1991 MITSUBISHI ECLIPSE torque specification

[x] Cancel search: torque specification

tow bar climate control clock setting fuel pump park assist cabin filter

Load previous 8 pages

Page 853 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual AUTOMATIC TRANSAXLE - Specifications
SPECIFICATIONS
-+ GENERAL SPECIFICATIONSl@lCA.CItems
TypeTorque converter
TypeEngine stall speed
Stall speed ratio
Transaxle
TypeGear ratio
First
Second
Third
Four

Page 854 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual 21-160AUTOMATIC TRANSAXLE - Specifidons
ItemsOutput flange bearing end play <F4A33,
W4A33> mm (in.)
Front clutch end play
<F4A22>mm, (in.)Rear clutch end play
<F4A22>mm (in.)
End clutch end play
<

21-160AUTOMATIC TRANSAXLE - Specifidons
ItemsOutput flange bearing end play W4A33> mm (in.)
Front clutch end play
mm, (in.)Rear clutch end play
mm (in.)
End clutch end play
mm (in.)
Front clutch end play mm (in.)
Rear clutch end play mm (in.)
End clutch end play W4A33>mm (in.)
Transfer idler gear preload
Nm (ft.lbs.)Center differential side gear end play
mm (in.)
Front output shaft end play
mm (in.)
Transfer
Drive bevel gear starting torque
Driven bevel gear starting torque
Bevel gear backlashNm
(ft.lbs.)Nm
(ft.lbs.)mm (in.)
IALVE BODY SPRING IDENTIFICATION CHARTPart name
Regulator valve spring
l-2 shift valve spring
Pressure control valve spring
Rear clutch exhaust valve spring
End clutch valve spring
2-3 shift valve spring
N-R control valve spring
Reducing valve spring
Line relief spring
Torque converter valve spring
Shift control valve spring
FFyl;;;lutch control valve spring
SPACER SETWire diameter
mm (in.)
1.4 (055)
0.6 (024)
0.45 (0177)
0.7 (028)
0.6
(.024)0.8
(.031)0.7 (028)
1.2 (047)
1.0 l.039)
1.3 (051)
0.5 (020)
0.7
(.028)Outside dia.
mm (in.)
15i.59)
7.6
t.299)
7.6(.299)
6.8(.268)
6.6(260)
7.0(276)
9.2(.362)
8.9(350)
7.0(276)
9.0(.354)
5.7(224)
6.2(.244)
IPart name
Spacer set
(for adjustment of input shaft end play)Specifications
o-0.09 (d-.0035); . ,i f 1, ,i’.” :,li
0.7-0.9 (.028-.035)
0.4-0.6 (.016-.024)
0.4-0.65 (.016-.026)
0.8-I .O (.032-.039)
1.0-I .2 (.039-.047)
0.60-0.85 (.024-.034)
0.8
(1)
0.01-0.03 (.0004-.0012)
0.055-0.115 (.0022-.0045)
1.7-2.5 (1.23-1.81)
1.0-I .7 (0.72- 1.23)
0.08-0.13 (.0031-.0051)
Lengthmm (in.)
52 (2.05)
26.6 (1.047)
21.3
(.839)27.4 (1.079)
24.4
(.961)27.5 (1.883)
32.1 (1.264)
29.5 (1.161)
17.3
(.681)22.6
i.890)26.8 (1.055)
14.2
(.559)No. of turns
11.5
13.5
8.5
12.5
15.5
15.5
‘4
8.5
’-*12.5
10
9.5
’22
9.5I
Thicknessmm (in.) Part No. “’
1.4(055).1.0l.040)MD997854
1.4(.055),
1.2(047)MD997847
’1.8(.071),
1.4l.055)MD997848::!1.8
(.071), 1.6 (.063)fQlD997849 ” .’
2.2(.087),
1.8(.071)MD997850
2.2(.087),2.0(.079)MD997851h2.6(.102),2.2(.087)MD997852“-2.6(.102),2.4i.095)M D997853

Page 860 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual 21-166AUTOMATIC TRANSAXLE - SDecifications
TORQUE SPECIFICATIONS,. _ ,,,_ .Nglcc-
ItemsTie rod end to knuckle
Lower arm ball joint to knuckle
Transaxle mounting bracket to transaxle
Special bolts
Sele

Page 896 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual 21-202AUTOMATIC TRANSAXLE - Troubleshooting
CONVERTER STALL TESTStall test consist of determining maximum engine
speed obtained at full throttle in “D” and “R”
positions. This test checks torq

