1991 LEXUS SC400 wheel

5. Non±reusable parts(a) Always replace cotter pins, gaskets, O±rings and oilseals etc. with new ones.
(b) Non±reusable parts are indicated in the component
illustrations by the º º symbol.
6. Precoated parts Precoated parts are bolts and nuts, etc. that are coated with
a seal lock adhesive at the factory.
(a) If a precoated part is retightened, loosened or causedto move in any way, it must be recoated with the
specified adhesive.
(b) Recoating of precoated parts
(1) Clean off the old adhesive from the bolt, nut or threads.
(2) Dry with compressed air.
(3) Apply the specified seal lock adhesive to the bolt or nut threads.
(c) P re co a te d pa rts are in d ica te d in th e co m ponent
illustrations by the º
º symbol.
7. When necessary, use a sealer on gaskets to prevent leaks.
8. Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
9. Use of special service tools (SST) and special service materials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where specified
and follow the proper work procedure. A list of SST and SSM
can be found in the preparation part at the front of each
section in this manual.
10. When replacing fuses, be sure the new fuse has the correct
amperage rating. DO NOT exceed the rating or use one with
a lower rating.
11. Care must be taken when jacking up and supporting the vehicle. Be sure to lift and support the vehicle at the proper
locations (See page IN±33).
(a) If the vehicle is to be jacked up only at the front or rear end, be sure to block the wheels at the opposite end in
order to ensure safety.
(b) After the vehicle is jacked up, be sure to support it on
stands. It is extremely dangerous to do any work on a
vehicle raised on a jack alone, even for a small job that
can be finished quickly.
±
INTRODUCTION General Repair InstructionsIN±5
WhereEverybodyKnowsYourName

12. Observe the following precautions to avoid damage to theparts:
(a) Do not open the cover or case of the ECU unless
absolutely necessary (If the IC terminals are touched, the
IC may be destroyed by static electricity.).
(b) To pull apart electrical connectors, pull on the connectoritself, not the wires (See page BE±2).
(c) Be careful not to drop electrical components, such as sensors or relays. It they are dropped on a hard floor,
they should be replaced and not reused.
(d) When checking continuity at the wire connector, insert the tester probe carefully to prevent terminals from
bending.
(e) To disconnect vacuum hoses, pull on the end, not the middle of the hose.
(f) When steam cleaning an engine, protect the distributor,
coil and air filter from water.
(g) Ne ve r use an imp a ct wre n ch to re mo ve or in sta ll temperature switches or temperature sensors.
(h) When using a vacuum gauge, never force the hose onto
a connector that is too large. Use a step±down adapter
instead. Once the hose has been stretched, it may leak.
13. Tag hoses before disconnecting them: (a) When disconnecting vacuum hoses, use tags to identify
how they should be reconnected.
(b) After completing a job, double check that the vacuum hoses are properly connected. A label under the hood
shows the proper layout.
14. Installation of wheels The wheel assemblies are of the uni±directional type and
must be rotated only between the front and rear as illustrated.
Wheels are marked with turning direction indicators.
When installing the wheels, check the marks carefully and
install the wheel correctly.
15. Bleeding of traction control system When repairing the brake master cylinder or TRAC system,
bleed the air out of the TRAC system (See page BR±7).
CAUTION: Since the fluid is under high pressure, it could
spray out with great force, so be careful.
IN±6
±
INTRODUCTION General Repair Instructions
WhereEverybodyKnowsYourName

When the negative (±) terminal cable is disconnected from
the battery, memory of the clock and audio systems will be
cancelled. So before starting work, make a record of the con-
tents memorized by each memory system. Then when work
is finished, reset the clock and audio systems as before.
When the vehicle has power tilt and power telescopic steer-
ing, power seat, power outside rear view mirror and power
shoulder belt anchorage, which are all equipped with
memory function, it is not possible to make a record of the
memory contents. So when the operation is finished, it will be
necessary to explain this fact to the customer, and ask the
customer to adjust the features and reset the memory.
To avoid erasing the memory of each memory system, never
use a back±up power supply from outside the vehicle.
3. Even in cases of a minor collision where the airbag does not deploy, the front airbag sensors and the steering wheel pad
should be inspected. (See page AB±9)
4. Never use airbag parts from another vehicle. When replacing parts, replace them with new parts.
5. Before repairs, remove the airbag sensors if shocks are likely
to be applied to the sensors during repairs.
6. The center airbag sensor assembly contains mercury. After
performing replacement, do not destroy the old part. When
scrapping the vehicle or replacing the center airbag sensor
assembly itself, remove the center airbag sensor assembly
and dispose of it as toxic waste.
7. Never disassemble and repair the front airbag sensors, center airbag sensor assembly or steering wheel pad in order
to reuse it.
8. If the front airbag sensors, center airbag sensor assembly or steering wheel pad have been dropped, or if there are cracks,
dents or other defects in the case, bracket or connector,
replace them with new ones.
9. Do not expose the front airbag sensors, center airbag sensor assembly or steering wheel pad directly to hot air or flames.
10. U s e a v o l t / o h m m e t e r w i t h h i g h i m pedance (10 kW/V
minimum) for troubleshooting of the electrical circuit.
11. Information labels are attached to the periphery of the airbag components. Follow the notices.
12. After work on the airbag system is completed, perform the
airbag warning light check (See page AB±30).
±
INTRODUCTION Precautions for Vehicles Equipped with SRS AirbagIN±9
WhereEverybodyKnowsYourName

