
Downloaded from www.Manualslib.com manuals search engine NOTICE: Use only trailer hitches which permit normal operation of the Energy Absorbing Bumper System. if so equipped. For example. a rigid fore and .iUt connection between the bumper and any other part.of. the car may increase  .damage in the event of II collision. 
TRAILER TOWING TIPS 
Getting Started 
Before entering  traffic with a frailer  that has electric  brakes, start the car  and 
trailer  moving  and apply  the trailer  brakes 
by hand to be sure the trailer  brakes 
are  working  and the trailer  electrical  system 
is connected  . 
. Engine Cooling 
:
When  going up long  grades,  you, can  reduce  the chance  'of engine  overheating  by 
turning 
off the  air conditioner, if so equipped. 
Transaxle 
,See the  method  for checking  the transaxle fluid le ve l. in "Service and 
,.;.Maintenance,"  Section 5 of this manual . 
Parking 
You should  not park  cars with  trailers  on a grade (hill).  However, if you must 
park  on a grade,  these steps must be followed: 
1. Apply  the regular  brakes. 
2. Have someone  place wheel' chocks under the  trailer  wheels. 
3. When  the wheel  chocks  are in place,  release  the regular  brakes until the 
chocks  absorb the load . 
4; Apply Ihe parking  brake. 
S. Shift Ihe transaxle 10 ··P"(Park). 
If the car is parked  on a grade.  don't shift the transaxle 10 "P"(Park) until  the 
trailer  wheels 
are chocked  and the parkinghrake, is set~ If you do, the weight of . the  car  and  trailer  may put so much force on the  parking  pawl in the  transaxle 
. 
that it  may be hard  to shift  oul of "P"(Park). 
When  starting , after  being parked ' on a grade: 
(; Apply  the regular  brakes and hold. 
2 . 
Stan th e engine  in ··P"(Park) . 
-3. Shift into gear  and release  the parking  brake. 
4. Release the regular  brakes and drive  until the chock s are  free. 
5. Apply  the regular  brakes and have  your  helper  remove  the chocks. 
J.]3   

Downloaded from www.Manualslib.com manuals search engine NOTICE: If the engine runs for a long time (5 minute. or more) without pressing down the accelerator pedal. overheeting cOuld calise damage to the engine end exhaust system. 
Do not INve your car unattend4Mt with the engine running . If the engine shoukt overheat you would not be there to react to the temperature warning light or gage. This could r.sult in costly damage to your car and its contents. 
• WARM ENGINE -Be ,sur e to  follow  the instructi ons  which  apply to your engine . (The  Engine  Code is 'th e 5th digit  on the  YIN  plate  at the  lower  left 
sid e  o f yo
ur windshield . (See  "Specifications,"  Secti o n 7  for  more  details .) 
• Engine Code 5 • Press down the accelerator pedal to 1/3 of 
its travel and hold. Crank  the engine by turnin g the igniti on  ke y to "Star  .. " Rel ease  the  key  and  accelerator  pedal when the _ engine s tart s. 
• Engine Code 7 . Do not press down the accelerator pedal. 
With your foot off the pedal. crank th e  engine by turning the 
ignition  key to ·'Start." If  t he  engine  does no t start after  3 seconds  ,o f 
.  c ranking,  press' 
down the accelerator  pedal to 1/3 of its  travel  while 
c ranking.  Release the key ,(ap.d accelerator  pedal) when the  engine  starts . 
• Very Cold Weather (Below·' B OC or O °F Or After Car Has Been 
Standing Idle Several Days) - Befor e crankin g th e en gine , fully  depress 
and  release  the acce le rat or  pedal  one  or  two  times more  than  slated  fo r  your 
engine  under "Cold  Engine" s ta rt ing . Then . with your foot off the accelerator pedal,-cra nk the  engine -b y-turnin g the  ig nit io n key to  "St art ." 
Rdease the key  when  the  e ngin e  s tarts. 
4 .  Appl y th e regular  brakes  and  shift  into  the prop
er g~r. Release  the parkin g 
b ra k e  a nd  drive  off. 
," '. ." 
If Engine Fails To Start 
t. Fully depr ess  and  release  the acce le rat or pedal severa l times~ then tak e your 
foo t ofT th e peda _' and  cra nk  the  e ngine  by  turnin g the key to  ··St art." 
2. If th e  e ng in e still does not  sta rt,  press  the  accele ra to r  peda l to the floo r an d 
h old it ther e while  cra nkin g the· e ng ine. -Thi s sh ould clear  the  eng in e  i f it is 
floode d. 
