1988 JEEP CHEROKEE Split
[x] Cancel search: SplitPage 363 of 1378
\003
DIF FE R EN TIA L - D AN A T R AC -L O K & P O W ER -L O K
1988 J e ep C hero ke e
1988 Positive Traction Differentials - Dana Power-Lok &
Trac-Lok
Jeep
DESCRIPTION
The limited slip differential uses 2 sets of multiple disc
clutches to control differential action. Dana produces 2 types of
positive traction differentials. The Power-Lok 4-pinion differential
is a split-case type. The Trac-Loc 2-pinion differential is a single-
case type.
OPERATION
When one or both wheels are on a low-traction surface such as
snow, ice or mud, the friction between the clutch plates will transfer
a portion of the usable torque to the wheel with the most traction.
The wheel on ice or snow will have a tendency to operate with the
opposite wheel in a combined driving effort.
AXLE RATIO & IDENTIFICATION
To determine axle ratio, see DRIVE AXLE RATIO IDENTIFICATION
in this section.
LUBRICATION
NOTE: Always use special positive traction differential lubricant
as specified by manufacturer.
DIAGNOSIS & TESTING
DANA 2-PINION TRAC-LOK
1) Drive vehicle to thoroughly warm up lubricant in rear
axle. Place a piece of slick paper over a smooth formica board. Ensure
formica board is on flat and level floor.
Fig. 1: Exploded View of Jeep Single-Case Dana Trac-Lok Differential
Page 364 of 1378
Fig. 2: Exploded View of Split Case (4-Pinion)
2) Drive vehicle over formica board until one rear wheel is
in the center of board and paper. Place a block of wood 2" high and a
minimum of 3" wide in front of one of the front wheels.
3) Open throttle gradually attempting to slowly drive vehicle
over block of wood. If paper slips out of position, reposition paper
and repeat test. If vehicle drives over block of wood, axle is
functioning properly.
DANA 4-PINION POWER-LOK
1) With engine off and transmission in "N", raise one wheel
off ground. Block both front and rear wheels of opposite side. Install
adapter tool across 2 wheel studs and attach torque wrench to center
of tool.
2) Observe torque required to continuously turn wheel
smoothly through several revolutions. Repeat test for opposite side.
If differential is okay, torque should be 40-200 ft. lbs. (54-272 N.
m). Disregard breakaway torque. Use rotating torque only.
NOTE: Exploded view of Chrysler Motors Trac-Lok differential was
not available from manufacturer.
REMOVAL & INSTALLATION
See DANA SEMI-FLOATING or FULL-FLOATING AXLE article in this
section.
OVERHAUL
DANA 2-PINION TRAC-LOK
NOTE: For front axle shaft and bearing removal, see articles on
DANA FULL-FLOATING AXLES or 4WD STEERING KNUCKLES in this
section. With the exception of ring gear and differential
side bearings, Chrysler Motors does not recommend disassembly
of differential. If repair is required, manufacturer
recommends replacing entire unit as an assembly.
Disassembly (Jeep)
1) Using 2 screwdrivers, remove pinion snap rings. Using a
brass drift and a hammer, remove pinion shaft from case. Install Step
Page 445 of 1378
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads if
available; otherwise, replace
bushing.
Attaching hardware threads
stripped (threads
missing) ............... A ..... Require replacement of part
with stripped threads if
available; otherwise, replace
bushing.
Binding ................. A .. Require repair or replacement.
Contaminated ............ 1 ............ Suggest replacement.
Deteriorated, affecting
performance ............ A .. Require repair or replacement.
Distorted, affecting
performance ............ A .. Require repair or replacement.
Missing ................. A ............ Require replacement.
Noisy ................... 2 .......... (1) Further inspection
required.
Rubber separating from
internal metal sleeve on
bonded bushing ......... A ............ Require replacement.
Seized .................. A ............ Require replacement.
Shifted (out of
position) .............. B .. Require repair or replacement.
Split ................... A ............ Require replacement.
Surface cracking (weather-
checked) ............... .. ........ No service suggested or
required.
Worn, affecting
performance ............ A .. Require repair or replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
( 1) - If noise isolated to bushing, suggest repair or
replacement.
CAUTION: Use only approved lubricant on rubber bushings.
Petroleum-based lubricants may damage rubber bushings.
\
\
\
\
\
\
\
CABLES (SPEEDOMETER)
CABLE (SPEEDOMETER) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bent .................... A .. Require repair or replacement.
Binding ................. A .. Require repair or replacement.
Bracket bent, affecting
performance ............ A .. Require repair or replacement.
Bracket bent, not
affecting performance .. .. ........ No service suggested or
Page 463 of 1378
Scored .................. B ............ Require replacement.
Spring rate less than
specifications ......... B ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
Worn beyond
specifications ......... B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
\
\
\
\
\
\
\
PRESSURE SWITCHES
See SWITCHES.
RACES
See BEARINGS AND RACES .
RUBBER JOINTS (METALASTIC)
These joints may be found on half and/or drive shafts. They
are usually found on European vehicles featuring a three-lug drive
flange. They may be equipped with a centering ball or pin.
RUBBER JOINT (METALASTIC) INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Drive flange bent ....... A ............. Require repair or
replacement.
