1988 JEEP CHEROKEE belt

transmission hood release differential warning manual transmission mirror

Page 4 of 1378

JEEP CHEROKEE 1988 Service Repair Manual Removal
1) Remove PCV valve hose at valve cover. Remove valve cover
bolts. Using a razor knife, cut RTV sealant along valve cover. Pry
upward on valve cover in areas marked "PRY HERE

Removal
1) Remove PCV valve hose at valve cover. Remove valve cover
bolts. Using a razor knife, cut RTV sealant along valve cover. Pry
upward on valve cover in areas marked "PRY HERE" near bolt hole areas.
2) Remove valve cover. Alternately loosen each rocker arm
bolt one turn at a time. Remove rocker arm assemblies and push rods.
Mark components for reassembly. Components must be installed in
original location.
Installation
Reverse removal procedures. Install rocker arm components in
original location. Tighten bolts to specification. Apply RTV sealant
on valve cover prior to installation.
VALVE SPRINGS
Valve springs can be removed without removing cylinder head.
Valve Spring Installed Height
Information not available from manufacturer.
HYDRAULIC VALVE LIFTERS
Removal
Remove rocker arms and push rods. See ROCKER ARMS & BRIDGE.
Using Lifter Remover/Installer (J-21884), remove lifter through push
rod openings of cylinder head. Mark lifter location for reassembly
reference. Replace lifters as an assembly if damaged. Internal
components cannot be interchanged.
Inspection
Inspect lifter and camshaft mating surfaces for wear. Check
cylinder block lifter bore diameter. Lifter bore diameter should be
within .9055-.9065" (22.999-23.025 mm). Replace parts as necessary.
Installation
Soak lifter assembly in engine oil supplement prior to
installation. Reverse removal procedures for installation. Install
lifter in original location.
ENGINE FRONT COVER
Removal
1) Disconnect negative battery cable. Remove drive belts, fan
and hub assembly. Remove pulley from vibration damper. Remove
vibration damper retaining bolt and washer.
2) Using Puller (J-21719-01), remove vibration damper and
key. Remove oil pan-to-front cover bolts. Remove cover-to-block
retaining bolts. Remove front cover.
3) Cut oil pan gasket even with face of cylinder block.
Remove gasket from oil pan. Pry crankshaft oil seal from cover.
Installation
1) Ensure all gasket surfaces are clean. Ensure oil slinger
is installed on crankshaft. Apply sealing compound on both sides of
front cover gasket. Install gasket on cylinder block. Replace front
section of oil pan seal with similar section fabricated from new seal.
2) Coat seal with RTV sealant and place in position. Apply
sealant to the joint area of oil pan and cylinder block. Place front
cover on cylinder block. Place Front Cover Seal Installer (J-22248) in\
front cover seal area.
3) Install all retaining bolts. Tighten bolts to

Page 12 of 1378

JEEP CHEROKEE 1988 Service Repair Manual 1) Drain cooling system. Remove fan shroud and drive belts.
Remove fan assembly.
2) Disconnect heater hoses and lower radiator hose at water
pump. Remove water pump retaining bolts.

1) Drain cooling system. Remove fan shroud and drive belts.
Remove fan assembly.
2) Disconnect heater hoses and lower radiator hose at water
pump. Remove water pump retaining bolts. Remove water pump.
Installation
Clean all gasket surfaces. Install water pump. Tighten bolts
to specification. Ensure pump turns freely. Reverse removal
procedures. Fill and purge air from cooling system.
NOTE: It may be necessary to remove heater hose to remove trapped
air if system cannot be purged using following procedures.
Cooling System Air Purge (Vehicles With Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Install
coolant caps. Operate engine to normal operating temperature. Shut off
engine and allow system to cool. Add coolant to recovery bottle.
Repeat procedure to obtain correct coolant level.
Cooling System Air Purge (Vehicles Without Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Operate
engine to normal operating temperature with radiator cap removed. Add
necessary coolant and install radiator cap.
NOTE: For further information on cooling system capacities and
other cooling system components, see ENGINE COOLING SYSTEMS
article.
ENGINE OILING
CRANKCASE CAPACITY
Crankcase capacity is 4 qts. (3.8 L) with oil filter change.
NORMAL OIL PRESSURE
Normal oil pressure should be 13 psi (.91 kg/cm) at 600 RPM
or 37-75 psi (2.6-5.3 kg/cm) at 1600 RPM.
OIL PRESSURE REGULATOR VALVE
Oil pressure regulator valve is located in oil pump body and
is nonadjustable.
OILING SYSTEM
Engine lubrication is provided by the distributor driven
gear-type oil pump. Oil is supplied through the full-flow oil filter
and into an internal oil passage. Internal passage runs along right
side of block and intersects lifter bores.
Oil is then routed to camshaft and crankshaft bearings. Oil
is supplied to rocker arms from the hydraulic lifters and through the
push rods. By-pass valves are located in oil filter mounting and oil
pump.
OIL PUMP
Removal
Remove oil pan. See OIL PAN REMOVAL article. Remove oil pump

