1986 TOYOTA CAMRY V20 torque

5. FILL DIFFERENTIAL WITH GEAR OIL
(a) Install the drain plug with new gasket.
Torque: 500 kg±cm (36 ft±Ib, 49 N±m)
(b) Fill the differential with gear oil.
Oil grade: API GL±5 hypoid gear oil
Viscosity: Above ±18
°C (0°F) SAE 90
Below ±18°C
(0°F) SAE 80W±90
Capacity: 1.1 liters (1.2 US qts, 1.0 lmp.qts)
(c) Install the filler plug with new gasket.
Torque: 400 kg±cm (29 ft±lb, 39 N±m)
INSTALLATION OF DIFFERENTIAL
(See page RA±27)
1. INSTALL DIFFERENTIAL
(a) Position the differential and torque the four bolts and nuts.
Torque: 970 kg±cm (70 ft±Ib. 95 N±m)
2. CONNECT PROPELLER SHAFT
(a) Align the matchmarks on the flanges and connect the
flanges with four bolts, nuts and washers.
(b) Torque the four bolts and nuts.
Torque: 750 kg±cm (54 ft±lb, 74 N±m)
4. CONNECT DRIVE SHAFTS (See page RA±131) (b) Install and torque the two bolts.
Torque: 1,500 kg±cm 108 ft±lb, 147 N±m)
± REAR AXLE AND SUSPENSIONDifferential (4WD)RA±49

INSTALLATION OF REAR SHOCK
ABSORBER
1. INSTALL SPRING BUMPER, INSULATOR, COIL
SPRING, AND SUSPENSION SUPPORT
(a) Mount the shock absorber in a vise.
(b) Using SST, compress the coil spring.
SST 09727±22032 or 09727±30020
(e) Install the lower insulator to the shock absorber.
(d) Align the coil spring end with the lower seat hollow and
install the coil spring.
(e) Install the spring bumper to the shock absorber piston
rod.
(f) Install the upper insulator.
(g) Align the suspension support with the piston rod and
install it.
(h) Align the suspension support.
3. CONNECT AXLE CARRIER TO SHOCK ABSORBER
Connect the axle carrier to the shock absorber with the
two bolts and torque the two nuts.
Torque: 2,300 kg±cm (166 ft±lb, 226 N±m)
2. INSTALL SHOCK ABSORBER TO BODY
Install the shock absorber to the body and torque the
three n uts.
Torque: 400 kg±cm (29 ft±Ib, 39 N± m)
(i) Using SST, hold the suspension support and
install and torque a new lock nut.
Torque: 500 kg±cm (36 ft±Ib, 49N±m)
± REAR AXLE AND SUSPENSIONRearRA±53

4. INSTALL BRAKE HOSE AND TUBE
(a) Temporarily connect the brake tube to the backing
plate.
(b) Temporarily connect the brake tube to the brake hose.
(c) Install the clip.
(d) Using SST, torque the two brake tube union nuts.
SST 09751±36011
Torque: 155 kg±cm (11 ft±Ib, 15 N±m )
5. INSTALL TONNEAU COVER HOLDER (Wagon)
6. BLEED BRAKE LINE
(See page BR±7)
7. CHECK WHEEL ALIGNMENT
(See page RA±3)
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±54

6. TORQUE NO.1 AND NO.2 SUSPENSION ARM
INSTALLATION BOLTS
(a) Align the matchmarks on the cam and the body torque
the installation bolt with the vehicle weight on the
suspension.
Torque: 1,150 kg±cm (83 ft±Ib, 113 N±m)
3. CONNECT NO.1 AND NO.2 SUSPENSION ARM TO
AXLE CARRIER
Connect the No. 1 and No.2 suspension arms with the
bolt and the two retainers to the axle carrier and tempo-
rarily install the nut.
5. INSTALL WHEELS AND LOWER VEHICLE
(a) Install the wheels.
(b) Remove the stands and bounce the vehicle up and
down to stabilize the suspension. 4. CONNECT STRUT BAR TO AXLE CARRIER
Connect the strut rod to the axle carrier and temporarily
install the bolt and nut.(a) Place the No.2 suspension arm in position.
(b) Temporarily install the cam bolt and cam to the
body.
± REAR AXLE AND SUSPENSIONRear Suspension (FIND)RA±57

