1987 MAZDA 626 relay

4B CONTROL SYSTEM
Terminal Input Output Connection to Voltage (After warming-up) Remarks Terminal Input Output Connection to IGN: ON Idle Remarks
2N o Solenoid valve (EGR) Below 1,5V • Cold engine: be-low 1,5V Radiator coolant temp.—below 17°C (63°F) or Engine coolant temp.—below 70°C (158°F)
• Engine above ap-prox. 1,500 rpm: Battery voltage
20 o Air bypass solenoid valve (Idle-up B) Battery voltage While solenoid ON (Refer to page 4B-35): below 1.5 V
2P o Solenoid valve
(Purge control valve)
Battery voltage • Medium and high
load: below 1,5V
2Q — — — —
2R — — Ground (E02) Below 1,5V
3A — — Ground (E01) Below 1.5V
3B O Ignition switch (Start position) Below 1,5V While cranking: bat-
tery voltage
3C o Injector (No. 4 and No. 2) Battery voltage *1 Battery voltage *1 Engine Signal Monitor green and red lights flash
3D o Inhibitor switch "N" or "P" range: below 2.0V
Other ranges: battery voltage
ATX
3E o Injector (No. 1 and No. 3) Battery voltage *
1
Battery voltage *1 Engine Signal Monitor: green and red lights flash
3F -— — — —
3G — Ground (Ei) Below 1.5V
3H — — — —
31 o — Ma ri relay Battery voltage
3J — — Battery Battery voltage For back-up
76G04B-110
31 3G 3E 3C 3A
3J 3H 3F 3D 3B
2Q 20 2M 2K 21 2G 2E 2C 2A
2R 2P 2N 2L 2J 2H 2F 2D 2B
1W 1U 1S 1Q 10 1M 1K 11 1G 1E 1C 1A
1X 1V 1T 1R 1P 1N 1L 1J 1H 1F 1D 1B
4B—90

4B CONTROL SYSTEM
E/L CONTROL UNIT
Inspection
1. Connect a voltmeter between the E/L control unit
and ground.
2. Start the engine and check the terminal voltages
as described below.
69G04A-174
Terminal Input Output Connection to Voltage (after warm-up) Remarks Terminal Input Output Connection to Ignition switch: ON idle Remarks
A
(BW) — — Ignition switch Battery voltage
B — — — — — —
C
(B) — — Ground OV
D (LY) 0 Electrical fan relay
Battery voltage Coolant temp.: below 97°C (207°F) D (LY) 0 Electrical fan relay
Below 1,5V Coolant temp.:
above 97°C (207°F)
E
(GY) o Engine control unit
(11)
OV E/L: ON E
(GY) o Engine control unit
(11) Battery voltage E/L: OFF
F (RB) 0 Headlight switch
Battery voltage Headlight switch:
ON F (RB) 0 Headlight switch
Below 1,5V Headlight switch:
OFF
G (LB) 0 Blower motor switch
Below 1,5V Blower motor switch: ON (3rd or 4th position) G (LB) 0 Blower motor switch
Approx. 5V Others
H
(BL) 0 Rear defroster switch
Below 1,5V Rear defroster switch: ON H
(BL) 0 Rear defroster switch Battery voltage Rear defroster switch: OFF
76G04B-131
Replacement
1. Remove the engine control unit. (Refer to page
4B-91)
2. Replace the E/L control unit.
3. Install in the reverse order of removal.
4B—93

