1991 LEXUS SC400 light

11 5
CURRENT ALWAYS FLOWS TO TERMINAL (A)8 OF THE DOOR LOCK ECU THROUGH THE DOOR FUSE, AND TO TERMINAL (A)20
THROUGH THE DOME FUSE.
WHEN THE IGNITION SW IS TURNED ON, THE CURRENT FLOWING THROUGH THE ECU±IG FUSE " TERMINAL (A)2 OF THE ECU "
TERMINAL (B)8 FLOWS THROUGH THE COIL SIDE OF THE POWER MAIN RELAY TO GROUND, CAUSING THE RELAY TO OPERATE.
THE CURRENT FLOWING THROUGH THE POWER FUSE FLOWS TO THE DOOR LOCK CONTROL SW LH, CAUSING THE INDICATOR
LIGHT TO LIGHT UP.
1. MANUAL LOCK OPERATION
WHEN THE DOOR CONTROL SW OR KEY SW ARE PUSHED TO LOCK POSITION, A LOCK SIGNAL IS INPUT TO TERMINAL (A)17, (A)14
(FOR KEY SW) OF THE DOOR LOCK ECU AND CAUSES THE ECU TO FUNCTION. CURRENT FLOWS FROM TERMINAL (A)8 OF THE
ECU " TERMINAL (A)4 " TERMINAL 5 OF THE DOOR LOCK MOTORS " TERMINAL 2 " TERMINAL (A)3 OF THE ECU " TERMINAL
(A)16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO LOCK.
2. MANUAL UNLOCK OPERATION
WHEN THE DOOR LOCK CONTROL SW OR KEY ARE PUSHED TO UNLOCK POSITION, AN UNLOCK SIGNAL IS INPUT TO TERMINAL
(A)18, (A)10 (FOR KEY SW LH) OR (A)15 (FOR KEY SW RH) OF THE DOOR LOCK ECU AND CAUSES THE ECU TO FUNCTION.
CURRENT FLOWS FROM TERMINAL (A)8 OF THE ECU " TERMINAL (A)3 " TERMINAL 2 OF THE DOOR LOCK MOTORS " TERMINAL
5 " TERMINAL (A)4 OF THE ECU "TERMINAL (A)16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO
UNLOCK.
WHEN UNLOCK OPERATION OCCURS USING THE LH DOOR KEY SW, PERFORMING THE UNLOCK OPERATION ONCE UNLOCKS
ONLY THE DRIVER'S DOOR. TO UNLOCK ALL THE OTHER DOORS TOGETHER, UNLOCK OPERATION MUST BE PERFORMED AGAIN
WITHIN 3 SECONDS OF THE FIRST OPERATION.
3. IGNITION KEY REMINDER OPERATION
* OPERATION OF DOOR LOCK BUTTON (OPERATION OF DOOR LOCK MOTORS)
WHEN THE IGNITION KEY IS IN THE CYLINDER (UNLOCK WARNING SW ON) AND THE DOOR IS OPENED AND LOCKED USING
DOOR LOCK BUTTON (DOOR LOCK MOTOR), THE DOOR IS LOCKED ONCE BUT EACH DOOR IS UNLOCKED SOON BY THE
OPERATION OF THE ECU. AS A RESULT OF ECU ACTIVATION, THE CURRENT FLOWS FROM TERMINAL (A)8 OF THE ECU "
TERMINAL (A)3 " TERMINAL 2 OF THE DOOR LOCK MOTORS " TERMINAL 5 " TERMINAL (A)4 OF THE ECU " TERMINAL (A)16
" TO GROUND AND CAUSES ALL THE DOORS TO UNLOCK.
THE SAME APPLIES TO OPERATION OF THE DOOR LOCK CONTROL SW AND DOOR LOCK KEY SW.
* KEY LESS LOCK OPERATION
WHEN THE IGNITION KEY IS STILL INSERTED IN THE CYLINDER (UNLOCK WARNING SW ON), THE DOOR IS OPEN AND UNLOCK
OPERATION IS PREVENTED BY KEEPING THE DOOR LOCK BUTTON PRESSED TO THE LOCK SIDE, THE DOOR IS KEPT IN THE
LOCK CONDITION. IF THE DOOR IS THEN CLOSED, A SIGNAL IS INPUT TO THE ECU FROM THE DOOR COURTESY SW. THIS
ACTIVATES THE ECU AND EACH DOOR IS UNLOCKED.
SYSTEM OUTLINE
WhereEverybodyKnowsYourName

