1988 JEEP CHEROKEE clutch

RADIATOR FAN BLADE INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B ........... Require replacement.
Attaching hardware
broken ................. A .. Require repair or replacement
of hardware.
Attaching hardware
missing ................ C ......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Bent .................... A ........... Require replacement.
Broken .................. A ........... Require replacement.
Cracked ................. A ........... Require replacement.
Loose ................... A . Require repair or replacement.
Missing ................. C ........... Require replacement.









\









\









\









\









\









\









\


RADIATOR FAN CLUTCHES
NOTE: Some lateral movement, measured at the fan blade tip,
may be normal.
RADIATOR FAN CLUTCH INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bearing noisy ........... A ............ Require replacement.
Bearing worn ............ A ............ Require replacement.
Fastener loose .......... A ... Require repair or replacement
of fastener.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. 1 ............ Suggest replacement.
Seized .................. A ............ Require replacement.
Slips (insufficient fan
speed) ................. A ............ Require replacement.
Thermal control
incorrect .............. B .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.









\









\









\









\









\









\









\


RADIATORS
RADIATOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Air flow restriction .... A ................. Require repair.

Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.









\









\









\









\









\









\









\


SENSORS AND ACTUATORS
NOTE: Conditions pertaining to the sensors and actuators listed
in this section may be found under the name of the sensor
or actuator.
SENSOR ABBREVIATION TABLE









\









\









\









\









\









\









\


Sensor Abbreviation
Accelerator Pedal Position Sensor ......................... APP
Air Conditioning Cycling Switch ............................ AC
Air Conditioning Pressure Sensor ........................... ..
Air Fuel Ratio Sensor ...................................... ..
Barometric Pressure Sensor ............................... BARO
Camshaft Position Sensor .................................. CMP
Clutch Pedal Position Switch .............................. CPP
Cooling Fan Motor Sensors and Switches ..................... ..
Crankshaft Position Sensor ................................ CKP
Electronic Transmission Feedback Devices ................... ..
Engine Coolant Temperature Sensor ......................... ECT
Evaporative Emission feedback devices ...................... ..
Exhaust Gas Recirculation feedback devices ................. ..
Fan Control Sensor ......................................... FC
Intake Air Temperature Sensor ............................. IAT
Knock Sensor ............................................... KS
Manifold Absolute Pressure Sensor ......................... MAP
Mass Air Flow Sensor ...................................... MAF
O2 Sensor ................................................. O2S
Park Neutral Position Switch .............................. PNP
Power Steering Pressure Sensor ............................ PSP
Thermal Vacuum Valve ...................................... TVV
Throttle Position Sensor ............................ TP Sensor
Throttle Position Switch ................................... ..
Transmission Range Switch ........................... TR Switch
Vehicle Speed Sensor ...................................... VSS
Volume Air Flow Sensor .................................... VAF









\









\









\









\









\









\









\


ACTUATOR ABBREVIATION TABLE








\









\









\









\









\









\









\


Actuator Abbreviation
Air Injection Control Solenoid ............................. ..
Electronic Transmission control devices .................... ..
Evaporative Emission Canister ............................ EVAP
Purge Device ............................................... ..
Exhaust Gas Recirculation Device .......................... EGR
Fuel Injector .............................................. ..
Idle Air Control .......................................... IAC

