1991 MITSUBISHI 3000GT wheel bolts

GENERAL - How to Use This Manual00-3HOW TO USE THIS MANUAL
MOOBAAF
c;SCOPE OF MAINTENANCE, REPAIR AND
DEFINITION OF TERMS
SERVICING EXPLANATIONSSTANDARD VALUE
bThis manual provides explanations, etc. concerning
procedures for the inspection, maintenance, repair
and servicing of the subject model. Unless other-
wise specified, each service procedure covers all
models. Procedures covering specific models are
identified by the model codes, or similar designation
(engine type, transaxle type, etc.). A description of
these designations is covered in this unit under
“VEHICLE IDENTIFICATION”.
SERVICE ADJUSTMENT PROCEDURES“Service Adjustment Procedures” are procedures
for performing inspections and adjustments of
particularly important locations with regard to the
construction and for maintenance and servicing, but
other inspections (for looseness, play, cracking,
damage, etc.) must also be performed.
SERVICE PROCEDURESThe service steps are arranged in numerical order
and attentions to be paid in performing vehicle
service are described in detail in SERVICE POINTS.
TROUBLESHOOTING
Troubleshootings are classified into master trouble-
shooting and group troubleshooting and located as
follows:
The master troubleshooting is prepared when the
trouble symptom relates to two or more groups and
given in MASTER TROUBLESHOOTING.
The group troubleshooting guide is prepared for
causes of problems related to that individual groupIndicates the value used as the standard for judging
the quality of a part or assembly on inspection or the
value to which the part or assembly is corrected and
adjusted. It is given by tolerance.
LIMITShows the standard for judging the quality of a part
or assembly on inspection and means the maximum
or minimum value within which the part or assembly
must be kept functionally or in strength. It is a value
established outside the range of standard value.
REFERENCE VALUEIndicates the adjustment value prior to starting the
work (presented in order to facilitate assembly and
adjustment procedures, and so they can be com-
pleted in a shorter time).
CAUTIONIndicates the presentation of information particularly
vital to the worker during the performance of
maintenance’ and servicing procedures in order to
avoid the possibility of injury to the worker; or
damage to component
.parts, or a reduction of
component or vehicle function or performance, etc.
INDICATION OF TIGHTENING TORQUEThe tightening torque shown in this manual is a
basic value with a tolerance of
+lO% except the
following cases when the upper and lower limits of
tightening torque are given.
(1) The tolerance for the basic value is within
+ I no/-
only; a troubleshooting guide is prepared for eachI iv,“.appropriate group.(2) Special bolts or the like are in use.
(3) Special tighteningmethods are used.
MODEL INDICATIONS
The following abbreviations are used in this manual for classification of model types.M/T:Indicates the manual transaxle, or models equipped with the manual transaxle.
A/T:Indicates the automatic transaxle, or models equipped with the automatic transaxle.
MPI: Indicates the multi-point injection, or engines equipped with the multi-point injection.
Turbo: Indicates an engine with turbocharger, or a model equipped with such an engine.
Non-Turbo: Indicates an engine without turbocharger, or a model equipped with such an engine.
FWD: Indicates the front wheel drive vehicles.
AWD; Indicates the all wheel drive vehicles.
ABS:Indicates the anti-lock braking system or models equipped with the anti-lock braking system.
ECS: Indicates the electronic control suspension or models equipped with the electronic control
suspension.
4WS:Indicates the 4-wheel steering system or models .equipped with the 4-wheel steering system.
TSB Revision

11-52ENGINE - Crankshaft, Flywheel and Drive Plate
9. INSTALLATION OF BEARING CAP
(1) Attach the bearing cap on the cylinder block as shown in
the illustration.
(2) Tighten the bearing cap bolts to the specified torque in‘I
the sequence shown in the illustration.
J ~
(3) Check that the crankshaft rotates smoothly.
Cral
Bearing cap
\Bearing cap bolt
Front of engine
(Timing belt side)
7EN270(4) Check the end plate. If it exceeds the limit value,
replace the thrust bearing.
Standard value: 0.05
- 0.25 mm (.0020 - .0098 in.)
Limit: 0.3 mm
(.012 in.)
-rent ofengineTimingIelt side)
8.
LLiN03,ij
1 TSB RevisionINSTALLATION OF BEARING CAP STAY
(1) Apply engine oil to the thread and bearing surface of
each bolt.
(2) Temporarily tighten the bolts on the cylinder block side.(3) Tighten the bolts on the bearing cap side to specified
torque.(4) Finally, tighten the bolts on the cylinder block side to
specified torque.
NOTEThe bearing cap stays A and B differ in shape. Install
correct ones on correct sides.d