11 6
THEFT DETERRENT AND DOOR LOCK CONTROL
D 7, D 8 DOOR KEY LOCK AND UNLOCK SW LH, RH
1±2 : CLOSED WITH DOOR LOCK CYLINDER UNLOCKED WITH KEY
3±2 : CLOSED WITH DOOR LOCK CYLINDER LOCKED WITH KEY
D10, D11 DOOR LOCK MOTOR, DOOR UNLOCK DETECTION SW AND DOOR OPEN DETECTION SW LH, RH
1±4: CLOSED WITH UNLOCK POSITION
E 5 ENGINE HOOD COURTESY SW
1±2: CLOSED WITH ENGINE HOOD OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
9±10: CLOSED WITH IGNITION KEY IN CYLINDER
L 5 LUGGAGE COMPARTMENT KEY UNLOCK SW
1±3: CLOSED WITH DOOR LOCK CYLINDER UNLOCK WITH KEY
L 6 LUGGAGE COMPARTMENT LIGHT SW
1±GROUND: CLOSED WITH DOOR OPEN
T 8(B) THEFT DETERRENT AND DOOR LOCK ECU
1±GROUND: CONTINUITY WITH LUGGAGE COMPARTMENT DOOR TO UNLOCK POSITION
12±GROUND: CONTINUITY WITH ENGINE HOOD OPEN
10±GROUND: CONTINUITY WITH LUGGAGE COMPARTMENT DOOR OPEN
7±GROUND: APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
T 9(A) THEFT DETERRENT AND DOOR LOCK ECU
1±GROUND: APPROX. 12 VOLTS WITH SHIFT LEVER IN N OR P POSITION AND IGNITION SW AT ST POSITION
2±GROUND: APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
6±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
7±GROUND: CONTINUITY WITH FRONT RH DOOR TO UNLOCK POSITION
8±GROUND: ALWAYS APPROX. 12 VOLTS
10±GROUND: CONTINUITY WITH DOOR LOCK KEY SW LH TO UNLOCK POSITION
11±GROUND: CONTINUITY WITH FRONT LH DOOR TO UNLOCK POSITION
12±GROUND: CONTINUITY WITH FRONT RH DOOR OPENED
13±GROUND: CONTINUITY WITH FRONT LH DOOR OPENED
14±GROUND: CONTINUITY WITH DOOR LOCK KEY SW RH TO LOCK POSITION
15±GROUND: CONTINUITY WITH DOOR LOCK KEY SW RH TO UNLOCK POSITION
20±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1428F 926N 127
C2328F1028P 531
D 730F1430T 127
D 830I1529T 8B29
D 930L 129T 9A29
D1030L 430T1529
D1130L 530
E 526L 630
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
422LEFT KICK PANEL (J/B NO.1 LEFT)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE1J20COWL WIRE
1K
3A22INSTRUMENT PANEL WIRE3F22INSTRUMENT PANEL WIRE
SERVICE HINTS
WhereEverybodyKnowsYourName

10
TROUBLESHOOTING
VOLTAGE CHECK
(a) Establish conditions in which voltage is present at thecheck point.
Example: ± Ignition SW on
± Ignition SW and SW 1 on
± Ignition SW, SW 1 and Relay on (SW 2 off)
(b) Using a voltmeter, connect the negative lead to a good ground point or negative battery terminal, and the
positive lead to the connector or component terminal.
This check can be done with a test light instead of a
voltmeter.
CONTINUITY AND RESISTANCE CHECK
(a) Disconnect the battery terminal or wire so there is novoltage between the check points.
(b) Contact the two leads of an ohmmeter to each of the check points.
If the circuit has diodes, reverse the two leads and check
again.
When contacting the negative lead to the diode positive side
and the positive lead to the negative side, there should be
continuity.
When contacting the two leads in reverse, there should be no
continuity.
(c) Use the volt/ohmmeter with high impedance (10 k W/V
minimum) for troubleshooting of the electrical circuit.
WhereEverybodyKnowsYourName

