Remove water pump bolts, noting
length and location for reassembly reference. Remove water pump.
Installation
To install, reverse removal procedure using new gasket and
"O" rings. Coat all "O" rings with water before installation. Install
water pump and gasket. Tighten bolts to specification. See appropriate
TORQUE SPECIFICATIONS table at end of article.
OIL PAN
Removal (Montero)
1) Remove hood. Remove skid plate and lower covers. Raise and
support vehicle. Disconnect and remove exhaust pipe from exhaust
manifolds. Drain engine oil. Remove starter cover and starter. Remove
oil pressure sending unit connector. Remove front suspension
crossmember.
2) Remove transmission stays. Remove ground cable and motor
mount heat shields. Attach engine hoist. Remove motor mount bolts.
Raise engine, and insert a 1" wood spacer between front insulator and
mounts. Lower engine onto wood blocks.
3) Raise vehicle using a hoist. Remove oil pan bolts. Using
Seal Cutter (MD998727), separate oil pan from cylinder block. Remove
pan from vehicle.
Removal (Pickup)
1) Remove skid plate and lower covers. Raise and support
vehicle. Drain engine oil. Using Steering Linkage Puller (C-3894-A or
MB990635), disconnect relay rod from idler arm and steering box.
2) Remove oil pan bolts. Using Seal Cutter (MD998727),
Page 34 of 1333
Main Bearing Cap Bolt ...................... 55-61 (75-83)
Oil Pick-Up Tube Bolt ...................... 11-15 (15-20)
Rear Engine Support
Bracket-To-Engine Bolt .................... 13-18 (18-25)
Relief Valve Plug .......................... 29-36 (39-49)
Right Engine Support Bracket Bolt
10x22 mm ................................. 25-36 (34-49)
12x22 mm & 12x32 mm ...................... 47-61 (64-83)
Rocker Shaft ............................... 14-15 (19-20)
Timing Belt Tensioner Bolt ................. 16-21 (22-29)
Water Pump Bolt ............................ 14-20 (19-27)
INCH Lbs. (N.m)
Delivery Pipe Bolt ......................... 84-108 (9-12)
Distributor Adapter Bolt .................. 108-132 (12-15)
Oil Filter Bracket Bolt .................. 108-120 (12-14)
Oil Pan Bolt ................................. 48-60 (5-7)
Oil Pump Cover Bolt ........................ 72-108 (8-12)
Oil Pump Mounting Bolt ................... 108-120 (12-14)
Rear Seal Case Bolt ........................ 84-108 (9-12)
Rocker Cover Bolt ............................ 72-84 (8-9)
Throttle Body Bolt ......................... 84-108 (9-12)
Timing Belt Cover Bolt ..................... 84-108 (9-12)
Transmission Mounting Plate Bolt ........... 84-108 (9-12)
( 1) - Tighten in 2 steps using proper sequence.
See Fig. 4.
\
\
\
\
\
\
TORQUE SPECIFICATIONS TABLE (3000GT) \
\
\
\
\
\
Application Ft. Lbs. (N.m)
Air Intake Plenum Stay Bolts ..................... 13 (18)
Automatic Tensioner Bolt ......................... 17 (23)
Camshaft Bearing Cap Bolt ........................ 15 (20)
Camshaft Sprocket Bolt ........................... 65 (88)
Connecting Rod Nut ............................... 38 (52)
Crankshaft Pulley Bolt
SOHC ................................. 108-116 (146-157)
DOHC ................................. 130-137 (176-186)
Cylinder Head Bolt ( 1)
SOHC ................................... 76-83 (103-113)
DOHC
Non-Turbo ............................. 76-83 (103-113)
Turbo ................................. 87-94 (118-127)
Distributor Adapter Bolt ......................... 11 (15)
Drive Plate Bolt ................................. 55 (75)
Engine Support Bracket Bolt
Except 10x40 mm ........................ 76-83 (103-113)
10x40 mm ................................. 47-54 (63-73)
Exhaust Manifold Nut ............................. 13 (18)
Flywheel Bolt .................................... 55 (75)
Intake Manifold Bolt
Lower Manifold
Non-Turbo ............................... 11-15 (15-20)
Turbo .................................... 9-11 (12-15)
Upper Manifold ................................. 13 (18)
Main Bearing Cap Bolt ............................ 58 (79)
Oil Filter Bracket Bolt .......................... 11 (15)
Oil Pick-Up Tube Bolt ............................ 14 (19)
Oil Pump Mounting Bolt ........................... 11 (15)
Page 35 of 1333
Rear Engine Support
Bracket-To-Engine Bolt .................... 13-18 (18-25)
Relief Valve Plug ................................ 33 (45)
Rocker Shaft ............................... 14-15 (19-20)
Roll Stopper Bracket Through Bolts ......... 36-43 (49-58)
Turbocharger-To-Exhaust Fitting ............ 40-47 (54-64)
Timing Belt Tensioner Bolt ....................... 31 (42)
Water Pump Bolt .................................. 17 (23)
INCH Lbs. (N.m)
Delivery Pipe Bolt .............................. 108 (12)
Oil Pan Bolt ................................. 48-60 (5-7)
Oil Pump Cover Bolt .............................. 96 (11)
Rear Seal Case Bolt .............................. 96 (11)
Rocker Cover Bolt
SOHC ....................................... 72-84 (8-9)
DOHC ............................................ 26 (3)
Throttle Body Bolt ......................... 84-108 (9-12)
Timing Belt Cover Bolt ..................... 84-108 (9-12)
Transmission Mounting Plate Bolt ........... 84-108 (9-12)
( 1) - Tighten in 2 steps using proper sequence.
