1988 JEEP CHEROKEE fuel

Fig. 4: Location of ECU-Controlled Relays
Load Swap Relay
The Load Swap Relay is used on models with A/C and power
steering. The relay works in conjunction with the power steering
pressure switch to disengage the A/C compressor clutch.
If the compressor clutch is engaged when the power steering
pressure switch contacts close, the input signal from the switch to
the ECU also activates the load swap relay. The relay contacts open,
cutting off electrical feed to the compressor clutch. The clutch
remains disengaged until the pressure switch contacts reopen and
engine idle returns to normal.
NOTE: The load swap relay does not reengage the compressor clutch
immediately. The relay has a timer that delays energizing
the clutch for .5 second to ensure smooth engagement.
Fuel Pump Control Relay
Battery voltage is applied to the relay through the ignition
switch. The relay is energized when a ground is provided by the ECU.
When energized, voltage is applied to the fuel pump See Fig. 15.
A/C Clutch Relay

The ECU controls the A/C compressor clutch by means of the
A/C clutch relay. See Fig. 15.
UP-SHIFT INDICATOR LAMP
Manual transaxle vehicles are equipped with an up-shift
indicator lamp. The lamp is normally turned on when the ignition
switch is turned "ON", and is turned off when the engine starts.
The lamp will again light during engine operation, according
to engine speed and load conditions. A switch, located on the
transaxle, prevents lamp from lighting when transmission is shifted
to the next highest gear. If the shift of gears is not performed, the
ECU will turn the lamp off after 3-5 seconds.
MODES OF OPERATION
IGNITION SWITCH "ON" MODE
When the TBI system is activated by the ignition switch, the
system power relay is energized, and the fuel pump is energized by
the ECU through the fuel pump relay. The pump will operate for
approximately 1 second, unless the engine is operating or the starter
motor is engaged.
The ECU receives input from the CTS, MAT, and MAP sensors.
The up-shift indicator lamp is illuminated.
ENGINE START-UP MODE
When the starter motor is engaged, the ECU receives inputs
from the CTS and speed sensors, the starter motor relay, and the wide
open throttle switch. The fuel pump is activated by the ECU and
voltage is applied to the injector, with the ECU controlling
injection time.
The ECU determines proper ignition timing from the speed
sensor input. If the wide open throttle switch is engaged, the ECU
will deactivate the injector to prevent flooding.
ENGINE WARM-UP MODE
The ECU receives inputs from the CTS, MAT, MAP, speed, and
knock sensors. It also is informed of throttle, gear (automatic
transaxle models) and A/C control position.
The ECU provides a ground for the injector, precisely
controlling fuel delivery to the engine. The ECU also controls
ignition timing, engine idle speed and throttle stop angle. On
vehicles with manual transmissions, the up-shift indicator lamp is
controlled according to engine speed and load.
CRUISE MODE
During cruising speed, the ECU receives inputs from the CTS,
MAT, MAP, EGO, speed and knock sensors. It is also informed of
throttle, gear (automatic transaxle models), and A/C control position.\
The ECU provides a ground to the injector, precisely
controlling injector time. It also controls idle speed, throttle stop
angle, ignition timing, air/fuel mixture ratio and up-shift indicator
lamp.
DECELERATION MODE
During deceleration, the ECU receives inputs from the CTS,

MAT, MAP, EGO, speed and knock sensors. It also is informed of
throttle, gear (automatic transaxle models) and A/C control position.
When the ECU receives deceleration input from the closed
throttle (idle) switch, it grounds the EGR valve/canister purge
solenoid. This interrupts vacuum to EGR valve and canister purge
function. The injector is grounded, and during rapid deceleration,
the ECU may stop injection for a short period of time. The ECU also
controls engine idle speed and throttle stop angle.
WIDE OPEN THROTTLE MODE
During wide open throttle mode, the ECU receives inputs from
the CST, MAT, MAP, EGO, speed and knock sensors. It also monitors
throttle position.
When the ECU receives deceleration input from the closed
throttle (idle) switch, it grounds the EGR valve/canister purge
solenoid. This interrupts vacuum to EGR valve and canister purge
function. The EGO sensor input is not accepted by the ECU. The
injector is grounded and amount of fuel is precisely controlled.
IGNITION SWITCH "OFF" MODE
When ignition switch is turned "OFF", the ECU ceases to
provide ground for the injector and all fuel injection stops. The ECU
causes the idle speed actuator to fully extend for the next start up.
The ECU then deactivates.
COMPONENT TESTING
NOTE: When test calls for volt-ohmmeter, use of a high impedance
digital type is required.
Fig. 5: Diagnostic Connectors D1 and D2 Terminal Identification
1) Disconnect wiring harness connector from the MAT sensor.
Test resistance of the sensor with an ohmmeter. If resistance is not
185-100,700 ohms (3400 ohms at 70
F; 1600 ohms at 100F), replace