11
FINDING A SHORT CIRCUIT
(a) Remove the blown fuse and disconnect all loads of thefuse.
(b) Connect a test bulb in place of the fuse.
(c) Establish conditions in which the test bulb comes on.
Example: ± Ignition SW on
± Ignition SW and SW 1 on
± Ignition SW, SW 1 and Relay on (Connect theRelay) and SW 2 off (or Disconnect SW 2)
(d) Disconnect and reconnect the connectors while watching the test bulb.
The short lies between the connector where the test
bulb stays lit and the connector where the bulb goes
out.
(e) Find the exact location of the short by lightly shaking the problem wire along the body.
CAUTION:
(a) Do not open the cover or the case of the ECU unlessabsolutely necessary. (If the IC terminals are touched,
the IC may be destroyed by static electricity.)
(b) When replacing the internal mechanism (ECU part) of the digital meter, be careful that no part of your body or
clothing comes in contact with the terminals of leads
from the IC, etc. of the replacement part (spare part).
DISCONNECTION OF MALE AND FEMALE
CONNECTORS
To pull apart the connectors, pull on the connector itself, not the
wire harness.
HINT: Check to see what kind of connector you are disconnecting
before pulling apart.
WhereEverybodyKnowsYourName

104
TURN SIGNAL AND HAZARD WARNING LIGHT
1E
7 2
1A
71A 41C 41C 31E19 1E14
2 3 2 3 1H
11 1H 7
1J 1 3G
3
3A 1
1E 18
1K 6 3D
10
4
4
4
4
4
IQ2
8
IQ1
10 IQ1
12 IQ1 11
IG2
9IG1 10 IG123
IQ2
13
I7 I7
B15
EB EA BM IF 55
9
756 4123 10 8
66
1
4
2
5
3
A
16 A 17
B
23
IG2
8
IQ2 3
IE19
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
HAZARD TURNRH
LH
OFF
ON 20A
TURN
25A
HAZ±HORN
TURN SIGNAL
FLASHER TURN SIGNAL SW [COMB. SW]
HA ZARD SW
FRONT TURN
SIGNAL LIGHT
REAR TURN SIGNAL LIGHT
[REAR COMB. LIGHT] TURN SIGNAL INDICATOR
LIGHT [COMB. METER]
LH RH RH
LH WW
R±W R±B
R±W
R±W W±R
R±B
G± Y
G± B
W±BW±B
W±B
W±B
G±R
G±R
W
W
W±R
W±B
W±R
R±WR±B
R±B
R±W
R±W
R±B
R±W
W±BR±B
G±Y
G±B
G±Y
G±B
G±Y
G±Y G±B
W±B W±B
W±B W±B W±B W±B
W±B 5
R±B
H7
C16
F7 F8 R10 R11
C13 , C 1 4AB
LH RH
6
WhereEverybodyKnowsYourName

106
TURN SIGNAL AND HAZARD WARNING LIGHT
WhereEverybodyKnowsYourName

184
UNLOCK AND SEAT BELT WARNING
1E
12
3A
4
3D
13
1B
5 2
B
1
A
7
1E 1
1H
13
1D
10
1J
1 1C
12 1D 8
1I
15
9
10
6 3
2
1
BK
IF 10A
DOME
10A
GAUGE
SEAT BELT
WARNING LIGHT
[COMB. METER]
INTEGATION RELAY
BUZZER TI M ER
UNLOCK
WARNING SW
[IGNITION SW] BUCKLE
SW LH
DOOR OPEN
DETECTION
SW LH
FROM POWER SOURCE SYSTEM
(
SEE PAGE 56 )
FROM POWER SOURCE SYSTEM(
SEE PAGE 56 )
C12 ,C 14
D10
B4
I15
R
R
Y
Y
W±B
W±B
W±B
Y
W±B
W±B
W±B W±B B±L B±L
R±W
W±B
W±B
V
86
5
10 179
AB
1 2
(W/ MEMORY )
( W/O MEMORY )
( W/ MEMORY )
( W/O MEMORY )
Ba1
14
Ba2
5 Ba2
6 Ba1
11
WhereEverybodyKnowsYourName

