Diag. Code 22Airbag Warning Light System Malfunction
CIRCUIT DESCRIPTION
The airbag warning light is located on the combination meter.
When the airbag system is normal, the airbag warning light lights up for\
approx. 6 seconds after the
ignition switch is turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the airbag system, the airbag warning light\
lights up to inform the driver of
the abnormality.
When terminals Tc and E of the TDCL are connected, the diagnostic code is displayed by t\
he blinking
of the airbag warning light.
The airbag warning light circuit is equipped with an electrical connecti\
on check mechanism which
detects when the connector to the center airbag sensor assembly is not p\
roperly connected.
If the connector to the center airbag sensor assembly is not properly co\
nnected, the airbag warning
light will not light up.
Diagnostic code 22 is recorded when a malfunction occurs in the airbag w\
arning light system.
If an OPEN malfunction occurs in the airbag warning light system, the ai\
rbag warning light does not
light up, so that until the malfunction is repaired, the diagnostic code\
s (including code 22) cannot be
confirmed.
Code No.Diagnosis
22 Open circuit in airbag warning light system.22 Center airbag sensor assembly malfunction.
AB±74±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName
YES
Does airbag warning light turn off?
NO
1
Replace center airbag sensor assembly. Check airbag warning light circuit
or terminal AB circuit of TDCL or
check connector.
WIRING DIAGRAM
Airbag Warning Light System (Always Lit Up)
CIRCUIT DESCRIPTION
The airbag warning light is located on the combination meter.
When the airbag system is normal, the airbag warning light lights up for\
approx. 6 seconds after the
ignition switch is turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the airbag system, the airbag warning light\
lights up to inform the driver of
the abnormality.
When terminals Tc and E of the TDCL are connected, the diagnostic code is displayed by t\
he blinking
of the airbag warning light.
DIAGNOSTIC CHART
AB±84±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName
Customer Problem Analysis Check Sheet
SRS AIRBAG System Check Sheet
Registration No.
Customer 's NameRegistration Year/ /
Frame No.
Date Vehicle
Brought In/ /Odometer ReadingKm
Miles
Date of Problem Occurrence / /
WeatherFine Cloudy Rainy Snowy Various/Other
Conditions
Outdoor
TemperatureHot Warm Cool Cold (Approx. C ( F))
Conditions
at Time
of Problem
OccurrenceVehicle
Operation
Starting Idling
Driving
Constant speed Acceleration Deceleration Other]
[
Condition
of road
Details of Problem
Vehicle Inspection,
Repair History Prior
to Occurrence of
Malfunction
(Including Airbag
System)
(Diagnosis System Inspection)
Airba
g Warning1st Time Remain On Sometimes Lights Up Does Not Light UpAirbag Warning
Light Inspection2nd TimeRemain On Sometimes Lights Up Does Not Light Up
Diagnostic Code1st TimeNormal Code Malfunction Code [Code. ]Diagnostic Code
Inspection2nd TimeNormal Code Malfunction Code [Code. ]
AB±29SRS AIRBAG ± Troubleshooting
Inspector 's
Name:
WhereEverybodyKnowsYourName
Diagnosis Inspection
AIRBAG WARNING LIGHT CHECK
(a) Turn the ignition switch to ACC or ON and check that theairbag warning light lights up.
(b) Check that the airbag warning light goes out after approx. 6 seconds.
HINT:
wWhen the ignition switch is at ACC or ON and the airbag
warning light remains on, the center airbag sensor
assembly has detected a malfunction code.
wIf, after approx. 6 seconds have elapsed, the airbag
warning light sometimes lights up or the airbag warning
light lights up even when the ignition switch is OFF, a
short in the airbag warning light circuit can be
considered likely. Proceed to Airbag warning light
system (always lit up) on page AB±84.
DIAGNOSTIC CODE CHECK
1. OUTPUT DIAGNOSTIC CODE
(a) Turn the ignition switch to ACC or ON position and waitapprox. 20 seconds.
(b) Using SST, connect terminals Tc and E
1 of the TDCL.
SST 09843±18020
NOTICE: Never make a mistake with the terminal connec-
tion position as this will cause a malfunction.
2. READ DIAGNOSTIC CODE Read the diagnostic code as indicated by the number of
times the airbag warning light blinks.
wNormal code indication
The light will blink 2 times per second.
wMalfunction code indication
In the event of a malfunction, the light will blink. The first
number of the code No. will equal the first digit of a
2±digit diagnostic code, and after a 1.5 second pause,
the 2nd number of the code No. will equal the 2nd digit.
If there are two or more codes, there will be a 2.5 second
pause between each.
After all the codes have been output, there will be a 4.0 se-
cond pause and they will all be repeated.
HINT:
wIn the event of a number of trouble codes, indication will
begin from the smaller numbered code to the larger.
wIf a diagnostic code is not output or is continuously
output, proceed to the TC terminal circuit inspection on
page AB±86 .
AB±30
SRS AIRBAG
± Troubleshooting
WhereEverybodyKnowsYourName
Diagnostic Code Matrix Chart
If a malfunction code is displayed during the diagnostic code check, check\
the circuit listed for that code in the
table below (Proceed to the page given for that circuit).
Code No.DiagnosisPage
(Normal)*1Source voltage dropAB±40
11Short in squib circuit or front airbag sensor circuit (to ground)AB±42
12Short in squib circuit or front airbag sensor circuit (to +B)AB±48
13Short in squib circuit (between D+ wire harness and D± wire harness)\
AB±54
14Open in squib circuitAB±62
15Open in front airbag sensor circuitAB±68
22*2Airbag warning light system malfunctionAB±74
31Center airbag sensor assembly malfunctionAB±80
41*3Malfunction stored in memoryAB±82
HINT:
*1 When the airbag warning light remains lit up and the diagnostic code is the normal code, this means asource voltage drop.
