1988 JEEP CHEROKEE spark plugs

Disconnect throttle valve linkage on A/T models.
3) Remove coolant temperature sensor wire. Disconnect
throttle cable at bellcrank. Remove intake manifold bolts. Remove
intake manifold.
4) If exhaust manifold requires removal, raise and support
vehicle. Disconnect exhaust pipe. Remove oxygen sensor wire and remove
sensor. Remove manifold-to-cylinder head bolts. Remove exhaust
manifold.
Installation
1) Ensure all gasket surfaces are clean. Install manifolds
and gasket on cylinder head. Start all bolts and finger tighten.
Tighten bolts in proper sequence. See Fig. 1. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
2) Clean oxygen sensor threads. Apply anti-seize on oxygen
sensor threads prior to installation. Install sensor and tighten to
specification. Reverse removal procedures to complete installation.
Fill and purge cooling system. See COOLING SYSTEM AIR PURGE under
ENGINE COOLING.
Fig. 1: Manifold Bolt Tightening Sequence
CYLINDER HEAD
Removal
1) Disconnect negative battery cable. Drain cooling system.
Remove air cleaner. Remove intake and exhaust manifolds. See INTAKE &
EXHAUST MANIFOLDS.
2) Disconnect and mark all hoses and electrical connections
at cylinder head. Disconnect and mark spark plug wires. Remove spark
plugs. Remove valve cover bolts.

manifold.
3) Remove EGR tube fittings from manifolds. Remove power
steering pump and A/C compressor and mounting brackets (if equipped).
4) Remove intake manifold bolts. Remove intake manifold. If
exhaust manifold requires removal, disconnect exhaust pipe from
manifold. Remove oxygen sensor (if equipped). Remove exhaust manifold.\
Installation
1) Install new gasket. Install exhaust manifold and loosely
install bolts. Install intake manifold. Tighten bolts to specification
in proper sequence. See Fig. 2.
2) Apply anti-seize to oxygen sensor threads prior to
installation. Reverse removal procedure for remaining components.
Tighten bolts to specification. Fill and purge cooling system. See
COOLING SYSTEM AIR PURGE under WATER PUMP in this article.
Fig. 2: Manifold Tightening Sequence (4.2L)
Courtesy of Chrysler Motors.
CYLINDER HEAD
Removal
1) Disconnect negative battery cable. Drain cooling system.
Disconnect hoses at thermostat housing. Remove intake and exhaust
manifolds. See the following:
* INTAKE & EXHAUST MANIFOLD (4.0L) .
* INTAKE & EXHAUST MANIFOLD (4.2L) .
2) Disconnect and mark all hoses and electrical connections
at cylinder head. Disconnect and mark spark plug wires. Remove spark
plugs. Remove valve cover bolts.
3) Remove the rocker arms and the push rods. Remove cylinder
head bolts. Remove cylinder head. See ROCKER ARMS & BRIDGE.
Inspection
Inspect cylinder head for cracks or damage. Using
straightedge, check cylinder head for warpage in several areas. Repair

