1987 MAZDA 626 oil level

0 PRE-DELIVERY INSPECTION
PRE-DELIVERY INSPECTION TABLE
EXTERIOR
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Glass, exterior bright metal and paint for damage
• Wheel lug nuts
88—118 N m (9—12 m-kg, 65—87 ft-lb)
• Tire pressures (Refer to section 12)
• All weatherstrips for damage or detachment
• Operation of bonnet release and lock
• Operation of fuel lid and trunk lid (Back door) opener
• Door operation and alignment
• Headlight aiming
INSTALL following parts:
• Wheel caps or rings (if equipped)
• Outside rear view mirror(s)
UNDER BONNET—ENGINE OFF
INSPECT and ADJUST, if necessary, the following items
to the specifications:
• Fuel, coolant and hydraulic lines, fittings, connections and
components for leaks
• Engine oil level
• Power steering fluid level (if equipped)
• Brake and clutch master cylinder fluid level (if equipped)
• Windshield washer reservoir fluid level
• Radiator coolant level and specific gravity
Protection °C (°F) Specific gravity at 20°C (68°F)
-4 (25) 1.028
-16(3) 1.054
-26 (-15) 1.066 -40 (-40) 1.078
• Tightness of water hose clamps (including heater hoses)
• Tightness of battery terminals
• Manual transaxle oil level
• Drive belt tensions (Refer to section 1)
• Accelerator cable and its linkage for free movement
• Headlight cleaner fluid level (if equipped)
CLEAN spark plugs
INTERIOR
INSTALL the following parts:
• Rubber stopper for inside rear view mirror
• Fuse for accessories
CHECK the operations of the following items:
• Seat controls (sliding and reclining) and head rest
• Door locks including childproof door locks (if equipped)
• Seat belts and warning system
• Ignition switch and steering lock
• Inhibitor switch (ATX only)
• All lights including warning and indicator lights
• Sound warning system
• Headlight cleaner (if equipped)
• Horn, wipers and washers (front and rear, if equipped)
• Radio and antenna (if equipped)
• Cigarette lighter and clock
• Remote control outside rear view mirrors (if equipped)
• Power windows (if equipped)
• Heater, defroster and air conditioner at various mode
selection (if equipped)
• Sunroof (if equipped)
ADJUST antenna trimmer on radio (if equipped)
CHECK the following items:
• Presence of spare fuse
• Upholstery and interior finish
CHECK and ADJUST, if necessary, the following items:
• Operation and fit of windows
• Pedal height and free play of brake and clutch pedal
Pedal height mm (in) free play mm (in)
Clutch pedal 216.5-221.5 (8.52-8.72) 5-13 (0.2-0.51)
Brake pedal 222-227 (8.74-8.94) 4-7 (0.16-0.28)
• Parking brake
5-7 noches/98 N (10 kg, 22lb)
UNDER BONNET—ENGINE RUNNING AT
OPERATING TEMPERATURE
CHECK the following items:
• Operation of idle-up system for air conditioner or power
steering (if equipped)
• Automatic transaxle fluid level
• Operation of dash pot
• Initial ignition timing
• Idle speed
ON HOIST
CHECK the following items:
• Underside fuel, coolant and hydraulic lines, fittings, con-
nections and components for leaks
• Tires for cuts or bruises
• Steering linkage, suspension, exhaust system and all un-
derside hardware for looseness or damage
REMOVE protective cover from brake discs
ROAD TEST"
CHECK the following items:
• Brake operation
• Clutch operation
• Steering control
• Operation of meters and gauge
• Squeaks, rattles or unusual noise
• Engine general performance (including turbo)
• Emergency locking retractors
• Cruise control system (if equipped)
AFTER ROAD TEST
REMOVE seat and floor mat protective covers
CHECK for necessary owner information materials, tools and
spare tire in vehicle
-76G00X-002
0-2

U1
Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x 1000 Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x
1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Battery electrolyte level and specific gravity A A A A O o O O • Electroyte level • Specific gravity 5-8
Drive belts A A A A A O 0 o O • Cracks or damage • Tension

1
A—7
1B—6
1C-7
Engine timing belts Replace every 100,000 Km o o o o — 1A—14 1B—11 1C—11
Engine valve clearance A A A A A o X X o
• Valve clearance: F8 (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE-12-valve, FE (DOHC) IN: 0; Maintenance free EX: 0; Maintenance free RF-CX, RF-N (Cold engine) IN: 0.25 mm (0.010 in) EX: 0.35 mm (0.014 in)
1A-10
1C—85
Intake and exhaust manifold nuts and
bolts T T T o o X X
• Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb)

