1991 MITSUBISHI MONTERO suspension

and No. 2. Install bearing caps with front mark arrow facing the same
direction as similar mark on cylinder head beside bearing journal.
Note bearing cap number and identification mark ("I" for intake
camshaft and "E" for exhaust). See Fig. 22.
3) Install front and rear bearing caps. Tighten bearing cap
bolts to specification. See TORQUE SPECIFICATIONS (3000GT) table at
end of article. Coat camshaft oil seal area with oil. Using Seal
Installer (MD998761), install camshaft oil seal. Using Circular
Packing Installer (MD998761), install circular packing.
4) Install crankshaft angle sensor adapter. To complete
installation, reverse removal procedure. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
REAR CRANKSHAFT OIL SEAL
Removal
Remove transaxle/transmission. See appropriate article in
TRANSMISSION SERVICING or CLUTCHES. Remove flywheel or drive plate.
Remove rear oil seal case. Pry seal from seal case.
Installation
To install, coat seal lip with oil. Using Seal Installer
(MD998718), install seal in seal case. Apply sealant to sealing
surface of seal case. Install seal case. Install flywheel or drive
plate. Tighten bolts to specification. See appropriate TORQUE
SPECIFICATIONS table at end of article. To complete installation,
reverse removal procedure.
WATER PUMP
Removal
Drain cooling system. Remove timing belt and crankshaft
sprocket. See TIMING BELT under REMOVAL & INSTALLATION. Remove coolant
pipes to water pump (if required). Remove water pump bolts, noting
length and location for reassembly reference. Remove water pump.
Installation
To install, reverse removal procedure using new gasket and
"O" rings. Coat all "O" rings with water before installation. Install
water pump and gasket. Tighten bolts to specification. See appropriate
TORQUE SPECIFICATIONS table at end of article.
OIL PAN
Removal (Montero)
1) Remove hood. Remove skid plate and lower covers. Raise and
support vehicle. Disconnect and remove exhaust pipe from exhaust
manifolds. Drain engine oil. Remove starter cover and starter. Remove
oil pressure sending unit connector. Remove front suspension
crossmember.
2) Remove transmission stays. Remove ground cable and motor
mount heat shields. Attach engine hoist. Remove motor mount bolts.
Raise engine, and insert a 1" wood spacer between front insulator and
mounts. Lower engine onto wood blocks.
3) Raise vehicle using a hoist. Remove oil pan bolts. Using
Seal Cutter (MD998727), separate oil pan from cylinder block. Remove
pan from vehicle.
Removal (Pickup)
1) Remove skid plate and lower covers. Raise and support
vehicle. Drain engine oil. Using Steering Linkage Puller (C-3894-A or
MB990635), disconnect relay rod from idler arm and steering box.
2) Remove oil pan bolts. Using Seal Cutter (MD998727),

HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards

are continually republished. In addition to these, standards for Drive
Train and Transmissions have recently been promulgated. Participating
shops utilize these Uniform Inspection & Communication Standards as
part of the inspection process and for communicating their findings to
their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,

SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACHING HARDWARE
WHEEL BEARINGS, RACES AND SEALS
WHEEL CYLINDERS
WIRING HARNESSES
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt:\
1) a Pledge of Assurance to their Customers and
2) the Motorist Assurance Program Standards of Service.
All participating service providers have agreed to subscribe
to this Pledge and to adhere to the promulgated Standards of Service
demonstrating to their customers that they are serious about customer
satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not

satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS AND SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.

