1986 TOYOTA CAMRY V20 coolant

Fuel tank band x Body
Cold start injector x Air intake chamber
Cold start injector pipe x Cold start injector
Cold start injector pipe x Delivery pipe
Fuel pressure regulator X Delivery pipe
Fuel return pipe x Fuel pressure regulator
Delivery pipe x Cylinder head
Throttle body x Air intake chamberFuel evaporation vent tube x Fuel tank 4WD
Fuel inlet pipe x Fuel tankFuel sender gauge
Fuel pump X Fuel tank
Specifications (Cont'd)
Torque Specifications
Coolant temp. 805C (1765F) Intake air temp. 205C (685F) Measuring plate fully closed
Measuring plate fully openThrottle valve fully closed
Throttle valve fully closedThrottle valve fully closedThrottle valve fully closed
Throttle valve fully openThrottle valve fully open
* 1 w/o ECT *2 w/ ECT Throttle valve openThrottle valve open
Part tightened ECU (cont'd) Resistance
Condition
Fuel line
± SERVICE SPECIFICATIONSEFI System (3S±FE)A±13

Engine coolant x Drain plug
Water pump x Water pump cover
Water pump x Cylinder head
Water by±pass pipe X Water pump
Water inlet housing x Water pump
Oil cooler x Radiator tower tank
Cylinder block x Drain plug
Water pump x Cylinder block
Water inlet x Water pump
Water inlet pipe x Alternator belt adjusting bar
LUBRICATION SYSTEM (3S±FE)
SpecificationsTorque Specifi
cations (3S±FE)
COOLING SYSTEM
Specifications
Torque Specifications (2VZ±FE)
Valve opening temperature
Valve lift at 95°C (203°F) Relief valve opening pressure
Engine coolant capacityEngine coolant capacity
at Idling
at 3,040 rpm
STD
Limit
STD
Limit Body clearance .See page A±20 STD
Limit
Part tightened
Part tightenedSee page A±2
Tip clearance3S±FE
2VZ±FE
Oil pressureThermostat
Oil pumpRadiator
± SERVICE SPECIFICATIONSCooling SystemA±17

HINT:
wPerform all voltage and resistance measurements with the ECU connected.
wVerify that the battery voltage is 11 V or above with the ignition switch is ON.
No trouble (ºCHECKº' engine warning light off) and
engine running
Specifications (Cont'd)
Stop light SW ON (Brake pedal depressed)Check connector TE1 ± E1 not connected
Check connector TE1 ± Et connected
Shift position P or N range
Ex shift position P or N rangeIntake air temp. 205C (685F) Measuring plate fully closed
Coolant temp. 605C (1765F) Measuring plate fully open Throttle valve fully closed
Heater blower SW ON Air conditioning ONThrottle valve open
Throttle valve open
Cranking or idling Heater resistance
STD voltage (V) Oxygen
sensor
IG SW ON
IG SW ONIG SW ON
IG SW ONIG SW ON
IG SW ONCranking Terminals
Condition Voltage
Idling
*1 w/ rpm ECU
± SERVICE SPECIFICATIONSEFI System (2VZ±FE)A±15

Fuel pump x Fuel tank
Fuel inlet pipe x Fuel tank
Fuel tank band x Body
Cold start injector x Air intake chamber
Cold start injector tube x Cold start injector
Cold start injector tube x Delivery pipe
Fuel pressure regulator x Delivery pipe
Delivery pipe x Intake manifold
No. 2 fuel pipe x Delivery pipe
Air intake chamber x Intake manifold
EGR pipe nut
No. 1 engine hanger
Air intake chamber stay
No. 1 RH engine mounting stay x Air intake chamber
No. 1 RH engine mounting stay x RH engine mounting insulator
Throttle body x Air intake chamber
ISC valve x Air intake chamber
Specifications (Cont'd)
Torque Specifications
Intake air temp. 20°C (68°F) Measuring plate fully closed
Coolant temp. 60°C (176°F)
Union bolt type
Flare nut type Measuring plate fully open Throttle valve fully dosed
Throttle valve fully closedThrottle valve fully open Throttle valve openSTD resistance (fl)
Part tightened ECU (cont'd)
Resistance
Terminals
Condition
Fuel line
± SERVICE SPECIFICATIONSEFI System (2VZ±FE)A±16

Engine coolant x Drain plug
Water pump x Water pump cover
Water pump x Cylinder head
Water by±pass pipe X Water pump
Water inlet housing x Water pump
Oil cooler x Radiator tower tank
Cylinder block x Drain plug
Water pump x Cylinder block
Water inlet x Water pump
Water inlet pipe x Alternator belt adjusting bar
LUBRICATION SYSTEM (3S±FE)
SpecificationsTorque Specifi
cations (3S±FE)
COOLING SYSTEM
Specifications
Torque Specifications (2VZ±FE)
Valve opening temperature
Valve lift at 95°C (203°F) Relief valve opening pressure
Engine coolant capacityEngine coolant capacity
at Idling
at 3,040 rpm
STD
Limit
STD
Limit Body clearance .See page A±20 STD
Limit
Part tightened
Part tightenedSee page A±2
Tip clearance3S±FE
2VZ±FE
Oil pressureThermostat
Oil pumpRadiator
± SERVICE SPECIFICATIONSLubrication System (3S±FE)A±17

Engine oil drain plug
Oil pump body cover x Oil pump body
Oil pump x Cylinder block
Oil strainer x Cylinder block
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
Oil pan x Drain plug
Oil pump. x Cylinder block
Oil strainer x Main bearing cap
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Oil pan X Rear oil seal retainer
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
LUBRICATION SYSTEM (2VZ±FE)
Specifications
Torque SpecificationsTorque Specifications
Engine coolant capacity
Body clearanceSee page A±20
Part tightened Side clearancePart tightened
Tip clearance Oil pressure
Oil pump
± SERVICE SPECIFICATIONSLubrication System (3S±FE)A±18

Engine oil drain plug
Oil pump body cover x Oil pump body
Oil pump x Cylinder block
Oil strainer x Cylinder block
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
Oil pan x Drain plug
Oil pump. x Cylinder block
Oil strainer x Main bearing cap
Oil strainer x Oil pump
Oil pan x Cylinder block
Oil pan x Oil pump
Oil pan X Rear oil seal retainer
Stiffener plate x Cylinder block
Stiffener plate x Transaxle case
LUBRICATION SYSTEM (2VZ±FE)
Specifications
Torque SpecificationsTorque Specifications
Engine coolant capacity
Body clearanceSee page A±20
Part tightened Side clearancePart tightened
Tip clearance Oil pressure
Oil pump
± SERVICE SPECIFICATIONSLubrication System (2VZ±FE)A±18