1988 JEEP CHEROKEE battery location

Removal
1) Remove PCV valve hose at valve cover. Remove valve cover
bolts. Using a razor knife, cut RTV sealant along valve cover. Pry
upward on valve cover in areas marked "PRY HERE" near bolt hole areas.
2) Remove valve cover. Alternately loosen each rocker arm
bolt one turn at a time. Remove rocker arm assemblies and push rods.
Mark components for reassembly. Components must be installed in
original location.
Installation
Reverse removal procedures. Install rocker arm components in
original location. Tighten bolts to specification. Apply RTV sealant
on valve cover prior to installation.
VALVE SPRINGS
Valve springs can be removed without removing cylinder head.
Valve Spring Installed Height
Information not available from manufacturer.
HYDRAULIC VALVE LIFTERS
Removal
Remove rocker arms and push rods. See ROCKER ARMS & BRIDGE.
Using Lifter Remover/Installer (J-21884), remove lifter through push
rod openings of cylinder head. Mark lifter location for reassembly
reference. Replace lifters as an assembly if damaged. Internal
components cannot be interchanged.
Inspection
Inspect lifter and camshaft mating surfaces for wear. Check
cylinder block lifter bore diameter. Lifter bore diameter should be
within .9055-.9065" (22.999-23.025 mm). Replace parts as necessary.
Installation
Soak lifter assembly in engine oil supplement prior to
installation. Reverse removal procedures for installation. Install
lifter in original location.
ENGINE FRONT COVER
Removal
1) Disconnect negative battery cable. Remove drive belts, fan
and hub assembly. Remove pulley from vibration damper. Remove
vibration damper retaining bolt and washer.
2) Using Puller (J-21719-01), remove vibration damper and
key. Remove oil pan-to-front cover bolts. Remove cover-to-block
retaining bolts. Remove front cover.
3) Cut oil pan gasket even with face of cylinder block.
Remove gasket from oil pan. Pry crankshaft oil seal from cover.
Installation
1) Ensure all gasket surfaces are clean. Ensure oil slinger
is installed on crankshaft. Apply sealing compound on both sides of
front cover gasket. Install gasket on cylinder block. Replace front
section of oil pan seal with similar section fabricated from new seal.
2) Coat seal with RTV sealant and place in position. Apply
sealant to the joint area of oil pan and cylinder block. Place front
cover on cylinder block. Place Front Cover Seal Installer (J-22248) in\
front cover seal area.
3) Install all retaining bolts. Tighten bolts to

Fig. 4: Location of ECU-Controlled Relays
Load Swap Relay
The Load Swap Relay is used on models with A/C and power
steering. The relay works in conjunction with the power steering
pressure switch to disengage the A/C compressor clutch.
If the compressor clutch is engaged when the power steering
pressure switch contacts close, the input signal from the switch to
the ECU also activates the load swap relay. The relay contacts open,
cutting off electrical feed to the compressor clutch. The clutch
remains disengaged until the pressure switch contacts reopen and
engine idle returns to normal.
NOTE: The load swap relay does not reengage the compressor clutch
immediately. The relay has a timer that delays energizing
the clutch for .5 second to ensure smooth engagement.
Fuel Pump Control Relay
Battery voltage is applied to the relay through the ignition
switch. The relay is energized when a ground is provided by the ECU.
When energized, voltage is applied to the fuel pump See Fig. 15.
A/C Clutch Relay