5) Remove the LSPV load-sensing spring. Slowly depress the
brake pedal. Check the readings on the pressure gauges. Refer to the
LSPV PRESSURE SPECIFICATIONS table.
6) Install LSPV load-sensing spring. Load weight into rear of
vehicle until measured spring length distance is 7.0" (178 mm) with
lever slightly pressed in. See Fig. 1.
7) Slowly depress brake pedal. Check readings on pressure
gauges. See LSPV PRESSURE SPECIFICATIONS table. If fluid pressure is
not within specification, ensure all other brake system components are
okay. If other components are okay, replace LSPV assembly.
LSPV PRESSURE SPECIFICATIONS (PICKUP & RAM-50)









\









\









\









\









\









\






Application Inlet Pressure Outlet Pressure
psi (kg/cm) psi (kg/cm)
Load-Sensing Spring
Removed ........... 853 (60) ......... 242-327 (17-23)
Installed ........ 1991 (140) .... ( 1) 299-583 (21-40)
( 1) - On vehicles with 2WD and heavy-duty suspension,
outlet pressure is 526-697 psi (37-49 kg/cm
).








\









\









\









\









\









\






PROPORTIONING VALVE (NON-LOAD-SENSING) (MONTERO)
Pressure Test
1) Connect pressure gauges to input and output ports of the
proportioning valve. See Fig. 5. Bleed brake hydraulic system. Refer
to BLEEDING BRAKE SYSTEM .
2) Slowly depress brake pedal. Check readings on pressure
gauges. See the PROPORTIONING VALVE PRESSURE SPECIFICATIONS table. If
fluid pressures are not within specification, replace proportioning
valve.
Fig. 5: Connecting Pressure Gauges to Proportioning Valve (Typical)
Courtesy of Mitsubishi Motor Sales of America.
PROPORTIONING VALVE PRESSURE SPECIFICATIONS (MONTERO)









\









\









\









\









\









\

Fig. 1: Front Drive Axle & Suspension
Courtesy of Chrysler Motors.
INNER SHAFT & BEARING R & I
REMOVAL
1) Remove right drive axle. See DRIVE AXLES R & I in this
article. Remove inner shaft from differential carrier. Pry dust seal
from housing tube assembly using a screwdriver if replacement is
required. See Fig. 1.
2) If oil seal replacement is required, remove housing tube.
Using slide hammer, remove oil seals. Bend outer area of dust cover
inward on inner shaft. Press bearing from shaft. Remove dust cover
from shaft.
INSPECTION
Inspect inner shaft for damaged splines or threads. Inspect
bearing for roughness or damage. Measure shaft O.D. Replace shaft if
not within specification. See INNER SHAFT SPECIFICATIONS table.

\003
DRIV E A XLE - R EA R N O N-IN TE G RAL
1991 M it s u bis h i M onte ro
199192 DRIVE AXLES
Differentials & Axle Shafts - Rear Non-Integral
Mitsubishi: Montero, Pickup
DESCRIPTION
Rear axle features a rigid banjo-type housing with semi-
floating axle shafts. Differential consists of hypoid reduction gears
and straight bevel differential gears. Limited Slip Differential (LSD)\
is available on all models.
AXLE RATIO & IDENTIFICATION
Ratio is determined by dividing number of ring gear teeth by
number of drive pinion teeth.
AXLE RATIO SPECIFICATIONS









\









\









\









\









\









\









\


Application Ratio
Montero .................................................. 4.63
Pickup
2WD w/Light Suspension ................................. 3.91
2WD w/Heavy Suspension ................................. 4.22
4WD .................................................... 4.22









\









\









\









\









\









\









\


LUBRICATION
CAPACITY
REAR AXLE GEAR OIL CAPACITY








\









\









\









\









\









Application Pts. (L)
Montero .................................. 5.4 (2.5)
Pickup
Conventional
2WD ................................... 3.2 (1.5)
4WD ................................... 5.5 (2.6)
LSD .................................... 5.5 (2.6)









\









\









\









\









\









FLUID TYPE
Conventional differentials use API classification GL-5 SAE
80W or 90W. Limited slip differentials use Mitsubishi Gear Oil
(8149630 EX) or Mopar Gear Oil (4318058) and Mopar Friction Modifier\
(4318060).
TROUBLE SHOOTING
DRIVE AXLE (RWD) TROUBLE SHOOTING








\









\









\









\









\









\









\


PROBLEM
Possible Cause Action