Strut Rod
(See page RA±50)
REMOVAL OF STRUT ROD
REMOVE STRUT ROD
(a) Remove the strut rod installation bolt and nut from the
axle carrier. 7. TORQUE STRUT ROD INSTALLATION BOLT TO AXLE
CARRIER
Torque the strut rod installation bolt to the axle carrier
with the vehicle weight on the suspension.
Torque: 1,150 kg±cm (83 ft±Ib, 113 N ± m)
8. INSTALL FUEL TANK PROTECTOR
Install the fuel tank protector with the two bolts and the
two clips.
9. CHECK REAR WHEEL ALIGNMENT(b) Torque the suspension arm installation bolt to the
axle carrier with the vehicle weight on the sus-
pension.
Torque: 1,850 kg±cm (134 ft±Ib, 181 N ± m)
(b) Remove the strut rod installation bolt and nut from the
body.
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±58

Strut Rod
(See page RA±50)
REMOVAL OF STRUT ROD
REMOVE STRUT ROD
(a) Remove the strut rod installation bolt and nut from the
axle carrier. 7. TORQUE STRUT ROD INSTALLATION BOLT TO AXLE
CARRIER
Torque the strut rod installation bolt to the axle carrier
with the vehicle weight on the suspension.
Torque: 1,150 kg±cm (83 ft±Ib, 113 N ± m)
8. INSTALL FUEL TANK PROTECTOR
Install the fuel tank protector with the two bolts and the
two clips.
9. CHECK REAR WHEEL ALIGNMENT(b) Torque the suspension arm installation bolt to the
axle carrier with the vehicle weight on the sus-
pension.
Torque: 1,850 kg±cm (134 ft±Ib, 181 N ± m)
(b) Remove the strut rod installation bolt and nut from the
body.
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±58

3. TORQUE STRUT ROD INSTALLATION BOLTS AND
NUTS
Torque the mounting bolt with the vehicle weight on the
suspension.
Torque: 1,150 kg±cm (83 ft±Ib, 113 N± m)
4. CHECK WHEEL ALIGNMENT
(See page RA±3)
INSTALLATION OF STRUT ROD
1. INSTALL STRUT ROD
(a) Position the strut rod to the body and temporarily install
the bolt and nut.
HINT: Be sure the lip of the nut is resting on the flange of
the bracket as shown in the figure.
2. INSTALL WHEELS AND LOWER VEHICLE
(a) install the wheels.
(b) Remove the stands and bounce the vehicle up and
down to stabilize the suspension. (b) Temporarily connect the strut rod with the bolt and
nut.
HINT: Be sure the lip of the nut is resting on the
flange of the bracket as shown in the figure. .
± REAR AXLE AND SUSPENSIONRearRA±59

2. PLACE STABILIZER BAR
3. CONNECT TANK BAND TO BODY
Position the fuel tank in position, connect the tank
bands to the body and torque the installation bolts.
Torque: 400 kg±cm (29 ft±Ib, 39 N±m )
INSTALLATION OF STABILIZER BAR
1. INSPECT STABILIZER LINK
Move the ball joint stud in all directions, if the movement is
not smooth and free, replace the stabilizer link.
4. INSTALL STABILIZER BAR TO BODY
(a) Install the cushion and brackets to the stabilizer bar.
(b) Torque the four bolts.
Torque: 195 kg±cm (14 ft±Ib, 19 N±m)
6. CONNECT STABILIZER LINK TO SHOCK ABSORBER
Torque: 650 kg±cm (47 ft±Ib, 64 N±m)
5. INSTALL STABILIZER LINK TO STABILIZER BAR
Torque: 650 kg±cm (47 ft±Ib, 64 N± m)
± REAR AXLE AND SUSPENSIONRear Suspension (FWD)RA±61