VALVE SPRING
Valve springs can be removed without removing cylinder head.
Valve Spring Installed
For 4.0L the Valve Spring Installed Height Specification is
1.625 inches or 41.29 mm. For the 4.2L the information is not
available from manufacturer.
HYDRAULIC VALVE LIFTER
Removal
Remove cylinder head. See CYLINDER HEAD. Using Lifter
Remover/Installer (J-21884), remove lifter. Mark lifter location for
reassembly reference. Replace lifters as an assembly if damaged.
Internal components cannot be interchanged.
Inspection
Inspect lifter and camshaft mating surfaces for wear. Check
cylinder block lifter bore diameter. Lifter bore diameter should be
within .9055-.9065" (22.999-23.025 mm). Replace parts as necessary.
Installation
Soak lifter assembly in engine oil prior to installation.
Reverse removal procedure for installation. Install lifter in original
location.
ENGINE FRONT COVER
Removal
1) Disconnect negative battery cable. Remove drive belts, fan
and hub assembly. Remove pulley from vibration damper. Remove
vibration damper retaining bolt and washer.
2) Using Puller (J-21719-01), remove vibration damper and
key. Remove alternator and A/C compressor bracket (if equipped).
Remove oil pan-to-front cover bolts. Remove cover-to-block retaining
bolts. Remove front cover.
3) Cut oil pan gasket tabs even with face of cylinder block.
Remove tabs. Remove gasket from oil pan. Pry crankshaft oil seal from
cover.
Installation
1) Ensure all gasket surfaces are clean. Ensure oil slinger
is installed on crankshaft. Apply sealing compound on both sides of
front cover gasket. Install gasket on cylinder block. Replace front
section of oil pan seal with similar section fabricated from new seal.
2) Coat seal with RTV sealant and place in position. Apply
sealant to the joint area of oil pan and cylinder block. Apply engine
oil on seal-to-oil pan contact areas.
3) Place front cover on cylinder block. Place Front Cover
Seal Installer (J-22248) in front cover seal area. Install all
retaining bolts. Tighten bolts to specification.
4) Install front cover oil seal. See FRONT COVER OIL SEAL in
this article. Remove front cover seal installer. Reverse removal
procedure for remaining components. Lubricate vibration damper
retaining bolt with oil prior to installation. Tighten bolts to
specification.
FRONT COVER OIL SEAL
1) Remove vibration damper. Pry seal from front cover. Use

panel to gain access to blower motor mounting screws.
2) Remove screws attaching evaporator housing to instrument
panel and mounting bracket. Lower evaporator housing and pull hoses
and grommet through opening.
Installation
To install, reverse removal procedure. Evacuate, leak test,
recharge and check A/C system for proper operation.
EXPANSION VALVE
Removal (Cherokee, Comanche & Wagoneer)
Discharge A/C system using approved refrigerant
recovery/recycling equipment. Disconnect A/C hoses from expansion
valve. Disconnect expansion valve from evaporator core inlet and
outlet tubes. Remove expansion valve.
Installation
To install, reverse removal procedure. Evacuate, leak test,
recharge and check A/C system operation.
NOTE: The expansion valve is pre-set and should not be adjusted. A
faulty valve requires replacement.
Removal (Wrangler)
1) Discharge system using approved refrigerant
recovery/recycling equipment. Remove evaporator housing. Remove
insulation wrapped around suction line and expansion valve.
2) Mark capillary tube location on suction line. Disconnect
inlet and outlet connections, capillary tube clamp and equalizer tube.
Remove expansion valve.
Installation
1) Clean suction line to provide positive contact with
replacement expansion valve capillary tube. Connect inlet and outlet
hoses. Clamp capillary tube securely at marked position and connect
equalizer tube.
2) Wrap expansion valve and line with insulation. Install
evaporator housing assembly. Evacuate, leak test, recharge and check
A/C system operation.
TEMPERATURE CONTROL THERMOSTAT
Removal (Cherokee, Comanche & Wagoneer)
1) Disconnect battery ground. Remove console (if equipped).
Remove lower instrument panel. Disconnect electrical connection at
thermostat. See Fig. 3.
2) Remove capillary tube retaining screw. Remove thermostat
retaining screws. Remove capillary tube from tube guide hole.
Installation
1) To install, feed capillary tube through tube guide hole
until Red tape on capillary tube just enters hole in housing. Install
capillary tube retaining screw and clip.
2) Install thermostat retaining screws and attach electrical
connection. To complete installation, reverse removal procedure.
CAUTION: Handle capillary tube with care to avoid bends or kinks
which could cause thermostat to malfunction.
Removal (Wrangler)
Remove evaporator housing assembly. Remove lower cover.