4C
FUEL AND EMISSION
CONTROL SYSTEMS
(FUEL INJECTION FE DOHC)
OUTLINE 4C— 2
COMPONENT APPLICATION 4C— 2
SYSTEM DIAGRAM 4C— 3
COMPONENT LOCATION 4C— 4
VACUUM HOSE ROUTING
DIAGRAM 4C— 7
SPECIFICATIONS 4C— 8
TROUBLESHOOTING GUIDE 4C— 9
TROUBLESHOOTING WITH SST.. 4C— 11
INSPECTION PROCEDURE 4C— 12
PRINCIPLE OF CODE CYCLE 4C— 13
CODE NUMBER 4C— 14
SWITCH MONITOR FUNCTION 4C— 25
INSPECTION PROCEDURE 4C— 26
IDLE ADJUSTMENT 4C— 29
IDLE SPEED 4C— 29
IDLE MIXTURE 4C— 30
INTAKE AIR SYSTEM 4C— 31
COMPONENT DESCRIPTION 4C— 31
REMOVAL 4C— 32
PARTS INSPECTION 4C— 33
REPLACEMENT 4C— 36
INSTALLATION 4C— 37
VARIABLE INERTIA CONTROL
(VIC) SYSTEM 4C— 39
COMPONENT DESCRIPTION 4C— 40
TROUBLESHOOTING 4C— 40
IDLE SPEED CONTROL
(ISC) SYSTEM 4C— 44
COMPONENT DESCRIPTION 4C— 45
TROUBLESHOOTING 4C— 46
REMOVAL 4C— 48
FUEL SYSTEM 4C— 49
COMPONENT DESCRIPTION 4C— 50
TROUBLESHOOTING 4C— 51
FUEL PRESSURE RELEASE AND
SERVICING FUEL SYSTEM 4C— 52
MULTI-PRESSURE TESTER 4C— 53
FUEL PUMP 4C— 56
PULSATION DAMPER 4C— 57
INJECTOR 4C— 57
TRANSFER PUMP CONTROL
SYSTEM 4C— 59
REPLACEMENT 4C— 60
FUEL TANK 4C— 65
PRESSURE REGULATOR
CONTROL (PRC) SYSTEM 4C— 68
COMPONENT DESCRIPTION 4C— 69
TROUBLESHOOTING 4C— 69
DECELERATION CONTROL
SYSTEM 4C— 72
COMPONENT DESCRIPTION 4C— 73
TROUBLESHOOTING 4C— 73
ELECTRONIC SPARK ADVANCE
(ESA) CONTROL SYSTEM 4C— 75
COMPONENT DESCRIPTION 4C— 76
TROUBLESHOOTING 4C— 76
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4C- 77
COMPONENT DESCRIPTION 4C— 77
TROUBLESHOOTING 4C— 78
EVAPORATIVE EMISSION
CONTROL (EEC) SYSTEM 4C— 80
COMPONENT DESCRIPTION 4C— 80
TROUBLESHOOTING 4C— 81
POSITIVE CRANKCASE
VENTILATION (PCV) SYSTEM.... 4C— 86
COMPONENT DESCRIPTION 4C— 86
PCV VALVE 4C— 86
EXHAUST SYSTEM
(UNLEADED FUEL) 4C— 87
REMOVAL AND INSTALLATION.. 4C— 88
INSPECTION 4C— 88
EXHAUST SYSTEM
(LEADED FUEL) 4C— 89
REMOVAL AND INSTALLATION.. 4C— 90
CONTROL SYSTEM 4C— 91
RELATIONSHIP CHART 4C— 92
EGI MAIN FUSE 4C— 96
CONTROL RELAY 4C— 96
NEUTRAL SWITCH 4C— 97
CLUTCH SWITCH 4C— 97
P/S PRESSURE SWITCH 4C— 97
ENGINE CONTROL UNIT 4C— 98
E/L CONTROL UNIT 4C—102
AIR FLOW SENSOR 4C—103
THROTTLE SENSOR 4C—104
IDLE SWITCH 4C—106
WATER THERMO SWITCH 4C—106
WATER THERMO SENSOR 4C—107
OXYGEN SENSOR 4C—107
DISTRIBUTOR 4C—108
OXYGEN SENSOR HEATER 4C—109
KNOCK SENSOR 4C—109
INTAKE AIR THERMO SENSOR .. 4C—110
76G04C-001

4C OUTLINE
COMPONENT LOCATION
Input and Output Devices
Solenoid Solenoid Idle valve valve switch /nnA
Solenoid
valve*1 Solenoid valve*1
'(No.1 purge control)
E/L control unit
Engine control unit
Control relay
Knock sensor*2
Water thermo
switch*1
Oxygen Distributor
sensor*1
Clutch switch
\ Oxygen sensor
\ relay*1
Solenoid valve*1 (EGR)
Solenoid valve (ISC)
Air flow sensor
Neutral switch
Water thermo sensor
*1...Unleade fuel only
*2...Leaded fuel only
76G04C-004
4C—4

4C TROUBLESHOOTING WITH SST
Check connector: (Green, 6 pin)
49 H018 9A1
86U04A-011
Test connector: (Green, 1 pin)'
INSPECTION PROCEDURE
1. Connect the SST to the check connector. (Green,
6-pin) and the negative battery terminal.
2. Set the select switch to position A.
Note
The check connector is located at the rear of
the left side wheel housing.
3. Ground the test connector (Green, 1-pin) with a
jumper wire.
Note
The test connector is located near the Self-
Diagnosis Checker check connector.
86U04A-012
OO
uu
SELF-DIAGNOSIS CHECKER
MONITOR LAMP SELECT SW «

o o o
o
76G04C-012
4. Turn the ignition switch ON.
5. Verify that 88 flashes on the digital display and that
the buzzer sounds for three seconds after turn-
ing the ignition switch ON.
6. If 88 does not flash, check the control relay (refer
to page 4C—96), power supply circuit, and check
connector wiring.
7. If 88 flashes and the buzzer sounds continuously
for more than 20 seconds check the check con-
nector wiring, then replace the engine control unit
and perform steps 3 and 4 again.
8. Note the code numbers and check for the causes
by referring to the check sequences shown on
pages 4C—16 to 4C—24. Repair as necessary.
Note
Cancel the code numbers by performing the
after-repair procedure after repairing.
AFTER-REPAIR PROCEDURE
1. Cancel the memory of malfunctions by disconnect-
ing the negative battery cable and depress the
brake pedal for at least five seconds.
76G04C-013
4C-12

