1991 MITSUBISHI MONTERO wheel bolts

install, reverse removal procedure using new gaskets and "O" rings.
Coat "O" ring with fuel before installation.
2) Install lower intake manifold gasket with adhesive side
toward intake manifold and gasket protrusions facing outboard of
engine. Tighten bolts and nuts to specification. See appropriate
TORQUE SPECIFICATIONS table at end of article. Check for fuel leaks.
TURBOCHARGER
Removal (Front)
1) Drain coolant, and remove radiator. Disconnect exhaust
pipe from turbo. Remove all air intake pipes. Note match marks and
installation depth on air pipes and hoses for reinstallation. Remove
serpentine drive belt. Remove alternator. Remove A/C compressor and
bracket, and support aside.
2) Remove O2 sensor. Remove dipstick assembly and turbo heat
shield. Disconnect turbo coolant feed and return lines. Disconnect
turbo oil feed and return lines. Remove turbocharger assembly.
Removal (Rear)
1) Drain coolant. Remove battery. Disconnect accelerator
cable at bracket and throttle body. Disconnect exhaust pipe from
turbo. Remove all air intake pipes and heat shields. Disconnect
accelerator cable at pedal.
2) Remove clutch booster vacuum hose. Remove O2 sensor.
Remove EGR pipe and turbo heat shield. Disconnect turbo coolant feed
and return lines. Disconnect turbo oil feed and return lines. Remove
turbocharger assembly.
CAUTION: DO NOT allow foreign material into turbocharger air intakes
or coolant and oil passages.
Inspection (Front & Rear)
1) Inspect turbocharger for oil leakage. Check turbine and
compressor wheels for cracks and other damage. Both wheels should turn
easily by hand.
2) Apply 6.8 psi (61 kPa) vacuum to wastegate diaphragm.
Ensure wastegate operates and diaphragm holds vacuum pressure. Use
care when cleaning gasket surfaces so no foreign material enters
turbocharger oil, coolant and air passages.
Installation (Front & Rear)
Refill turbocharger with clean engine oil through oil pipe
installation hole. To complete installation, reverse removal
procedure. Align match marks, and install air pipes and hoses to
proper depth.
EXHAUST MANIFOLDS
Removal (Montero & Pickup)
1) Remove splash shields. Remove O2 sensor. Remove exhaust
pipe-to-manifold nuts. Lower exhaust pipe, and remove gasket. Remove
heat protector. To remove right exhaust manifold, remove air duct,
engine lift bracket and alternator bracket.
2) To remove left exhaust manifold, remove EGR pipe and
gasket. Remove front intake manifold plenum bracket. Remove exhaust
manifolds and gaskets.
Inspection (Montero & Pickup)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. Check mounting surfaces of manifold
and cylinder head for warpage. Repair or replace components if warpage
exceeds .012" (.30 mm).