\003
EN G IN E R EM OVA L - 4 -C YL

1988 J e ep C hero ke e
1988 ENGINES
Jeep - Engine Removal - 4-Cylinder
Cherokee, Comanche, Wrangler
4-CYLINDER ENGINES
2.5L
1) Disconnect negative battery cable. Drain cooling system.
Remove air cleaner, lower radiator hose, fan shroud, and engine
compartment light from hood. Scribe hinge locations and remove hood.
Disconnect automatic transmission cooler lines at radiator (if
equipped).
2) Remove upper radiator hose, fan assembly and coolant
recovery hose. Remove radiator and A/C condenser (if equipped). Hold
fan pulley to water pump flange using 5/16" x 1/2" SAE capscrew.
Disconnect heater hoses, throttle linkages, cruise control cable (if
equipped) and Throttle valve rod.
3) Disconnect wires from starter and separate CEC system
wiring harness connector. Disconnect fuel pipe from fuel pump and fuel
return hose from fuel filter. Disconnect hoses from A/C compressor and
power steering pump (if equipped). Drain power steering pump
reservoir. Cap all fittings and hose ends.
4) Remove vacuum check valve from brake booster (if
equipped). Tag and remove all wiring and vacuum lines connected to
engine or accessories. Raise vehicle and remove starter. Disconnect
exhaust pipe from manifold.
5) Remove converter/flywheel housing cover. Remove engine
mount nuts at bracket side. On automatic transmission models, index
mark drive plate and torque converter. Remove drive plate-to-converter
bolts.
6) Remove upper and loosen lower bellhousing-to-engine bolts.
Attach lifting equipment to engine. Raise engine off front mounts,
Place support under bellhousing. Remove remaining bellhousing-to-
engine bolts. Lift engine out of engine compartment.
NOTE: Engine mount pads may be removed from engine brackets to
align engine and transmission during installation.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Ft. Lbs. (N.m)
Clutch Housing-to-Block Bolts .................... 55 (75)
Drive Plate-to-Converter ......................... 26 (35)
Flywheel Bolts ............................... ( 1) 50 (68)
Front Support Bracket-to-Block ................... 45 (61)
Front Support Cushion-to-Crossmember ............. 33 (45)
Rear Support Bracket-to-Transmission ............. 33 (45)
Rear Support Cushion-to-Bracket .................. 30 (41)
Starter Motor-to-Block ........................... 33 (45)
( 1) - Tighten an additional 60 degrees.









\









\









\









\









\









\

\003
EN G IN E R EM OVA L - 6 -C YL

1988 J e ep C hero ke e
1988 ENGINES
Jeep - Engine Removal - 6-Cylinder
Cherokee, Comanche, Wagoneer, Wrangler
6-CYLINDER ENGINES
4.0L
1) Scribe hinge locations, remove engine compartment light
(if equipped) and remove hood. Disconnect battery cables and remove
battery. Drain cooling system.
2) Disconnect wire connectors from alternator, ignition coil
and distributor. Disconnect oil pressure sender wire, starter wires
and fuel injector wiring harness (if equipped). Detach 2 fuel pipe
quick connect couplings at left inner fender panel. Disconnect engine
ground strap and remove air cleaner.
3) Disconnect the vacuum purge hose at fuel vapor canister
tee. Disconnect wire from idle speed actuator and oxygen sensor.
Detach throttle cable from bracket and disconnect throttle valve rod
at bellcrank. Remove upper and lower radiator hoses.
4) On automatic transmission models, disconnect the
transmission fluid cooler tubing. On all models, remove fan shroud and
radiator. Remove fan and spacer or Tempatrol fan assembly. Hold fan
pulley to water pump flange using 5/16" x 1/2" SAE capscrew while
crankshaft is rotated.
5) Disconnect cruise control cable (if equipped). Disconnect\
wires from starter motor solenoid and disconnect CEC system harness.
Remove power brake vacuum check valve from booster (if equipped).
6) Disconnect power steering hoses from steering gear (if
equipped). Drain power steering pump reservoir and plug end of hoses.
Cap all fittings on steering gear and hoses. Raise and support
vehicle. Remove starter. Remove flywheel housing access cover.
7) Remove upper and loosen lower bellhousing-to-engine bolts.
Attach lifting equipment to engine. Raise engine off front mounts.
Place support under bellhousing. Remove remaining bellhousing-to-
engine bolts. Lift engine out of engine compartment.
4.2L
1) Remove battery and drain cooling system. Remove air
cleaner and engine compartment light from hood. Scribe hinge location
and remove hood. Disconnect and plug front fuel line at pump and fuel
return line at frame.
2) Disconnect heater hoses at heater. Label and disconnect
all wiring, lines, linkage and hoses at engine. Remove vacuum switch
assembly bracket from cylinder head cover. Remove both radiator hoses
and automatic transmission oil lines (if equipped) at radiator. Remove\
radiator and shroud.
3) Remove fan and spacer. Use 5/16" x 1/2" SAE bolt to hold
fan pulley to water pump flange. Remove starter and disconnect engine
ground strap. Remove engine mount-to-bracket nuts. Disconnect exhaust
pipe at manifold.
4) Discharge A/C system (if equipped). Disconnect and plug
hose or port openings at compressor. Disconnect hoses at power
steering gear and drain reservoir. Remove power brake vacuum check
valve. Remove bracket bolt for automatic transmission filler tube (if
equipped).
5) Lift and support vehicle. On models with automatic