FRONT AIRBAG SENSOR
1. Never reuse the front airbag sensors involved in a collisionwhen the airbag has deployed. (Replace both the left and
right airbag sensors.)
2. Install the front airbag sensor with the arrow on the sensor facing toward the front of the vehicle.
3. The front airbag sensor set bolts have been anti±rust treated. When the sensor is removed, always replace the set bolts
with new ones.
4. The front airbag sensor is equipped with an electrical connection check mechanism. Be sure to lock this
mechanism securely when connecting the connector. If the
connector is not securely locked, a malfunction code will be
detected by the diagnosis system (See page AB±10).
SPIRAL CABLE (IN COMBINATION
SWITCH)
The steering wheel must be fitted correctly to the steering column
with the spiral cable at the neutral position; otherwise cable dis-
connection and other troubles may result. Refer to page AB±15
of this manual concerning correct steering wheel installation.
STEERING WHEEL PAD (WITH AIRBAG)
1. When removing the steering wheel pad or handling a new steering wheel pad, it should be placed with the pad top
surface facing up.
In this case, the twin±lock type connector lock lever should
be in the locked state and care should be taken to place it so
the connector will not be damaged. And do not store a steer-
ing wheel pad on top of another one. (Storing the pad with its
metallic surface up may lead to a serious accident if the air-
bag inflates for some reason.)
2. Never measure the resistance of the airbag squib. (This
may cause the airbag to deploy, which is very
dangerous.)
IN±10±
INTRODUCTION Precautions for Vehicles Equipped with SRS Airbag
WhereEverybodyKnowsYourName

3. Grease should not be applied to the steering wheel pad andthe pad should not be cleaned with detergents of any kind.
4. Store the steering wheel pad where the ambient temperature remains below 93
C (200
F), without high humidity and
away from electrical noise.
5. When using electric welding, first disconnect the airbag connector (yellow color and 2 pins) under the steering
column near the combination switch connector before
starting work.
6. When disposing of a vehicle or the steering wheel pad alone, the airbag should be deployed using an SST
before disposal (See page AB±91). Perform the
operation in a place away from electrical noise.
CENTER AIRBAG SENSOR ASSEMBLY
The connector to the center airbag sensor assembly should be
connected or disconnected with the sensor mounted on the floor.
If the connector is connected or disconnected while the center air-
bag sensor assembly is not mounted to the floor, it could cause un-
desired ignition of the airbag system.
WIRE HARNESS AND CONNECTOR
The airbag system's wire harness is integrated with the cowl wire
harness assembly. The wires for the airbag wire harness are en-
cased in a yellow corrugated tube. All the connectors for the sys-
tem are also a standard yellow color. If the airbag system wire har-
ness becomes disconnected or the connector becomes broken
due to an accident, etc., repair or replace it as shown on page
AB±22 .
±
INTRODUCTION Precautions for Vehicles Equipped with SRS AirbagIN±11
WhereEverybodyKnowsYourName

PRECAUTIONS FOR VEHICLES
EQUIPPED WITH TRACTION
CONTROL (TRAC) SYSTEM
When using a rear wheel two±wheel drum tester such as a
speedometer tester or chassis dynamometer, etc., or jacking up
the rear wheels and driving the wheels, always push in the TRAC
cut (ºTRAC OFFº) switch and turn the TRAC system OFF.
CONFIRM TRAC SYSTEM IS OFF
1. Press the TRAC cut (ºTRAC OFFº) switch.
2. Check that the TRAC OFF indicator light comes on when the
TRAC system is turned off by the TRAC cut switch.
HINT: The TRAC indicator light should always operate right after
the engine is restarted.
3. Begin measurements.
4. Press the TRAC cut switch again to change the TRAC to operative and check that the TRAC OFF indicator light goes
off.
HINT: The TRAC indicator light blinks when the TRAC system is
operative.
±
INTRODUCTION Precautions for V
ehicles Equipped with Traction Cotnrol
(TRAC)SystemIN±13
WhereEverybodyKnowsYourName

 
Diag. Code 14\
 \
Open in Squib Circuit
DIAGNOSTIC CHARTDIAGNOSTIC CHART
The squib circuit consists of the center airbag sensor assembly, spiral cable and the steering wheel pad
(squib). It causes the airbag to deploy when the airbag deployment con\
ditions are satisfied.
For details of the function of each component, see FUNCTION OF COMPONENT\
S on page AB±5.
Diagnostic code 14 is recorded when an open is detected in the squib cir\
cuit.
 Code No.\
 \
Diagnosis
 



14
\
 
\


\

\


Open circuit in D+ wire harness or D wire harness of squib.
 Squib malfunction.
 Spiral cable malfunction.
 Center airbag sensor assembly malfunction.
AB±62±
SRS AIRBAG Troubleshooting
WhereEverybodyKnowsYourName

Preperation.
Check squib circuit.
Check spiral cable.Check harness between center airbag
sensor assembly and spiral cable.
Check center airbag sensor assembly.
Check squib.
From the results of the above inspection, the
malfunctioning part can now be considered
normal. To make sure of this, use the simula-
tion method to check. Go to step
Repair or replace spiral cable.
Repair or replace harness or con-
nector between center airbag sen-
sor assembly and spiral cable. Replace center airbag
sensor assembly
Replace steering wheel pad.
WIRING DIAGRAM
DIAGNOSTIC CHARTDIAGNOSTIC CHART
±
SRS AIRBAG TroubleshootingAB±63
WhereEverybodyKnowsYourName