1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X IN EX
1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X F8, FE 19-30 (1.9-3.1,
14-22)
22-28 (22—2.9, 16-21)

1
A—86 1B—68 1C—89
Intake and exhaust manifold nuts and
bolts T T T o o X X
RF-CX RF-N 16-23 (1.6-2,3,
12-17)
22-26 (2.2-2.7,
16-20)

1
A—86 1B—68 1C—89
Engine oil *2 R R R R R R R R R o o 0 o
• Oil pan capacity F8, FE: 3.6 liters (3.8 US qt, 3.2 Imp qt) RF-CX, RF-N:
5.0 liters (5.3 US qt, 4.4 Imp qt)
2A—6
2B-6
Oil filter *2 R R R R R R R R o o o o
• Oil filter capacity F8, FE 12-valve
0.3 liters (0.32 US qt, 0.26 Imp qt) FE (DOHC)
0.2 liters (0.21 US qt, 0.18 Imp qt) RF-CX, RF-N
0.4 liters (0.42 US qt, 0.35 Imp qt)
2A—6
2B-6
Fuel filter (R) for carbretor model (R) R (R) R o 0 o o — 4A—37

Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
x 1000 Km 1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item Miles x 1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Idle-up solenoid valve I I I I O MTX o X X — 4A—56
All electrical system *4 I I I I I I I I o o o o • Check the all electrical system Section 15
Head light aligment A A A A o o o o • Check the head light aiming 14-31
Steering and front suspension I I I I o o o 0 • Damage 10—28
Front and rear power steering system
and hoses (For 4WS) I I X X o X • Operation and looseness • Fluid leakage or oozing 10—44 10—14
4-Wheel steering system operation
and linkage (For 4WS) I I X X o X • Operation and looseness
• Fluid leakage or oozing
10—33 10—14
Rear wheel steering steering angle
(For 4WS) I I X X o X • Steering wheel angle: Inner 5°00' ± 45' Outer 5°00' ± 45'
13-54
Solenoid valve oil filter (For 4WS) R R X X o X — 10-41
Rear suspension outer ball joints
(For 4WS) I I X X o X • Damage, looseness and grease
leakage 13—37
Manual transaxle oil A R o o o 0 • Oil capacity 3.35 liters (3.6 US qt, 3.0 Imp qt) 7A-6
Automatic transaxle fluid level A A o o X X • Oil capacity 4-Speed 6.8 liters (7.2 US qt, 6.0 Imp qt) 3-Speed 6.2 liters (6.6 US qt, 5.5 Imp qt)
7B-2
Bolts and nuts on chasis and body T T T T T o o o o — —
Disk brakes/Drum brakes I I I I o o o o
• Min. pad thickness: Front 2.0 mm (0.08 in) Rear 1.0 mm (0.04 in) • Min. disc thickness: Front 14 or 15 inch-wheel
22 mm (0.87 in) 13 inch-wheel 18 mm (0.71 in) Rear 8.0 mm (0.31 in)
• Disc run out:
Front 0.1 mm (0.004 in) Rear 0.1 mm (0.004 in)
• Min. lining thickness: 1.0 mm (0.04 in) • Max, drum inner dia: 230.1 mm (9.06 in)
11—45
11—54
11—45
11—54
11-45 11—54
11-60
11—60

Interval
Procedure & item
Number of Months or km, whichever corns first
Months

x
1000
Km
Miles x 1000
0.6
6
10
12
20
12
18
30
18
24
40
24
30
50
30
36
60
36
42
70
42
48
80
48
®3 ©4 Service data and inspection point Page
m z >
z o m
H >
00 I-m
m o m
c 3 a to Qt (0 O
A
Battery electrolyte level and specific gravity O o o o Electroyte level Specific gravity 5-8
Drive belts O O o o Cracks or damage Tension

1
A—7
1B-6
1C-7
Engine timing belts Replace Severy 100,000 Km O O o o
Engine valve clearance
Intake and exhaust manifold nuts and bolts
O
O
o o
Valve clearance: FE-8-valve (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE (DOHC)
IN: 0; Maintenance free EX: 0; Maintenance free RF-CX, RF-N (Cold engine) IN: 0.25 mm (0.010 in) EX: 0.35 mm (0.014 in)
O IN EX
FE FE DOHC 19-30(1.9-3.1,
14-22)
22-28 (2.2-2.9
16-21)
1A—14 1B—11 1C-11

