1991 MITSUBISHI MONTERO manual transmission
[x] Cancel search: manual transmissionPage 222 of 1333
CO M PU TE R R ELE A R N P R O CED URES
1991 M it s u bis h i M onte ro
GENERAL INFORMATION
Computer Relearn Procedures
All Models
* PLEASE READ THIS FIRST *
The following general procedures are to be used if
driveability problems are encountered after power loss or battery has
been disconnected. These procedures may provide an aid in eliminating
these problems.
To reduce the possibility of complaints, after any service
which requires battery power to be disconnected, vehicle should be
road tested.
COMPUTER RELEARN PROCEDURES
Vehicles equipped with engine or transmission computers may
require a relearn procedure after vehicle battery is disconnected.
Many vehicle computers memorize and store vehicle operation patterns
for optimum driveability and performance. When vehicle battery is
disconnected, this memory is lost. The computer will use default data
until new data from each key start is stored. As computer memorizes
vehicle operation for each new key start, driveability is restored.
Vehicle computers may memorize vehicles operation patterns for 40 of
more key starts.
Customers often complain of driveability problems during
relearn stage because vehicle acts differently then before being
serviced. Depending on type and make of vehicle and how it is
equipped, the following complaints (driveability problems) may exist:
* Harsh Or Poor Shift Quality
* Rough Or Unstable Idle
* Hesitation Or Stumble
* Rich Or Lean Running
* Poor Fuel Mileage
These symptoms and complaints should disappear after a number
of drive cycles have been memorized. To reduce the possibility of
complaints, after any service which requires battery power to be
disconnected, vehicle should be road tested. If a specific relearn
procedure is not available, the following procedure may be used:
Automatic Transmission
* Set parking brake, start engine in "P" or "N" position.
Warm-up vehicle to normal operating temperature or until
cooling fan cycles.
* Allow vehicle to idle for one minute in "N" position. Select
"D" and allow engine to idle for one minute.
* Accelerate at normal throttle position (20-50%) until vehicle
shifts into top gear.
* Cruise at light to medium throttle.
* Decelerate to a stop, allowing vehicle to downshift, and use
brakes normally.
* Process may be repeated as necessary.
Manual Transmission
Page 224 of 1333
CO OLIN G S YSTE M S PEC IF IC ATIO NS
1991 M it s u bis h i M onte ro
1991 ENGINE COOLING
Mitsubishi Cooling System Specifications
Mitsubishi: Eclipse, Galant, Mirage,
Montero, Pickup, Precis, 3000GT
COOLING SYSTEM SPECIFICATIONS
COOLING SYSTEM SPECIFICATIONS TABLE \
\
\
\
\
\
\
Application Specification
Coolant Replacement Interval ............. 30,000 Miles or 24 Months
Coolant Capacity
(Includes Heater & Reserve Tank)
Eclipse
1.8L .......................................... 6.6 qts. (6.2L)\
2.0L .......................................... 7.6 qts. (7.2L)\
Galant .......................................... 7.6 qts. (7.2L)\
Montero ........................................ 10.0 qts. (9.5L)\
Pickup
2WD
Automatic Transmission ....................... 6.4 qts. (6.1L)\
Manual Transmission .......................... 6.3 qts. (6.0L)\
4WD ........................................... 8.9 qts. (8.4L)\
Precis .......................................... 5.6 qts. (5.3L)\
3000GT .......................................... 8.8 qts. (8.3L)\
Pressure Cap ............................................. 11-15 psi
Thermostat Opens
Except 3000GT
Starts ............................................. 190
F (88C)
Fully Open ........................................ 212F (100C)
3000GT
Starts ............................................. 170
F (77C)