than .010" (.25 mm) from tip. Chamfer sharp edge of reground valve
tip. Recheck valve stem installed height.
VALVE STEM OIL SEALS
Valve stem oil seals must be installed on valve stem. See
Fig. 2 . Seals are needed due to pressure differential at the ends of
valve guides. Atmospheric pressure above intake guide, combined with
manifold vacuum below guide, causes oil to be drawn into the cylinder.
Exhaust guides also have pressure differential created by
exhaust gas flowing past the guide, creating a low pressure area. This
low pressure area draws oil into the exhaust system.
Replacement (On Vehicle)
Mark rocker arm or overhead cam components for location.
Remove rocker arm components or overhead cam components. Components
must be installed in original location. Remove spark plugs. Valve stem
oil seals may be replaced by holding valves against seats using air
pressure.
Air pressure must be installed in cylinder using an adapter
for spark plug hole. An adapter can be constructed by welding air hose
connection to spark plug body with porcelain removed.
Install adapter in spark plug hole. Apply a minimum of 140
psi (9.8 kg/cm
) to adapter. Air pressure should hold valve closed. If
air pressure does not hold valve closed, check for damaged or bent
valve. Cylinder head must be removed for service.
Using valve spring compressor, compress valve springs. Remove
valve locks. Carefully release spring compressor. Remove retainer or
rotator and valve spring. Remove valve stem oil seal.
If oversized valves have been installed, oversized oil seals
must be used. Coat valve stem with engine oil. Install protective
sleeve over end of valve stem. Install new oil seal over valve stem
and seat on valve guide. Remove protective sleeve. Install spring
seat, valve spring and retainer or rotator. Compress spring and
install valve locks. Remove spring compressor. Ensure valve locks
are fully seated.
Install rocker arms or overhead cam components. Tighten all
bolts to specification. Adjust valves if required. Remove adapter.
Install spark plugs, valve cover and gasket.
VALVE SPRING INSTALLED HEIGHT
Valve spring installed height should be checked during
reassembly. Measure height from lower edge of valve spring to the
upper edge. DO NOT include valve spring seat or retainer. Distance
must be within specifications. If valves and/or seats have been
ground, a valve spring shim may be required to correct spring height.
See Fig. 12 .
Fig. 12: Measuring Valve Spring Installed Height - Typical
This Graphic For General Information Only

CLUTCH PEDAL POSITION SWITCHES
COLD START INJECTORS
CONNECTORS
COOLANT
COOLANT RECOVERY TANKS
COOLING FAN MOTOR MODULES
COOLING FAN MOTOR RELAYS AND MODULES
COOLING FAN MOTOR RESISTORS
COOLING FAN MOTOR SENSORS AND SWITCHES
COOLING FAN MOTOR SWITCHES
COOLING FAN MOTORS
CRANKSHAFT POSITION SENSORS
DECEL VALVES
DEFLECTORS
DIP STICKS AND TUBES
DIP STICK TUBES
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR CAPS
DISTRIBUTOR RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ROTORS
DISTRIBUTOR SHIELDS
DISTRIBUTORS
EARLY FUEL EVAPORATION VALVES (HEAT RISER ASSEMBLIES)
EGR COOLERS
EGR EXHAUST MANIFOLD PASSAGES
EGR INTAKE AND EXHAUST MANIFOLD PASSAGES
EGR PLATES AND COOLERS
ELECTRONIC SPARK CONTROL MODULES
ELECTRONIC TRANSMISSION CONTROL DEVICES
ELECTRONIC TRANSMISSION FEEDBACK DEVICES
ENGINE COOLANT TEMPERATURE SENSORS
ENGINE COOLING SYSTEMS
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE OIL
ENGINE OIL CANISTERS
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL GASKETS
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER PURGE DEVICES
EVAPORATIVE EMISSION (EVAP) CANISTERS
EVAPORATIVE EMISSION (EVAP) FEEDBACK DEVICES
EXHAUST GAS RECIRCULATION DEVICES
EXHAUST GAS RECIRCULATION FEEDBACK DEVICES
EXPANSION PLUGS
FAN CONTROL SENSORS
FUEL
FUEL ACCUMULATORS AND DAMPERS
FUEL AND COLD START INJECTORS
FUEL DAMPERS
FUEL DELIVERY CHECK VALVES
FUEL DISTRIBUTORS (BOSCH CIS)
FUEL FILLER NECKS AND RESTRICTORS
FUEL FILTERS
FUEL INJECTORS
FUEL LEVEL SENDERS7
FUEL PRESSURE REGULATORS
FUEL PUMPS (IN-TANK AND EXTERNAL, ELECTRICAL OR MECHANICAL)
FUEL RAILS
FUEL RESTRICTORS