1
A—10
1C-85
Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb)
1A—86
1B—68 CO 0 1 m o
m a
H m
o m
Engine oil O
Oil filter O
O o o
Oil pan capacity FE: 3.6 liters
(3.8 US qt, 3.17 Imp qt) RF-CX, RF-N: 5.0 liters (5.3 US qt, 4.4 Imp qt)
O o o
Oil filter capacity FE 8-valve
0.3 liters (0.32 US qt, 0.26 Imp qt) FE (DOHC)
0.2 liters (0.21 US qt, 0.18 Imp qt) RF-CX, RF-N
0.4 liters (0.42 US qt, 0.35 Imp qt)
2A-6
2B-6
2A-6
2B-6

GO
Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
x 1000 Km 1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item Miles x 1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Dashpot (only for MTX) I I I I X X o X • Operation 4A—50
Coast enrichment solenoid valve I I I I X X o X — 4A—54
All electrical system *4 I I I I I I I I o o o o • Check the all electrical system Section 15
Head light aligment A A A A o o o o • Check the head light aiming 14-31
Steering and front suspension I I I I o o o o 10—28
Front and rear power steering system
and hoses (For 4WS) I I X o X X • Operation and looseness
• Fluid leakage or oozing 10—44
10-14
4-Wheel steering system operation
and linkage (For 4WS) I I X o X X • Operation and looseness
• Fluid leakage or oozing
10—33 10—14
Rear wheel steering angle (For 4WS) I I X o X X • Steering wheel angle: Inner 5°00' ± 45' Outer 5°00' ± 45'
13-54
Solenoid valve oil filter (For 4WS) R R X o X X — 10—41
Rear suspension outer ball joints
(For 4WS) I I X o X X • Damage, looseness and grease
leakage 13-37
Manual transaxle oil A R o o o o • Oil capacity 3.35 liters (3.6 US qt, 3.0 Imp qt) 7A—6
Automatic transaxle fluid level A A o o o X
• Oil capacity 4-Speed and EC-AT 6.8 liters (7.2 US qt, 6.0 Imp qt) 3-Speed 6.2 liter (6.6 US qt, 5.5 Imp qt)
7B—71
7C—25
Bolts and nuts on chasis and body T T T T T o o o o — —
Brake lines, Hoses, and connections I I I l_
I
o o o o • Proper attachment and connections 11-8
Disk brake/Drum brake I I I
l_
I o o o 0
• Min. pad thickness: Front 2.0 mm (0.08 in) Rear 1.0 mm (0.04 in)
• Min. disc thickness: Front 14 or 15 inch-wheel 22 mm (0.87 in)
13 inch-wheel 18 mm (0.71 in) Rear 8.0 mm (0.31 in)
• Disc run out:
Front 0.1 mm (0.004 in) Rear 0.1 mm (0.004 in) • Min. lining thickness: 1.0 mm (0.04 in)
• Max. drum inner dia: 230.1 mm (9.06 in)
11—45 11—54
11—45
11-54
11—45
11-54
11—60
11-60

Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x
1000
Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x
1000 0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Choke system I I I I O O X X
• Carburetor linkage • Choke diaphragm • Choke valve clearance • Unloader system
4A—26
4A-34
4A-34
4A—33
Cooling system I I I I O O o o • Hoses for cracks or wear 3A-5 3B—4
Engine coolant (with reservoir) Reprace every 24 months O O o o • Coolant level 3 A—5 3B—4
Battery electrolyte level and specific gravity I I I I O o o o • Electrolyte level • Specific gravity 5—8
Engine timing belts *2 Replace every 100,000 km O o o o —
1A—14 1B—11 1C—11
Drive belts *4 A I I I I I I I I O o o o • Cracks or damage • Tension
1A—7
1
B—6 1C—7
Engine valve clearance
(1) For Gasoline engine (I) I (I) I (I) I (I) I
T
O o X o
• Valve clearance F6, F8, FE-8-valve (Hot engine) IN: 0.30 mm (0.012 in) EX: 0.30 mm (0.012 in) FE-12-valve, FE (DOHC) IN: 0; Maintenance free EX: 0; Maintenance free RF-N (Cold engine) IN: 0.25 mm (0.01 in) EX: 0.35 mm (0.014 in)
1A—10
1C—85
Exhaust manifold nuts and bolts T T
I
T o o X X
• Retighten the intake and exhaust manifold nuts
N-m (m-kg, ft-lb) 1A—86 1B—68 1C—89 Exhaust manifold nuts and bolts T T
I
T o o X X IN EX 1A—86 1B—68 1C—89 Exhaust manifold nuts and bolts T T
I
T o o X X
F6, F8, FE 19-30 (1.9-3.1, 14-22) 22-28 (2.2-2.9, 16-21)
1A—86 1B—68 1C—89 Exhaust manifold nuts and bolts T T
I
T o o X X
RF-N 16-23 (1.6-2.3,
12-17) 22-26 (2.2-2 7,
16-20)
1A—86 1B—68 1C—89
Engine oil *1 Replace every 5000 km or 6 months X X o o
• Oil pan capacity FE DOHC: 3.6 liters
(3.8 US qt, 3.2 Imp qt) RF-N: 5.0 liters
(5.3 US pt, 4.4 Imp qt)
2A-6
2B—6
m >
o m
H >
00 r~ m
a 2

