1991 MITSUBISHI MONTERO maintenance schedule

Engine pre-oiling can be done using pressure oiler (if
available). Connect pressure oiler to cylinder block oil passage
such as oil pressure sending unit. Operate pressure oiler long enough
to ensure correct amount of oil has filled crankcase. Check oil level
while pre-oiling.
If pressure oiler is not available, disconnect ignition
system. Remove oil pressure sending unit and replace with oil pressure
test gauge. Using starter motor, rotate engine starter until gauge
shows normal oil pressure for several seconds. DO NOT crank engine
for more than 30 seconds to avoid starter motor damage.
Ensure oil pressure has reached the most distant point from
the oil pump. Reinstall oil pressure sending unit. Reconnect ignition
system.
INITIAL START-UP
Start the engine and operate engine at low speed while
checking for coolant, fuel and oil leaks. Stop engine. Recheck coolant
and oil level. Adjust if necessary.
CAMSHAFT
Break-in procedure is required when a new or reground
camshaft has been installed. Operate and maintain engine speed between
1500-2500 RPM for approximately 30 minutes. Procedure may vary due to
manufacturers recommendations.
PISTON RINGS
Piston rings require a break-in procedure to ensure seating
of rings to cylinder walls. Serious damage may occur to rings if
correct procedures are not followed.
Extremely high piston ring temperatures are produced obtained
during break-in process. If rings are exposed to excessively high RPM
or high cylinder pressures, ring damage can occur. Follow piston ring
manufacturer's recommended break-in procedure.
FINAL ADJUSTMENTS
Check or adjust ignition timing and dwell (if applicable).
Adjust valves (if necessary). Adjust carburetion or injection idle
speed and mixture. Retighten cylinder heads (if required). If
cylinder head or block is aluminum, retighten bolts when engine is
cold. Follow the engine manufacturer's recommended break-in procedure
and maintenance schedule for new engines.
NOTE: Some manufacturer's require that head bolts be retightened
after specified amount of operation. This must be done to
prevent head gasket failure.

IN TE R FE R EN CE V ER IF IC ATIO N C HEC K F O R O HC E N G IN E
1991 Mitsubishi Montero
Maintenance & Service Information
1983-96 Mitsubishi - Timing Belt Information
Cordia, Diamante, Eclipse, Expo, Expo LRV, Galant, Mirage,
Montero, Pickup, Precis, Sigma, Tredia, Van, 3000GT
TIMING BELT INTERFERENCE VERIFICATION INFORMATION
TIMING BELT INTERFERENCE CAUTION
NOTE: CAMSHAFT DRIVE BELTS OR TIMING BELTS - The condition of
camshaft drive belts should always be checked on vehicles
which have more than 50,000 miles. Although some
manufacturers do not recommend replacement at a specified
mileage, others require it at 60,000-100,000 miles. A
camshaft drive belt failure may cause extensive damage to
internal engine components on most engines, although some
designs do not allow piston-to-valve contact. These designs
are often called "Free Wheeling". Many manufacturers changed
their maintenance and warranty schedules in the mid-1980's to
reflect timing belt inspection and/or replacement at
50,000-60,000 miles. Most service interval schedules shown in
this section reflect these changes. Belts or components
should be inspected and replaced if any of the following
conditions exist:
* Crack Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
TIMING BELT INTERFERENCE CHECK MENU
TIMING BELT INTERFERENCE VERIFICATION TABLE ( 1)








\









\









\









\









\









\






Replacement Interval
Application Engine (Miles)
Passenger Cars
Cordia
1983-88 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
2.0L 4-Cyl. ............ ( 4) 60,000
Diamante
1992-96 ...... ( 2) 3.0L V6 (DOHC) ............. 60,000
3.0L V6 (SOHC) ........... ( 4) 60,000
Eclipse
1990-94 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
1990-95 ....... ( 2) 2.0L 4-Cyl. ........... ( 4) 60,000
1990-94 ... ( 2) 2.0L 4-Cyl. Non-Turbo ..... ( 4) 60,000
1990-96 ..... ( 2) 2.0L 4-Cyl. Turbo ....... ( 4) 60,000
1996 ........... ( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Expo
1992-95 .......... 1.8L 4-Cyl. ................ 60,000
( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Expo LRV
1995 ............. 1.8L 4-Cyl. ................ 60,000
( 2) 2.4L 4-Cyl. .......... ( 4) 60,000
Galant

