1987 MAZDA 626 oil level

1 C ON-VEHICLE MAINTENANCE (CYLINDER HEAD)
CYLINDER HEAD
Removal
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G01C-031
1. Accelerator cable
2. Air cleaner
3. Brake vacuum pipe
4. Intercooler pipe and hose*
5. Drive belt cover
6. Vacuum pump drive belt
7. Fuel hose
8. Water temperature switch
connector
9. Glow plug connector
10. Water thermo switch con-
nector
11. Heat gauge unit connector
12. Boost air temperature sen-
sor connector*
13. Injection pipes
14. Upper radiator hose
15. Water hose
(thermostat—FIR)
16. Oil level gauge and stay
bolt
17. Oil pipe bolt
18. Timing belt (Refer to page
1C—11)
19. Cylinder head cover
20. Camshaft pulley
21. Rear camshaft pulley
76G01C-032
22. Injection pump pulley
23. Seal plate
24. Water hose and pipe
25. Comprex supercharger
drive belt*
26. Heat insulator*
27. Exhaust manifold stay
28. Front exhaust pipe
29. Cylinder head bolt
30. Cylinder head
31. Cylinder head gasket
32. Comprex supercharger*
33. Exhaust manifold
34. Intake manifold
Note
* marked parts are equipped only for the RF-CX.
1C-16

DISASSEMBLY (INJECTION PUMP) 1 C
INJECTION PUMP
76G01C-082
1. No.3 engine mount and idler
2. Injection pipe
3. Injection pump
4. Oil level gauge and stay
5. Oil pipe
6. Fuel feed pipe
7. Oil pressure switch
8. Water pipe
9. Water pump
Disassembly Note
Injection pump
Remove the injection pump with its brackets.
If separate them, adjust the injection timing after in-
stalling the timing belt referring to Section 4D.
76G01C-083
1C-39

ASSEMBLY (INJECTION PUMP) 1 C
Water Pipe
1. Apply a coat of vegetable oil to the O-ring.
2. Install the water pipe.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
3. Connect the water hose.
76G01C-181
^OQOja^q^
cffl-.. M
Oil Pressure Switch
Install the oil pressure switch.
Tightening torque: 12—18 N-m
(1.2—1.8 m-kg, 104—156 in-lb)
76G01C-182
Fuel Feed Pipe and Oil Pipe
1. Install the fuel feed pipe and tighten bolt (A).
Tightening torque:
19—26 N-m (1.9—2.6 m-kg, 14—19 ft-lb)
2. Install the oil pipe and loosely tighten the bolts (B).
76G01C-183
"m
fa?-^ lA-f! . 11
? - ' ~" ~ -'
Oil Level Gauge
Install the oil level gauge and stay.
Tightening torque:
8—12 N-m (80—120 cm-kg, 69—104 in-lb)
76G01C-184
1C-79

INSTALLATION 1C
Accelerator Cable
Install the accelerator cable.
76G01C-235
76G01C-236
Engine Oil
Add the specified amount and type of engine oil. (Re-
fer to Section 2B)
Coolant
Close the drain plug, fill the radiator and reservoir tank
with the specified amount and type of coolant. (Re-
fer to Section 3B)
Check Engine Condition
1. Check for leaks.
2. Perform engine adjustments if necessary.
3. Perform a road test.
4. Recheck the oil and coolant levels.
1C—99

INSPECTION, ENGINE OIL 2A
86U02X-004
INSPECTION
ENGINE OIL
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temper-
ature and stop it.
3. Wait for five minutes.
4. Remove the oil level gauge and check the oil lev-
el and condition.
5. Add or replace oil if necessary.
Note
The distance between the L and F marks on
the level gauge represents 1.0 liter (1.06 US
qt, 0.88 Imp qt).
OIL PRESSURE
1. Remove the oil pressure switch.
69G02A-006
76G02A-005
86U02X-006
2. Screw the SST into the pressure switch installa-
tion hole.
3. Warm up the engine to normal operating tem-
perature.
4. Run the engine at 3,000 rpm, and note the gauge
reading.
Oil pressure:
343—441 kPa
(3.5—4.5 kg/cm2, 50—64 psi)...DOHC 2g4 392 kPa
(3.0—4.0 kg/cm2, 43—57 psi)...SOHC
5. If the pressure is not as specified, check for the
cause, and repair if necessary.
(Refer to Troubleshooting Guide.)
ENGINE OIL
REPLACEMENT
1. Warm up the engine to the normal operating tem-
perature and stop it.
2. Remove the oil filler cap and the oil pan drain plug.
3. Drain the oil into a suitable container.
Warning
Be careful when draining, the oil is very hot.
2A-5

