1991 MITSUBISHI 3000GT lock

SERVICE. BRAKES -Anti-lock Braking System Troubleshooting35-43
E-6When diagnosis code “51 VALVE RELAY” is displayed
I
L[Explanation]
When the ignition switch is turned ON, the ABS
normal. In addition, normally it monitors whether or
ECU switches the valve relay OFF and ON for annot there is power in the valve power monitor line
initial check, compares the voltage of the signal tosince the valve relay is normally ON. If the supply of
the valve relay and valve power monitor line voltagepower to the valve power monitor line is inter-
to check whether the valve relay operation is
rupted, this trouble code will be output.
b
L
IGNlTIONSWITCH(IG1)
-I--
iz
=pi7TEaq
dI
6
7
Ed
COMBINATION
METER
--;Gm1 I 11
I /I
--- --
710 4Ii+
mI%
~d10 2
--- -- -?
ii3Dz62 27
iE b
1112j31a15(6/71618/10(11112113/14/15j16/17(18118~20~21~2~3~4~5~~~2@~~~0~31~2~3~~~35
KX35-AK-K3503
r-TSB I
( ;;reove;d ch; the>
4.IWhen the valve relay is checked,
are the following conditions
found?
No. 85
- No. 86: Resrstance
value 60 - 120 IINo. 30-No. 87a: Continuity
No. 30 - No. 87: No continuity
When batterv voltaoe IS aooliedbetween terminalsho. 86 and
No. 85.
No. 30
- No. 87: Contrnurty
No. 30 - No. 87a: No continurtyNo
I1-----+Valve relay malfunction
+l
IReplace valve relay.I
Yes
&I/ No1IWith the ignition key “ON”,
does the voltage between the
connector terminal No. 52 and
ground indicate battery voltage?
Yes
Connect the HU harness and
\ remove the ECU connector.
+II NnrIground Indicate battery voltage.
Replace ABS
ECIJ.
vision

35-44SERVICE BRAKES -Anti-lock Braking System Troubleshooting
E-7When diagnosis code “52 MOTOR RELAY” is displayed
[Explanation]
The ABS ECU outputs this trouble code for the
motor relay and motor in the following cases.
l When the motor relay does not function
lWhen there is trouble with the motor itself and it
does not revolve
lWhen the motor ground is disconnected and the
motor does not revolve
l When the motor continues to revolve
[Hint]
If there is motor operation noise during MUT forced
drive mode, there is a broken or short circuited
motor monitor wire.
FUSIBLE LINKa
=
::
s* m’ IL% Q7
plGizq”+-103 1
----..-___I _-
3%ECU2526L--h h
Th v-sTIII
14 ’
+---I
i”
’-ll21314 15 16 17 16 ~8~10)11~12~13~14~15~16~17~16~li1Q~0~1~~23~4~*6~2?~E~Q~30~1~2~33~~~5J
X35-AK-R3500during MUT forced drive mode?
Remove the motor relay.
I
1 ;;pa4r&&rness between 1
5Remove the motor relay and
check resistance values.
No. 85
- No. 86: Resistance
value 30 - 60 fiNo. 30 - No. 87: No continuity
Battery voltage is applied
kotw8esfn terminals No. 85 and
No. 30
- No. 87: ContinuityReplace motor relay.
1Yes
L
+I, NoIIIs pump motor ground connected
normally?Connect ground wire.
I
YesInstall motor relay and remove
HU connector.
@Vyiground indicate battery voltage?
I Yes
IConnect the HU connector
and remove the ECU connectorRepair harness.
J- No
Is resistance between bodyP Malfunction of harness
connector terminal No. 2
Lrbetween HU and ECU
and No. 26 30 - 60 a?
ItNc-11 I<
r 1 Repair harness.;~~:;$$a$?%dABS ECU malfunction
> Replace ABS ECU.
TSB Revision