See Fig. 4.
\
\
\
\
\
\
ENGINE SPECIFICATIONS
GENERAL ENGINE SPECIFICATIONS
GENERAL SPECIFICATIONS TABLE \
\
\
\
\
\
Application Specification
3.0L V6 DOHC Non-Turbo
Displacement ....................... 181.4 Cu. In. (3.0L)
Bore ................................... 3.587" (91.1 mm)
Stroke ................................. 2.992" (76.0 mm)
Compression Ratio ................................ 10.0:1
Fuel System ......................................... PFI
Horsepower @ RPM ............................. 222 @ 6000
Torque Ft. Lbs. @ RPM ........................ 201 @ 4500
3.0L V6 DOHC Turbo
Displacement ....................... 181.4 Cu. In. (3.0L)
Bore ................................... 3.587" (91.1 mm)
Stroke ................................. 2.992" (76.0 mm)
Compression Ratio ................................. 8.0:1
Fuel System ......................................... PFI
Horsepower @ RPM ............................. 300 @ 6000
Torque Ft. Lbs. @ RPM ........................ 307 @ 2500
3.0L V6 SOHC
Displacement ....................... 181.4 Cu. In. (3.0L)
Bore ................................... 3.587" (91.1 mm)
Stroke ................................. 2.992" (76.0 mm)
Compression Ratio ................................. 8.9:1
Fuel System ......................................... PFI
Horsepower @ RPM ............................. 143 @ 5000
Torque Ft. Lbs. @ RPM ........................ 168 @ 2500
\
\
\
\
\
\
Page 95 of 1333
HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
Page 131 of 1333
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performance ............ .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Connection damaged ...... B .. Require repair or replacement.
Contaminated, affecting
performance ............ A ............ Require replacement.
Corroded internally ..... 1 ............ Suggest replacement.
Dessicant bag
deteriorated ........... A ........ (1) Require replacement.
Further inspection required.
Dessicant at the end of
its useful life
(saturated
with moisture) ......... 1 .. Suggest repair or replacement.
Filter screen torn ...... A .. Require replacement of screen.
Fitting damaged ......... B .. Require repair or replacement.
Fusible plug leaking .... A .... Require replacement of plug.
Inoperative ............. A ........... ( 2) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Pressure relief device
leaking ................ A . Require replacement of pressure
relief device.
Restricted .............. A .. Require repair or replacement.
Sight glass no longer
transparent ............ 2 ... Suggest replacement of drier.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Tubing connection
leaking ................ A .. Require repair or replacement.
( 1) - Inspect system to determine effects of dessicant bag
deterioration.
( 2) - Inoperative includes intermittent operation or out of
OEM specification.
\
\
\
\
\
\
\
WATER PUMPS (ELECTRIC AUXILIARY)
WATER PUMP (ELECTRIC AUXILIARY) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Page 476 of 1333
SUPER CHARGERS
SWITCHES
THERMAL VACUUM VALVES
THERMOSTATIC AIR DOOR ASSEMBLIES
THERMOSTATS AND HOUSINGS
THROTTLE BODIES
THROTTLE CABLES
THROTTLE LINKAGES AND CABLES
THROTTLE POSITION SENSORS
THROTTLE POSITION SWITCHES
TIMING BELT SPROCKETS
TIMING BELTS
TORQUE STRUTS
TRANSMISSION RANGE SWITCHES
TUBE CLAMPS
TUBE CONNECTORS
TUBE COUPLERS
TUBES
TURBO CHARGERS
VACUUM CONNECTIONS
VACUUM HOSES, TUBES AND CONNECTIONS (NON-METALLIC)
VACUUM REGULATOR SOLENOIDS
VACUUM TUBES
VEHICLE SPEED SENSORS
VOLUME AIR FLOW SENSORS
WASTE GATE CONTROL SOLENOIDS
WASTE GATES AND BOOST CONTROL MECHANISMS
WATER PUMPS (ELECTRIC)
WATER PUMPS (NON-ELECTRIC)
WIRING HARNESSES AND CONNECTORS
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication