1988 JEEP CHEROKEE clutch

STE ER IN G C O LU M N

1988 J e ep C hero ke e
1988 STEERING
Jeep Steering Columns
All Models
DESCRIPTION
All models use collapsible steering columns. All columns have
integral ignition switch and locking device. Optional tilt wheel is
available with both A/T and M/T. Transmission shift linkage is
integral on all models except those with floor shift.
TROUBLE SHOOTING
Refer to TROUBLE SHOOTING - BASIC PROCEDURES article in the
GENERAL TROUBLE SHOOTING section.
REMOVAL & INSTALLATION
NOTE: Steering column removal and installation procedures refer to
all manufacturers. Not all procedures, however, apply to all
models.
STEERING COLUMN (COLUMN SHIFT)
Removal
1) Disconnect battery negative cable. Disconnect transmission
shift cable rod by prying rod from grommet in shift lever. Remove
cable clip. Remove cable from lower bracket.
2) Disconnect, as equipped, either the flexible coupling,
"Pot" coupling or "U" joint from pinion shaft.
3) Disconnect wiring connectors at column jacket. Remove
steering wheel and horn pad. See STEERING WHEEL & HORN REMOVAL
article. Remove damper assembly (if equipped). On RWD models, remove
turn signal lever.
4) On all models, remove steering column-to-floor pan
attaching screws. Expose steering column bracket. Remove instrument
panel steering column cover. Lower reinforcement. Disconnect bezel.
Remove indicator set screw and gearshift pointer from shift housing.
5) Remove steering column bracket-to-instrument panel
attaching nuts. Lower support bracket. Firmly grasp steering column
assembly and pull rearward while disconnecting lower stub shaft from
pinion shaft coupling.
NOTE: On vehicles equipped with cruise control and M/T, take care
not to damage clutch pedal cruise control switch.

Fig. 10: Manual Transmission & Clutch

intermediate clutch shaft snap ring from mainshaft.
5) Remove clutch shaft thrust ring. Remove intermediate
clutch shaft. Remove differential retaining snap ring. Remove
differential assembly. Remove differential needle bearings and thrust
washers from mainshaft. Remove low range fork and hub.
6) Remove shift sector. Remove shift sector bushing and "O"
ring. Remove front bearing retainer. Remove input gear snap ring.
Using a press, remove input and low range gear assembly from input
gear bearing. Remove low range gear snap ring.
7) Remove input gear retainer, thrust washers and input gear.
Mark differential halves for reassembly purposes. Separate
differential halves. Remove planetary gear and thrust washers.
8) Record mainshaft gear and sprocket gear position. Remove
gears. Remove front output shaft front bearing oil seal, snap ring and
front bearing. Using a press, remove input gear bearing.
9) Using slide hammer and internal puller, remove input gear
pilot bearing. Using slide hammer and internal puller, remove front
output shaft rear bearing.
Fig. 1: Exploded View Of Model 242 Transfer Case
Courtesy of Chrysler Motors.
CLEANING & INSPECTION

1) Clean all parts with solvent. Dry with compressed air.
Replace all oil seals, "O" rings and snap rings. Check all parts for
wear or damage. Replace all worn or damaged parts. Apply Dexron II to
all parts before installing.
2) Inspect low range annulus gear inside front case. If gear
is worn or damaged, replace case and gear as an assembly. Replace oil
pump as an assembly if any part is damaged or worn.
NOTE: When installing bearings, ensure bearing bores are aligned
with oil feed holes.
TRANSFER CASE REASSEMBLY
1) Install front output shaft front bearing, snap ring and
oil seal. Install snap ring on input gear bearing. Using a wooden
block and press, install input gear until snap ring is against case.
2) Install input gear pilot bearing. Assemble low range gear,
thrust washers, input gear and retainer. Install low range gear snap
ring. Ensure snap ring is seated properly in groove.
3) Start input gear shaft through the bearing in front case.
Using a press, install input gear shaft through bearing. Ensure
adapter is positioned properly before pressing shaft.
NOTE: Ensure proper size tool is used to press input gear shaft;
wrong size tool can damage case and thrust washers and will
move pilot bearing too far into gear bore.
4) Install input gear snap ring. Install front bearing
retainer oil seal. Apply 1/8" bead of silicone sealant to front
bearing retainer mating surface. Install front bearing retainer on
front case. Install sector shaft "O" ring and bushing. Install shift
sector.
5) Install detent pin, spring and plug. Install low range
fork pads. Assemble low range fork and hub. Ensure low range fork pin
is engaged in shift sector slot. Install differential sprocket gear in
lower differential case. Install planet gears and new thrust washers
on lower case pins.
6) Ensure thrust washers are positioned on top and bottom of
each planet gear. Install mainshaft gear. Align marks on upper and
lower differential case. Install bolts and tighten to specifications.
See TORQUE SPECIFICATIONS . Install needle bearing spacer on mainshaft.
7) Using petroleum jelly to hold needles, install bearings on
mainshaft. Install other spacer. Install differential assembly. Ensure
all needle bearings are in place. Install differential snap ring.
Install intermediate clutch shaft. Install thrust washer and snap
ring. Install mode shift sleeve in mode fork.
8) Install mode fork assembly on mainshaft. Ensure mode shift
sleeve splines engage with differential splines. Install mode fork and
mainshaft assembly in case. If necessary, rotate mainshaft slightly to
engage mainshaft with low range components.
9) Install mode fork pin into shift sector slot. Install
shift rail. Ensure shift rail is seated in shift forks. Rotate shift
sector so lock pin can be installed. Install lock pin so tapered end
is in fork and rail. Install plug. Install shift lever and nut on
shift sector shaft.
10) Install detent plunger, spring and plug. Install front
output shaft. Install drive chain and sprocket. Install drive sprocket
snap ring. Install front output shaft rear bearing.
11) Install oil seal in oil pump housing. Assemble oil pump
gears in housing. Ensure oil feed hole is aligned with hole in
housing. Install oil pump screws. Tighten to specification. Install

\003
TR AN SM IS SIO N R EM OVA L & IN STA LLA TIO N - M /T

1988 J e ep C hero ke e
1988 MANUAL TRANSMISSION REMOVAL
Jeep
Cherokee, Comanche, Grand Wagoneer, Pickup, Wagoneer,
Wrangler
REMOVAL & INSTALLATION
TRANSMISSION
Removal
1) Remove screws attaching shift lever boot to floorpan.
Slide boot over lever. On models with T-176 transmission, press and
turn shift lever retainer counterclockwise to release lever.
2) Remove lever, boot, spring and seat as an assembly. On all
models, raise vehicle and support with safety stands. Disconnect rear
drive shaft from transfer case and wire out of way.
3) DO NOT allow shaft to hang free, as damage to universal
joint may result. Disconnect front parking brake cable at equalizer.
Remove rear cable clip from crossmember.
4) Place a jack under clutch housing to support engine.
Remove rear crossmember from frame. Disconnect speedometer cable,
back-up light switch wire and 4WD indicator switch wire.
5) Disconnect transfer case vent hose. Disconnect front drive
shaft and wire out of way. On Wrangler, remove transfer case shift
lever by removing shifter shaft retaining nut.
6) Remove cotter pins retaining shift control link pins in
shift rods and remove pins. Remove shifter shaft and disengage shift
lever from shift control links. Move lever out of the way.
NOTE: On some models, shifter shaft must be unthreaded from shift
lever in order to be removed. On other models, shaft can be
removed by sliding it out of lever.
7) Remove cotter pin and washers connecting link to shift
lever. Separate link from lever. Support transmission and transfer
case with jack.
8) Remove bolts securing transmission to clutch housing and
remove transmission and transfer case. Separate transfer case and
transmission.
Installation
1) Install pilot bushing lubricating wick and align throw out
bearing with splines in driven plate hub. Shift transmission into gear
using shift lever or a long screwdriver. This prevents clutch shaft
from rotating during installation and makes clutch shaft-to-driven
plate spline alignment easier.
2) Mount transmission on transmission jack. Raise
transmission and align transmission clutch shaft with splines in
driven plate hub.
3) When transmission is seated on clutch housing, install and
tighten transmission-to-clutch housing bolts. Apply Permatex No. 3
sealer to both sides of replacement transmission output shaft and
transfer case input shaft splines.
4) To install transmission, reverse removal procedure. Adjust
clutch and shift linkage.
TORQUE SPECIFICATIONS

TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Transmission-to-Clutch Housing ..................... 55 (75)
Transmission Cover Bolts ..................... 55-65 (75-88)
Housing-to-Transmission Case ................. 40-45 (54-61)
Crossmember Attaching Bolts .................. 34-40 (46-54)
Filler Plug .................................. 13-15 (18-20)









\









\









\









\









\









\

Open solenoid pull-in See Testing in STARTER
wire article









\









\









\









\









\









\









\







Starter Does Not Weak battery or dead Charge or replace
Operate and cell battery as necessary
Headlights Dim
Loose or corroded battery Check that battery
connections connections are clean
and tight
Internal ground in See Testing in STARTER
starter windings article
Grounded starter fields See Testing in STARTERS
Armature rubbing on pole See STARTER article
shoes









\









\









\









\









\









\









\







Starter Turns Starter clutch slipping See STARTER article
but Engine
Does Not Rotate
Broken clutch housing See STARTER article
Pinion shaft rusted or See STARTER article
dry
Engine basic timing See Ignition Timing in
incorrect TUNE-UP article
Broken teeth on engine Replace flywheel and
flywheel check for starter pinion
gear damage









\









\









\









\









\









\









\







Starter Will Not Faulty overrunning See STARTER article
Crank Engine clutch
Broken clutch housing See STARTER article
Broken flywheel teeth Replace flywheel and
check for starter pinion
gear damage
Armature shaft sheared See STARTER article
or reduction gear teeth
stripped
Weak battery Charge or replace
battery as necessary
Faulty solenoid See On-Vehicle Tests in
STARTER article
Poor grounds Check all ground
connections for
tight and clean
connections
Ignition switch faulty Adjust or replace
or misadjusted ignition switch as
necessary









\









\









\









\









\









\









\







Starter Cranks Battery weak or Charge or replace
Engine Slowly defective battery as necessary

Engine overheated See ENGINE COOLING
SYSTEM article
Engine oil too heavy Check that proper
viscosity oil
is used
Poor battery-to-starter Check that all
connections between
battery and starter are
clean and tight
Current draw too low or See Bench Tests in
too high STARTER article
Bent armature, loose pole See STARTER article
shoes screws or worn
bearings
Burned solenoid contacts Replace solenoid
Faulty starter Replace starter









\









\









\









\









\









\









\







Starter Engages Engine timing too far See Ignition Timing in
Engine Only advanced TUNE-UP article
Momentarily
Overrunning clutch not Replace overrunning
engaging properly clutch. See STARTER
article
Broken starter clutch See STARTER article
Broken teeth on engine Replace flywheel and
flywheel check starter pinion
gear for damage
Weak drive assembly See STARTER article
thrust spring
Weak hold-in coil See Bench Tests in
STARTER article









\









\









\









\









\









\









\







Starter Drive Defective point assembly See Testing in STARTER
Will Not Engage article
Poor point assembly ground See Testing in STARTER
article
Defective pull-in coil Replace starter
solenoid









\









\









\









\









\









\









\







Starter Relay Dead battery Charge or replace
Does Not Close battery as necessary
Faulty wiring Check all wiring and
connections leading to
relay
Neutral safety switch Replace neutral safety
faulty switch
Starter relay faulty Replace starter relay