1985-87 ........ (2) 2.4L 4-Cyl. .......... ( 4) 60,000
1988 ............... 3.0L V6 .............. ( 3) 60,000
1989-93 .... ( 2) 2.0L 4-Cyl. (DOHC) ....... ( 4) 60,000
2.0L 4-Cyl. (SOHC) ........ ( 4) 60,000
1994-96 .... ( 2) 2.4L 4-Cyl. (DOHC) ....... ( 4) 60,000
2.4L 4-Cyl. (SOHC) ........ ( 4) 60,000
Mirage
1985-96 ........ ( 2) 1.5L 4-Cyl. .............. 60,000
1985-88 ..... ( 2) 1.6L 4-Cyl. Turbo ........... 60,000
1989, 1991 ..... ( 2) 1.6L 4-Cyl. .............. 60,000
1993-96 ........... 1.8L 4-Cyl ................ 60,000
Precis
1987-93 ........ ( 2) 1.5L 4-Cyl. .............. 60,000
Sigma
1989-90 ............ 3.0L V6 .............. ( 3) 60,000
Tredia
1983-88 .......... 1.8L 4-Cyl. ............ ( 4) 60,000
2.0L 4-Cyl. ............ ( 4) 60,000
3000GT
1991-96 .......... ( 2) 3.0L V6 ................ 60,000
Light Trucks
Montero
1985-96 ............ 3.0L V6 .............. ( 3) 60,000
1994-96 ............ 3.5L V6 .............. ( 3) 60,000
Pickup
1983-89 ........... 2.0L 4-Cyl. ........... ( 3) 60,000
1983-86 ... ( 2) 2.3L 4-Cyl. Turbo Diesel .. ( 4) 60,000
1990-96 ........... 2.4L 4-Cyl. ........... ( 4) 60,000
3.0L V6 .............. ( 3) 60,000
Van
1987-90 ........... 2.4L 4-Cyl. ........... ( 4) 60,000
( 1) - Other interference engine applications may exist which
are not indicated here.
( 2) - Interference engine. Check for possible damage to
piston(s) or valve(s) if there has been a timing belt
failure.
( 3) - Although the vehicle manufacturer does not recommend a
specific scheduled maintenance interval, aftermarket
belt manufacturers suggest the belt be replaced at
60,000 mile intervals.
( 4) - Vehicle manufacturer recommends replacing all belts at
the same time.









\









\









\









\









\









\

MAIN TE N AN CE IN FO RM ATIO N

1991 M it s u bis h i M onte ro
1983-96 MAINTENANCE
Mitsubishi Maintenance Information
Montero
* PLEASE READ THIS FIRST *
NOTE: For scheduled maintenance intervals and the related fluid
capacities, fluid specifications and labor times for major
service intervals, see SCHEDULED SERVICES article below:
* SCHEDULED SERVICES - 1983-86
* SCHEDULED SERVICES - 1987-95
* SCHEDULED SERVICES - 1996
Warranty information and specifications for fluid
capacities, lubrication specifications, wheel and tire size,
and battery type are covered in this article.
MODEL IDENTIFICATION
VIN LOCATION
The Vehicle Identification Number (VIN) is located on the
left side of the dash panel at the base of the windshield. The VIN
chart explains the code characters.
VIN CODE ID EXPLANATION
Numbers preceding the explanations in the legend below refer
to the sequence of characters as listed on VIN identification label.
See VIN example below.








\









\









\









\









\









\








 
(VIN) J A 4 F J 4 3 E 1 H J 0 0 0 0 0 1 


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 










\









\









\









\









\









\








1 - Manufacturing Country
J
* Japan
2 - Manufacturer
A * Mitsubishi Motor Corp.
3 - Vehicle Type
4 * Multi-Purpose Vehicle
7 * Truck
4 - GVW & Brake Type
F * 4001-5000 Lbs., Hydraulic Brakes
G * 5001-6000 Lbs., Hydraulic Brakes
5 - Vehicle Line
J, K Or R * Montero
6 - Vehicle Series
2 * Low
3 * Medium

4 * High
5 * Premium
7 - Body Type
1 * 5-Door Wagon
2 * 2-Door Canvas Top
3 * 2-Door Metal Top (1983-86)
3 * 3-Door Metal Top Or Van (1987 & Newer Models)
8 - Engine Type
E * 2.6L 4-Cylinder
H * 3.0L V6
M * 3.5L V6
S * 3.0L V6
7 * 2.6L 4-Cylinder (1983)
9 - VIN Check Digit
* 1 Through 9 Or X
10 - Vehicle Model Year
D * 1983
E * 1984
F * 1985
G * 1986
H * 1987
J * 1988
K * 1989
L * 1990
M * 1991
N * 1992
P * 1993
R * 1994
S * 1995
T * 1996
11 - Assembly Plant
Y * Ohye, Japan (1983)
Y * Nagoya, Japan (1984)
J * Nagoya, Japan (1985-96)
12 - Transmission Code (1983-85)
4 * 5-Speed M/T (1984-85 Federal Vehicles)
5 * 5-Speed M/T (1984-85 California Vehicles)
7 * 5-Speed M/T (1983 Federal Vehicles)
7 * A/T (1984-85 Federal Vehicles)
8 * A/T (1984-85 California Vehicles)
12-17 - Serial Number (1986-96)
* Sequential Production Number
13-17 - Serial Number (1983-85)
* Sequential Production Number
MAINTENANCE SERVICE INFORMATION
SEVERE & NORMAL SERVICE DEFINITIONS
NOTE: Use the Severe Service schedule if the vehicle to be serviced
is operated under ANY (one or more) of these conditions:
Service is recommended at mileage intervals based on vehicle
operation. Service schedules are based on the following primary