3. If th e  en gine has been floode d' with too  much  fuel ,  it  m ay  start  to run  but 
n ot  h ave  enough  power to  keep  running. 
In that case,  continue  cranking  with 
th e accel erator  pedal  all th e  way  to the  floor  until  t he  e ngin e clears itsel f of 
excess ' gaso line an d  run s sm oo thly. 
TRANSAXlE 
CAUTION: Before going down ,e steep of'long grade . reduce speed and shift the transa.xle into a lower gear or lower g.ar range to control vehicle speed . (Do this with either 8n automatic or a manual  ,transaxle).Try not to hold the brakcl pedal down too long or too often. This could,cause the brakes to get hO,t  and not work as well. 
Driving on Slippery Surfaces 
Take  ca re  w he n  speedin g up . or  when  shiftin g  into  a  l ower  gear,  or  lower  gea r 
r a n
ge w hile  drivin g  o n slippe ry  surf aces.  Sudde n acce le ra tio n or en gine bra kin g 
a c tion  (du e to  shifting 
to a  lower  gear)  could -ca use the  f ron t wheels  to  s kid . 
N orm al 
skid  correction  and cautio us :dr iving are  call ed for  at  these times . 
2·9   

Downloaded from www.Manualslib.com manuals search engine CAUTION: Driving thr~gh water deep enough to wet the brakes may cause the brakes not to work as well. As 8 result the vehicle will not slow down at the usual 
rate ; and it may pull to the right or left. After checking to the rear for other vehicle., apply the brakes lightly to check whether this has happened. To dry them quickly, lightly apply the brakes. At the-same time, k .. p a safe forward speed, with plenty of clear space ahead, to the rear, and to the side •. 00 this until the brakes return to normal. 
The  brake  system  warning light is covered  in the "Instrument  Panel" section. 
Power Brakes 
• If optional  power  assis t is lost  because of a stalled  engine or other  reasons . 
the  brakes can normally  still be applied with power  assist at leas t two  times 
u sing  reserv e power. 
• Th e system is designed  to bring  the vehicle  to a full  stop  on reserve  power if the brake  pedal is applied  once and held  down . However . the reserve power 
is partly used  up  each  time the brake  pedal is applied  and rele ased.  Do  not 
pump  the brakes  when ,brake  power  assist has been  lost, except  when needed 
to  maintain  steering  control  on slippery  surfaces. 
• Without  power assist, the  vehicle  can still be stopped by pushing  much harder 
o n  the brake  pedal.  However,  the stopping  distance may be longer. even 
though  the brakes  themselves  remain fully operational. 
Self-Adjusting Brakes 
• The brakes  on  this  vehicle  (exc,ept for  the  parking  brake) are self-adjusting. 
They  have been design ed so 
that periodic  brake adjustment is not required. 
• The drum brakes adjust themselves when  the brakes  are  firml y applied  while 
the  vehicle is moving backwards. 
• The  disc  brakes  adjust  themselve s each  time the brakes are  used. 
• If the brak e pedal  goes down  farther  than nonnal. it may be due to a lack 
of  adjustment.  To find  out if this is the case, drive backward  and forward 
a few times , applying  the brakes  firmly when going each  way. 
• See yo ur  dealer  if pedal  height  does not return  to normal,  or if there is a rapid 
increase in pedal  travel, which  could be a sign  of other  brake  trouble . 
• Also see your dealer if the parking  brake needs  adjustment' . 
NOTICE: "Riding the brake" by resting your foot on the brake pedal when not intending to brake can cause overheated brakes. This can waar out the brake linings faster and damage the brakas thamselvas, 85 well 8S waste fuel. 
DIMMER SWITCH 
The dimmer  switch that controls  the headlight  high/lo w  beam is built  into the 
turn  signal  control. See the "Steering  Column Controls" Section 2 of this manual. 
PARKING BRAKE 
• To set the  parking  brake, fully depress  the foot  pedal at the far left side. 
• For  better  holding  power, first  press  down  the regular  brake pedal with your 
right  foot. Then  hold it while  setting  the parking  brake with your lefl foo[. 
• 
To  release  the parking  brake, pull the "Brake Release" handle located  at the 
lower  left of the instrument  panel. 
• To help remind you. the brake system warning  light is  designed  to come on if the  parking brake control is not  fully  released  and the ignition  key is  on. 