ECU is a digital microprocessor computer. Data sensors
provide the ECU with engine operating information in varying
electrical signals. ECU calculates this information and corrects
air/fuel ratio, ignition timing, and emission control as needed to
maintain efficient engine operation. Other ECU output signals control
upshift indicator light (manual transmission only), ignition module
dwell and A/C clutch operation.
UPSHIFT INDICATOR
On vehicles equipped with a manual transmission, ECU
controls upshift indicator light. Indicator light is normally
illuminated when ignition is turned on without engine running.
Indicator light is turned off when engine is started.
Indicator light will be illuminated during engine operation
in response to engine load and speed. If transmission is not shifted,
ECU will turn light off after 3 to 5 seconds. A switch located on
transmission prevents indicator light from being illuminated when
transmission is shifted to highest gear.
DATA SENSORS & SWITCHES
Manifold Absolute Pressure (MAP) Sensor
MAP sensor is located in engine compartment on firewall,
behind engine. MAP sensor monitors manifold vacuum via a vacuum line
from intake manifold to sensor.
MAP sensor supplies an electrical signal which keeps ECU
informed of manifold vacuum and barometric pressure conditions. This
information is combined with data supplied by other sensors to
determine correct air/fuel ratio.
Oxygen Sensor
Oxygen (O2) sensor is mounted in exhaust manifold where it
is exposed to exhaust gas flow. Its function is to monitor oxygen
content of exhaust gases and to supply ECU with a voltage signal
directly proportional to this content.
If oxygen content of exhaust gases is high (lean air/fuel
mixture), voltage signal to ECU is low. As oxygen content decreases
(mixture becomes richer), signal voltage increases.
In this way, ECU is kept constantly informed of air/fuel
ratio. ECU can then alter fuel injector "on" time, in response to
these signals, to obtain best air/fuel ratio of 14.7:1 under any
given operating conditions.
O2 sensor is equipped with a heating element that keeps
sensor at proper operating temperatures. Maintaining correct sensor
temperatures at all times guarantees a more accurate signal to ECU.
By using an O2 heater, fuel control system may also enter "closed
loop" operating mode sooner and maintain this mode, even during
periods of extended idle.
Temperature Sensors
There are 2 temperature sensors used on this system.
Manifold Air Temperature (MAT) sensor, mounted in intake manifold,
measures temperature of incoming air/fuel mixture and Coolant
Temperature Sensor (CTS), located on left side of cylinder block just
below the exhaust manifold, measures temperature of engine coolant.
Information provided by these 2 sensors to ECU allows ECU to
demand slightly richer air/fuel mixtures and higher idle speeds
during cold engine operation.
Throttle Position Sensor (TPS)
TPS is regulated by movement of throttle shaft. It is

include Park/Neutral switch (automatic transmission only), air
conditioning clutch, and Sync Pulse switch. When A/C or Park/Neutral
switches supply ECU with an "on" signal, module signals ISS motor to
change idle speed to a specific RPM.
With A/C on and throttle blade above a specific angle, ECU
de-energizes A/C relay, preventing A/C clutch from engaging until
throttle blade angle is reduced.
Sync pulse switch, located within distributor, generates a
signal to ECU, helping to properly synchronize sequential fuel
injection opening with intake valve opening.
ADJUSTMENTS
NOTE: Idle speed and air/fuel mixture are controlled by ECU and
are non-adjustable. On-car adjustment procedures for other
components should not be necessary during normal vehicle
operation or maintenance. Adjustments of components should
only be required when a faulty component is replaced with a
new one.
THROTTLE POSITION SENSOR (TPS)
1) Turn ignition on. Check throttle position sensor input
voltage. Connect voltmeter negative lead to terminal "B" (M/T), or
terminal "D" (A/T) of sensor connector. Connect voltmeter positive
lead to terminal "A" (M/T and A/T) of sensor connector.
NOTE: On (A/T) models, connector terminals are identified by
letters molded into back of connector. On all models, do not
disconnect TPS harness connector. Insert voltmeter test
leads through back of wire harness connector. On some
models, it may be necessary to remove throttle body from
intake manifold to gain access to sensor wire harness.
2) Move and close throttle plate completely (M/T and A/T).
Ensure throttle linkage contacts stop. Note voltmeter reading. Input
voltage at terminals "B" and "A" (M/T), or terminals "A" and "D"
(A/T) should be 5 volts.
3) Return throttle plate to closed throttle position (M/T
and A/T). Check sensor output voltage. To do so, disconnect voltmeter
positive lead from terminal "A" and connect it to terminal "C" (M/T),
or terminal "B" (A/T).
4) Maintain throttle plate in closed position (M/T and A/T).\
Ensure throttle linkage contacts stop. Note voltmeter reading. Output
voltage should be .8 volt (M/T), or 4.2 volts (A/T).
5) If output voltage is incorrect, loosen bottom sensor
retaining screw and pivot sensor in adjustment slot for a coarse
adjustment. Loosen top sensor retaining screw for fine adjustments.
Tighten screws after adjustment.
TESTING & TROUBLE SHOOTING
PRELIMINARY CHECKS & PRECAUTIONS
Subsystem Checks
The following systems and components must be in good
condition and operating properly before assuming a fuel injection
system malfunction.
* Air filter.
* All support systems and wiring.

