1991 MITSUBISHI MONTERO tires

\003
AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS

1991 M it s u bis h i M onte ro
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85C for 2 hours is generally considered a
maximum limit).

SHOE HARDWARE
SHOES
SOCKETS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
STEEL BRAKE LINES
STOPLIGHT SWITCHES
SWITCHES
TIRES
TOOTHED RINGS (TONE WHEEL)
VACUUM BOOSTERS
VACUUM HOSES
VALVES
WHEEL ATTACHING HARDWARE
WHEEL BEARINGS, RACES AND SEALS
WHEEL CYLINDERS
WIRING HARNESSES
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt:\
1) a Pledge of Assurance to their Customers and
2) the Motorist Assurance Program Standards of Service.
All participating service providers have agreed to subscribe
to this Pledge and to adhere to the promulgated Standards of Service
demonstrating to their customers that they are serious about customer
satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
are continually re-published. In addition to these, standards for
Drive Train and Transmissions have recently been promulgated.
Participating shops utilize these Uniform Inspection & Communication
Standards as part of the inspection process and for communicating
their findings to their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not

Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding, affecting
performance ............ A .. Require repair or replacement.
Binding, not affecting
performance ............ 2 .. Suggest repair or replacement.
Broken .................. A .. Require repair or replacement.
Burned, affecting
performance ............ A ........... (1) Require repair or
replacement.
Burned, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............ 1 .. Suggest repair or replacement.
Float saturated ......... A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Malfunctioning .......... A ........... ( 2) Require repair or
replacement.
Melted, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Melted, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Missing ................. C ............ Require replacement.
Out of adjustment ....... B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Won't return ............ A .. Require repair or replacement.
Worn .................... 1 ............ Suggest replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Includes inoperative, intermittent operation, or failure to
perform all functions.









\









\









\









\









\









\









\


TIRES
Consult the vehicle owner's manual or vehicle placard for
correct size, speed ratings, and inflation pressure of the original
tires.
TIRE INSPECTION

1994-96 (3.0L DOHC & 3.5L) .................. 9.0 Qts. (8.5L)
Cooling System
1983-88 ..................................... 8.5 Qts. (8.0L)
1989-96
2.6L ....................................... 9.7 Qts. (9.2L)
3.0L ...................................... 10.0 Qts. (9.5L)
3.5L ...................................... 10.0 Qts. (9.5L)
Differential
1983-88 ..................................... 1.9 Qts. (1.8L)
1989-93
2.6L ....................................... 1.9 Qts. (1.8L)
3.0L ....................................... 2.7 Qts. (2.6L)
1994-96
3.0L & 3.5L ................................ 2.7 Qts. (2.6L)
Engine Oil
1983-86 ..................................... 6.0 Qts. (5.8L)
1987 ........................................ 5.2 Qts. (5.0L)
1988 ........................................ 5.0 Qts. (4.8L)
1989-91 ..................................... 5.5 Qts. (5.3L)
1992-96 ..................................... 5.2 Qts. (4.9L)
Power Steering ................................ 1.1 Qts. (1.0L)
Fuel Tank
1983-88 .................................... 15.9 Gals. (60L)
1989-90
2.6L 2-Door ............................... 15.9 Gals. (60L)
3.0L 2-Door ............................... 19.9 Gals. (75L)
2.6L & 3.0L 4-Door .......................... 24 Gals. (92L)
1991-96 ...................................... 24 Gals. (92L)
Manual Transmission
1983-91 ..................................... 2.3 Qts. (2.2L)
1992 ........................................ 2.4 Qts. (2.3L)
1993-96 ..................................... 2.6 Qts. (2.5L)
Transfer Case
1983-91 ..................................... 2.3 Qts. (2.2L)
1992-96 ..................................... 2.4 Qts. (2.3L)
(1) - Use of R12 in a R134a system will result in SEVERE DAMAGE.
( 2) - 1983 model equipped with manual transmission only.









\









\









\









\









\









\









\



WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE









\









\









\









\









\









\







Wheel Size Tire Size
1983-86
15 x 6JJ (Steel) .............................. 215 SR15
1987-88

2.6L Engine ........................................... 45
2.6L Optional ......................................... 45
3.0L V6 ........................................... (1) 24
3.5L V6 ........................................... ( 1) 24
( 1) - Check hood clearance on 1986 and newer models.