*2 Code 22 is recorded when a malfunction occurs in the airbag warning light sy\
stem. If an open malfunction occurs in the airbag warning light system, the airbag warning light does not light up, so that until the mal-
function is repaired, the diagnostic code (including code 22) cannot be confir\
med.
*3 When a malfunction occurs in the airbag system, malfunction codes 11 to 31 are output. After repairing the malfunction indicated by malfunction codes 11 to 31, codes 11 to 31 are cleared from the memory, but
code 41 is output instead. Once the malfunction has been detected, the airba\
g warning light will remain
lit up until code 41 is cleared, even though the malfunction has been re\
paired.
Problem Symptom Chart
Proceed with troubleshooting of each circuit in the table below.
Problem SymptomInspection ItemPage
With the ignition switch at ACC or ON, the airbag warning light
sometimes lights up after approx. 6 seconds have elapsed.
Airbag warning light lights up even when ignition switch is in the
LOCK position.Airbag warning light system
(Always lit up)AB±84
Diagnostic code not displayed.
Diagnostic code continuously displayed.Tc terminal circuitAB±86
AB±34SRS AIRBAG ± Troubleshooting
WhereEverybodyKnowsYourName
DIAGNOSIS SYSTEM
AT09R±07
The electronically controlled transmission system has built±
in self±diagnostic functions. If the malfunction occurs in the
system, the ECM stores the malfunction code in memory and
the O/D OFF (Overdrive OFF) indicator light blinks to inform
the driver. The diagnostic trouble code stored in memory can
be read out by the following procedure.
O/D OFF INDICATOR LIGHT INSPECTION
AT09S±07
1. Turn the ignition switch to ON.
2. Check if the O/D OFF indicator light lights up when the O/D main switch is pushed out to OFF and goes off when
the O/D main switch is pushed in to ON.
HINT:
wIf the O/D OFF indicator light does not light up or stay on
all the time, carry out the check for ªO/D OFF Indicator
Light Circuitº on page AT±112.
w If the O/D OFF indicator light blinks, a trouble code is
stored in the ECM memory.
DIAGNOSTIC TROUBLE CODE CHECK
AT0A3±07
1. Turn the ignition switch ON, but do not start the engine.
2. Push in the O/D main switch to ON.
HINT: Warning and diagnostic trouble codes can be r ead only
when the O/D main switch is ON. If it is OFF, the O/D OFF indi-
cator lights up continuously and will not blink.
3. Using SST, connect terminals TE1 and E1 of the DLC2 or
DLC1.
SST 09843±18020
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±37
WhereEverybodyKnowsYourName
2. INSPECT BRAKE WARNING LIGHT(a) Disconnect the connector from the brake fluid warningswitch.
(b) Release the parking brake pedal.
(c) Connect terminals on the wire harness side of the level warning switch connector.
(d) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or wire har-
ness.
(Parking Brake Switch)
REMOVAL AND INSTALLATION OF PARKING
BRAKE SWITCH
1. REMOVE PARKING BRAKE SWITCH
(a) Remove the driver's seat.
(See page BO±58)
(b) Disconnect the connector and remove switch.
2. INSTALL PARKING BRAKE SWITCH For installation follow the removal procedure in reverse.
INSPECTION OF PARKING BRAKE SWITCH
1. INSPECT PARKING BRAKE SWITCH
(a) Check that there is continuity between terminal andswitch body with the switch ON (switch pin released).
(b) Check that there is no continuity between terminal and switch body with the switch OFF (switch pin pushed in.)
If continuity is not as specified, replace the switch or inspect
ground point.
2. INSPECT BRAKE WARNING LIGHT (a) Disconnect the connector from the parking brake switchand brake fluid warning switch.
(b) Ground terminal on the wire harness side connector.
(c) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or inspect
wire harness.
BE±116
±
BODY ELECTRICAL SYSTEM Combination Meter
WhereEverybodyKnowsYourName
( Coolant Level Warning Switch)
REMOVAL AND INSTALLATION OF COOLANT
LEVEL WARNING SWITCH
1. REMOVE COOLANT LEVEL WARNING SWITCH(a) Disconnect the connector.
(b) Remove the boot.
(c) Using the notches in the head of switch, turn the switchcounterclockwise and remove it.
NOTICE: Do not remove when engine is hot.
2. INSTALL COOLANT LEVEL WARNING SWITCH For installation, follow the removal procedure in reverse.
INSPECTION OF COOLANT LEVEL WARNING
SWITCH
1. INSPECT COOLANT LEVEL WARNING SWITCH(Continuity)
(a) Remove the radiator cap and open the radiator drainclock.
NOTICE: Do not remove when engine is hot.
(b) Drain the coolant about 1 liter. (1.1 US qts, 0.9 lmp. qts)
(c) Check that there is continuity between terminals (float down).
(d) Close radiator drain cock and fill the cooling system with
coolant.
(e) Check that there is no continuity between terminals (float up).
If continuity is not as specified, replace the switch.
2. INSPECT COOLANT LEVEL WARNING LIGHT (a) Disconnect the connector from the coolant level warning
switch and ground terminal 1 on the wire harness side
connector.
(b) Start the engine, check that the warning light lights up.
If the warning light does not light up, inspect the bulb or wire
harness.
±
BODY ELECTRICAL SYSTEM Combination MeterBE±117
WhereEverybodyKnowsYourName