SERVICE BRAKES - Set-vice Adiustment Procedures35-45lUF51F
Pedal
7\ \!4FOO7.
F14511
F14519
TSB Revision-_.1
SERVICE ADJUSTMENT PROCEDURES
BRAKE PEDAL INSPECTION AND ADJUSTMENT
1.Measure the brake pedal height as illustrated. If the’brakepedal height is not within the standard value, adjust as
follows.
Standard value (A): 177
- 182 mm (7.0 - 7.2 in.)
(I) Disconnect the stop light switch connector, loosen the
lock nut, and move the stop light switch to a position
where it does not contact the brake pedal arm.
(2) Adjust the brake pedal height by turning the operating
rod with pliers (with the operating. rod lock nut
loosened), until the correct brake pedal height is
obtained.
(3) After screwing in the stop light switch until it contacts
the brake pedal stopper (just before the brake pedal is
caused to move), return the stop light switch
l/2 to 1
turn and secure by tightening the lock nut.
(4) Connect the connector of the stop light switch.
(5) Check to be sure that the stop light is not illuminated
with the brake pedal unpressed.
Reference value (6): 0.5
- 1.0 mm (.02 - .04 in.)
2. On vehicles with automatic transaxle, check the shift-lock
mechanism. (Refer to GROUP 23
- Transaxle Control.)
3. With the engine stopped, depress the brake pedal two or
three times. After eliminating the vacuum in the power
brake booster, press the pedal down by hand, and confirm
that the amount of movement before resistance is met (the
free play) is within the standard value range.
Standard value (C): 3
- 8 mm (.I - .3 in.)
If the free play is less than the standard value, confirm that
the clearance between the stop light switch and brake
pedal is within the standard value.
If the free play exceeds the standard value, it is probably
due to excessive play between the clevis pin and brake
pedal arm. Check for excessive clearance and replace faulty
parts as required.
4.Start the engine, depress the brake pedal with approximate-
ly 500 N (110
Ibs.) of force, and measure the clearance
between the brake pedal and the floorboard.
Standard value (D): 80 mm (3.1 in.) or more
If the clearance is less than the standard value, check for air
trapped in the brake line and for brake fluid leaks. If
necessary, check the brake system mechanism (excessive
shoe clearance due to faulty auto adjuster) and repair faulty
parts as required.~1~1
I
I
I
I
I

SERVICE BRAKES - Service Adiustment Procedures
i14LO29C
1Al 0781
14LO291141029
1. Visually check the brake pad thickness through the inspec-
tion hole in the caliper body.
Standard value: IO.0 mm
(.39 in.)
Limit: 2.0 mm (.08 in.)
Caution
Replace the pad if worn beyond the limit. At this time,
replace the pads on right and left wheels as a set.
2. Remove the guide pin, raise the caliper assembly, and
support it with a wire, etc.
Caution
The guide pin has been coated with special
Igrease. Do
not wipe off the special grease on the lock pin, and do
not contaminate the lock pin.
3. Remove the following parts from the caliper support.@ Pad and wear indicator assembly
8 F$$ assembly
3 I@ Outer shim
4. Measure the rotating torque of the hub with the pads
removed to determine brake drag torque after pads are
installed.
5. Install the pad clips to the caliper support in position.
\14AO400
TSB Revision

35-50SERVICE BRAKES - Service Adjustment Procedures
Pad pin
1 AFnn97
6.Clean the piston and, using the special tool, push the piston
into the cylinder.
7.With care not to allow the piston boot to be wedged, lower
the caliper assembly and fit the lock pin.
8. Using the following procedure, check the brake drag
‘d ,
torque.@ Start the engine and depress and hold the brake pedal
for five seconds.@ Stop the engine. (Approx. 200 N
[44 Ibs.])@ Rotate the brake disc ten turns in the forward direction.@ Using a spring balance, check the brake drag force.
9. If the difference between the brake drag force and hub
rotating force exceeds the standard value, disassemble the
piston and check the piston sliding surfaces for dirt and
rust, piston seal for deterioration, and lock pin and guide pin
for sliding motion.
Standard value: 70 N (15.4 Ibs.)
[4 Nm (3 ftlbs.)] or less
1. Visually check the brake pad’ thickness. Through the
opening in the caliper body.
Standard value: 10.0 mm
(-39 in.)
Limit: 2.0 mm
(.08 in.)
Caution
‘L&iReplace the pad if worn beyond the limit. At this time,
replace the pads on right and left wheels as a set.
I2. Remove the clip and, holding the cross spring with hand,
remove the pad pins.
TSB Revision