Fully Open ......................................... 190F (88C) \
\
\
\
\
\
\
Page 289 of 1333
\003
* D RIV ETR AIN S YSTE M S U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 991 M it s u bis h i M onte ro
GENERAL INFORMATION
Drivetrain/Transmission Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Drive/Power Train Assemblies
AUTOMATIC TRANSMISSION/TRANSAXLE ASSEMBLIES
DIFFERENTIAL AND FINAL DRIVE ASSEMBLIES
MANUAL TRANSMISSION/TRANSAXLE ASSEMBLIES
TRANSFER CASE ASSEMBLIES
Drive/Power Train Components
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AXLES
BEARINGS AND RACES
BELL CRANKS
BELL HOUSINGS
BUSHINGS (EXTERNAL)
CABLES (SPEEDOMETER)
CABLES (TV, DETENT AND SHIFT)
CARRIER BEARINGS
CLUTCH CABLES AND CABLE HOUSINGS
CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH FORKS
CLUTCH LINKAGES (MECHANICAL)
CLUTCH MASTER CYLINDERS
CLUTCH PEDALS
CLUTCH PIVOTS
CLUTCH PRESSURE PLATES
CLUTCH RELEASE BEARINGS
CLUTCH SLAVE CYLINDERS (CONCENTRIC)
CLUTCH SLAVE CYLINDERS (CONVENTIONAL OR EXTERNAL)
COMPANION FLANGES
CONNECTORS
COOLER BYPASS VALVES
COOLER LINES
COOLERS
CV JOINTS
DIP STICK TUBES
DIP STICKS (FLUID LEVEL INDICATORS)
DOWEL PINS, GUIDES AND PILOT HOLES
DRIVE SHAFT FLANGES
DRIVE SHAFTS AND HALF SHAFTS
DUST BOOTS
ENGINE MOUNTS
EXCITER RINGS
FILLER TUBES
FILTERS AND SCREENS
Page 294 of 1333
NOTE: Whenever transmission or drivetrain service is performed
that affects the suspension alignment, for example,
removing the engine cradle, it is required that the
alignment be checked and corrected if necessary.
AUTOMATIC TRANSMISSION/TRANSAXLE ASSEMBLIES
AUTOMATIC TRANSMISSION/TRANSAXLE ASSEMBLY INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Any internal component
failure that requires
removal of the assembly
from the vehicle for
service. ( 1) ........... A ........... ( 2) Require repair or
replacement of the automatic
transmission/transaxle
assembly.
( 1) - It is Required that the torque converter and all other
failure related components be inspected for cause and
condition.
( 2) - For components not requiring removal of the assembly,
refer to the component listing in this document.
\
\
\
\
\
\
\
DIFFERENTIAL AND FINAL DRIVE ASSEMBLIES
NOTE: Does not include half shafts.
DIFFERENTIAL AND FINAL DRIVE ASSEMBLY INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Any internal component
failure that requires
removal of the assembly
from the vehicle for
service. ( 1) ........... A ... Require repair or replacement
of the differential assembly.
( 1) - For components not requiring removal of the assembly,
refer to the component listing in this document.
\
\
\
\
\
\
\
MANUAL TRANSMISSION/TRANSAXLE ASSEMBLIES
MANUAL TRANSMISSION/TRANSAXLE ASSEMBLY INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Any internal component
failure that requires
removal of the assembly
from the vehicle for
service. ( 1) ........... A ... Require repair or replacement
of the manual
transmission/transaxle
assembly.
( 1) - For components not requiring removal of the assembly,
Page 302 of 1333
![MITSUBISHI MONTERO 1991 Service Manual CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\](/manual-img/19/57332/w960_57332-301.png "MITSUBISHI MONTERO 1991 Service Manual CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\")
CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH DISC (MANUAL TRANSMISSION) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Backing plate cracked ... A ............ Require replacement.
Broken .................. A ............ Require replacement.
Contaminated with oil ... A ............ Require replacement.
Damper cushion broken ... A ............ Require replacement.
Damper cushion
collapsed .............. A ............ Require replacement.
Damper spring collapsed . A ............ Require replacement.