\003
FU EL P U M P - E LE C TR IC

1988 J e ep C hero ke e
1988 Electric Fuel Pump
JEEP
2.5L TBI, 4.0L MPFI
DESCRIPTION & OPERATION
Fuel system on 2.5L TBI models operate under constant fuel
pressure of 14.5 psi (1.02 kg/cm). Fuel pressure regulator is
mounted on throttle body assembly. Excess fuel pressure is returned
to fuel tank. ECU has no control over fuel pressure relief valve.
Fuel pump is immersible type with permanent magnet electric motor.
A frame mounted in-line fuel filter is used. Fuel pump is
attached to fuel gauge sending unit in fuel tank. Voltage to operate
pump is controlled by Electronic Control Unit (ECU). A ballast
resistor is used in the fuel pump control circuit.
Ballast resistor is by-passed during start mode. During
running mode, ballast resistor reduces speed of pump by lowering pump
voltage. This ensures normal speed in running mode. The 1-ohm ballast
resistor is mounted on right side of plenum chamber.
Fuel pump control relay is located on front of right strut
tower. Battery voltage is supplied to relay from ignition switch.
Relay is energized when ECU provides a circuit to ground.
A multi-cell, roller type pump is used on all 4.0L MPFI
models. Pump and fuel filter are located on a plate, forward of rear
axle. Fuel pump control relay location for 4.0L models is on right
inner front fenderwell. Battery voltage is supplied to relay from
ignition switch. Relay is energized when ECU provides a circuit to
ground.
Pump contains 2 check valves. One valve relieves internal
pump pressure and regulates maximum pump output. Second valve,
located near pump outlet, restricts fuel movement in either direction
when pump is not in operation. System operates under a constant fuel
pressure of 31 psi (2.17 kg/cm
).
Fig. 1: 2.5L Fuel Pump & Fuel Gauge Sending Unit
Courtesy of Chrysler Motors.

2.5L TBI
1) Adjustment of fuel pressure is required after replacement
of pressure regulator. Remove air inlet from throttle body. Connect
tachometer to diagnostic connector terminals D1-1 and D1-3. Connect
fuel pressure gauge to fuel body pressure test fitting.
NOTE: Some TBI models do not have a pressure test fitting on
throttle body. Use Fitting (PN 8983 501 572) for this
purpose.
2) Start engine and accelerate to 2000 RPM. Turn adjustment
screw to obtain 14.5 psi (1.02 kg/cm
) fuel pressure. Location of
adjustment screw is on bottom of regulator. Install lead seal ball to
cover regulator adjustment screw after adjusting fuel pressure to
specification. Turn ignition off. Disconnect fuel pressure gauge.
Install cap on test fitting. Install air inlet.
NOTE: To increase fuel pressure, turn adjustment screw inward. To
decrease fuel pressure, turn adjustment screw outward.
4.0L MPFI
1) Remove cap from pressure test port in fuel rail. Connect
Fuel Pressure Gauge (J-37730-1) to pressure fitting. Start vehicle.
Pressure should be approximately 31 psi (2.7 kg/cm
) with vacuum
hose connected to pressure regulator.
2) Pressure should be 39 psi (2.74 kg/cm
) with vacuum
hose removed from regulator. If fuel pressure is not to
specifications, check for kinks or restricting bends in fuel supply
and return lines. Check fuel pump flow rate. Pump should deliver
minimum of 1.06 quarts (one liter) of fuel per minute with fuel
return line pinched off.
3) If flow is inadequate, check system for plugged fuel
filter or filter sock. Fuel pump flow rate can be checked by
connecting a hose to fuel test port on fuel rail and inserting other
end in clean container.
4) To operate fuel pump, install a jumper wire into
diagnostic connector terminals D1-5 and D1-6. Pinch off fuel return
line to ensure that no fuel returns to fuel tank. If fuel pressure is
still not to specifications and fuel flow is normal, replace
regulator.
REMOVAL & INSTALLATION
FUEL PUMP
Removal (2.5L TBI)
1) Disconnect battery cables. Ensure fuel level is less than
1/2 for this procedure. Remove fuel outlet and return hoses. Remove
sending unit wires. Remove sending unit retaining lock ring.
2) Remove sending unit/pump assembly with "O" ring seal.
Disconnect fuel hose from fuel pump. Disconnect wires from fuel pump.
Remove fuel pump from sending unit.
Installation
Clean seal contact are of fuel tank. Install new "O" ring
seal. Install a new filter on end of suction tube. Position sending
unit/pump assembly in tank. To complete installation, reverse removal
procedure. Start engine and check for leaks.
CAUTION: Fuel leaks can develop from over tightening sending
unit/pump during installation.