1987 MAZDA 626 wheel bolts

7A INSTALLATION
76G07A-063
76G07A-064
18. Install the left driveshaft as follows:
(1) Pull the front hub outward and insert the
driveshaft into the transaxle.
(2) Push the joint at the differential side to connect
the driveshaft to the differential side gear.
Note
a) Do not damage the oil seal.
b) After installation, pull the front hub outward
to confirm that the driveshaft doesn't come
out.
19. Install the lower arm ball joints to the knuckles and
tighten the bolts and nuts.
Tightening torque: 43—54 N-m
(4.4—5.5 m-kg, 32—40 ft-lb)
20. Install the under cover, (except DOHC)
Note
Before installation, fill the notches with sili-
con as shown in the figure.
Tightening torque: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
21. Install the stabilizer bar control links as follows.
(1) Install the stabilizer bar control link.
(2) Adjust protrusion to 20.1 mm (0.79 in)
(3) Tighten bolt to specified torque.
Tightening torque: 16—23 N-m
(1.6—2.3 m-kg , 12—17 ft-lb)
76G07A-065
76G07A-066
22. Install the tie-rod ends and new cotter pine.
Tightening torque: 29—44 N-m
(3.0—4.5 m-kg, 22—33 ft-lb)
23. Install the splash shields.
Tightening torque: 8—11 N-m
(80—110 cm-kg, 69—95 in-lb)
24. Install the front wheels.
Tightening torque: 88—118 N-m
(9.0—12.0 m-kg, 65—87 ft-lb)
—56

REMOVAL 7B
12. Remove the front wheels.
13. Remove the splash shields.
14. Drain the ATF.
15. Disconnect the oil cooler outlet and inlet hoses.
76G07B-111
16. Disconnect the tie-rod ends with the SST.
76G07B-112
17. Remove the stabilizer bar control links.
18. Remove the bolts and nuts at the left and right low-
er arm ball joints.
19. Pull the lower arms downward to separate them
from the knuckles.
Caution
Do not damage the ball joint dust boots.
76G07B-113
20. Separate the left driveshaft from the transaxle by
prying with a bar inserted between the shaft and
the case.
Caution
Do not damage the oil seal.
21. Remove the joint shaft bracket.
22. Separate the right driveshaft together with the joint
shaft in the same manner.
76G07B-114
7B—85

INSTALLATION 7B
86U07B-453
86U07B-454
76G07B-198
20. Install the tie-rod ends and cotter pins.
Tightening torque:
29—44 N-m (3.0—4.5 m-kg, 22—33 ft-lb)
21. Install the oil cooler outlet and inlet hoses.
22. Install the splash shields.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
23. Install the front wheels.
Tightening torque:
88—118 N-m (9—12 m-kg, 65—87 ft-lb)
24. Connect the throttle cable.
Note
Adjust the throttle cable with the oil pressure
test. (Refer to page 7B—75, 76)
25. Connect the selector cable.
Tightening torque:
Nut
29—39 N-m (3.0—4.0 m-kg, 22—29 ft-lb)
Bolts
16—22 N-m (1.6—2.3 m-kg, 12—17 ft-lb)
26. Connect the ground wires to the transaxle case.
Tightening torque:
8—11 N-m (80—115 cm-kg, 69—99 in-lb)
86U07B-456
7B—219

7C REMOVAL
REMOVAL
PREPARATION
(1) Drain the ATF before removal.
(2) Attach the engine support.
(3) Jack up the vehicle and support it with safety stands.
Components
1. Battery
2. Battery carrier
3. Fresh air duct
4. Main fuse block
5. Distributor leads
6. Speedometer cable
7. Cnnectors
8. Ground wires
9. Selector cable
10. Vacuum hose
11. Front wheels
12. Splash shields
13. Oil cooler outlet and inlet
hoses
14. Tie-rod ends
15. Stabilizer bar control links
16. Lower arm ball joints
17. Driveshaft
18. Joint shaft bracket
76G07C-056
19. Joint shaft and driveshaft
20. Under cover
21. Torque converter bolts
22. Starter
23. Engine mount No.4
24. Engine mount No.2
25. Crossmember and left side
lower arm
26. Transaxle
7C-30

INSTALLATION 7C
76G07C-332
19. Install the oil cooler outlet and inlet hoses.
Note
Align the mating mark as shown.
20. Install the splash shields.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
21. Install the front wheels.
Tightening torque:
88—118 N-m (9—12 m-kg, 65—87 ft-lb)
22. Connect the vacuum hose.
23. Connect the selector cable.
Tightening torque:
Nut
44—64 N-m (4.5—6.5 m-kg, 33—47 ft-lb)
Bolts
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
76G07C-333
24. Connect the ground wires
to
the transaxle case and
oil pump.
Tightening torque:
8—11 N-m (80—110 cm-kg, 69—95 in-lb)
76G07C-334
25. Connect the connectors.
(1) Inhibitor switch
(2) Kick-down switch
26. Connect the speedometer cable.
76G07C-335
7C—123

FRONT AXLE 9
ASSEMBLY
1. Install new hub bolts. (If applicable)
2. Install a new dust cover with the SST.
86U09X-017
3. Install a new front wheel bearing with the SST.
86U09X-018
4. Install the retaining ring.
5. Install a new oil seal with the SST.
Note
Apply grease to the oil seal lip.
86U09X-019
li s
I >M tf
49 H026 103
H
6. Install the front wheel hub with the SST.
86U09X-020
9—13

REAR AXLE 9
DISASSEMBLY
Disassemble in the sequence shown in the figure referring to the disassembly note for the specially
marked parts.
1. Oil seal
2. Sensor rotor (ABS)
3. Retaining ring
4. Rear wheel bearing
5. Disc plate
86U09X-042
S 49 0839 425C
49 F027 007
86U09X-087
Disassembly Note
Note
a) Do not remove the hub bolts unless
necessary.
b)Do not reuse the hub bolts if removed.
Sensor rotor (ABS)
Remove the sensor rotor with the SST.
Note
a) Do not remove the sensor rotor unless
necessary.
b)Do not reuse the sensor rotor if removed.
Rear wheel bearing
Remove the rear wheel bearing with the SST.
Note
Do not reuse the rear wheel bearing if
removed.
86U09X-085
9-23

REAR AXLE 9
ASSEMBLY
1. Install new hub bolts.
86U09X-045
2. Install a new sensor rotor with the SST. (ABS)
86U09X-046
3. Install a new rear wheel bearing with the SST.
4. Install the retaining ring.
86U09X-047
5. Install a new oil seal with the SST.
Note
Apply grease to the oil seal lip.
86U09X-048
9—25