\003
FU EL IN JE C TIO N S YSTE M - T B I

1 988 J e ep C hero ke e
1988 Electronic Fuel Injection
JEEP/RENIX THROTTLE BODY INJECTION
2.5L Cherokee, Comanche, Wagoneer, Wrangler
DESCRIPTION
The Throttle Body Injection (TBI) system is a single
injector system that introduces fuel into throttle body from above
throttle plate. Fuel injector, located within throttle body, is
controlled by the Electronic Control Unit (ECU).
The ECU is a sealed microprocessor that receives input
signals from several sensors and other related engine components.
Based on these inputs, ECU generates output signals that control and
adjust air/fuel mixture and ignition timing as necessary for proper
engine performance.
ECU also controls engine idle speed, emission control
systems, upshift indicator light (manual transmission only), and A/C
compressor clutch.
OPERATION
ELECTRONIC CONTROL UNIT (ECU)
On Cherokee, Comanche and Wagoneer, ECU is located under
instrument panel, above accelerator pedal. On Wrangler, ECU is
located behind glove box. Input information from various engine
sensors to ECU is used to determine engine operating conditions and
needs. Battery voltage input is used to ensure that correct output
voltage is supplied by ECU during fluctuations in battery voltage.
FUEL INJECTOR
Fuel injector is mounted in throttle body so that fuel is
injected into incoming airflow. When injector solenoid is energized,
armature and plunger move upward against spring. Check ball above
injector nozzle moves off seat and opens small orifice at end of
injector.
Fuel supplied to injector is forced around ball and through
orifice, resulting in fine spray of fuel. Volume of fuel injected is
dependent only on length of time that injector is energized by ECU,
as fuel pressure is constant at injector. During cold engine starts,
extra fuel is supplied so richer mixture will aid in starting.
FUEL PRESSURE REGULATOR
Fuel pressure regulator is integral part of throttle body.
Pressure regulator has a spring chamber that is vented to same
pressure as tip of injector. Because differential pressure between
injector nozzle and spring chamber is same, only the length of time
that injector is energized controls volume of fuel injected.
Fuel pump delivers more fuel than is required by engine.
Excess fuel goes to fuel tank from pressure regulator via fuel return
hose. Fuel pressure regulator function is mechanical and ECU does not
control it.
FUEL PUMP

ECU receives inputs from A/C when either A/C switch is in
"ON" position or compressor clutch engages to lower temperature. ECU
changes engine idle speed depending upon A/C compressor operation.
POWER STEERING PRESSURE SWITCH
ECU receives input from pressure switch during periods of
high pump load and low engine RPM. Input signals from pressure switch
to ECU are routed through A/C request and A/C select input circuits.
When pump pressure exceeds 250-300 psi (17.5-21.0 kg/cm
), switch
contacts close transmitting an input signal to ECU. ECU raises engine
idle speed immediately after receiving input from pressure switch.
RELAYS
Starter Motor Relay
Starter motor relay provides an input signal to ECU when
starter motor is engaged.
System Power Relay
System power relay, located on right fender inner panel, is
energized when engine is started. It remains energized for 3 to 5
seconds after ignition is off. This allows ECU to extend ISA for next
start before ECU shuts down.
Fuel Pump Control Relay
Fuel pump control relay is located on right fender inner
panel. Battery voltage is supplied to relay from ignition switch.
When ground is provided by ECU, relay becomes energized and provides
voltage to fuel pump.
A/C Compressor Clutch Relay
ECU controls A/C compressor clutch through this relay. The
A/C compressor clutch relay is located beside fuel pump control relay
on right fender inner panel.
EGR Valve/Canister Purge Solenoid
Vacuum to both EGR valve and vapor canister is controlled by
this solenoid. When solenoid is energized, neither EGR valve nor
vapor canister receive vacuum.
Solenoid is energized during closed (idle) and wide open
throttle operations, engine warm-up and rapid acceleration or
deceleration. If solenoid wire connector is disconnected, both EGR
valve and vapor canister will receive vacuum at all times.
Load Swap Relay
The load swap relay works in conjunction with power steering
switch to disengage A/C compressor clutch. If compressor clutch is
engaged when power steering pressure switch contacts close, input
signal from switch to ECU also activates load swap relay. Relay then
cuts off current to A/C compressor clutch.
The A/C compressor clutch remains disengaged until pressure
switch contacts reopen and engine idle returns to normal. The load
swap relay contains a timer that delays engaging the compressor
clutch for 0.5 second to ensure smooth engagement.
ADJUSTMENTS
CAUTION: When working on or near engine that is running, be very
careful to avoid pulleys, belts and fan. DO NOT stand in
direct line with blades of fan. DO NOT wear clothing that is
loose enough to get caught in moving parts.