Drive flange damaged,
affecting performance .. A ............ Require replacement.
Rubber drive joint
cracked ................ 2 ............ Suggest replacement.
Rubber drive joint
damaged, affecting
performance ............ A ............ Require replacement.
Rubber drive joint split
between mounting holes . A ............ Require replacement.
Rubber drive joint torn at
mounting holes ......... A ............ Require replacement.
Rubber drive joint weather-
cracked ................ .. ........ No service suggested or
required.
\
\
\
\
\
\
\
SCREENS
See FILTERS AND SCREENS .
SEALS
SEAL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Leaking ................. A ........... ( 1) Require repair or
replacement.
( 1) - Require inspection of mating and sealing surface and
repair or replace as necessary. Check vent. A plugged
Page 644 of 1378
lightly into its seat. Using seal installer, fully seat seal in
bearing cap or cylinder block.
Trim seal ends even with block parting surface. Some
applications require sealer to be applied on main bearing cap prior
to installation. See Fig. 28.
Fig. 28: Typical Rope Seal Installation
This Graphic For General Information Only
Split-Rubber Type Seal
Follow manufacturers procedures when installing split-rubber
type rear main oil seals. Installation procedures vary with engine
type. See appropriate ENGINE article in this section. See Fig. 29.
Fig. 29: Typical Split-Rubber Seal Installation
This Graphic For General Information Only
OIL PUMP
Page 769 of 1378
leaking) ............... A ............ Require replacement.
Sound quality
unsatisfactory ......... 2 .. Suggest replacement to address
customer need and/or request.
Split (exhaust leaking) . A ............ Require replacement.
Weak due to corrosion, but
no leaks present ....... 1 ............ Suggest replacement.
\
\
\
\
\
\
\
Page 1065 of 1378
NOTE: All other models are not adjustable.
BALL JOINTS
Jeep, Truck & Wagoneer
1) Raise vehicle and remove front wheels. Disconnect
steering damper and connecting rod. Remove cotter pin from right side
tie rod retaining nut. Rotate steering knuckles through complete arc
several times.
2) Place torque wrench on right side tie rod retaining nut.
Torque to turn knuckles through complete arc should not be more than
25 ft. lbs. (34 N.m).
3) If turning effort is excessive, disconnect tie rod ends
at knuckles. Measure turning effort of right and left side knuckles.
Individual turning effort should not be more than 10 ft. lbs. (14
N.m).
4) If individual turning effort is more than specified,
replace upper ball joint split ring seat. If turning effort is more
than 10 ft. lbs. (14 N.m) after split ring seat replacement, ball
joints will have to be replaced.
TURNING ANGLE
Truck & Wagoneer
1) Turning angle stop screws are located at rear of steering
knuckle, just above axle centerline. To adjust, loosen lock nut on
turning angle stop screw. Jeep turning angle is not adjustable.
2) Using turntable to measure angle, adjust stop screw to
obtain specified angle. Tighten lock nut without changing setting.
TURN ANGLE ADJUSTMENT
TURNING ANGLE ADJUSTMENT TABLE \
\
\
\
\
\
\
Application Left Right
Wheel Wheel
Jeep
Cherokee,
Comanche,
& Wrangler .......... ( 1) 32-33
................. ( 1) 32-33
Wagoneer ................. 36-37 ....................... 36-37
(1) - Angle stops are not adjustable. Parts must be replaced if
angle is incorrect.
\
\
\
\
\
\
\
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
\
Application Ft. Lbs.(N.m)\
Ball Joint Type
Lower Ball Joint Nut
Jeep .................................................. 100 (136)\
Upper Ball Joint Nut
Jeep .................................................. 100 (136)\
Upper Ball Joint Split Retaining Seat
Jeep ..................................................... 50 (68)\
\
\
\
\
\
\
\
Page 1077 of 1378
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Dust boot missing ....... 2 ........ (1) Suggest replacement.
Dust boot split ......... 2 ........ ( 1) Suggest replacement.
Dust boot torn .......... 2 ........ ( 1) Suggest replacement.
Housing cracked ......... A ............ Require replacement.
Lead routing incorrect .. B .. Require rerouting according to
vehicle manufacturer's
specifications.
Loose ................... B ... Require adjustment to vehicle
manufacturer's specifications.
Missing ................. C ............ Require replacement.
Output signal incorrect . A .. Require repair or replacement.
Wire lead damaged ....... A .. Require repair or replacement.
( 1) - This condition can lead to damage of the sliding magnet,
which, in turn, causes premature sensor failure.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - MODULES
AIR RIDE SUSPENSION - MODULE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Housing cracked ......... 2 .. Suggest repair or replacement.
Inoperative ............. A ............ Require replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - RELAYS (COMPRESSOR)
AIR RIDE SUSPENSION - RELAY (COMPRESSOR) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Housing cracked ......... 2 ........ ( 1) Suggest replacement.
Intermittent ............ A ............ Require replacement.
Missing ................. C ............ Require replacement.
Output signal incorrect . A ............ Require replacement.
( 1) - If moisture enters the relay, it can reduce life
expectancy or impair function.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - SWITCHES (ON/OFF)