35-52SERVICE BRAKES - Service Adjustment Procedures
14FOO94
k.!! I14FOO427. Using the following procedure, check the brake drag
torque.@ Start the engine and depress and hold the brake pedal
’for five seconds. [Approx. 200 N (44
Ibs.)]@ Stop the engine.@ Rotate the brake disc ten turns in the forward direction.@ Using a spring balance, check the brake drag force.
8. If the difference between the brake drag force and hub
rotating force exceeds the standard value, disassemble the
piston and check the piston sliding surfaces for dirt and
rust, piston seal for deterioration, and lock pin and guide pin
for sliding motion.
Standard value: 70 N (15.4
Ibs.) [4 Nm (3 ft.lbs.)] or less
INSPECTION OF FRONT BRAKE DISC THICKNESS1. Remove dirt and rust off the surface of the brake disc.
2.Measure the thickness of disc at four or more places of the
pad contacting surface.
Standard value:
24.0 mm (.94 in.)
30.0 mm (1.18 in.)
,Limit:
22.4 mm (.88 in.)
28.4 mm (1.12 in.)
3.If the wear exceeds the limit even at one place, replace the
right and left discs and brake pads as a set.
FRONT BRAKE DISC RUN-OUT CHECKM35FSAF
1. Remove the front brake assembly; and support it with a
wire, etc.
TSB Revision2. Place a dial gauge approximately 5 mm
(.2 in.) from the
outer circumference of the brake disc, and measure the
run-out of the disc.
Limit: 0.10 mm (.004 in.) or less
NOTESecure the disc to the hub with wheel nuts.

L.
SERVICE BRAKES -Service Adjustment Procedures35-53
I14A0398
14F003r
i14A04014NOO27
7
FRONT BRAKE DISC RUN-OUT CORRECTION
M35FFAC
1.If the run-out of the brake’disc is equivalent to or exceeds
the limit specification, change the phase of the disc and
hub, and then measure the run-out again.
(1) Before removing the brake disc, chalk both sides of the
wheel stud on the side at which run-out is greatest.
(2) Remove the brake disc, and then place a dial gauge as
shown in the illustration; then move the hub in the axial
direction and measure the play.
Limit: 0.05 mm (.002 in.)
If the play is equivalent to or exceeds the limit, replace
the front hub unit bearing.
(3) If the play does not exceed the limit specification, and
then check the run-out of the brake disc once again.
Mount the brake disc on the position dislocated from
the chalk mark.
2.If the run-out cannot be corrected by changing the phase of
the brake disc, replace the disc.
REAR DISC BRAKE PAD CHECK AND REPLACE-
MENTM35FUAE
1.Check brake pad thickness through caliper body check port.
Standard value: 10.0 mm
(39 in.)
Limit: 2.0 mm
(08 in.)
Caution
1.When the limit is exceeded, replace the pads at both
sides, and also the brake pads for the wheels on the
opposite side at the same time.
2.If there is a significant difference in the thicknesses
of the pads on the left and right sides, check the
sliding condition of the piston, lock pin sleeve and
guide pin sleeve.
2. Loosen the parking brake cable (from the vehicle interior),
and disconnect the parking brake end installed on the rear
brake assembly.
3. Remove lock pin. Lift caliper assembly and retain with
wires.
Caution
Do not smear special grease on lock pin or make it
dirty.
TSB Revision

SERVICE BRAKES - Service Adjustment Procedures
4. Remove the following parts from caliper support.@ Outer shim@ Pad assembly@ Pad & wear indicator assembly@ Clip@ Inner shim A@ Inner shim B
d
14N0031
f\
/0014N013714A040;14N003:
14AO401
l%FLision
14N01365. Measure hub torque with pad removed to measure brake
drag torque after pad installation.
On vehicles with VCU-equipped LSD, disengage the drive
shaft and companion flange.
NOTESecure the disc to the hub with wheel nuts.
6. Securely attach the pad clip to the caliper support.
Caution
Do not deposit
&ease or other dirt on pad or brake disc
friction surfaces.
7.Clean the piston and then push the piston into the cylinder.
8.With care not to allow the piston boot to be wedged, lower
the caliper assembly and fit the lock pin.
9. Check brake drag torque as follows.
(I) Start engine and hold brake pedal down for 5 seconds.
[Approx. 200 N (44
Ibs.)](2) Stop engine.
(3) Turn brake disc forward
10 times.
(4) Check brake drag torque with spring scale.
If the difference between brake drag torque and hub torque
exceeds the standard value, disassemble piston and clean
piston. Check for corrosion or worn piston seal, andcheck
the sliding condition of the lock pin sleeve and guide
pinl/jsleeve.
Standard value: 70 N (15.4
Ibs,,) [4 Nm (3 ft.lbs.)] or less