2-14   

Downloaded from www.Manualslib.com manuals search engine • Never drive-the vehicle _with the  parking  brake set as this  -may  overheat  the 
reaf brakes reducing  their effectiveness  and causing  excessive  wear or damage, 
DISC BRAKE WEAR INDICATORS 
Front disc brakes  have built-in  wear indicators  that are designed  to make  a 
high-pitched 
squealing or cricket-like  warning sound when the brake linings  are 
worn 10 where -new  linings  are needed. The sound  will come  and go, or be heard 
all  the  time 
when the  wheels  are rolling,  and when  the brake  pedal is pu~hed down 
firmly . Expensive  damage can result 
if linings  are not  replaced  when needed. 
See also the brake  checks  listed in the  Maintenance  Schedule folder. 
CLUTCH .PEDAL 
On models equiPPed with a manual  transaxle,  a clutch  pedal is used to engage 
or  disengage  the clutch,  thereby  connecting 
or disconnecting  the engine  from the 
transaxle  and drive1ine  to the  front  wheels. -When  the pedal is fully  extended  the 
clutch 
is engaged,  driving the transaxle  arid the front  wheels. 
INSTRUMENT PANEL P.ND CONTROLS 
INSTRUMENTS 
The instruments,  gages and indicator  lights conveniently  grouped in the 
instrument  cluster are des igned  to 
tell you at a glance  many important  things about 
_the perfonnance of your vehicle _, _ The following  information will enable you to 
more  quickly -understand and properly it';:rerpretthese instruments. 
Speedometer 
The  speedometer chand  ·indicatt:5 vehicle  speed in miles  per hour  and kilometers 
per  hour. 
Odometer 
The  group  of six figures . in the  speedometer  lower center  section  indicates  the 
accumulated  mileage. 
Fuel Gage 
The fuel gagewiH register the_APPROXIMATE fuel level in the tank,  when  the 
ignition 
is in  the RUN position. 
When  the gage  registers 
EMPTY, some fuel is still available as a reserve.  When 
the  gage  registers 
FULL. some additional" fuel can"still be added  to the  tank.  The 
following  conditiqns  may be considered  normal: 
• Gas station _pump may  shut  off before  fuel gage  indicates FULL.  • 
• 
Amount of gasoline  required  for fill-up  may not exactly  correspond  to gage. 
• Needle  may not move  away  from FULL until some time after fill·up. 
• Needle  may !Dove during turns. stops and-accelerations. 
When  the ignition  switch 
is turned to the OFF position,  the needle  will not 
necessarily 
retiJrn · all the  way  to the  EMPTY  mark. 
2-15   

Downloaded from www.Manualslib.com manuals search engine Make Connections In Numerical Order 
First Jumper Cable 
Discharged 
Battery 
Make Last 
onnectlon on 
Engine. Away 
from Battery 
Battery in Vehicle 
with Charged Battery LC"""=-
5. Start the engine  of the  vehicle that has  the discharged  battery. 
6. Remove the battery cables by reversing  the above  sequence  exactly. Begin 
by  removing  the last clamp first; that is, remove  the jumper cable· from the engine of the vehicle  with the' discha:r,g:edbatTery as the' first  step. 
ENGINE COOLING SYSTEM 
Your cooling  system may temporarily  overheat during severe operating 
conditions,  such as: 
• climbing  a long  hilLon  a hot qay, 
• 
stopping  after high speed  driving, 
• idling  for long periods' in' traffic, or 
• towing  a trailer. 
If theUTEMP" light  comes  on (or if you  have  a coolant  temperature  gage, the 
needle  goes 
into the warning  zone) and your  air conditioner  is on, tum it off. If 
the. 'ITEMP" light  (gage)  comes  on while  you are stopped  in traffic,  move the 
transaxle  shift lever to UN" (Neutral). If the "TBMP" light  doesn't  go off  (or  the 
gage 
needle doesn't  start to drop)  within  a minute  or two: 
3-3   

Downloaded from www.Manualslib.com manuals search engine 3. Stop the engine. Open the radiator drain valve to drain the  coolant.  (Drainage 
may  be speeded  by removing the drain  plugs in the  block.) 
4. Close  the drain  valve (install  block drain plugs,  if removed). Add water  until 
the  system  is filled and run the engine  until the upper  radiator  hose is hot again. 
5. Repeat  steps 3 and 4 several  times until the drained  liquid is nearly  colorless. 
6. Drain the system and then  close  the radiator drain  valve tightly.  (Install  block 
drain  plugs, if removed.) 
7. Disconnect  all hoses from the coolant  recovery  tank. Remove  the tank and 
pour out any fluid. Scrub and clean the inside of the tank with  soap and water. 
Flush  it well  with  clean  water, 
then drain  it. Reinstall  the tank and hoses. 
