1991 MITSUBISHI MONTERO dip

install, reverse removal procedure using new gaskets and "O" rings.
Coat "O" ring with fuel before installation.
2) Install lower intake manifold gasket with adhesive side
toward intake manifold and gasket protrusions facing outboard of
engine. Tighten bolts and nuts to specification. See appropriate
TORQUE SPECIFICATIONS table at end of article. Check for fuel leaks.
TURBOCHARGER
Removal (Front)
1) Drain coolant, and remove radiator. Disconnect exhaust
pipe from turbo. Remove all air intake pipes. Note match marks and
installation depth on air pipes and hoses for reinstallation. Remove
serpentine drive belt. Remove alternator. Remove A/C compressor and
bracket, and support aside.
2) Remove O2 sensor. Remove dipstick assembly and turbo heat
shield. Disconnect turbo coolant feed and return lines. Disconnect
turbo oil feed and return lines. Remove turbocharger assembly.
Removal (Rear)
1) Drain coolant. Remove battery. Disconnect accelerator
cable at bracket and throttle body. Disconnect exhaust pipe from
turbo. Remove all air intake pipes and heat shields. Disconnect
accelerator cable at pedal.
2) Remove clutch booster vacuum hose. Remove O2 sensor.
Remove EGR pipe and turbo heat shield. Disconnect turbo coolant feed
and return lines. Disconnect turbo oil feed and return lines. Remove
turbocharger assembly.
CAUTION: DO NOT allow foreign material into turbocharger air intakes
or coolant and oil passages.
Inspection (Front & Rear)
1) Inspect turbocharger for oil leakage. Check turbine and
compressor wheels for cracks and other damage. Both wheels should turn
easily by hand.
2) Apply 6.8 psi (61 kPa) vacuum to wastegate diaphragm.
Ensure wastegate operates and diaphragm holds vacuum pressure. Use
care when cleaning gasket surfaces so no foreign material enters
turbocharger oil, coolant and air passages.
Installation (Front & Rear)
Refill turbocharger with clean engine oil through oil pipe
installation hole. To complete installation, reverse removal
procedure. Align match marks, and install air pipes and hoses to
proper depth.
EXHAUST MANIFOLDS
Removal (Montero & Pickup)
1) Remove splash shields. Remove O2 sensor. Remove exhaust
pipe-to-manifold nuts. Lower exhaust pipe, and remove gasket. Remove
heat protector. To remove right exhaust manifold, remove air duct,
engine lift bracket and alternator bracket.
2) To remove left exhaust manifold, remove EGR pipe and
gasket. Remove front intake manifold plenum bracket. Remove exhaust
manifolds and gaskets.
Inspection (Montero & Pickup)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. Check mounting surfaces of manifold
and cylinder head for warpage. Repair or replace components if warpage
exceeds .012" (.30 mm).

Installation (Montero & Pickup)
To install, reverse removal procedure using new gaskets.
Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS
(MONTERO & PICKUP) table at end of article.
Removal (3000GT)
1) Remove turbocharger(s) (if equipped). See TURBOCHARGER
under REMOVAL & INSTALLATION. On front manifold, remove serpentine
drive belt and alternator. Remove oil dipstick. On rear manifold,
remove EGR pipe (if equipped).
NOTE: Note locations and direction of installation of exhaust
manifold plain and spring washers for reinstallation
reference. DO NOT mix these fasteners.
2) On all manifolds, remove exhaust pipe-to-manifold nuts.
Lower exhaust pipe, and remove gasket. Remove heat protector. Remove
exhaust manifold nuts and washers. Note locations and direction of
installation of plain and spring washers for reinstallation reference.
DO NOT mix these fasteners. Remove exhaust manifold and gasket.
Inspection (3000GT)
Clean all gasket mating surfaces. Inspect for damage and
cracks on all mounting surfaces. Check mounting surfaces of manifold
and cylinder head for warpage. Repair or replace components if warpage
exceeds .012" (.30 mm).
Installation (3000GT)
To install, reverse removal procedure using new gaskets.
Install new "O" ring on dipstick guide. Coat "O" ring with oil before
installation. Install manifold nuts and washers in original locations.
Tighten nuts to specification in sequence. See Fig. 4. See TORQUE
SPECIFICATIONS (3000GT) table at end of article.
Fig. 4: Exhaust Manifold Tightening Sequence (3000GT)
Courtesy of Mitsubishi Motor Sales of America, Inc.
CYLINDER HEADS