operating conditions.
Normal Service
* Driven More Than 10 Miles Daily
* No Operating Conditions From Severe Service Schedule
Severe Service (Unique Driving Conditions)
* Short Trips In Freezing Temperatures
* Towing Or Commercial Use
* Driving Off-Road Or In Salty Or Sandy Areas
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving
* Extensive Idling
CAMSHAFT TIMING BELT
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules in
this manual reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
Replace camshaft timing belt at 60,000 mile intervals.
SERVICE POINT LOCATIONS
Fig. 1: Service Point Locations (1983-86 2.6L 4-Cylinder Engine)
Courtesy of Mitsubishi Motor Sales of America.

WARNING: Keep hands away from radiator fan. Fan is controlled by a
thermostatic switch which may come on or run for up to
15 minutes even after engine is turned off.
WARRANTY INFORMATION
CAUTION: Always refer to customer's copy of warranty information for
specific model application and/or coverage limitations.
NEW VEHICLE LIMITED WARRANTY
Covers all manufacturer-installed parts and components for
any repairs, replacements or adjustments needed to correct defects in
materials or workmanship under normal use and maintenance for 36
months or 36,000 miles, whichever comes first, from date of delivery
to the first retail buyer or first date of use.
POWERTRAIN LIMITED WARRANTY
Upon expiration of New Vehicle Limited Warranty, this
warranty covers powertrain against defects in materials or workmanship
up to a maximum of 36 months or 50,000 miles, whichever occurs first.
On 1991-96 models, warranty period is extended to 5 years or 60,000
miles, whichever occurs first. See copy of warranty for specific
components covered.
BATTERY WARRANTY
Covers replacement of original battery for 12 months or 12,
000 miles, whichever occurs first.
AIR CONDITIONER WARRANTY
Covers manufacturer's air conditioners for 36 months or 36,
000 miles, whichever occurs first. Air conditioner refrigerant charge
is covered for the first 12 months or 12,000 miles, whichever occurs
first. On 1992-96 models, refrigerant is covered only as part of a
warranty repair.
ANTI-CORROSION PERFORATION LIMITED WARRANTY
Covers any body sheet metal panel found to have developed
perforation (rust-through) due to corrosion for 5 years regardless of
mileage. Outer panel coverage extends to 7 years or 100,000 miles,
whichever occurs first, on 1992-96 models.
EMISSION SYSTEM DEFECT WARRANTY (EXCEPT CALIFORNIA)
Warrants that the vehicle was designed, built and equipped to
conform at the time of sale with all applicable U.S. emission
standards. Covers any repairs needed to correct defects in materials
or workmanship which would cause the vehicle not to meet these
standards for 5 years or 50,000 miles, whichever occurs first.
EMISSION SYSTEM PERFORMANCE WARRANTY (EXCEPT CALIFORNIA)
Covers all repairs, adjustments, or replacements if vehicle
has been maintained in accordance with the prescribed scheduled
maintenance instructions and fails to conform to applicable emission
standards and such failure results or will result in the vehicle owner
having to bear any penalty or other sanctions under local, state or

SC HED ULE D S ER VIC ES
1991 Mitsubishi Montero
1987-95 MAINTENANCE
Mitsubishi Maintenance & Service Intervals
Montero
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see
SEVERE SERVICE REQUIREMENTS (PERFORM W/SERVICE SCHEDULES)
for items requiring additional maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (AIR BAG)
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
Modifications or improper maintenance, including incorrect
removal and installation of the Supplemental Restraint System (SRS),
can adversely affect system performance. DO NOT cover, obstruct or
change the steering wheel horn pad in any way, as such action could
cause improper function of the system. Use only plain water when
cleaning the horn pad. Solvents or cleaners could adversely affect the
air bag cover and cause improper deployment of the system.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
AIR CONDITIONING SERVICING
WARNING: R-134a service equipment or vehicle A/C systems SHOULD NOT
be pressure tested or leak tested with compressed air. Some
mixtures of air/R134a have shown to be combustible at
elevated pressures. These mixtures are dangerous and may
cause fire and/or explosions. See the appropriate
A/C SYSTEM GENERAL SERVICING article in the AIR CONDITIONING
& HEAT section.