and No. 2. Install bearing caps with front mark arrow facing the same
direction as similar mark on cylinder head beside bearing journal.
Note bearing cap number and identification mark ("I" for intake
camshaft and "E" for exhaust). See Fig. 22.
3) Install front and rear bearing caps. Tighten bearing cap
bolts to specification. See TORQUE SPECIFICATIONS (3000GT) table at
end of article. Coat camshaft oil seal area with oil. Using Seal
Installer (MD998761), install camshaft oil seal. Using Circular
Packing Installer (MD998761), install circular packing.
4) Install crankshaft angle sensor adapter. To complete
installation, reverse removal procedure. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
REAR CRANKSHAFT OIL SEAL
Removal
Remove transaxle/transmission. See appropriate article in
TRANSMISSION SERVICING or CLUTCHES. Remove flywheel or drive plate.
Remove rear oil seal case. Pry seal from seal case.
Installation
To install, coat seal lip with oil. Using Seal Installer
(MD998718), install seal in seal case. Apply sealant to sealing
surface of seal case. Install seal case. Install flywheel or drive
plate. Tighten bolts to specification. See appropriate TORQUE
SPECIFICATIONS table at end of article. To complete installation,
reverse removal procedure.
WATER PUMP
Removal
Drain cooling system. Remove timing belt and crankshaft
sprocket. See TIMING BELT under REMOVAL & INSTALLATION. Remove coolant
pipes to water pump (if required). Remove water pump bolts, noting
length and location for reassembly reference. Remove water pump.
Installation
To install, reverse removal procedure using new gasket and
"O" rings. Coat all "O" rings with water before installation. Install
water pump and gasket. Tighten bolts to specification. See appropriate
TORQUE SPECIFICATIONS table at end of article.
OIL PAN
Removal (Montero)
1) Remove hood. Remove skid plate and lower covers. Raise and
support vehicle. Disconnect and remove exhaust pipe from exhaust
manifolds. Drain engine oil. Remove starter cover and starter. Remove
oil pressure sending unit connector. Remove front suspension
crossmember.
2) Remove transmission stays. Remove ground cable and motor
mount heat shields. Attach engine hoist. Remove motor mount bolts.
Raise engine, and insert a 1" wood spacer between front insulator and
mounts. Lower engine onto wood blocks.
3) Raise vehicle using a hoist. Remove oil pan bolts. Using
Seal Cutter (MD998727), separate oil pan from cylinder block. Remove
pan from vehicle.
Removal (Pickup)
1) Remove skid plate and lower covers. Raise and support
vehicle. Drain engine oil. Using Steering Linkage Puller (C-3894-A or
MB990635), disconnect relay rod from idler arm and steering box.
2) Remove oil pan bolts. Using Seal Cutter (MD998727),

separate oil pan from cylinder block. Remove pan from vehicle.
Removal (3000GT)
1) Raise and support vehicle. Remove engine undercovers.
Drain engine oil. Disconnect O2 sensor connector. Remove front exhaust
pipe from manifolds. On All-Wheel Drive (AWD) models, drain transfer
assembly. Remove front air dam. Remove AWD drive shaft and transfer
assembly.
2) On turbocharged models, remove oil return lines from oil
pan. On all models, remove starter. Remove crossmember and transaxle
stays. Remove bellhousing cover. Remove oil pan bolts. Using Seal
Cutter (MD998727), separate oil pan from cylinder block. Remove pan
from vehicle.
Inspection (All Models)
Clean sealant from oil pan mating surface on engine block and
oil pan. Check oil pan for cracks and damage. Check sealing surface
for damage and deformation. Inspect oil pick-up screen for damage.
Installation (All Models)
1) To install, reverse removal procedure. Apply sealant to
oil pan flange in a continuous .16" (4 mm) diameter bead. See Fig. 22.
Install oil pan within 15 minutes of applying sealant.
2) Tighten bolts to specification in proper sequence. See
appropriate TORQUE SPECIFICATIONS table at end of article. Wait at
least 30 minutes before adding oil and starting engine. On AWD models,
refill transfer assembly with GL-4 hypoid gear oil. On all models,
complete installation by reversing removal procedure.
Fig. 22: Sealant Application & Oil Pan Bolt Tightening Sequence
Courtesy of Mitsubishi Motor Sales of America, Inc.
OVERHAUL