185
CURRENT ALWAYS FLOWS TO TERMINAL 1 OF THE INTEGRATION RELAY THROUGH DOME FUSE.
1. SEAT BELT WARNING SYSTEM
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 7 OF THE INTEGRATION RELAY.
AT THE SAME TIME, CURRENT FLOWS TO TERMINAL 9 OF THE RELAY FROM THE GAUGE FUSE THROUGH THE SEAT BELT
WARNING LIGHT. THIS CURRENT ACTIVATES THE INTEGRATION RELAY AND, FOR APPROX. 4±8 SECONDS, CURRENT FLOWING
THROUGH THE WARNING LIGHT FLOWS FROM TERMINAL 9 OF THE RELAY " TERMINAL 10 " GROUND, CAUSING THE WARNING
LIGHT TO LIGHT UP. AT THE SAME TIME AS THE WARNING LIGHT LIGHTS UP, A BUCKLE SW OFF SIGNAL IS INPUT TO TERMINAL 8
OF THE RELAY, THE CURRENT FLOWING TO TERMINAL 7 OF THE RELAY FLOWS FROM TERMINAL 10 " GROUND AND THE SEAT
BELT WARNING BUZZER SOUNDS FOR APPROX. 4±8 SECONDS. HOWEVER, IF THE SEAT BELT IS PUT ON DURING THIS PERIOD
(WHILE THE BUZZER IS SOUNDING), SIGNAL INPUT TO TERMINAL 8 OF RELAY STOPS AND THE CURRENT FLOW FROM TERMINAL 7
OF THE RELAY " TERMINAL 10 " GROUND IS CUT, CAUSING THE BUZZER TO STOP.
2. UNLOCK WARNING SYSTEM
WITH THE IGNITION KEY INSERTED IN THE KEY CYLINDER (UNLOCK SW ON), THE IGNITION SW STILL OFF AND \
DOOR OPEN (DOOR
COURTESY SW ON), WHEN A SIGNAL IS INPUT TO TERMINAL 6 OF THE RELAY, THE INTEGRATION RELAY OPERATES, CURRENT
FLOWS FROM TERMINAL 7 OF THE RELAY " TERMINAL 10 " GROUND AND UNLOCK WARNING BUZZER SOUNDS.
B 4 BUCKLE SW LH
1±2 : CLOSED WITH DRIVER'S LAP BELT IN USE
D10 DOOR COURTESY SW LH
3±6 : CLOSED WITH LH DOOR OPEN
I15 UNLOCK WARNING SW [IGNITION SW]
10±9: CLOSED WITH IGNITION KEY IN CYLINDER
INTEGRATION RELAY
10±GROUND: ALWAYS CONTINUITY6±GROUND: CONTINUITY WITH DRIVER'S DOOR OPEN
5±GROUND: CONTINUITY WITH IGNITION KEY IN CYLINDER
8±GROUND: CONTINUITY WITH DRIVER'S LAP BELT IN USA
9±GROUND: 0 VOLTS FOR 4±8 SECONDS WITH IGNITION SW ON AND APPROX. 12 VOLTS 4±8 SECONDS AFTER IGNITION SW ON
1±GROUND: ALWAYS APPROX. 12 VOLTS
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 432C14B28I1529
C12A28D1030
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
219ENGINE COMPARTMENT LEFT
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B20ENGINE ROOM MAIN WIRE
1C20FLOOR MAIN
1D20FRONT DOOR LH WIRE
1E20INSTRUMENT PANEL WIRE
1H
1I20COWL WIRE
1J
20COWL WIRE
3A22INSTRUMENT PANEL WIRE3D22INSTRUMENT PANEL WIRE
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
Ba142FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)Ba242FLOOR WIRE AND FRONT SEAT LH WIRE (UNDER THE FRONT LH SEAT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IF36LEFT KICK PANEL
BK40UNDER THE CENTER PILLAR LH
SYSTEM OUTLINE
SERVICE HINTS
WhereEverybodyKnowsYourName