surfaces. Resurface head if warpage exceeds specification. See
CYLINDER HEAD (SOHC) table under ENGINE SPECIFICATIONS at end of
article. Replace cylinder head if it is not within specification after
resurfacing.
Installation (SOHC)
1) Ensure mating surfaces are clean and dry. Note
identification mark located on front of head gasket. Identification
marks are: "R" for SOHC, "2DN" for DOHC non-turbocharged and "2DT" for
DOHC turbocharged engine. Install head gasket with identification mark
toward timing belt side of engine and facing upward. Ensure all holes
are aligned.
NOTE: Install head gasket with identification mark toward timing
belt side of engine and facing upward. Ensure all holes
align. Install washers on head bolts with chamfered side
toward bolt head.
2) Install cylinder head and bolts. Ensure washers are
installed on head bolts with chamfered side toward bolt head. Using
proper sequence, tighten bolts to specification in 2-3 steps. See
Fig. 5 . See appropriate TORQUE SPECIFICATIONS table at end of article.
3) Apply sealant to rocker cover sealing surfaces before
installation. See Fig. 6. Ensure rocker cover gasket projections are
aligned with notches in rocker cover. Coat all "O" rings with oil, and
install a new "O" ring on distributor adapter and oil dipstick tube.
4) Coat camshaft area with oil prior to installing
distributor adapter. To complete installation, reverse removal
procedure. Tighten bolts and nuts to specification. See appropriate
TORQUE SPECIFICATIONS table. After engine reaches normal operating
temperature, allow engine to cool, and retighten cylinder head bolts.
Fig. 6: Applying Sealant to Rocker Cover (SOHC)
Courtesy of Mitsubishi Motor Sales of America, Inc.
Removal (DOHC)
1) Drain cooling system. Remove upper and lower intake
manifolds and brackets. See UPPER INTAKE MANIFOLD and LOWER INTAKE
MANIFOLD under REMOVAL & INSTALLATION.
2) Remove turbocharger(s) (if equipped). See TURBOCHARGER
under REMOVAL & INSTALLATION. Remove heat shields from exhaust
manifolds. Remove exhaust manifolds. See EXHAUST MANIFOLDS under
REMOVAL & INSTALLATION.
3) Remove spark plug wires and ignition coils. Remove rocker
cover and gasket. Remove timing belt and timing belt inner covers. See