Page 56 of 1378

JEEP CHEROKEE 1988 Service Repair Manual from intake manifold. Disconnect fuel lines at fuel rail. Fuel lines
are removed by squeezing the 2 retaining tabs against the fuel line
and pulling the fuel line from the connector. Use caution as th

Page 59 of 1378

JEEP CHEROKEE 1988 Service Repair Manual VALVE SPRING
Valve springs can be removed without removing cylinder head.
Valve Spring Installed
For 4.0L the Valve Spring Installed Height Specification is
1.625

VALVE SPRING
Valve springs can be removed without removing cylinder head.
Valve Spring Installed
For 4.0L the Valve Spring Installed Height Specification is
1.625 inches or 41.29 mm. For the 4.2L the information is not
available from manufacturer.
HYDRAULIC VALVE LIFTER
Removal
Remove cylinder head. See CYLINDER HEAD. Using Lifter
Remover/Installer (J-21884), remove lifter. Mark lifter location for
reassembly reference. Replace lifters as an assembly if damaged.
Internal components cannot be interchanged.
Inspection
Inspect lifter and camshaft mating surfaces for wear. Check
cylinder block lifter bore diameter. Lifter bore diameter should be
within .9055-.9065" (22.999-23.025 mm). Replace parts as necessary.
Installation
Soak lifter assembly in engine oil prior to installation.
Reverse removal procedure for installation. Install lifter in original
location.
ENGINE FRONT COVER
Removal
1) Disconnect negative battery cable. Remove drive belts, fan
and hub assembly. Remove pulley from vibration damper. Remove
vibration damper retaining bolt and washer.
2) Using Puller (J-21719-01), remove vibration damper and
key. Remove alternator and A/C compressor bracket (if equipped).
Remove oil pan-to-front cover bolts. Remove cover-to-block retaining
bolts. Remove front cover.
3) Cut oil pan gasket tabs even with face of cylinder block.
Remove tabs. Remove gasket from oil pan. Pry crankshaft oil seal from
cover.
Installation
1) Ensure all gasket surfaces are clean. Ensure oil slinger
is installed on crankshaft. Apply sealing compound on both sides of
front cover gasket. Install gasket on cylinder block. Replace front
section of oil pan seal with similar section fabricated from new seal.
2) Coat seal with RTV sealant and place in position. Apply
sealant to the joint area of oil pan and cylinder block. Apply engine
oil on seal-to-oil pan contact areas.
3) Place front cover on cylinder block. Place Front Cover
Seal Installer (J-22248) in front cover seal area. Install all
retaining bolts. Tighten bolts to specification.
4) Install front cover oil seal. See FRONT COVER OIL SEAL in
this article. Remove front cover seal installer. Reverse removal
procedure for remaining components. Lubricate vibration damper
retaining bolt with oil prior to installation. Tighten bolts to
specification.
FRONT COVER OIL SEAL
1) Remove vibration damper. Pry seal from front cover. Use

Page 67 of 1378

JEEP CHEROKEE 1988 Service Repair Manual Removal
Drain cooling system. Disconnect radiator and heater hoses
from pump. Remove drive belt(s). Remove fan shroud. Remove fan
assembly. Remove electric cooling fan (if equipped).

