1991 LEXUS SC400 engine

OKNG
OKNG
OKNG
INSPECTION PROCEDURE
1Main throttle position signal check.
C
OK
Hint
PTurn ignition switch ON (Do not start the engine).
Check voltage at the terminal T
T of the DLC2 while grad-
ually depressing the accelerator pedal from the fully
closed position to the fully opened position.
Voltage changes from 0 V to 8 V by stages.
Do not depress the brake pedal during this test. The
voltage will stay at 0 V if depressed.
Proceed to next circuit inspection shown on matrix chart
(See page AT±66).
2Check throttle position sensor.
See engine troubleshooting section in EG section.
Replace throttle position sensor.
3Check harness and connector between ECM and throttle position sensor (S\
ee page IN±33).
Repair or replace harness or connector.
Check and replace ECM.
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±103
WhereEverybodyKnowsYourName

OKNG
OKNG
OKNG
INSPECTION PROCEDURE
1Check voltage between terminal KD of ECM connector and body ground.
C
OK
P1. Connect the check harness A to the ECM (See EGsection).
2. Turn ignition switch ON (Do not start the engine.)
Measure voltage between terminal KD of ECM connec-
tor and body ground when accel. pedal is fully de-
pressed or not.
Proceed to next circuit inspection shown on matrix chart
(See page AT±66).
2Check kick±down switch.
C
OK
1. Disconnect dick±down switch connector. (See page AT±18)
2. Measure resistance between terminals 1 and 2 of kick±down switch connector when kick±down
switch is ON and OFF
Replace kick±down switch.
3Check harness and connector between ECM and kick±down switch, kick±down\
switch and
body ground (See page IN±33).
Repair or replace harness or connector.
Check and replace ECM
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±105
WhereEverybodyKnowsYourName

AT±66BE
IN±33
WIRING DIAGRAM
Stop Light Switch Circuit
CIRCUIT DESCRIPTION
The purpose of this circuit is to prevent the engine from stalling, while d\
riving in lockup condition, when
brakes are suddenly applied.When the brake pedal is operated, this switch sends a signal to ECM. Then
the ECM cancels operation of the lockup clutch while braking is in progress\
.
DIAGNOSTIC CHARTDIAGNOSTIC CHART
AT±108±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTING
WhereEverybodyKnowsYourName

OKNG
OKNG
OKNG
INSPECTION PROCEDURE
1Check operation of stop light.
Check if the stop lights go on and off normally when the brake pedal is operated and released.C
Check and repair stop light circuit (See BE section).
2Check stop light signal.
C
OK
1. Connect voltmeter to the terminals TT and E1 of the
DLC2.
2. Turn ignition switch ON (Do not start the engine).
3. Fully depress the accelerator pedal until the volt- meter indicates 8 V and hold it.
4. Depress and release the brake pedal and check the
voltage.
Proceed to next circuit inspection shown on matrix chart
(See page AT±66).
3Check harness and connector between ECM and stop light switch (See page\
IN±33).
Repair or replace harness or connector.
Check and replace ECM.
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION TROUBLESHOOTINGAT±109
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
AT0GH±02 Line pressure (wheel locked)\
 \

 \
 \
382±441 kPa 3.9±4.5 kgf/cm255±64 psi
 Engine idling D position\
 \

 \
 \
637±716 kPa 6.5±7.3 kgf/cm292±104 psi
 R position\
 \

\
1,265±1,402 kPa 12.9±14.3 kgf/cm2183±203 psi AT stall (Throttle valve opened) D position\
 \

 \
 \
1,726±2,060 kPa 17.6±21.0 kgf/cm2250±298 psi R position\
 \

 ECM SLN termina lNot ground\
 \
177±255 kpa 1.8±2.6 kgf/cm226±37 psi
 Ground\
 \
0
 Engine stall revolution\
 \
2,200+150 RPM
 Time lag N position " D position\
 \
Less than 1.2 seconds
 N position " R position\
 \
Less than 1.5 seconds
 Engine idle speed (Cooling fan and A/C OFF
)N position\
 \
650 RPM
 \
 \
Boot end face and inner cable stopper Throttle cable adjustment (Throttle valve fully closed)\
 \

 \
 \
0±1 mm 0±0.04 in.
 Torque converter clutch installing (Correct distance)\
 \
17.1mm 0.673 in.
 Drive plate runout Limit\
 \
0.20 mm 0.0079 in.
SHIFT POINT (Kick±down foot switch activated)
 Shift position Shifting point Vehicle speed km/h (mph)2
  Throttle valve fully opened 1"2 67±71 (42±44)
  2" 3 118±124 (73±77)
  3" O/D (NORM) 170±177 (106±110)
  3" O/D (PWR) 179±186 (111±116)
 D position (NORM or PWR) O/D "3 164±170 (102±106)
  3" 2 105±111 (65±69)  2" 1 53±57 (33±35) 