and moisture to a minimum.
CONNECTING LINES AND FITTINGS
A new gasket or "O" ring should be used in all instances when
connecting lines or fittings. Dip "O" ring in new refrigerant oil and
ensure it is not twisted during installation. Always use 2 wrenches to
prevent damage to lines and fittings.
PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, evacuate system thoroughly with a
vacuum pump. Charge system with proper amount of refrigerant and
perform a leak test. See REFRIGERANT OIL & R-12 SPECIFICATIONS chart
in this section for system capacities. Be sure to check all fittings
that have been opened. After system has been leak tested, make a
system performance check.
NOTE: Air conditioning systems will not normally need addition of
refrigerant oil unless definite oil loss has occurred due to
ruptured lines, leaking compressor seals, compressor
overhaul or component replacement.
ATSUGI ROTARY VANE DRAIN & REFILL
1) Before checking and adjusting oil level, operate
compressor at engine idling speed, with controls set for maximum
cooling and high blower speed, for 20 to 30 minutes to return oil to
compressor.
2) Stop engine, discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS at beginning of article. Drain
compressor oil from compressor discharge port and measure the amount.
Oil is sometimes hard to drain when compressor is cool. Remove oil
while compressor is warm.
3) If the amount drained is less than 3 ounces, conduct leak
tests at system connections, and if necessary, repair or replace
faulty parts. Check purity of oil and adjust oil level as follows.
4) If amount drained was above 3 ounces, oil level is right.
Pour in same amount as was drained. If amount drained was below 3
ounces, pour in 3 ounces of new refrigerant oil.
BOSCH 6-CYL DRAIN & REFILL
1) Before checking and adjusting oil level, operate
compressor at engine idling speed, with controls set for maximum
cooling and high blower speed, for 20 to 30 minutes to return oil to
compressor.
2) Stop engine and discharge refrigerant. Remove refrigerant
oil level inspection plug on side of compressor. Oil should be at
lower lip of threaded hole. Add necessary new refrigerant oil (if
low). Replace inspection plug and tighten to 10-12 ft. lbs. (14-16 N.
m).
CALSONIC V5 5-CYLINDER
1) Before checking and adjusting oil level, operate
compressor at 1000-1500 engine RPM, and set controls at maximum
cooling and blowing speed for 20-30 minutes to return oil to

mounting bolts. Rotate compressor in brackets until filler plug is at
top. Clean area around filler plug and remove plug slowly. Rotate
front hub plate so notch in lobe is 110 degrees from the bottom. This
rotates ball end of top piston to align with oil fill port and allows
clearance for dipstick. See Fig. 1.
2) Insert compressor dipstick diagonally from right to left
until stop on dipstick contacts filler plug surface. Remove dipstick
and note oil fill level. Each increment on dipstick represents one
ounce of oil. Add oil if necessary to reach 3-4 ounce level.
Fig. 1: Sanden 5-Cylinder Oil Level Checking
Courtesy of Sanden International U.S.A, Inc.
SANDEN 7-CYL DRAIN & REFILL
1) Before checking and adjusting oil level, operate
compressor at engine idle speed, and set controls at maximum cooling
and high blowing speed for 20-30 minutes to return oil to compressor.
2) Stop engine. Discharge refrigerant and remove compressor
from vehicle. See SERVICING PRECAUTIONS at the beginning of this
article. Remove oil drain plug and drain oil. Measure amount of oil
drained. Install drain plug with new "O" ring.
3) If amount drained is more than 3 ounces, fill with same
amount using new oil. If amount drained is less than 3 ounces, fill
with 3 ounces. Install filler plug. Install compressor and recharge
system.

immediately before connections are made. This will keep entry of air
and moisture to a minimum.
CONNECTING LINES AND FITTINGS
A new gasket or "O" ring should be used in all instances when
connecting lines or fittings. Dip "O" ring in new refrigerant oil and
ensure it is not twisted during installation. Always use 2 wrenches to
prevent damage to lines and fittings.
PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, evacuate system thoroughly with a
vacuum pump. Charge system with proper amount of refrigerant and
perform a leak test. See REFRIGERANT OIL & R-12 SPECIFICATIONS chart
in this section for system capacities. Be sure to check all fittings
that have been opened. After system has been leak tested, make a
system performance check.
NOTE: Air conditioning systems will not normally need addition of
refrigerant oil unless definite oil loss has occurred due to
ruptured lines, leaking compressor seals, compressor
overhaul or component replacement.
ATSUGI ROTARY VANE CLUTCH R & I
Removal
When replacing compressor clutch, be careful not to scratch
shaft or bend pulley. When removing center bolt, hold clutch disc with
Clutch Holder (KV99231010). Using Hub Puller (KV998VR001 &
KV99231010), remove clutch disc. When removing pulley, remove lock nut
with Hub Socket (KV99235160).
Installation
Wipe oil off clutch surface. Adjust disc pulley clearance to
.012-.024" (.3-.6 mm). Tighten center bolt to 80-104 INCH lbs. (9.1-
11.8 N.m). Tighten clutch lock nut to 22-29 ft. lbs. (29-39 N.m). See\
Fig. 1 .
Fig. 1: Atsugi Rotary Vane Compressor
Courtesy of Nissan Motor Co., U.S.A.
BOSCH 6-CYL CLUTCH R & I

