1990 HONDA PRELUDE engine

4. (2.0 Si,Si)

Remove the center cap from the wheel cover by turning the lock

to 90°.

(Si with 4WS or ALB)
Remove the center cap from the wheel by prying it out with a
common flat screwdriver (not provided in the tool bag).
(2.0 Si,Si)

CAUTION:
(On the Si model with 4WS or ALB)
Hold the center cap with your hand then pry it off using a rag to
protect the
cap and the wheel.

5. Use the lug wrench to loosen the wheel lug nuts
counterclockwise one-half turn.
Follow tire changing preparations and procedures carefully to
reduce the possibility of injury. The jack
is designed for changing
tires only.
STAND CLEAR, DO NOT get under the car and DO NOT
run the engine when the car Is supported only by the jack.
6. Place the jack under the jack point nearest the wheel you are removing; align the jack head so the car frame will fit in the recess
as you raise the jack.
To reduce the possibility of injury, be sure to use the jack provided with the car and the correct jacking points; never use any otherpart of the car for jack support.
RAG

(cont'd)

CENTER CAP


CENTER CAP
(Si with 4WS or ALB)
FLAT

SCREWDRIVERProCarManuals.comMain Menu t s

Jump Starting
To start a car with a dead battery, use another battery of the same voltage, and the proper jumper cables. Procedures other than those below could cause injury or
damage from battery acid spray, explosion or charging system

overload.

Never connect the jumper cable directly to the negative post of
the "dead" battery.
Never allow the two cars to touch each other.
Never allow the jumper cable clamps to touch each other.
Never lean over the battery when making connections.
Never attempt to jump start a vehicle with a frozen battery. The
battery could rupture and explode. If you suspect a frozen
battery, remove the vent caps and check the fluid. If there
seems to be no fluid, or if you see ice, do not attempt a jump
start until the fluid thaws.

CAUTION:

If jumper cables are connected backwards, the car's main fuse
may blow.
1.Turn off all lights, heater and other electrical loads, set parking
brake, and
shift transmission to Neutral or Park.
2. Use one cable to connect the positive terminal of the booster battery to the positive terminal of the "dead" battery.

(cont'd)

Do not attach cable here

DEAD BATTERY
Positive to positive
Negative to the engine, not to the battery

BOOSTER BATTERYProCarManuals.comMain Menu t s

Jump Starting (cont'd)
3. Use the other cable to connect the negative terminal of the booster battery to the engine at the ground cable as shown.
4.To remove the cables, reverse the above procedures exactly.
DO NOT push or tow a car to start it. The forward surge when the
engine starts could cause a collision. Also, under some conditions,
the catalytic converter could be damaged. A car equipped with an
automatic transmission cannot be started by pushing or towing.
NOTE:
After jump-starting the car, there is a possibility that the ALB
warning light may come on due to insufficient battery voltage. After
the battery is sufficiently recharged and the engine is turned off and restarted, the ALB warning light should indicate that the ALB
system is OK, by coming on for a few seconds each time the engine is started. If the light remains on after recharging, have it checked

by a Honda dealer.ProCarManuals.comMain Menu t s

If towing is necessary, contact a professional towing service. Your
authorized Honda dealer can assist you with detailed towing
instructions.
Never use tow chains or rope to tow a car; your ability to safety
control the car may be adversely affected.
We recommend the following:
Flat Bed Equipment — Entire car is winched on a flat bed vehicle.
This is the best way of transporting your Honda.
Wheel Lift Type — Tow with the front wheels off the ground.

If the
car can only be towed with the front wheels on the ground:

make sure the transmission is full of fluid (see page 86 — 87)

and tow with the transmission in neutral (N) and the ignition key in
the I position.

CAUTION:

To avoid serious damage on automatic transmission cars, first start the engine and shift to D, then to N and shut the engine off. If
the engine does not run or the transmission cannot be shifted
while the engine is running, the car must be transported on flatbed equipment.
Check local regulations for towing.

CAUTION:
Do not exceed 35 mph (55 km/h) or tow for distances of more
than 50 miles (80 km). If a Sling Type tow is used, the tow truck driver should position
wood spacer blocks between your car's frame and the chains
and lift straps to avoid damaging the bumper and the body. Do not use the bumpers to lift the car or to support the car's
weight while towing.
When towing a car with 4WS even with the front wheels off the ground, turn the wheels straight ahead and tie the steering wheel in place. TowingProCarManuals.comMain Menu s t

If Your Car Gets Stuck
If your car gets stuck in sand, mud, or snow, call a professional
towing service for assistance in getting your car out,

CAUTION:
Do not rev up the engine and allow the wheels to spin freely at
high speed. Severe transmission damage may result if the wheels are allowed to spin for more than a few seconds. DO NOT try to free a car with automatic transmission from
snow etc. by rocking the car alternately between forward and
reverse gears. Severe transmission damage may result from
shifting into gear with the wheels moving.ProCarManuals.comMain Menu s t

Headlight Motors
Proceed as follows if either headlight motor fails to operate:
1. Lift the hood and remove the cover from the engine compartment fuse box.

FUSE BOX

RIGHT
HEADLIGHT,
MOTOR
LEFT

HEADLIGHT
MOTOR
RIGHT HEADLIGHT LEFT HEADLIGHT
2. Use the label on the fuse box cover to locate the fuse for the headlight motor that doesn't work. Remove the fuse with the
fuse remover located in the fuse box under the dashboard.

FUSE

REMOVER FUSE

BOX

COVERProCarManuals.comMain Menu s t

Specifications

* 1 Including the coolant in the reserve tank (0.75 l /0.79US qt/0.66 Imp qt) but excluding that remaining in the engine.

* 2 Excluding the oil remaining in the engine,but including that remaining in the oil filter.

(cont'd)ProCarManuals.comMain Menu t s

Identification Numbers
The Vehicle identification Number (V.I.N.) is stamped on a plate attached to the top left side of the dashboard.It also appears on the Certification label attached to the door jamb,
as well as under the hood on the body, directly behind the air

cleaner.

NOTE:

The V.I.N. is also provided in bar code on the Certification label.
VEHICLE IDENTIFICATION NUMBER
TRANSMISSION NUMBER

ENGINE NUMBERThe Engine Number is stamped on the right front side of the engine

block.

The Transmission Number appears on a label on the top edge of the
transmission where
it attaches to the engine.CERTIFICATION LABEL
VEHICLE
IDENTIFICATION
NUMBERProCarManuals.comMain Menu t s