2A OIL FILTER, OIL COOLER
j
F

k
4

4. Install the drain plug and a new gasket.
5. Refill the engine with the specified type and amount
of oil.
6. Refit the oil filler cap.
Oil pan capacity:
3.6 liters (3.8 US qt, 3.2 Imp qt)
7. Recheck the oil level after the engine has been run.
76G02A-006
TbJ
r
86U02X-008
76G02A-007
0
A
if \ lO
/O
f \ 11 • V jJ
VJ f .fa,-
n D
©
76G02A-008
OIL FILTER
REPLACEMENT
1. Remove the oil filter with a suitable wrench.
2. Use a clean rag to wipe off the mounting surface
on the engine.
3. Apply a small amount of engine oil to the rubber
seal of the new filter.
Warning
Be careful that the engine and filter are very
hot.
4. (DOHC)
Install the oil filter until the rubber seal contacts the
base and then tighten the filter
1
and
1
/6 turn with
a wrench.
(SOHC)
Install the oil filter and tighten it by hand only. Do
not use a wrench.
5. Start the engine and inspect around the filter seal
for leaks.
6. Check the oil level and add oil if necessary.
Oil filter capacity:
0.20 liters (0.21 US qt, 0.18 Imp qt)...DOHC
0.30 liters (0.32 US qt, 0.26 Imp qt)...SOHC

OIL
COOLER

(DOHC, 12-valve,
ECE
8-valve)

REMOVAL AND INSTALLATION
Remove in the sequence shown in the figure.
Install in the reverse order of removal.
1. Water hose
2. Oil filter
3. Nut
4. Oil cooler
Nut tightening torque:
29—39
N
m (3.0—4.0 m-kg, 22—29 ft-lb)
2A-6

INSPECTION 2B
A
76G02B-006
INSPECTION
ENGINE OIL
1. Be sure the vehicle is on level ground.
2. Warm up the engine to normal operating temper-
ature and stop it.
3. Wait for five minutes.
4. Remove the oil level gauge and check the oil lev-
el and condition.
5. Add or replace oil if necessary.
Note
The distance between the L and F marks on
the level gauge represents 1.2 liters (1.26 US
qt, 1.05 Imp qt).
OIL PRESSURE
1. Disconnect the oil hose (vacuum pump—cylinder
block).
76G02B-007
2. Set the SST as shown.
3. Remove the vacuum pump drive belt to prevent
heat damage to bearing.
4. Warm up the engine to normal operating tem-
perature.
76G02B-008
5. Run the engine first at 1,000 rpm, then at 3,000
rpm and note the gauge reading.
Standard oil pressure kPa (kg/cm2, psi)

1,000 rpm 147-245 (1.5-2.5, 21-36)
3,000
rpm
343—441 (3.5-4.5, 50—64)

6. If the pressure is not as specified, check for the
cause, and repair if necessary.
(Refer to Troubleshooting Guide.)
76G02B-009
2B—5

2B
ENGINE OIL, OIL
FILTER
86U02X-006
76G02B-010
86U02X-008
ENGINE OIL
REPLACEMENT
1. Warm up the engine to the normal operating tem-
perature and stop it.
2. Remove the oil filler cap and the oil pan drain plug.
3. Drain the oil into a suitable container.
Warning
Be careful when draining, the oil is very hot.
4. Install the drain plug and a new gasket.
Tightening torque:
29—41 N-m (3.0—4.2 m-kg, 22—30 ft-lb)
5. Refill the engine with the specified type and amount
of oil.
6. Refit the oil filler cap.
Oil pan capacity:
5.0 liters (5.3 US qt, 4.4 Imp qt)
7. Recheck the oil level after the engine has been run.

OIL
FILTER
REPLACEMENT
1. Remove the oil filter with a suitable wrench.
2. Use a clean rag to wipe off the mounting surface
on the engine.
3. Apply a coat of engine oil to the filter rubber seal.
4. Install the oil filter until the rubber seal contacts the
oil cooler by hand. Then tighten it a 7/6 turn fur-
ther with a band type wrench.
5. Start the engine and inspect around the filter seal
for leaks.
6. Check the oil level and add oil if necessary.
Oil filter capacity:
0.50 liters (0.52 US qt, 0.44 Imp qt)
76G02B-011
2B—6