8. Add enough  water and ethylene  glycol antifreeze  (meeting GM Specification 
1899-M)to provide the required cooling, freezing, and corrosion  protection. Use a solution that is at least 50 percent antifreeze, but no more than 70 
percent  antifreeze. Fill the radiator  to the base of the filler neck and fill the 
coolant  recovery 
tank to the "Full Hot" mark. Put the recovery tank cap  back 
on. 
9. Run the  engine,  with the radiator cap removed,  until the upper  radiator  hose 
is  hot. 
10. With  the engine  idling, add coolant to the radiator  until it reaches  the bottom 
of the filler  neck.  Install  the radiator  cap, making sure the  arrows on the cap line  up with  the overflow.  tube. 
It is the owner's responsibility  to: 
• Maintain cooling system freeze protection  at _37°C (_34°F) to ensure 
protection  against corrosion and loss of coolant  from boiling. (A SO/50 
mixture of water and ethylene  glycol antifreeze will provide  freeze protection 
to ~ 37°C ore -34°P.) You should  do this  even if you don't expect  freezing 
temperatures. 
• Add ethylene  glycol base antifreeze that meets GM Specification  1899-M 
when  antifreeze 
hasto be added  because of coolant  loss or for more  protection 
' against  freezing  at temperatures  lower than _37°C (-·J4°P). 
NOTICE: Do not use alcohol or methanol-base antifreeze. or plain water alone. in your vehicle at any time. They will boil at a lower pOint than that at which the hot light indicator (or temperature gage) works. and they do not provide proper protection against corrosion. 
Radiator Pressure Cap 
The radiator  cap, a 105 kPa(15 psi) pressure  type, must be installed  tightly, 
otherwise  coolant may be lost and damage to engine  may result  from overheating. 
Radiator  pressure caps should  be checked  periodically  for proper  operation. 
If 
replacement is required, an AC cap is recommended. 
Thermostat 
The engine  coolant  temperature  is controlled  by a thermostat. It stops  coolant  flow 
through  the radiator  until a preset  temperature is reached.  This thermostat is 
installed  in 
the engine coolant  outlet on the  engine  block. The same thermostat is used in both winter  and summer.  When a replacement is needed, AC~Delco parts 
are  recommended. 
5-7   

Downloaded from www.Manualslib.com manuals search engine FUSES AND CIRCUIT BREAKERS 
The wiring circuits  in your  vehicle  are protected  from short circuits by a combination of fuses,  circuit  breakers; and fusible thermal  links in the wiring itself.  This greatly  reduces 
the  hazard of electrically  caused fires in the  automobile. 
The  fuse junction box is  located  under the right  side of the instrument panel. 
The 
headlight wiring is  protected  by a circuit breaker in the light switch.  An electrical  overload will cause  the lights  to go on an,d off, or in some cases  to remain  off. If this happens , have your headlight wiring checked  right away.  Besides  a fuse, the  windshield  wiper motor is also protected by a circuit  breaker. If the motor  overheats,  due to overloading caused by heavy  snow, etc., the  wiper ·will remain  stopped until the motor  cools. Be sure  to have  the cause  of the over· loading  corrected.  Circuit breakers  for power windows  and power door locks are located on the bulkhead  in the  engine 
compartment. 
CIRCUIT RATING 
Radio ........................................... 10 Amp. 
Wiper 
......... ......................... ......... 25 Amp . 
Stop, .Rear & Front,  Hazard  Lamps, I.P. Indicators  .. 20 Amp. 
Dir. 
Sig .. B.U.  Lamps  .............................. 20 Amp. 
Heater, 
AlC .............. ........................ 25 Amp . 
Inst. Lamps,  Radio Dial Lamp,  Heater  Dial Lamp, WIS Wiper  Lamp,  Cigarette  Lighter & Ash Tray  Lamp  ..  5 Amp. 
Gages  Warning  Lamps, Cruise Control , Brake  Alarm, 
Oil, Rear Defogger,  Fuel Gage,  Headlight  Buzzer, Seat Belt Warning  Buzzer, Temp., Gen., Idle Stop . 20 Amp. 
Glove 
Box Lamp, Dome  Lamp,  Luggage  Lamp, Clock, Hood, Cigarette  Lighter, Courtesy  Lamps, 
Key  Warning .................................... 20 Amp. 
Tail,  Parking  and 
Side Marker Lamps, License  Lamp 20 Am·p. 
Choke Heater . . . . . .  . .. .. .. . .. . . .  . . . . .. . . . . 20 Amp . 
Do 
not use fuses of higher  amperage  rating than those recom· mended  above. 