against crankshaft shoulder. Use Thin Wall Socket (J-9399) and Clutch
Hub Holder (J-25030). Tighten shaft nut to 96-192 INCH lbs.
(11-22 N.m). Spin pulley rotor by hand to ensure rotor is not rubbing
on clutch drive plate. See Fig. 8.
HARRISON V5 5-CYLINDER SHAFT SEAL R & I
Removal
Discharge refrigerant from system using approved refrigerant
recovery/recycling equipment. See SERVICING PRECAUTIONS at beginning
of article. Remove clutch plate assembly. Remove shaft seal snap ring.
Thoroughly clean inside of compressor neck area around shaft and seal.
Engage tangs of Seal Remover/Installer (J-23128-A) into recessed
portion of seal and remove seal. Remove and discard seal "O" ring from
compressor neck. Thoroughly clean inside of compressor neck and "O"
ring groove.
Installation
1) Coat new "O" ring with refrigerant oil and install on "O"
ring installer (J-33011). Install "O" ring into groove in compressor
neck. Attach new seal to Seal Remover/Installer (J-23128-A). Dip seal
in clean refrigerant oil.
2) Place Seal Protector (J-34614) over compressor shaft. Pus\
h
new seal over shaft protector. Install new snap ring with flat side
against seal. Install clutch plate assembly.
Fig. 8: Exploded View of Harrison V5 5-Cylinder Compressor
Courtesy of General Motors Co.

SANDEN 5-CYL CLUTCH R & I
Removal
1) Hold clutch hub stationary and remove shaft nut. Remove
clutch plate using puller. Remove external front housing snap ring and
internal bearing snap ring. See Fig. 16.
2) Install puller and pull rotor assembly off. remove 3
screws and clutch coil. Use driver and hammer to drive bearing out
from hub.
Installation
1) Install new bearing; ensure installer contacts outer race
of bearing. Install snap ring and ensure bearing turns freely. Install
clutch coil on compressor.
2) Support compressor on rear mounting ears. Align rotor on
front housing hub. Use adapter and press to install rotor (or drive
into place with soft mallet). After rotor is seated, install front
snap ring.
SANDEN 5-CYL SHAFT SEAL R & I
NOTE: Check compressor refrigerant oil level when replacing seals.
Removal
1) Hold clutch hub stationary and remove shaft nut with thin
wall socket. Use clutch plate puller to remove clutch plate. Tap key
out of slot in crankshaft.
2) Remove seal retainer with seal remover and 3/4" socket
wrench. Use seal seat remover tongs to pull seal seat off compressor
shaft. Insert seal remover into front housing and turn to engage tangs
on seal. Lift seal out. Remove seal "O" ring from front housing, being
careful not to scratch shaft.
Installation
1) Coat "O" ring with refrigerant oil and install into
groove. Load a new seal onto installer, being careful not to touch
carbon sealing surface with fingers. Install shaft protector. Dip seal
in refrigerant oil and install on shaft. Rotate seal clockwise until
seal fits into flats on shaft. Remove seal installer by turning
counterclockwise.
2) Coat seal seat with refrigerant oil and install with
tongs. Reinstall seal seat retainer (with flat side down). Install
shims and shaft key. Rotate shaft several times to help break in seal.
3) Use a press to install clutch plate. Make sure that air
gap is .016-.031" (.41-.79 mm). Hold plate stationary and install
shaft nut.