2) To determine if front axle has completed a shift out of
4WD into 2WD, position mode select switch back to "4WD" position while
operating vehicle at slow speed. If vehicle shifts into 2WD, axle will
ratchet. If shift is not completed, transfer case will shift into 4WD
and hissing sound will come from mode select switch.
FRONT AXLE SHIFT MOTOR TEST
1) Disconnect vacuum harness from front axle shift motor.
Connect vacuum pump to shift motor front port. Apply 15 in. Hg vacuum
to shift motor. Rotate right front wheel to disengage axle.
2) Shift motor should hold vacuum at least 30 seconds. If
not, replace motor. If motor does hold vacuum, disconnect vacuum pump
from shift motor front port. Connect pump to shift motor rear port and
cap transfer case connecting port. Apply 15 in. Hg vacuum to motor.
3) Shift motor should hold vacuum for at least 30 seconds. If
not, replace motor. If motor does hold vacuum, remove cap from shift
motor transfer case connecting port and check for vacuum. If no vacuum
is present, rotate right front wheel to ensure axle has shifted
completely. Axle must completely shift to open shift motor connecting
port.
4) Recheck vacuum at shift motor transfer case port. If
vacuum is present, transfer case requires diagnosis. Command-Trac uses
Model 207 transfer case. Selec-Trac uses Model 228 transfer case.
REMOVAL & INSTALLATION
LOCKING HUB
Removal
1) Remove cover to outer clutch housing. Remove bearing race
spring assembly. Remove sealing ring and seal bridge retainer. Remove
bearing components.
2) Squeeze tangs of wire retaining ring together with needle-
nose pliers. Pull remaining components of automatic hub from wheel.
Installation
1) Ensure lock ring is in position. Using Bearing Nut Wrench
(J-6893-D), tighten wheel bearing adjusting nut to 50 ft. lbs. (60 N.\
m) to seat bearings.
2) Back off nut and tighten to 35 ft. lbs. (47 N.m) while
rotating hub. Finally, back off nut a maximum of 3/8 turn. Assemble
lock ring (with tab in keyway) over axle shaft, against bearing
adjustment nut.
3) Adjustment nut pin must pass through one of the washer
holes. Tighten outer adjusting nut to 183 ft. lbs. (248 N.m). Align
outer clutch housing splines with splines of wheel hub.
4) Loosen cover screws 3 or 4 turns, and push in on cover to
allow retaining ring to expand into rotor hub groove. Tighten cover
cap screws to 40-50 INCH lbs. (4.5-5.6 N.m).
Fig. 2: Selec-Trac Vacuum Control System
AXLE SHIFT MOTOR & HOUSING

Fig. 10: Identification Label Locations
Courtesy of American Motors Corp.
LUBRICATION SPECIFICATIONS
LUBRICATION SPECIFICATIONS TABLE








\









\









\









\









\









\









\



Application Fluid Specifications
Automatic Transmission ......................... Dexron-IIE ATF
Brake Master Cylinder ......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant .......... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil ( 1)
Gasoline Engine
Temperature Range
Above 30
\b F (-1\bC) ....... SAE 20W-40 Or 20W-50 API SH/CD
Above 0\b F (-18\bC) ........ SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60\b F (16\bC) .............. SAE 5W-30 API SH/CD
Diesel Engine
Temperature Range
Above 30
\b F (-1\bC) ................ SAE 15W-40, 20W-40 Or
20W-50 API SH/CD
0
\b F (-18\bC) to 100\b F (38\bC) ...... SAE 10W-30 API SH/CD
Less Than 50\b F (10\bC) .............. SAE 5W-30 API SH/CD
Front Axle ................................ SAE 80W-90 API GL-5
Rear Axle ................................. SAE 80W-90 API GL-5
Rear Axle (Trac-Lok) ( 2) ................. SAE 80W-140 API GL-5
Rear Axle (Trailer Towing) ( 3) .......... SAE 75W-140 Synthetic
Hydraulic Clutch .............. DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ....................... SAE 75W-90 API GL-5
Manual Steering Box .............. Multi-Purpose NLGI Grade 2EP
Power Steering Pump ...................... Power Steering Fluid
Transfer Case .................................. Dexron-IIE ATF