1991 MITSUBISHI 3000GT lock

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-19
DABS warning light blinks once after the ignition key is turned to the “ON” position. It
(L.-Jilluminates in the “START” position and blinks once again when turned to the “ON” position.
[Explanation]
When power flows, the ABS ECU turns on theharness between the ECU and the warning light, the
warning light for approximately 1 sec. while itlight illuminates only when the valve relay is off in
performs a valve relay test. If there is a break in thethe valve relay test, etc.
IGNITIONSWITCH(IG1)
I
COMBINATION
METER
58
g:"I 2
3
mi
456788 7
ASS-ECUIn the ignition key “ON”
position, does voltage
between terminal No. 25 andground indicate battery
voltage?ABS warning light andECUis broken.
Yes
Repair harness.
vMalfunction of ABS ECU
+ Replace ABS ECU.
TSB Revision

35-20SERVICE BRAKES -Anti-lock Braking System Troubleshooting
the following diagnosis codes are displayed “11 FR SNSR. OPEN”
“12 FL SNSR. OPEN” “13 RR SNSR. OPEN” “14 RL SNSR. OPEN”
[Explanation]
The ABS ECU detects breaks in the wheel speed
sensor wire. This trouble code is output if the wheel
speed sensor signal is not input (or short circuited)
or if its output is low when starting to drive or while
driving.[Hint]
In addition to a broken wire/short circuit in the wheel
speed sensor, also check whether the sensor gap is
too large, sensor harness wire is broken, or sensor
harness and body connector are not properly
con-
netted.
r--~- -E-2 When dlagnosls code“15 VEH. SPD. SNSR.” is displayedI[Explanation]
This trouble code is output when there is an
abnormality (other than broken wire or short circuit)
in any of the wheel speed sensor output signals
while driving.
[Hint]
The following can be considered as the cause of the
wheel speed sensor output abnormality.
l Distortion of rotor, teeth missing
lLow frequency noise interference when sensor
harness wire is broken
l Noise interference in sensor signal
lSensor output signal is below the standard value
or amplitude modulation is over the standard
value. Using an oscilloscope to measure the
wave shape of the wheel speed sensor output
signal is very effective.l Broken sensor harness
l Poor connection of connector
NOTE(1) If contact is poor, check the sensor cable by
bending and lightly stretching it.
(2) Except for the case where a fault condition
exists in the system, but the inspection results
are normal; if an abnormality cannot be found in
the sensor circuit displayed as abnormal, erase
the diagnosis code and turn the ignition switch
to OFF once, and then test-drive again.
If the same trouble code is output, replace the
ABS ECU. If the trouble does not occur
any-more, the problem is likely to be with the ABS
ECU.(If the trouble is in the speed sensor circuit, but
is difficult to recreate, it will recur even after the
ABS ECU has been replaced.)
SPEED SENSOR
FRONTCLH) FRONTFTRH)RF.AR(LH) REfIR(RH)
@cTJ @ij@ fi&
1 TSB Revision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-21
Check flow connected with wheelNOTEspeed sensorWhen checking with an oscilloscope, first measure voltage
iivariations in the wheel speed sensor output. (Refer to P.35-57.)
No
Is the resistance value of the wheel
speed sensor part normal?
Standard value:Front 1.4 - 2.2 kRRear 1.3 - 2.1 kSZ
> Malfunction of wheel speed
sensor
Yes
Yes
1
IIs the standard value for
the gap between the wheel
speed sensor and rotor
within the range?
Standard value:;+;;fi3 - 0.9 mm LO12 -
poe288r,$ - 0.7 mm LOO8 -
Yes
I Yes
ICheck the output of each
wheel speed sensor with an
oscilloscope, including the
waveform. (Refer to mea-
surement of wheel speed
sensor output voltage
variations on
P.35-57.)Is the output voltage for
each wheel speed sensor
over the standard value and
is the waveform normal?
:
No-
Lsensor has a poor wave-
form. Replace sensor or
Yes
RB RevisionI

35-22SERVICE BRAKES -Anti-lock Braking System Troubleshootin,g
E-3When diagnosis code “22 STOP LAMP SW” is displayed
[Explanation]
The ABS ECU outputs this trouble code in the
following cases.
lStop light switch may remain on for more than
15 minutes without ABS operation.
lThe harness wire for the stop light switch may
be open.[Hint]
!LiIf the stop light operates normal, the harness for the
stop light switch input circuit is broken or there is a
malfunction in the ABS ECU.
r7
ABS-ECU-~
RESISTOR
Ll121314/5161716~9~10111~12~13~14/15(16i~7~1~~'9~20~1~2~2~24~~6~~~~9~30~3~~~~2~~5~
KK35-AK-R3506A
I
Yes6
Repair harness.
Malfunction of ABS ECUReplace ABS ECU.
‘visionI

SERVICE BRAKES -Anti-lock Braking System Troubleshooting35-23
E-4When diagnosis codes “41 FR SOL. VALVE”, “42 FL SOL. VALVE” or
“43 REAR SOL.
V.” are displayed.
iL[Explanation]
The ABS ECU normally monitors the solenoid valve
when turned OFF, the ECU determines the solenoid
drive circuit.
coil wire is broken/short-circuited or the harness is
If no current flows in the solenoid even if the ECU
broken/short-circuited, and then these trouble
turns the solenoid ON or if it continues to flow even
codes are output.
/
ii
LJ
$$l.E#AT'ON;;QO'D
4I
I
i
Ii'-. - - ---i>? 5 3 6
ABS-ECU-A22 Al9 *17 ,IY Y Y Y I
disconnect ECU connector
Yes
The harness wire for the
solenoid valve circuit
whose resistance value is
outside the range of the
standard value is brokenor short circuited.
I
Repair ABS harness.
Malfunction of ABS ECU
1) Replace ABS ECU.
TSB Revision