2 iti
 

Throttle valve fully opened 1
"2
 

67±71 (42±44)
 2 position
(NORM or PWR) 3
" 2 106±112 (66±70)
 
(NORM or PWR)
 2" 1 53±57 (33±35)
 L position Throttle valve fully opened 3 "2 104±109 (65±68)
 
L osition
(NORM or PWR) 2" 1 57±63 (35±39)
±
A340E (1UZ±FE) AUTOMATIC TRANSMISSION SERVICE SPECIFICATIONSAT±121
WhereEverybodyKnowsYourName

TORQUE SPECIFICATION
AT07F±04\
 \
Part tightened NVm kgf Vcm ft Vlbf\
 
\

\
Engine x Transmission
 

64
 

650
 

47
\
 \
Rear mounting x Body 25 260 19
\
 \
Rear mounting x Extension housing 25 250 18
\
 \
Transmission housing x Transmission case 14 mm (0.55 in.) 34 345 25
\
 \
17 mm (0.67 in.) 57 580 42
\
 \
Extension housing x Transmission case 34 345 25
\
 \
Valve body x Transmission case 10 100 7
\
 \
Oil strainer 10 100 7
\
 \
Oil pan 7.4 75 65 in.
Vlbf\
 \
No.1 vehicle speed sensor 16 160 12\
 
\

\
No.2 vehicle speed sensor 

5.4 

55 

48 in.
Vlbf
\
 \
Solenoid wiring stopper plate 5.4 55 48 in. Vlbf
\
 \
O/D direct clutch speed sensor 5.4 55 48 in. Vlbf
\
 \
Transmission output flange 123 1,250 90
\
 \
Throttle cable x Transmission case 5.4 55 48 in. Vlbf
\
 \
Union 29 300 22
\
 \
Cooler pipe union nut 34 350 25
\
 \
Drive plate x Crankshaft 99 1,000 72
\
 \
Torque converter clutch x Drive plate 33 340 25\
 \
Park/Neutral position switch Bolt 13 130 9\
 \
Nut 6.9 70 61 in. Vlbf\
 
\

\
Control shaft lever
 

16
 

160
 

12
±
A340E (1UZ±FE) AUTOMATIC TRANSMISSION SERVICE SPECIFICATIONSAT±123
WhereEverybodyKnowsYourName

DESCRIPTION
GENERAL DESCRIPTION
AT0GE±02
The A340E automatic transmission is a 4±speed Electronically Controlled \
Transmission with an intelligent
control like the A341E automatic transmission used in the LS400. The A34\
0E automatic transmission has
the following features.

When shifting, engine torque is controlled and the clutch hydraulic pressure\
in the transmission is
electronically controlled to reduce transmission shift shock.

A new type of ATF (ATF Type T±II) is used which provides improved shifting characteristics a\
nd
prevents deterioration in the ATF over time.
HINT: For the A340E automatic transmission, use ATF Type T±II or equivalent.

A super flow torque converter clutch is used to improve the transmission\
efficiency.
The A340E automatic transmission is mainly composed of a torque converter c\
lutch with lock±up clutch,
4±speed planetary gear unit, hydraulic control system and the electro\
nic control system.
To minimize the possibility of incorrect operation of the automatic transm\
ission, a shift lock mechanism has
also been added.
AT±2
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION DESCRIPTION
WhereEverybodyKnowsYourName

 
Type of Transmission  A340E
\
 \
Type of Engine61UZ±FE
\
 
\

\
Torque Converter Clutch Stall Torque Ratio1.900 :1
\
 \
Torque Converter Clutch Lock±up MechanismEquipped
 Gear Ratio 1st Gear 2.804
  2nd Gear 1.531 


 

3rd Gear
 

1.000
  O/D Gear 0.705
  Reverse Gear 2.393
 
Number of Discs/Plates 
O/D Direct Clutch (C0) 
2 / 2 


 

Forward Clutch (C1)
 

6 / 6
  Direct Clutch (C2) 4 / 4
  2nd Brake (B0) 5 / 5 


 

1st & Reverse Brake (B2)
 

7 / 7
  O/D Brake (B0) 5 / 4
 2nd Coast Brake (B) Band Width mm (in.) 40 (1.57)
 ATF TypeATF Type T±II or equivalent 

Capacity liter (US qts, lmp. qts)
 

Total
 

8.2 (8.7, 7.2)
  Drain & Refill 1.9 (2.0, 1.7)
±
A304E (1UZ±FE) AUTOMATIC TRANSMISSION DESCRIPTIONAT±3
WhereEverybodyKnowsYourName