Measure cylinder bore and piston skirt diameter. Piston skirt
diameter should be measured at 90-degree angle to piston pin.
Clearance between piston and cylinder bore must be within
specification. See appropriate PISTONS, PINS & RINGS table under
ENGINE SPECIFICATIONS at end of article.
PISTON PIN REPLACEMENT
1) Note reference mark on top of piston and connecting rod.
See Fig. 23 . Using press and Piston Pin Remover/Installer (MD998184
for SOHC or MD998765 for DOHC), remove pin.
2) Inspect piston for cracks and damage. Check ring side
clearance. Replace piston if not within specification. See appropriate
PISTONS, PINS & RINGS table under ENGINE SPECIFICATIONS.
3) Check connecting rod for bend and twist. Replace
connecting rod if twist exceeds .004" (.10 mm) or bend exceeds .002"
(.05 mm). Pressure required to install pin in rod is 1686-3934 lbs.
(7500-17,500 N).
4) Position piston on connecting rod. Ensure reference marks
on top of piston and connecting rod are aligned. See Fig. 23.
Lubricate all components with oil. To install, reverse removal
procedure. Ensure piston pin is centered in piston.
NOTE: Install piston with reference mark aligned with connecting
rod reference mark. See Fig. 23.
CRANKSHAFT & MAIN BEARINGS
1) Remove flywheel or drive plate. Remove
transaxle/transmission mounting plate and rear seal case. Remove oil
pump, oil pan and oil pick-up tube. Ensure connecting rods and main
bearing cap are marked for location.
2) Remove connecting rod caps and bearings. Note direction of
arrow on main bearing cap. Remove main bearing cap. See Fig. 24.
Ensure all components are placed in correct order. Remove crankshaft.
Remove main bearings from cylinder block. Mark bearings for location.
3) Inspect crankshaft for cracks and damaged gear or threads.
Check crankshaft for taper and out-of-round. Replace or repair
crankshaft if it is not within specification. See CRANKSHAFT, MAIN &
CONNECTING ROD BEARINGS table under ENGINE SPECIFICATIONS at end of
article.
4) Install upper main bearings in cylinder block. Ensure oil
hole is aligned and bearing is properly seated. Lubricate bearings
with engine oil. Install thrust bearings on No. 3 main bearing journal
with oil grooves toward crankshaft thrust surface.
5) Install crankshaft in block. Install thrust bearing on No.
3 main bearing cap with oil grooves toward crankshaft thrust surface.
Install main bearing cap with arrow toward front of engine.
6) Check oil clearance using Plastigage method. Tighten bolts
to specification in proper sequence. See Fig. 24. See appropriate
TORQUE SPECIFICATIONS table at end of article. Remove main bearing
cap. Clearance must be within specification. See CRANKSHAFT, MAIN &
CONNECTING ROD BEARINGS table. If oil clearance exceeds specification,
replace bearings or crankshaft.
7) Ensure crankshaft rotates freely with main bearing cap
installed. Check crankshaft end play. See CRANKSHAFT, MAIN &
CONNECTING ROD BEARINGS table.
8) Install connecting rod caps and bearings. Ensure
components are installed in original location. Tighten rod nuts to
specification. See appropriate TORQUE SPECIFICATIONS table. Ensure
connecting rods move freely on crankshaft. To complete installation,
reverse removal procedure. Tighten bolts to specification.

OIL PRESSURE
Oil pressure should be at least 11.4 psi (.8 kg/cm) at idle
and engine oil temperature of 167-194F (75-90C).
OIL PUMP
Removal
Remove timing belt and crankshaft sprocket. See TIMING BELT
under REMOVAL & INSTALLATION. Remove oil pan. See OIL PAN under
REMOVAL & INSTALLATION. Remove oil filter and mounting bracket. Remove
oil pump and gasket from cylinder block. Note bolt length and location
for installation.
Disassembly & Inspection
1) Disassemble pump, and check for scoring and cracks.
Install rotors in pump body. Check clearance between driven rotor and
pump body. See OIL PUMP SPECIFICATIONS table. Place straightedge
across pump body to check rotor side clearance.
2) Check clearance between straightedge and both rotors.
Replace rotor set or pump assembly if not within specification. Ensure
relief valve slides freely in pump body bore. Inspect relief valve
spring for damage.
OIL PUMP SPECIFICATIONS TABLE









\









\









\









\









\









\






Application In. (mm)
Driven Rotor-To-Pump Body ........ .0039-.0071 (.099-.180)
Rotor Side Clearance ............. .0016-.0037 (.041-.094)