CLUTCH - Clutch Cover and Disc
6CLOl f
Lubricant: MITSUBISHI genuine grease
Part No. 0101011 or equivalent
7CLOOO8
Lubricant: MITSUBISHI genuine grease
Part No. 0101011 or eauivalent
6CL03:
Lubricant: MITSUBISHI genuine greasePart No. 0101011 or equivalent
SERVICE POINTS OF REMOVALMZlGBAK
1.REMOVAL OF CLUTCH COVER ASSEMBLY / 2. CLUTCH
DISCDiagonally loosen bolts which attach clutch cover to
flywheel. Back off bolts in succession, one or two turns at a
time, to avoid bending cover flange.
CautionDO NOT clean clutch disc or release bearing with
d
cleaning solvent.TSB Revision
1

21-22CLUTCH - Clutch Cover and Disc
APPLYgrease
6CLOlE
lir#LClutch disc
Clutch cover
assembly
v-l6CL02EITSB Revision
SERVICE POINTS OF INSTALLATIONMZIGDAU5. APPLICATION OF GREASE TO RELEASE FORK
(1) Apply a coating of the specified grease to the point of
contact with the fulcrum and the point of contact
withthe release bearing.
Specified grease: MITSUBISHI genuine grease
Part No. 0101011 or equivalent
CautionWhen installing the clutch, apply grease to each
part, but be careful not to apply excessive grease;excessive grease will cause clutch slippage and
shudder.(2) Apply a coating of the specified grease to the end of the
release cylinder’s push rod and to the push rod hole in
the release fork.
Specified grease: MITSUBISHI genuine grease
Part No. 0101011 or equivalent
4.APPLICATION OF GREASE TO CLUTCH RELEASE BEAR-ING (FWD)
Pack the inner surface of the clutch release bearing and the
groove with the specified grease.
Specified grease: MITSUBISHI genuine grease
Part No. 0101011 or equivalent
2. APPLICATION OF GREASE TO CLUTCH DISC
/ 1.
CLUTCH COVER ASSEMBLY
(1) Apply a coating of the specified grease to the clutch
disc spline, and then use a brush to rub it in.
Specified grease: MITSUBISHI genuine grease
Part No. 0101011 or equivalent
(2) Using the universal clutch disc aligner, position the
clutch disc to the flywheel.
(3) Install the clutch cover assembly. Tighten the bolts a
little at a time, working in a diagonal sequence, finally
tightening them to the specified torque.I

FRONT AXLE - Hub and Knuckle26-7MB990998-01MB990635-01
II
I1 lA0286 1
SERVICE POINTS OF REMOVALM2618AH
1. DISCONNECTION OF FRONT SPEED SENSORRemove the mounting bolts which hold the speed sensor
bracket to the knuckle, and then remove the speed sensor.
Caution
Be careful when handling the pole piece at the tip of the
speed sensor and the toothed edge of the rotor so asnot to damage them by striking against other parts.
3. REMOVAL OF DRIVE SHAFT NUT
Loosen the drive shaft nut while the vehicle is on the floor
with the brakes applied.
Caution
Do not apply vehicle load to the wheel bearing loosingthe drive shaft nut. If, however, vehicle load must be
applied to the bearing in moving the vehicle, temporari-
ly secure the wheel bearing by using the special tools,
MB990998-01, etc.
4. REMOVAL OF CALIPER ASSEMBLY
Remove the caliper assembly and suspend it with wires.
8. DISCONNECTION OF LOWER ARM BALL JOINT
Using the special tool, disconnect the lower arm ball joint
from the knuckle.
Caution1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
IO. DISCONNECTION OF TIE ROD ENDUsing the special tool, disconnect the tie rod end from the
knuckle.
Caution
1. Be sure to tie the cord of the special tool to the
nearby part.2. Loosen the nut but do not remove it.
11. REMOVAL OF DRIVE SHAFTUse the special tool to push out the drive shaft from the
front hub.
14. REMOVAL OF HUBIn the case of AWD-vehicles with A.B.S., take care not to
damage the rotor for A.B.S. installed to the B.J. outer race
when removing the hub.
TSB Revision