CD
o> O o o X o
Interval
Procedure & item
Number of Months or km, whichever corns first
©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Months — 6 12 18 24 30 36 42 48 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item

x 1000 Km
1 10 20 30 40 50 60 70 80 ©1 ©2 ©3 ©4 Service data and inspection point Page
Interval
Procedure & item
Miles x 1000
0.6 6 12 18 24 30 36 42 48
©1 ©2 ©3 ©4 Service data and inspection point Page
Idle mixture (1) only for carbretor (I) I I I I O O o X
• CO concentration 2.0 ± 0.5 % CO concentration FE DOHC 1.5 ± 0.5 % HC concentration FE DOHC Less than 1000 rpm
4A-38
4C-30
Evaporative system
(only for middle east) I I I I X O X X — 4A—78
Dashpot (only for MTX) I I I I o X X X • Operation 4A—50
Coasting leaner system *6 t I I I
,
O X X X — 4A-56
Brake lines, hoses and connections I I I I o o o o • Proper attachment and connections 11-8
Disc brakes [ I I I I [ I I o o o o
• Min. pad thickness: Front 2.0 mm (0.08 in) Rear 1.0 mm (0.04 in)
• Min. disc thickness: Front 14 or 15 inch-wheel 22 mm (0.87 in)
13 inch-whel 18 mm (0.71 in) Rear 8.0 mm (0.31 in) • Disc run out: Front 0.1 mm (0.004 in) Rear 0.1 mm (0.004 in)
11—45 11—54
11—45
11—54
11—45
11—54
Drum brakes I I I I o o X o
• Min. lining thickness: 1.0 mm (0.004 in)
• Max. drum inner dia: 14 or 15 inch-wheel 230.1 mm (9.06 in) 13 inch-wheel 201.5 mm (7.93 in)
11-60
11—60
Steering linkages, rack guide and tie
rod ends I I I I I o o o o • Operation and looseness 10-11
Manual transaxle oil R o o 0 o • Oil capacity
3.35 liters (3.6 US qt, 3.0 Imp qt) 7A—6
Automatic transaxle fluid level I I I I o o X X
• Oil capacity 4-Speed 6.8 liters (7.2 US qt, 6.0 Imp qt) 3-Speed 6.2 liters (6.6 US qt, 5.5 Imp qt)
7B—71
7C-25
m z >
o m
H >
CO I-m
"ti o
a 0)

1A TUNE-UP PROCEDURE
76G01A-102
76G01A-103
76G01A-104
TUNE-UP PROCEDURE
Tune the engine according to the procedures
described below.
Battery
1. Check for corrosion on the terminals, or loose ca-
ble connections.
If necessary, clean the clamps and tighten firmly.
2. Check that the electrolyte level is between the UP-
PER and LOWER marks.
Add distilled water if necessary.
3. Check the specific gravity by using a hydrometer.
If the specific gravity reading is 1.200 or less,
recharge the battery. (Refer to Section 5.)
Air Cleaner Element
Visually check the air cleaner element for excessive
dirt, damage, or oil. Replace if necessary.
Caution
Do not clean the air cleaner element with com-
pressed air, replace if necessary.
Engine Oil
Check the engine oil level and condition with the oil
level gauge.
Add oil, or change it, if necessary.

76G01A-019

1A—6