35-24SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-5When diagnosis code “51 VALVE RELAY” is displayed
[Explanation]
When the ignition switch is turned ON, the ABS
ECU switches the valve relay OFF and ON for an
initial check, compares the voltage of the signal to
the valve relay and valve power monitor line voltage
to check whether the valve relay operation isnormal. In addition, normally it monitors whether or
not there is power in the valve power monitor line
since the valve relay is normally ON. Then, if the
supply of power to the valve power monitor line is
interrupted, this trouble code will be output.
EPfiiB EenIGNITIONSWITCH(IG1)
COMSINATIONm
I
H” g@J$s2
4:u
,,8I. -----I/IL’ /
IIII
I /IIII/I/-,----__--_,>yo “-a-‘+G ------------------ ?$”:
;’m[1?610 2pEl%zq~,___ ____________~_______~~~~
>;?
$-:dL1:27 =Yi62.G 22 +%!
i.-I
1/2131a)5161718(QIIO(I ~~~2(13~~a~i5~~6/i7~~~IQ$O~Y~2~3~24~~6~~~28~~~1~2~3~4~5~Remove and check the valve relay.
IWhen the valve relay is checked, are
the following conditions found?
No. 85
-No. 86: Resistance
value 60 - 120 fiNo. 30-No. 87a: Continuity
No. 30 - No. 87: No continuity
When battery voltage is applied
between terminals No. 86 and No. 85.
No. 30
- No. 87: Continuity
No. 30 - No. 87a: No continuity
Yes
Install the valve relay and remove
the HU connector.
E+GG-pqReplace valve relay.
&I/ NnIIWith the ignition key “ON”, does the
Is there continuity between HU No. 8
and No. 7 terminals?
IYes
Connect the HU harness and remove
the ECU connector.Faulty harness in HU
1Does resistance between body con-
nector terminal No. 2 and terminal
No. 27 indicate 60
- 120 II
NoMalfunction of harness
between HU and ECU.
Yes
With the ignition key “ON”, does the
voltage between terminal No. 22 and
ground indicate battery voltage?
YesNo
II- Malfunction of harness
between HU and ABS
ECU.Repair harness.
vision

SERVICE BRAKES -Anti-lock Braking System Troubleshooting
I - IE 6 When diagnosis code “52 MOTOR RELAY” is displayed
[Explanation]
l When the motor continues to revolve
The ABS ECU outputs this trouble code for the
motor relay and motor in the following cases.
l When the motor relay does not function
lWhen there is trouble with the motor itself and it
does not revolve .[Hint]
If there is motor operation noise during MUT forced
drive mode, there is a broken or short circuited
motor monitor wire.
lWhen the motor ground line is disconnected and
the motor does not revolve
I Yes I
FUSIBLE LINKa
-_ ------- --10‘5 “1
n.-
7;:? 9rn’E5 u
p?GEilq”~+103 3-_------- --
ES-ECU2526.-
4
-;“I
1112I3/415151713Ig~10~1~~12~19114~15]1~17118j~ls~o~l~e~3~4’415~2T~E~~o~l~~~~~5~(X35-AK-33533Does the motor make a noise
during MUT forced drive modeBroken wire or short cir-
Remove the motor relay and
check resistance values.
No. 85
- No. 86: Resistance
value 30 - 60 fiNo. 30-No. 87: No continuity
Battery voltage is applied
between terminals No. 85 and
No. 86.Replace motor relay.
No. 30-No. 87: Continuity
Yes
Is pump motor ground connected
normally?Connect ground wire.
Yes
Install motor relay and remove
HU connector.
III NoI1Connect the HU connector
and remove the ECU connector
III NoI3Is resistance between body
connector terminal No. 5 and
ground 0.1 -0.3 R?Repair harness.
Yes
ABS ECU malfunction
P Replace ABS ECU.
1 TSB Revision

35-26SERVICE BRAKES -Anti-lock Braking System TroubleshootingI
TROUBLESHOOTING (ABS - AWD)Confirm condition in the following way and diagnosis accordingly.
Does the ABS warning light illuminate as described
below up to the time the engine starts?(2) With the ignition key in the “START” position,
(1) When the ignition key is turned to the “ON”power to the ABS ECU is interrupted and the
position, the ABS ECU causes the ABS warningABS warning light remains lit because the valve
relay is OFF.
light to flash four times in about one second (3) When the ignition key is returned from the
(during which the valve relay self check is made)
and then causes it to go out.“START” position to the “ON” position, the
ABS warning light flashes four times in about
one second (during which the valve relay self
-check is made again) and then goes out.
III
OFFu--I-II
ST
ONACC, LOCK
114A0594Yes
>CONTINUED ON NEXT PAGE
No
No.
Trouble condition
Major causesRemedy
1ABS warning light does not light up at all.l ABS warning light bulb is burnt out.
ACC,LOb--
l Open in ABS warning light electricalCheck, using flowchart A (Refer to
ABScircuit (check for blown fuse)P.35-31.)warningOFFlight
lgmtlon
key
14AO590
2When the ignition key is turned to the
“ON” position, it remains lighted.l Fail safe is functioning due to ECU
self diagnosis.Check, using flowchart B (Refer toABS,“,F
J-l Short in ECU warning light drive circuitP.35-34.)warningl Malfunction of ECUlight
Ignition
key.;i,LOi h
3Does not illuminate when ignition key is
in “START” position.l Malfunction of valve relayl Break in harness between ABS warningCheck, using flowchart C (Refer to
light and HUP.35-36.)l Break in harness between HU andwarning
body ground
TSB Revision1