\









\









\









\









\









\






Reassembly & Installation
1) Reassemble pump. Tighten pump rear cover bolts to
specification. See appropriate TORQUE SPECIFICATIONS table in this
article. Install oil pump and gasket. Ensure splined teeth of oil pump
align with crankshaft. Install bolts, and tighten to specification.
2) If oil seal was removed, coat new seal with grease. Using
Seal Installer (MD998717), install seal in oil pump until flush with
case. Install remaining components.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE (MONTERO & PICKUP)








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Air Intake Plenum Stay Bolts ............... 11-14 (15-19)
Camshaft Bearing Cap Bolt .................. 14-15 (19-20)
Camshaft Sprocket Bolt ..................... 58-72 (79-98)
Connecting Rod Nut ......................... 37-38 (50-52)
Crankshaft Pulley Bolt
Montero .............................. 108-116 (146-157)
Pickup ............................... 130-137 (176-186)
Cylinder Head Bolt ( 1)
Cold Engine .............................. 65-72 (88-98)
Drive Plate Bolt ........................... 53-55 (72-75)
Exhaust Manifold Nut ....................... 11-16 (15-22)
Flywheel Bolt .............................. 53-55 (72-75)
Intake Manifold Bolts ...................... 11-15 (15-20)
Left Engine Support Bracket Bolt ........... 15-21 (20-30)

Main Bearing Cap Bolt ...................... 55-61 (75-83)
Oil Pick-Up Tube Bolt ...................... 11-15 (15-20)
Rear Engine Support
Bracket-To-Engine Bolt .................... 13-18 (18-25)
Relief Valve Plug .......................... 29-36 (39-49)
Right Engine Support Bracket Bolt
10x22 mm ................................. 25-36 (34-49)
12x22 mm & 12x32 mm ...................... 47-61 (64-83)
Rocker Shaft ............................... 14-15 (19-20)
Timing Belt Tensioner Bolt ................. 16-21 (22-29)
Water Pump Bolt ............................ 14-20 (19-27)
INCH Lbs. (N.m)
Delivery Pipe Bolt ......................... 84-108 (9-12)
Distributor Adapter Bolt .................. 108-132 (12-15)
Oil Filter Bracket Bolt .................. 108-120 (12-14)
Oil Pan Bolt ................................. 48-60 (5-7)
Oil Pump Cover Bolt ........................ 72-108 (8-12)
Oil Pump Mounting Bolt ................... 108-120 (12-14)
Rear Seal Case Bolt ........................ 84-108 (9-12)
Rocker Cover Bolt ............................ 72-84 (8-9)
Throttle Body Bolt ......................... 84-108 (9-12)
Timing Belt Cover Bolt ..................... 84-108 (9-12)
Transmission Mounting Plate Bolt ........... 84-108 (9-12)
( 1) - Tighten in 2 steps using proper sequence.
See Fig. 4.









\









\









\









\









\









\






TORQUE SPECIFICATIONS TABLE (3000GT)








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Air Intake Plenum Stay Bolts ..................... 13 (18)
Automatic Tensioner Bolt ......................... 17 (23)
Camshaft Bearing Cap Bolt ........................ 15 (20)
Camshaft Sprocket Bolt ........................... 65 (88)
Connecting Rod Nut ............................... 38 (52)
Crankshaft Pulley Bolt
SOHC ................................. 108-116 (146-157)
DOHC ................................. 130-137 (176-186)
Cylinder Head Bolt ( 1)
SOHC ................................... 76-83 (103-113)
DOHC
Non-Turbo ............................. 76-83 (103-113)
Turbo ................................. 87-94 (118-127)
Distributor Adapter Bolt ......................... 11 (15)
Drive Plate Bolt ................................. 55 (75)
Engine Support Bracket Bolt
Except 10x40 mm ........................ 76-83 (103-113)
10x40 mm ................................. 47-54 (63-73)
Exhaust Manifold Nut ............................. 13 (18)
Flywheel Bolt .................................... 55 (75)
Intake Manifold Bolt
Lower Manifold
Non-Turbo ............................... 11-15 (15-20)
Turbo .................................... 9-11 (12-15)
Upper Manifold ................................. 13 (18)
Main Bearing Cap Bolt ............................ 58 (79)
Oil Filter Bracket Bolt .......................... 11 (15)
Oil Pick-Up Tube Bolt ............................ 14 (19)
Oil Pump Mounting Bolt ........................... 11 (15)