Damper spring missing .. C ........ ( 1) Require replacement.
Friction material cracked
through ................ B ............ Require replacement.
Friction material flaking
or chunking ............ B ............ Require replacement.
Friction material surface
cracking ............... B ......... No service suggested or
required.
Grooved ................. B ......... No service suggested or
required unless the pressure
plate or flywheel is being
resurfaced or replaced. In this
case, replacement of clutch
disc is required.
Ridged .................. B ......... No service suggested or
required unless the pressure
plate or flywheel is being
resurfaced or replaced. In this
case, replacement of clutch
disc is required.
Splines worn, affecting
performance ............ A ............ Require replacement.
Warped .................. A ............ Require replacement.
Wear exceeds
specifications (where
applicable) ............ B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
( 1) - Not all clutch discs have springs in all spring
chambers on the disc.
\
\
\
\
\
\
\
CLUTCH FORKS
CLUTCH FORK INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A .. Require repair or replacement.
Cracked ................. B .. Require repair or replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
Page 667 of 1333
Application Mile Service Mile Service
1983-86 2.6L 4-Cylinder
Automatic Transmission .... 7.9 (8.2) ................. 5.2
Manual Transmission ....... 6.9 (7.2) ................. 5.2
1987-90 2.6L 4-Cylinder
Automatic Transmission .... 7.9 (8.9) ................. 2.6
Manual Transmission ....... 6.9 (7.9) ................. 2.6
1989-96 3.0L V6
Automatic Transmission .... 6.1 (10.6) ................ 2.6
Manual Transmission ....... 5.1 (9.6) ................. 2.6
\
\
\
\
\
\
\
LUBRICATION SPECIFICATIONS
LUBRICATION SPECIFICATIONS TABLE\
\
\
\
\
\
\
Application Fluid Specifications
Brake & Clutch Fluid ........................... DOT 3 Or DOT 4
Engine Coolant ............. Ethylene-Glycol Antifreeze Coolant
Engine Oil ( 1)
Minimum Temperature
Greater Than 32
\bF (0\bC) ..... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10\bF (-23\bC) .. SAE 10W-30 Or 10W-40 API SG/CD
Maximum Temperature
Less Than 60
\bF (16\bC) ......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
\bF (-23\bC) ..... SAE 85W-90, 80W-90 API GL-5
Maximum Temperature
Less Than -30
\bF (-34\bC) ................... SAE 75W API GL-5
Power Steering Fluid ........................... Dexron-IIE ATF
Rear Axle (With Limited
Slip Differential) ........... Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic .................................... Dexron-IIE ATF
Manual Transaxle &
Transfer Case (4WD) ........... SAE 75W-85W, 75W-90 API GL-5
( 1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
FLUID CAPACITIES
FLUID CAPACITIES TABLE\
\
\
\
\
\
\
Application Quantity
A/C System R-12 Refrigerant
1983-87 .......................................... 24-26 Ozs.
1988-91 ............................................. 32 Ozs.
1992-93 ............................................. 28 Ozs.
A/C System R-134a Refrigerant ( 1)
1994-96 .......................................... 21-23 Ozs.