REAR SUSPENSION - Service Adjustment Procedures34-5
0 camber
“\
er
ewer arm (L.H.)A-L!?., ’ cLr”“l‘412F002E
SERVICE ADJUSTMENT PROCEDURES
REAR WHEEL ALIGNMENT INSPECTIONM34FAAH
CAMBERStandard value: 0” + 30
To adjust camber, turn the lower arm mounting bolt
(cross-
member side).
NOTE(1) Make the adjustment with the assist link mounting bolt
(crossmember side) loosened.
(2) The difference between the right and left wheels should be30’ or less.
(3) Left wheel: Clockwise
(0 camber)
Right wheel: Clockwise
(0 camber)
One graduation changes camber by about 15’.
TOE-INStandard value: 0.5
-+ 2.5 mm (.Ol + .09 in.)
To adjust toe, turn the assist link mounting bolts (on crossmem-ber side) on both sides
t,he same amount.
NOTE
(1) The difference between right and left wheels should be 3mm (.I2 in.) or less.
(2) Left wheel: Clockwise (toe-in)
Right wheel: Clockwise (toe-out)
One graduation changes toe by about 4.8 mm
(.19 in.)
.
Caution1. Adjust the eccentric bolt within 90” from the central
position.
2.Adjust camber and toe, in that order, and, if camber isadjusted, be sure to adjust toe also.
TSB Revision

REAR SUSPENSION - Service Adjustment Procedures34-23
SERVICE ADJUSTMENT PROCEDURES
REAR WHEEL ALIGNMENT INSPECTIONM34FDACCAMBER
Standard value:
-0”lO’ + 30’
To adjust camber, turn the lower arm mounting bolt on the
crossmember side.
NOTE
12FOO21Left wheel: Clockwise (0 camber)
Right wheel: Clockwise
(0 camber)
The difference between the right and left wheels
shoiuld be 30’
or less.
One graduation changes camber by about 12’.
\Trailing arm (L.H.)
\\12A0083
17FllO75TOE-IN
Standard value: 0.5
-t 2.5 mm (.Ol + .09 in.)
To adjust toe, turn the trailing arm mounting bolts on the
crossmember side on both sides the same amount.
NOTELeft wheel: Clockwise (toe-in)
Right wheel: Clockwise (toe-out)
The difference between right and left wheels should be 3 mm
(.12 in.) or less.
One graduation changes toe by about 2 mm
(.08 in.).
Caution
1. Adjust the eccentric cam bolt within 90” from’ the
central position.
2.Adjust camber and toe, in that order, and, if camber is
adjusted, be sure to adjust toe also.
3.For the vehicles with 4WS, make the adjustments with
the 4WS tie rod end disconnected from the trailing arm.
TSB Revision

L
i
SERVICE BRAKES - Specifications
SERVICE SPECIFICATIONS
3msFWDAWD
andard value
Brake pedal heightmm (in.)
177 - 182 (7.0 - 7.2)
177 - 182 (7.0 - 7.2)Brake pedal free playmm (in.)
3-8(.1 -.3)3-8(.1 -.3)Brake pedal to floorboard clearance
mm (in.)
80 (3.1) or more
80 (3.1) or more
Pad thicknessmm (in.)
10.0 (.39)10.0 (.39)Front disc thickness
mm (in.)
24.0
t.94)30.0 (1.18)
Rear disc thickness
mm (in.)
18.0 (71)
20.0 (.79)Proportioning valve pressure
MPa (psi)
Split point
3.75 - 4.25 (533 - 604)3.75 - 4.25 (533 - 604)
Output pressure [input pressure]
5.23 - 5.73 (744 - 815)f8.0 (I, 138)]5.23 - 5.73 (744- 815)18.0 (1,138)]Booster
push;; (To,,;?aster cylinder piston
clearance
7
+ 8 inch brake booster
0.55 - 0.75 (.022 - ,030)-8 + 9 inch brake booster
0.65
- 0.85 (.026 - ,033)0.65 - 0.85 (026 - ,033)Disc brake drag force (tangential force of
wheel mounting bolts)
N (Ibs.)70 (15.4) or less
70 (15.4) or less
[Disc brake dragging torque[Nm (ft.lbs.)]
[4 (3) or less][4 (3) or less]
Speed sensor’s (ABS) internal resistance
kQFront
1.4-2.2
0.8 - 1.2
Rear1.3-2.1
0.8- 1.2
Rear speed sensor pole piece-to-rotor
tooth surface clearancemm (in.)
-28.15-28.45(1.11 -1.12)
Clearance between the
spmefm;l[yle piece
and the toothed rotor
Front0.3 - 0.9 (.012 - ,035)-
Rear0.2 - 0.7 (008 - .028)-nit
Left/right proportioning valve output
pressure difference
MPa (psi)0.4 (57)
0.4 (57)Front disc run-outmm (in.)
0.1
(.004) or less
0.1 (.004) or less
Pad thicknessmm (in.)
2.0
(08)2.0 (08)Front disc thicknessmm (in.)
22.4
(.88)28.4 (1.12)Front hub end playmm (in.)
0.05
(.002)0.05 (.002)Rear disc thicknessmm (in.)
16.4
(65)18.4 (.72)Rear disc run-outmm (in.)
0.08
(0031) or less
0.08 (.0031) or less
Rear hub end playmm (in.)
0.05
(002)0.8 (.031)
TSB Revision