TROUBLESHOOTING WITH SST 4C
Malfunction display
Sensor or subsystem Self-diagnosis Fail-safe Malfunction
code no. Malfunction code output signal pattern
Sensor or subsystem Self-diagnosis Fail-safe
08
Air flow sensor Open or short circuit Maintains basic sig-nal at preset value
09 o°pNp II IIL •
Water thermo sensor Open or short circuit Maintains constant 35°C (95°F) command
11 0°FNFJUUL
Intake air thermo sensor (dynamic chamber)
Short circuit Maintains constant 20°C (68°F) command
12
Throttle sensor Open or short circuit Maintains constant command of throttle valve fully open
15 ON n
OFF •L 01
Oxygen sensor Sensor output con-tinues less than 0.55V 120 sec. after engine starts (1,500 rpm or over)
Cancels
EG I
feed-
back operation
17 ON n
OFF L HI il
Feedback system Sensor output not changed 20 sec. af-ter engine starts (1,500 rpm or over)
Cancels
EG I
feed-
back operation
25 0°nfJU1LJIL
Solenoid valve (pres-sure regulator control)
Open or short circuit
26 2LMJIL
Solenoid valve (No.1 purge control)
Open or short circuit
27 ON nn
OFF | _ •111
-ii-Solenoid valve (No.2
purge control)
Open or short circuit
28 ON nn
OFF L Hi nr
Solenoid valve (EGR)
Open or short circuit
34 ^jmiHum
Solenoid valve (Idle speed control)
Open or short circuit
36 °FFJMI«U
Oxygen sensor relay
Open or short circuit
41 <£jimjiuM
Solenoid valve (Vari-able inertia control)
Open or short circuit
76G04C-018
Caution
a) If there is more than one failure present, the lowest number malfunction code is dis-
played first, the remaining codes are displayed sequentially.
b) After repairing a failure, turn off the ignition switch and disconnect the negative battery
cable and depress the brake pedal for at least 5 seconds to erase the memory of a mal-
function code.
4C—15

4C TROUBLESHOOTING WITH SST
Is there continuity between air flow sensor and
engine control unit?
Air flow sensor Engine control unit
D (RB wire) 2E
E (RW wire) 2B
NO
YES
Is there 12V at terminal B of air flow sensor connector? (Refer to page 4C—103)
YES
Is there continuity between terminal F of air flow sensor and ground? (Refer to page 4C-103)
YES
NO
NO
PC: Open circuit in wiring harness
PC: Open or short circuit in wiring harness from terminal B to control relay
PC: Open circuit in wiring harness
PC: • Engine control unit malfunction • Short circuit in wiring from terminal D of air flow sensor to engine control unit
76G04C-022
Code No. 09 (Water thermo sensor)
Are there poor connections in water thermo sensor circuit?
NO
Is there continuity between water thermo sensor and engine control unit?
YES
Is resistance of the water thermo sensor OK? Resistance:
YES
Water thermo sensor Enaine control unit
A (YB wire) 21
B (LgY wire) 2C
NO
Coolant temp Resistance
-20°C ( —4°F) 14.5-17.8 kfl
20°C ( 68°F) 2.2- 2.7 kfi
40°C {104°F) 1.0- 1.3 kfi
60°C (140°F) 500-640 fi
80°C (176°F) 280-350 fi
NO
YES
Is same Code No. present after performing after-repair procedure? (Refer to page 4C—12)
YES
Are engine control unit 21 and 2C terminal voltages OK? (Refer to page 4C—98)
YES
NO
NO
PC: Possible Cause
Repair or replace connector
PC: Open circuit in wiring harness from water thermo sensor to engine control unit
Replace water thermo sensor
Water thermo sensor and circuit OK
PC: Short circuit in wiring harness
PC: Engine control unit malfunction
76G04C-023
4C—18

4C TROUBLESHOOTING WITH SST
Code No. 26 (Solenoid valve—No. 1 purge control) PC: Possible Cause
YES
YES
Is there continuity between solenoid valve and engine control unit?
Solenoid valve Engine control unit
WG wire 2P
NO PC: Open circuit in wiring harness from solenoid valve to engine control unit
YES PC: • Engine control unit malfunction • Short circuit in wiring harness
76G04C-029
Code No. 27 (Solenoid valve—No. 2 purge control) PC: Possible Cause
Are there poor connections in solenoid valve circuit? YES Repair or replace connector
NO
NO Is there continuity of solenoid valve? NO Replace solenoid valve
YES
Is there battery voltage at RB wire of solenoid valve connector?
NO PC: Open circuit in wiring harness from RB wire to
control relay (for engine control unit)
YES
Is there continuity between solenoid valve and en-
gine control unit?
Solenoid valve Enaine control unit
WB wire 20
NO PC: Open circuit in wiring harness from solenoid valve to engine control unit
YES PC: • Engine control unit malfunction • Short circuit in wiring harness
76G04C-030
4C—22