Automatic Transmission
1984-86 ................................. ( 2) 7.2 Qts. (6.8L)
1987-93 ..................................... 7.6 Qts. (7.2L)
1994-96 (3.0L SOHC) ......................... 7.6 Qts. (7.2L)
Page 668 of 1333
1994-96 (3.0L DOHC & 3.5L) .................. 9.0 Qts. (8.5L)
Cooling System
1983-88 ..................................... 8.5 Qts. (8.0L)
1989-96
2.6L ....................................... 9.7 Qts. (9.2L)
3.0L ...................................... 10.0 Qts. (9.5L)
3.5L ...................................... 10.0 Qts. (9.5L)
Differential
1983-88 ..................................... 1.9 Qts. (1.8L)
1989-93
2.6L ....................................... 1.9 Qts. (1.8L)
3.0L ....................................... 2.7 Qts. (2.6L)
1994-96
3.0L & 3.5L ................................ 2.7 Qts. (2.6L)
Engine Oil
1983-86 ..................................... 6.0 Qts. (5.8L)
1987 ........................................ 5.2 Qts. (5.0L)
1988 ........................................ 5.0 Qts. (4.8L)
1989-91 ..................................... 5.5 Qts. (5.3L)
1992-96 ..................................... 5.2 Qts. (4.9L)
Power Steering ................................ 1.1 Qts. (1.0L)
Fuel Tank
1983-88 .................................... 15.9 Gals. (60L)
1989-90
2.6L 2-Door ............................... 15.9 Gals. (60L)
3.0L 2-Door ............................... 19.9 Gals. (75L)
2.6L & 3.0L 4-Door .......................... 24 Gals. (92L)
1991-96 ...................................... 24 Gals. (92L)
Manual Transmission
1983-91 ..................................... 2.3 Qts. (2.2L)
1992 ........................................ 2.4 Qts. (2.3L)
1993-96 ..................................... 2.6 Qts. (2.5L)
Transfer Case
1983-91 ..................................... 2.3 Qts. (2.2L)
1992-96 ..................................... 2.4 Qts. (2.3L)
(1) - Use of R12 in a R134a system will result in SEVERE DAMAGE.
( 2) - 1983 model equipped with manual transmission only.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
1983-86
15 x 6JJ (Steel) .............................. 215 SR15
1987-88
Page 705 of 1333
![MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels](/manual-img/19/57332/w960_57332-704.png "MITSUBISHI MONTERO 1991 Service Manual \b\
\
\
\
\
\
\
Fluid Levels")
\b\
\
\
\
\
\
\
Fluid Levels
\b\
\
\
\
\
\
\
Braking System
\b\
\
\
\
\
\
\
Drive Shaft Boots
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Brake & Clutch Fluid ............................ DOT 3 Or DOT 4
Engine Coolant .............. Ethylene-Glycol Antifreeze Coolant
Engine Oil (
1)
Minimum Temperature
Greater Than 32
F (0
C) ...... SAE 20W-40 Or 20W-50 API SG/CD
Greater Than -10
F (-23
C) ..... SAE 10W-30, 10W-40 API SG/CD
Maximum Temperature
Less Than 60
F (16
C) .......... SAE 5W-30 Or 5W-40 API SG/CD
Front Axle & Conventional Rear Axle
Minimum Temperature
Greater Than -10
F (-23
C) ........... SAE 90, 85W-90, 80W-90
API GL-5
Maximum Temperature
Less Than -30
F (-34
C) .................... SAE 75W API GL-5
Power Steering Fluid ............................. Dexron-II ATF
Rear Axle (With Limited
Slip Differential) ............ Hypoid Gear Oil (8149630EX) Or
Equivalent
Transmission
Automatic ...................................... Dexron-II ATF
Manual Transaxle &
Transfer Case (4WD) ................. SAE 75W-85W, 75W-90 API
GL-4 Or GL-5
(
1) - Since temperature ranges for different oil grades overlap,
brief fluctuations in outside temperatures are no cause for
concern.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application Quantity
Automatic Transmission
1987-93 ...................................... 7.6 Qts. (7.2L)
1994 (3.0L SOHC) ............................. 7.6 Qts. (7.2L) \
1994 (3.0L DOHC & 3.5L) ...................... 9.0 Qts. (8.5L) \
1995 ......................................... 7.9 Qts. (7.5L)
Cooling System
1987-88 ...................................... 8.5 Qts. (8.0L)
1989-95
2.6L ........................................ 9.7 Qts. (9.2L)
3.0L ....................................... 10.0 Qts. (9.5L)
1994-95
3.5L ....................................... 10.0 Qts. (9.5L)
Differential
1987-88 ...................................... 1.9 Qts. (1.8L)