1) If all components have been checked and/or repaired, but
a system failure or problem still exists, the ECU may be at fault.
However, the ECU is a very reliable unit and must always be the final
component replaced if a doubt exists concerning the cause of a system
failure.
2) The only way to confirm an ECU malfunction is to take the
unit to an AMC dealer to have it tested. This is the only sure way to
avoid replacing a good ECU.
SYSTEM DIAGNOSIS
PRELIMINARY CHECKS
Be sure fuel is actually reaching the injector. Make sure no
air is entering the intake or exhaust system above the catalytic
converter. Before assuming an engine control system malfunction,
inspect the following systems to ensure components are in good
condition and are operating properly.
* All support systems and wiring.
* Battery connections and specific gravity.
* Electrical and vacuum connections on components and sensors.
* Emission control devices.
* Ignition system.
* Vacuum hoses.
CAUTION: Never connect or disconnect a component without turning the
ignition switch off. Never apply more than 12 volts or AC
voltage to system terminals. Disconnect battery cables
before charging it. Remove ECU if temperatures are expected
to exceed 176
F (80C), such as in a paint shop bake oven.
DIAGNOSTIC TEST CHARTS
Following are 6 different diagnostic test flow charts,
providing the shortest means of testing the system. These include:
* Ignition Switch "OFF" Chart - Tests system power for ECU
memory keep-alive voltage.
* Ignition Switch "ON" Power Chart - Tests system power
function and fuel pump power function.
* Ignition Switch "ON" Input Chart - Tests closed throttle
(idle) switch, wide open throttle (WOT) switch, manifold
absolute pressure (MAP) sensor, park/neutral switch, coolant
temperature sensor (CTS), manifold air/fuel temperature (MAT\
)
sensor and the respective switch or sensor circuits.
* System Operational Chart - Tests engine start-up and fuel
injector circuits, plus function of closed loop air/fuel
mixture, coolant temperature sensor, manifold air/fuel
temperature sensor, knock sensor and closed loop ignition
retard/advance, EGR valve and canister purge solenoid, idle
speed actuator, and A/C control.
* Basic Engine Chart - Indicates possible failures within other
engine related components.
* Man. Trans. Up-shift Chart - Tests up-shift indicator lamp
function on manual transmission vehicles.

