1987 MAZDA 626 oil

2B OIL PUMP
OIL PUMP
REMOVAL
1. Disconnect the negative battery cable.
2. Drain the engine oil and coolant.
3. Remove in the sequence shown in the figure referring to the removal note for specially marked parts.
76G02B-026
6. Oil pan (Refer to page 2B—9)
7. Stiffener (RF-CX)
8. Oil strainer
9. Oil pump
Removal Note
Timing belt pulley lock bolt
Hold the timing belt pulley with the SST and remove
the lock bolt.
1. Timing belt (Refer to page 1C—11)
2. Camshaft pulley (Refer to page 1C—36)
3. Injection pump pulley (Refer to page
1C—36)
4. Seal plate
5. Timing belt pulley
2B-12

OIL PUMP 2B
DISASSEMBLY
Disassemble in the sequence shown in the figure. 69G02B-012
INSPECTION
1. Check the following and replace any faulty parts.
(1) Distorted or damaged oil pump body or cover
(2) Worn or damaged plunger
(3) Weak or broken plunger spring
2. Measure the side clearance.
Clearance:
0.14 mm (0.006 in) max.
3. Measure the tooth tip clearance.
Clearance: 0.24 mm (0.009 in) max.
2B-13

76G02B-031
76G02B-032
ASSEMBLY
Assemble the pump as follows.
Oil Seal
1. Apply engine oil to the pump body and the out-
side of the new oil seal. 2. Press in the oil seal.
Pressure Relief Valve
1. Install the plunger and spring in the pump body.
2. Install the spring seat plug and tighten to specifi-
cation.
Tightening torque:
26—39 N-m (2.7—4.0 m-kg, 20—29 ft-lb)
Outer and Inner Rotor
Install the rotors with the assembly mark facing the
pump cover.
Oil Pump Cover
1. Apply thread locking compound to the cover
mounting screws' threads.
2. Attach the oil pump cover to the body.
Tightening torque:
6—9 N-m (60—90 cm-kg, 52—78 in-lb)
76G02B-037
INSTALLATION
Install in the reverse order of removal referring to in-
stallation note.
Installation Note
Oil pump
1. Apply grease to a new O-ring and install it in the
oil pump body.
2. Apply silicon sealant to the shaded area as shown
in the figure.
3. Apply engine oil to the oil seal lip.
76G02B-033
2B-14

OIL JET 2B
OIL JET
REMOVAL
Remove each part in the following order.
1. Remove the oil pan. (Refer to page 2B—9).
2. Remove the oil jet valve.
3. Remove the oil jet.
76G02B-034
INSPECTION
1. Make sure that the oil passage is not clogged.
2. Check that the oil jet valve is not stuck or damaged.
INSTALLATION
Install in the reverse order of removal.
Tightening torque: 12—18 N-m
(1.2—1.8 m-kg, 104—156 in-lb)
76G02B-035
2B—15

3A OUTLINE
OUTLINE
COOLANT FLOW CHART (DOHC)
ISC solenoid valve 2-stage thermostat
From jo heater heater Main*™, valve ^--^Sub valve
76G03A-002
1. Water pump
2. Thermostat
3. Radiator
4. Coolant reservoir
5. Oil cooler
6. Cooling fan
3A—2

OUTLINE 3A
COOLANT FLOW CHART (SOHC)
76G03A-015
1. Water pump 4. Coolant reservoir
2. Thermostat 5. Oil cooler (8-valve...only ECE, 12-valve)
3. Radiator 6. Cooling fan
3A—3

COOLANT 3A
76G03A-016
69G03A-006
COOLANT
INSPECTION
Coolant Level (Engine cold)
1. Check that the coolant level is near the radiator inlet
port.
2. Check that the coolant level in the coolant reser-
voir is between the FULL and LOW marks.
Add coolant if necessary.
Warning
a) Never remove the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
removing it.
Coolant Quality
1. Check that there is no build-up of rust or scales
around the radiator cap or radiator filler neck.
2. Check that coolant is free from oil.
3. Replace the coolant, if necessary.
Coolant Leakage
1. Connect a tester and SST to the radiator inlet port.
2. Apply 103 kPa (1.05 kg/cm2, 15 psi) pressure
to the system.
3. Check that the pressure is held.
If not, check for coolant leakage.
Warning
When removing either the radiator cap or the
tester, loosen it slowly until the pressure in
the radiator is released, and then remove it.
86U03X-005
REPLACEMENT
1. Remove the radiator cap and loosen the drain plug.
2. Drain the coolant into a suitable container.
Warning
a) Never open the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
loosening.
c) Use caution when draining hot coolant.
86U03X-006
3A-5

3A WATER PUMP
INSPECTION
Check the following. Replace the pump if necessary.
1. Cracks or damage
2. Abnormal noise, bearing sticking or loose.
86U03X-014
INSTALLATION
Install in the reverse order of removal referring to the
installation note.
Installation Note
Rubber seal
Install the rubber seals on the water pump.
76G03A-017
86U03X-016
Water pump
1. Remove any gasket fragments, dirt, or oil from the
contact surfaces.
2. Install a new O-ring on the water pump.
3. Install the water pump.
Tightening torque:
19—25 Nm (1.9—2.6 m-kg, 14—19 ft-lb)
Note
To prevent dropping the O-ring when install-
ing, put silicon sealant in the O-ring groove
(shaded areas) as shown. Do not apply it to
the contact surfaces.
3A—10