21-202AUTOMATIC TRANSAXLE - Troubleshooting
CONVERTER STALL TESTStall test consist of determining maximum engine
speed obtained at full throttle in “D” and “R”
positions. This test checks torque converter stator
overrunning clutch operation, and holding ability of
transaxle clutches and low-reserve brake.
CautionDuring this test, make sure that no one stand in
front of or behind vehicle.
1. Check transaxle fluid level. Fluid should be at
normal operating temperature
[70-80°C (160-
18O”F)]. Engine coolant should also be at normaloperating temperature
[80-90°C (180- 19O”F)l.2. Apply chocks to both rear wheels.
3. Attach engine tachometer.
4. Apply parking and service brakes fully.
5. Start engine.
6. With selector lever in “D” position, depress
accelerator pedal fully to read engine maximum
rpm. Do not hold throttle wide open any longer
than is necessary to obtain maximum engine
rpm reading, and never longer than 5 seconds ata time. If more than one stall test is required,
operate engine at approximatey 1,000 rpm in
neutral for 2 minutes to cool transaxle fluid
between tests.
Stall speed:
1,800-3,200 rpm
TRANSAXLE CONTROL7. Place selector lever to “R” position and perform
?+stall test by the same procedure as in foregoing
-,
item.Stall Speed Above Specification in “D”
If stall speed is higher than specification, rear clutchor overrunning clutch of transaxle is slipping. In this
case, perform hydraulic test to locate cause of
slippage.Stall Speed Above Specifjcation in “R”
If stall speed is higher than specification, front
clutch of transaxle or low-reverse brake is slipping.
In this case, perform hydraulic test to locate cause
of slippage.
Stall Speed Below Specification in “D” and “R”
If stall speed is lower than specification, insufficient
engine output or faulty torque converter is sus-
pected. Check for engine misfiring, ignition timing,
valve clearance etc. If these are good, torque
converter is faulty.
Symptom
Selector lever operation isstiff
Probable causeIncorrect adjustment of sleeve
Incorrect adjustment of control cable
Excessive wear of detent plate
Worn contact surfaces of pushbutton and sleeveRemedyAdjust
Replace
Starter motor does notoperate with the selector
lever in the “N” or
“P”position
Will not shift to
4-speedMalfunction in inhibitor switch
Malfunction of starter relay
Incorrect adjustment of control cableMalfunction of OD switch
Replace
Adjust
Replace

Page 1039 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual 22-l-.
WHEELS
AND TIRES
CONTENTSNZZAA-
SERVICE ADJUSTMENT PROCEDURES.......4TROUBLESHOOTING......................................3
Tire
InflationPressureCheck......................4Bald Spots
TireWear

Page 1040 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual 5 22-2WHEELS AND TIRES - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONSN22CA- @NVehicles with
~eDhL”~~HWCthEngineVehicles withVehicles withItems1.8L Engine2.0L DOHC Engine 2.0L DOHC Engine<No

Page 1045 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual 23-lBODY
CONTENTSN23Ak-
AERO PARTS..........................................74
CENTRAL DOOR LOCKING SYSTEM...........70
DOOR ASSEMBLY....................................63
DOOR GLASS AND REGULATOR....

23-lBODY
CONTENTSN23Ak-
AERO PARTS..........................................74
CENTRAL DOOR LOCKING SYSTEM...........70
DOOR ASSEMBLY....................................63
DOOR GLASS AND REGULATOR................66
DOORHANDLEANDLATCH.....................69
DOOR MIRROR........................................72
DOOR MOULDING AND
DRIP LINE WEATHERSTRIP........................72
....DOOR RUNCHANNEL...............................71
DOOR TRIM AND WATERPROOF FILM........65
ELECTRIC REMOTE CONTROLLED
MIRROR SWITCH.....................................73
FENDER..................................................51
FLOOR CONSOLE....................................84
FRONT BUMPER......................................39
FRONT SEAT..........................................90
FUEL TANKFILLERDOOR.........................38
GARNISHES............................................47
HEADLINING...........................................89
HOOD....................................................34
INSTRUMENT PANEL................................79
LIFTGATE...............................................36
LIFTGATE WINDOWGLASS......................62
LOOSE PANEL.........................................53
MOULDING.............................................48
POWER WINDOW....................................67
QUARTERWINDOWGLASS......................61
REAR BUMPER........................................43
REAR SEAT............................................93
SEAT BELT.............................................94
SERVICE ADJUSTMENT PROCEDURES........31
Door Adjustment....................................32
Door Glass Adjustment............................32Door Inside Handle Play Check..................
32
Door Outside Handle Play Check................32
Floor PanInspection...............................
33Fuel Filler Door Adjustment.......................
31
Hood Adjustment...................................31
Liftgate Adjustment.................................31
Water Test...........................................33
SPECIAL TOOLS......................................5
SPECIFICATIONS.....................................2
General Specifications..............................
2
Lubricants.............................................5
Sealants and Adhesives...........................5
Service Specifications..............................3
Torque Specifications..............................3
SUNROOF...............................................77TRIMS
....................................................85
TROUBLESHOOTING................................6WINDOW
GLASS.....................................54
WINDSHIELD...........................................58

Page 1047 of 1216

MITSUBISHI ECLIPSE 1991 Service Manual BODY - Specifications23-3
Items
Door lock control unitEffective voltage
V
Current consumption (when not in operation)
Door lock power relay
Range of voltage used
V
Rated load current (at 13.5 VIA
Rat

Load next 8 pages

Page: < prev 1-10 ... 9-16 17-24 25-32 33-40 41-48 49-56 next >

fuel tank capacity set clock snow chains washer fluid ABS isofix