FUEL TANKS
GAS CAPS
GASKETS
GROMMETS (VALVE COVER)
HARMONIC DAMPERS
HEATER CONTROL VALVES
HEATER CORES
HOSE AND TUBE COUPLERS, CONNECTORS AND CLAMPS
HOSE CLAMPS
HOSE CONNECTORS
HOSE COUPLERS
HOSES AND TUBES (FUEL LINES, RADIATOR, VACUUM, BY PASS,
HEATER, RECOVERY TANK AND OIL COOLERS)
HOUSINGS
IDLE AIR CONTROLS
IDLE SPEED CONTROL ACTUATORS
IGNITION BOOTS
IGNITION COIL TOWERS
IGNITION COILS
IGNITION CONTROL MODULES (ICM)
IGNITION SWITCHES
IGNITION TERMINALS
IGNITION WIRES, BOOTS, COIL TOWERS AND TERMINALS (SECONDARY)
IN-TANK FUEL STRAINERS
INERTIA FUEL SHUT-OFF SWITCHES
INTAKE AIR TEMPERATURE SENSORS
INTAKE MANIFOLDS
INTERCOOLERS
KNOCK SENSORS
LIQUID VAPOR SEPARATORS
MANIFOLD ABSOLUTE PRESSURE (MAP) SENSORS
MASS AIR FLOW (MAF) SENSORS
METAL AIR MANIFOLDS AND PIPES
METAL AIR PIPES
MIX CONTROL SOLENOIDS
MOTOR MOUNTS
O-RINGS, GASKETS, SEALS AND SPRING LOCKS
O2 SENSORS
OIL PRESSURE SENDING UNITS
OIL PUMP PICK-UP SCREENS
OIL PUMPS
PARK NEUTRAL POSITION SWITCHES
PCV BREATHER ELEMENTS
PCV ORIFICES
PCV VALVES
PICK-UP ASSEMBLIES (INCLUDES MAGNETIC, HALL EFFECT AND
OPTICAL)
POWER STEERING PRESSURE SENSORS
POWERTRAIN CONTROL MODULES (PCM) AND PROM
POWERTRAIN CONTROL PROM
PRESSURIZED EXPANSION TANK CAPS
RADIATOR CAPS AND PRESSURIZED EXPANSION TANK CAPS
RADIATOR FAN BLADES
RADIATOR FAN CLUTCHES
RADIATORS
ROLL OVER VALVES
SEALING COMPOUNDS
SEALS
SECONDARY AIR INJECTION SYSTEM MANAGEMENT DEVICES
SENSORS AND ACTUATORS
SHROUDS, BAFFLES AND DEFLECTORS
SPARK PLUGS
SPRING LOCKS

Idle Speed Control Actuator ............................... ISC
Mix Control Solenoid .............................. MC Solenoid
Secondary Air Injection System Management Device .... AIR, PAIR
Vacuum Regulator Solenoid .................................. ..
Waste Gate Control Solenoid ................................ ..









\









\









\









\









\









\









\


SHROUDS, BAFFLES AND DEFLECTORS
SHROUD, BAFFLE AND DEFLECTOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect,
affecting cooling system
performance ............ A . Require repair or replacement.
Attaching hardware
broken ................. A .. Require repair or replacement
of hardware.
Attaching hardware
missing ................ C ......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Bent, affecting cooling
system performance ..... A . Require repair or replacement.
Blocked, affecting cooling
system performance ..... A . Require repair or replacement.
Broken, affecting cooling
system performance ..... A . Require repair or replacement.
Cracked, affecting cooling
system performance ..... A . Require repair or replacement.
Loose, affecting cooling
system performance ..... A ................ Require repair.
Loose, not affecting
cooling system
performance ............ 2 ................ Suggest repair.
Missing, affecting cooling
system performance ..... C ........... Require replacement.