THROTTLE BODY ASSEMBLY
Removal
1) Remove throttle return spring, throttle cable and cruise
control cable, if equipped. Disconnect wiring harness connector from
injector, WOT switch, and ISA motor. Remove fuel supply and return
pipes from throttle body.
2) Identify and tag vacuum hoses for installation later.
Disconnect vacuum hoses from throttle body assembly. Remove throttle
body-to-manifold retaining nuts from studs.
3) Remove throttle body assembly from intake manifold. If
being replaced, transfer ISA motor and WOT switch and bracket
assembly to new throttle body.
Installation
To install, reverse removal procedure using a new gasket
between components. Adjust ISA motor and WOT switch.
FUEL INJECTOR
Removal
Remove air cleaner assembly, injector wire connector, and
injector retainer clip screws. Using a pair of small pliers, gently
grasp center collar of injector (between electrical terminals), and
carefully remove injector with a lifting and twisting motion. Note
back-up ring fits over upper "O" ring.
Installation
1) Lubricate new lower "O" ring with light oil and install
in housing bore. Lubricate new upper "O" ring with light oil and
install in housing bore. Install back-up ring over upper "O" ring.
2) Position new injector in fuel body, and center nozzle in
lower housing bore. Seat injector with a pushing and twisting motion.
Align wire connector terminals properly. Install retainer clip and
screws. Connect injector wire connector.
FUEL PRESSURE REGULATOR
Removal
Remove 3 retaining screws, securing pressure regulator to
fuel body. After noting location of components for reassembly
reference, remove regulator assembly.
Installation
Position pressure regulator assembly with a new gasket.
Install 3 retaining screws, securing regulator to throttle body.
Adjust regulator. Operate engine and inspect for leaks.
IDLE SPEED ACTUATOR, MOTOR & WIDE OPEN THROTTLE SWITCH
NOTE: Closed throttle (idle) switch is integral with ISA and motor
assembly.
Removal
1) Remove air cleaner assembly. Disconnect throttle return
spring, throttle cable and cruise control cable, if equipped.
Disconnect wiring harness connector from ISA motor and WOT switch.
2) Remove ISA motor and WOT switch bracket from throttle
body. Remove motor-to-bracket retaining nuts. See Fig. 23. Do not
remove nuts from motor studs.
CAUTION: Do not attempt to remove ISA motor attaching nuts without

Fig. 28: Jeep 2.5L TBI System Wiring Diagram
FUEL PRESSURE REGULATOR
1) Remove air cleaner assembly. Connect a tachometer to
terminals 1 and 3 of small diagnostic connector D1. Remove screw plug
and install special Fuel Pressure Test Fitting (8983 501 572).

2) Connect accurate fuel pressure gauge to fuel pressure
test fitting. Start engine and accelerate to 2000 RPM. Turn torx head
adjustment screw on bottom of fuel regulator to obtain 17.3 psi (1.2
kg/cm(C)) of fuel pressure.
NOTE: Turning screw inward increases pressure; turning screw
outward decreases it.
3) After specification is reached, install a lead seal ball
to cover regulator adjustment screw. Turn ignition switch off, and
disconnect tachometer. Disconnect fuel pressure gauge, remove test
fitting, and install original plug screw. Install air cleaner
assembly.

\003
4.0 L 6 -C YL - V IN [ M ] & 4 .2 L 6 -C YL - V IN [ C ]

1 988 J e ep C hero ke e
1988 ENGINES
Chrysler Motors 4.0L & 4.2L 6-Cylinder
Jeep; Cherokee, Comanche, Wagoneer, Wrangler
ENGINE CODING
ENGINE IDENTIFICATION
NOTE: For engine repair procedures not covered in this article,
see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article
in the GENERAL INFORMATION section.
The Vehicle Identification Number (VIN) is located on upper
left side of dash and is visible through windshield. The fourth
character identifies the engine size. The tenth character identifies
the model year.
ENGINE IDENTIFICATION CODES TABLE









\









\









\









\









\




Application VIN Code
4.0L 6-Cylinder MPFI ........................ M
4.2L 6-Cylinder 2-Bbl. ...................... C









\









\









\









\









\




SPECIAL ENGINE MARKS
Some engines are produced at factory with oversize or
undersize components. These engines are identified by a letter code
stamped on a boss between ignition coil and distributor. Letters are
decoded as follows:
* "B" indicates all cylinder bores are .010" (.25 mm)
oversize.
* "C" indicates all camshaft bearing bores are .010" (.25 mm)
oversize.
* "M" indicates all main bearing journals are .010" (.25 mm)
undersize.
* "P" indicates all connecting rod journals are .010" (.25 mm)
undersize.
REMOVAL & INSTALLATION
ENGINE REMOVAL
See ENGINE REMOVAL in this section.
INTAKE & EXHAUST MANIFOLD (4.0L)
WARNING: Fuel system is under pressure. Use care when removing fuel
lines to prevent personal injury.
Removal
1) Disconnect negative battery cable. Remove air inlet from
throttle plate assembly. Disconnect throttle, cruise control and
throttle valve (A/T models) cables (if equipped).
2) Disconnect and mark all vacuum and electrical connectors