\









\









\









\









\









\







CAUTIONS & WARNINGS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIR BAG SYSTEM
NOTE: See the AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT Section.
The SRS has no user-servicable parts. Always have servicing
done by an authorized dealer.
When performing maintenance on air bag equipped vehicles
always observe proper safety precautions.
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all warnings and service precautions. See
appropriate AIR BAG RESTRAINT SYSTEM article in the
ACCESSORIES/SAFETY EQUIPMENT section.
CAUTION: Disconnect negative battery cable before servicing any air
bag system, steering column or passenger side dash
component. After any repair, turn ignition key to the ON
position from passenger's side of vehicle in case of
accidental air bag inflation
ANTI-LOCK BRAKE SYSTEM (ABS)
CAUTION: Never mix different diameter tires. On loose or uneven
surfaces, the ABS system may require longer stopping
distances than conventional brake systems. Exercise caution
when removing mud or snow from the wheels so as not to
damage the ABS wiring or speed sensors.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BRAKE PAD WEAR INDICATOR
Indicator will cause a squealing or scraping noise, warning
that brake pads need replacement.

\003
PR E-A LIG NM EN T C HEC KS

1991 M it s u bis h i M onte ro
Wheel Alignment
PRE-ALIGNMENT INSPECTION PROCEDURES
PRE-ALIGNMENT CHECKS
Before making wheel alignment adjustment, perform the
following checks:
1) Tires should be equal in size and runout must not be
excessive. Tires and wheels should be in balance, and inflated to
manufacturer's specifications.
2) Wheel bearings must be properly adjusted. Steering linkage
and suspension must not have excessive looseness. Check for wear in
tie rod ends and ball joints.
3) Steering gear box must not have excessive play. Check and
adjust to manufacturer's specifications.
4) Vehicle must be at curb height with full fuel load and
spare tire in vehicle. No extra load should be on vehicle.
5) Vehicle must be level with floor and with suspension
settled. Jounce front and rear of vehicle several times and allow it
to settle to normal curb height.
6) If steering wheel is not centered with front wheels in
straight-ahead position, correct by shortening one tie rod adjusting
sleeve and lengthening opposite sleeve equal amounts.
7) Ensure wheel lug nuts are tightened to torque
specifications.

RID IN G H EIG HT A D JU STM EN T

1991 M it s u bis h i M onte ro
1991-92 WHEEL ALIGNMENT
Riding Height Adjustment
Chrysler Motors: Ram-50
Mitsubishi: Montero, Pickup
RIDING HEIGHT ADJUSTMENT
Before adjusting alignment, check riding height. Ensure
vehicle is on level floor and tires are properly inflated. Bounce
vehicle several times and allow suspension to settle.
Visually inspect vehicle, from front to rear or side to
side, for signs of abnormal height. Remove extra heavy items from
passenger and luggage compartments. If riding height is not within
specification, check and repair suspension before adjusting alignment.
See RIDING HEIGHT SPECIFICATIONS (FRONT) table.
RIDING HEIGHT SPECIFICATIONS (FRONT) ( 1)









\









\









\









\









\





Application (2) In. (mm)
Montero ............................ 2.80 (71.1)
Pickup 4WD & Ram-50 4WD ............ 3.07 (78.0)
(1) - Ensure tire inflation is correct and vehicle
is level.
( 2) - Distance between lower control bump stopper
and bracket. See Fig. 1.









\









\









\









\









\





RIDING HEIGHT SPECIFICATIONS 1992 (FRONT) ( 1)








\









\









\









\









\





Application In. (mm)
Montero .................. 0.83-0.91 (21.0-23.0)
Pickup 4WD & Ram-50 4WD ............ 3.11 (79.0)
(1) - Distance between lower control bumper and
bracket.









\









\









\









\









\





Fig. 1: Measuring Front Riding Height (Typical 4WD)
Courtesy of Mitsubishi Motor Sales of America.

WARNING: Avoid breathing R-134a refrigerant and PAG lubricant vapors,
exposure may irritate eyes, nose and throat. To remove
R-134a from system use R-134a recycling equipment that meets
SAE J2210 specifications. If accidental system discharge
occurs, ventilate work area before resuming service.
ANTI-LOCK BRAKE SYSTEM
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
REPLACING BLOWN FUSES
Before replacing a blown fuse, remove ignition key, turn off
all lights and accessories to avoid damaging the electrical system. Be
sure to use fuse with the correct indicated amperage rating. The use
of an incorrect amperage rating fuse may result in a dangerous
electrical system overload.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
computers may lose memory data. When battery power is
restored, driveability problems may exist on some vehicles.
These vehicles may require a relearn procedure. See
appropriate COMPUTER RELEARN PROCEDURES article in the
GENERAL INFORMATION section below.
BRAKE FLUID
For vehicles equipped with a traction control system, idle
engine while pouring brake fluid into reservoir.
CATALYTIC CONVERTER
Continued operation of vehicle with a severe malfunction
could cause converter to overheat, resulting in possible damage to
converter and vehicle.
ELECTROSTATIC DISCHARGE SENSITIVE (ESD) PARTS
WARNING: Many solid state electrical components can be damaged by
static electricity (ESD). Some will display a warning label,
but many will not. Discharge personal static electricity by