\









\









\









\









\









\









\


SPARK PLUGS
NOTE: You are not required to replace spark plugs in sets.
However, you may suggest replacement of the other plugs
for preventive maintenance.
SPARK PLUG INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Electrode eroded ........ 1 ............ Suggest replacement.
Fouled .................. A ........... ( 1) Require repair or
replacement.
Gap incorrect ........... B .. Require repair or replacement.
Insulation broken ....... A ............. Require replacement
Insulator cracked ....... A ............ Require replacement.
Leaking compression ..... A .. Require repair or replacement.
Maintenance interval .... 3 ............ Suggest replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads

\003
IG NIT IO N S YSTE M - 4 .0 L W /S O LID S TA TE IG NIT IO N ( S SI)
1 988 J e ep C hero ke e
DISTRIBUTORS & IGNITION SYSTEMS
Jeep Solid State Ignition
4.0L 6-Cylinder
DESCRIPTION
IGNITION SYSTEM GENERAL DESCRIPTION
The Solid State Ignition (SSI) system features a solid state
Ignition Control Module (ICM)/ignition coil assembly, Electronic
Control Unit (ECU), distributor and engine speed sensor. Other
components include the battery, ignition switch, starter solenoid,
spark plugs and wires, cap and rotor, resistance wire, by-pass wire
and a knock sensor. A sync pulse signal generator (stator) inputs the
firing order to the ECU.
Fig. 1: 4.0L 6-Cylinder Firing Order
IGNITION CONTROL MODULE (ICM)
The ignition control module is mounted to the ignition coil.
See Fig. 2 . Based on control system inputs, the ECU triggers the
ignition coil via the ignition control module. The ECU is able to
advance or retard ignition timing by controlling the ignition coil
through the ignition control module.
The ICM consists of a solid state ignition circuit, an
integrated ignition circuit and an integrated ignition coil that can
be removed and serviced separately if necessary.

SPARK PLUG CHECK
Faulty or fouled plugs may perform well at idle speed, but at
higher engine speeds, they frequently fail. Faulty plug can exhibit
the following symptoms:
* Poor fuel economy.
* Power loss.
* Decreased engine speed.
* Hard starting.
* Generally poor performance.
Spark plugs also malfunction due to carbon fouling,
excessive electrode air gap, or broken insulators.
SYNC PULSE SIGNAL GENERATOR (STATOR) TEST
NOTE: For this test, an analog voltmeter MUST be used.
1) Insert the positive (+) lead of the voltmeter into the
Blue wire at the distributor connector.
2) Insert the negative (-) voltmeter lead into the Gray/Whit\
e
wire at the distributor connector.
CAUTION: DO NOT remove the distributor connector from distributor.
Insert the voltmeter leads into the backside of the
distributor connector to make contact with the terminals.
3) Set the voltmeter to the 15-Volt D/C scale. Turn ignition
key to "ON".
4) The voltmeter should display approximately 5.0 volts.
5) If no voltage displays, check that the voltmeter leads are
making good contact. If there is still no voltage, go to next step.
6) Remove the ECU and check for voltage at pin "C-16" and
ground with harness connected. If there in still no voltage, proceed
to the next step.
7) Connect Diagnostic Tester M.S. 1700 to the vehicle. Using
the diagnostic tester, perform vehicle test. If voltage is present, go
to the next step.
8) Check for continuity between the Blue wire at the
distributor connector and pin C-16 at the ECU.
9) If there in no continuity, repair harness as necessary.
10) Check for continuity between the Gray/White wire at the
distributor connector and pin C-5 at the ECU.
11) If there is no continuity, repair harness as necessary.
12) Check for continuity between the Black wire at the
distributor connector and ground.
13) If there is no continuity, repair harness as necessary.
14) While observing the voltmeter, crank the engine; the
voltmeter needle should fluctuate back and forth while the engine in
cranking. A fluctuation verifies that the stator in the distributor is
operating properly.
15) If there is no pulse sync, replace the stator. Refer to
REMOVAL & INSTALLATION below in this article.
REMOVAL & INSTALLATION
COOLANT TEMPERATURE SENSOR (CTS)
Removal
1) Drain the cooling system.