Removal
Drain cooling system. Disconnect radiator and heater hoses
from pump. Remove drive belt(s). Remove fan shroud. Remove fan
assembly. Remove electric cooling fan (if equipped). Remove power
steering bracket from water pump. Remove water pump and gasket.
Installation
Ensure gasket surfaces are clean. Install water pump. Tighten
bolts to specification. Ensure pump turns freely. Reverse removal
procedures. Fill and purge air from cooling system.
NOTE: It may be necessary to remove heater hose to remove trapped
air if system cannot be purged using following procedures.
Cooling System Air Purge (Vehicles W/Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Install
coolant caps. Operate engine to normal operating temperature. Shut off
engine and allow system to cool. Add coolant to recovery bottle.
Repeat procedure to obtain correct coolant level.
Cooling System Air Purge (Vehicles W/O Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Operate
engine to normal operating temperature with radiator cap removed. Add
necessary coolant and install radiator cap.
NOTE: For further information on cooling systems, see appropriate
article in the ENGINE COOLING section.
LUBRICATION
CRANKCASE CAPACITY
Crankcase capacity for 4.0L is 5 1/2 qts. (5.2L) or 5 qts.
(4.7L) for 4.2L with oil filter change.
NORMAL OIL PRESSURE
Normal oil pressure should be 37-75 psi (2.6-5.3 kg/cm)
maximum above 1600 RPM. Minimum oil pressure should be 13 psi (.9
kg/cm
) at 600 RPM.
OIL PRESSURE REGULATOR VALVE
Oil pressure regulator valve is located in pump body. Valve
is nonadjustable and serviced as an assembly.
ENGINE OILING SYSTEM
Engine lubrication is provided by the distributor driven
gear-type oil pump. Oil is supplied through the full-flow oil filter
and into an internal oil passage. Internal passage provides oil to the
lifter bores. Oil is then routed to camshaft and crankshaft bearings.
Oil is supplied to rocker arms from the hydraulic lifters and through
the push rods.
OIL PUMP
Removal
Remove oil pan. See OIL PAN REMOVAL in this section. Remove

Page 102 of 1378

JEEP CHEROKEE 1988 Service Repair Manual PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, evacuate system throughly with a
vacuum pump. Charge system

Page 113 of 1378

$JEEP CHEROKEE 1988 Service Repair Manual \ \ \b � � YES \ \ \ NO \b$

\
\
\b
YES \

\
\
NO
\b \b
\
\

\
\

Is Air Flow Correct? Is The Fuse Blown?
\
\
\b \
\
\b
NO YES
\b \b
\

\

Check The Air Replace The Fuse
Distribution \
\b Doors; Ensure

That There Are NO
No Obstructions \b
In The Vent
\
\
\

YES Channels * Apply 12V Directly To

\b \
\b Blower Motor

\
\
\
* Does The Blower Motor Turn?
* Test Drive Belt Tension
\
\
\
\b * Is The Clutch Defective?

\
\
\b NO
\b YES
\
\

\b Replace Blower Motor

\
\
\
\b * Apply 12V

Directly To YES
Clutch
\b * Is Clutch
\
\

Defective? Is The Switch Defective?

\
\b \
\
\b

YES YES

\b \b
\

\

Replace Clutch Replace Switch

\
\b \
\b

NO NO
\b \b
\

\
\

Repair Wiring Repair The Wiring Harness
NO Harness \
\
\b \b \
\b
\
\

Low R-12 Refrigerant?
\
\
\b \

NO \

\
\
YES Charge System
\b \b \
\b
\
\
\

Is The Pressure Switch Defective?
\
\
\
\b
YES \

\
\
NO
\b \b
\
\

\
\

Replace Pressure Switch Replace Expansion Valve
\
\
\b \
\
\b
CONDITION & POSSIBLE CAUSE

Page 114 of 1378

$JEEP CHEROKEE 1988 Service Repair Manual \ \ \ \ \ \ \ Compressor Runs Rough * Incorrect oil or re$

Load next 8 pages

Page: 1-8 9-16 17-24 25-32 33-40 ... 104 next >

battery replacement radio heater reset roof rack lug pattern