Removal
1) Raise and support vehicle. Remove front wheel(s). Separat\
e
rubber flex hose from hydraulic line at brake hose mount, located on
strut housing. Secure end of hydraulic line to prevent spillage of
brake fluid.
2) Remove hose clip from brake hose mount. Disconnect brake
hose from caliper. Remove upper and lower caliper-to-steering knuckle
bolts. Lift caliper body upward. Remove caliper.
Installation
To install, reverse removal procedure. Tighten bolts to
specification. See the TORQUE SPECIFICATIONS table. Bleed brake
system. See BLEEDING BRAKE SYSTEM .
FRONT BRAKE ROTOR
Removal (Montero, Pickup 4WD & Ram-50 4WD)
Raise and support vehicle. Remove and support brake calipers.
Place hub in free-wheeling position. Remove drive hub cover using an
oil filter wrench and protective cloth. Remove snap ring, shim and
free-wheeling hub from drive axle. See Fig. 7. Remove lock washer.
Remove lock nut using Lock Nut Wrench (MB990954). Remove front hub
assembly.
Fig. 7: Exploded View of Front Brake Assembly (4WD)
Courtesy of Mitsubishi Motor Sales of America.
Installation
1) Install front hub assembly. Install and tighten lock nut
to 94-145 ft. lbs. (127-197 N.m), and then loosen and retighten to 18
ft. lbs. (24 N.m). Loosen lock nut 30-40 degrees. Reverse removal
procedure for remaining components. After installation is complete,
check drive axle end play. Adjust end play if not .002" (.05 mm) or
less. Rotate drive axle forward and rearward until maximum end play is
obtained.
2) If adjusting axle shaft end play, use proper shim to
obtain desired end play. Shim is located behind snap ring on end of
drive axle. Install shim, and recheck axle end play.
Removal (Pickup 2WD & Ram-50 2WD)
Raise and support vehicle. Remove front caliper. Remove hub
(dust) cap, cotter pin and nut. Remove washer and outer wheel bearing.\
Remove front hub assembly. Remove bolts attaching rotor to front hub,
and separate assemblies.

cylinder. Disconnect parking brake cable end, and remove cable
attaching bolts. Remove brake backing plate, bearing case and axle
shaft as an assembly. If axle shaft binds, use slide hammer with
puller to remove.
2) Remove shims, "O" ring and snap ring. Retain shims for
reassembly. Secure axle shaft assembly in a vise, and remove one
retainer bolt from backing plate. Push bearing case completely to side
of dust cover. Place adhesive tape around edge of bearing case at
retainer bolt hole to prevent damage.
3) Secure axle shaft, and grind retainer ring until retainer
ring wall thickness is .04-.06" (1.0-1.5 mm) on axle shaft side and
retainer ring wall thickness is .08" (2.0 mm) on bearing side. See
Fig. 11.
CAUTION: DO NOT damage bearing case or axle shaft when grinding or
chiseling retainer ring.
4) Change angle of grind, and remove remaining .08" (2.0 mm)\
of retainer ring wall on bearing side. See Fig. 11. Using a chisel,
cut retainer ring, and remove. DO NOT damage axle shaft.
Fig. 11: Grinding Bearing Retainer Ring (Pickup & Ram-50)
Courtesy of Mitsubishi Motor Sales of America.
5) Install Puller (MB990787-01) to remove bearing case from
axle shaft. Rotate nuts with equal force to remove wheel bearing.