Fusible  Links are incorporated  into the wiring  system.  These 
are  wires 
of such  a gage  that they  will fuse  (or melt)  before damage occurs  to an  entire  wiring  harness in the event  of an electncal overload. See your  Chevrolet  Dealer if 1usible link replacement  becomes necessary. 
7-4 
•   

Downloaded from www.Manualslib.com manuals search engine Air Cleaner ...... . Air Conditioner 
Automat ic ............ . Malnt.nance Air  Pre •• ur •. Tire .... A ir Vents ..... Alternator (GEN) Light .. Aluminum Car •.. AM or AM·fM R.dios ..... Antifra.z . ..... ......... .......... . App.aranc. Car ...... Ashtrays & l ighters. Assi.tance. Owner .. Autom.tic DOOf lOCks 
Autom.tic: Trann.l. Malnt.mimc. Operation .. Operating Tip$  ..... Axl. , Drive .. Sabies, Reatraint of . San Joints S.ttary 
5-8 
2 -
22 5·10 5·11 2·21 2·17 .-. 2·24 (S •• "Coolant") '-1 2-20 0-1 1-2 
5-. ,-a 2 ·10 5-8 1·10 5-8 
Em.rgency SIIHting.. 3-1 Fr •• dom .... 5·9 G •• Caution... 3-1 ; GEN Light ... 2·11 T •• t Indicator... 5·9 Befortl  Oriylng  Your V.hicle ,., Belt •. Seat .... M. (S .. "Seat Baits", 
Blower, H.at.r &. Air Cond.... 2-20 Body Oamag... 4·4 Brak.s Adjustment P.dal Trav.l Traller 'Towing .. Warning Light Bre.ka,.,  Circuit 
Break·ln  Period, N.w V.hicl •... Bright Headlights ..... 
2-14 2·14 1 -11 2·17 7-4 2-' 2·7,2·14 4-4 1 -3.7·4 1-12 3-6 {S •• "Sound"l 2·18, 5-2 
Bright Metal CI.aning ......... .. Bl,llbs lit Fu ••• Bumpe ... lit Hitch ••.. 81,1mper Jack Operetion Bun.r •.. C·4 Syst.m .. C •• Coolant RaeoV.ry Tenk .. FI,I.I. Powar St •• ring .... R.diator ..... . Cap.city. Cargo W.ight ... .•. Cap3Cme •. Fluid .. C.r Br.ak·ln Period , N.w ..... . C.r Chemic. I ......... .. C.rbon Monoxid. Caution 
'-5 Inside Back Cover .-a '-7 6-12 7-1 2-' '-7 '-1 C.r. &. CI.aning, Appear.nce 4-1 C.rgo Capacity. 5-10 Cargo on Roof, C.rrying.. ......... ............... 1·3 CargoR.ck, Roof ..... 2·29 Cargo Coyer .. ................ ........... 2-27 CATALYST Indic.tor..... 2 ·18 C.t.lytic Conv.n.r C ·4 System .........  . Chains, Tir • ..... Ch.nging Whe.'s • Tiras .. Ch.rging Systam Indicator .... CHECK ENGINE light.. 
2·18,5--2 5·14 3-6 3-2 2-18, 5-2 
7-6 
Checklist. Driver  .......  . Child Seats lit Ra.traint •.. Chrome Protection .. Cigarette lightar .... Circuit Breakars . Citizens Band Radio ... " .... " .... " .. M  ••••••• Cleening .. Clock 
Cloth Trim Car." .. Clutch  Pedal Adjl,lstment.. .. Cold Welther Stlrting ..... Compla int Procedure .. 
1-1 1-10 .-. 2·20 7-' 2·2 ~ 4-1 2·20 .-, 5-8 '-a 6-1 
Conditionar,  Air ....... (See "Air Conditi on.r") Con.umer Relations... 6-1 
Cony.)! Mirror ... C ooling System Antifraet. ICoolant, .. Overheating .. Recovary Tank .. S.rvice .. Thermostat .. CorrOSion  Protection Countries. Oper.ting in Foraign ..... Cruise  Control .. Cu.tomer Sarvice .. Oamage. Sheet M.tal...-. D.fogger. Rear Window. Defro.hlT , Windshiflld .. Oalay Wipers .. Descend .ing  a Grade Trail.ring .. Dimen.ion. Dimmer Switch, H.adlight Dipsticks 
Engine Oil .. Power Staering .. Diractional  Sign." .... . Oi.c Br~ ••.. Door lock ...... 
Drrve lOOe 
1-3 
'-5 3-3 5-S '-5 5-7 .-. 2 -3 2·12 6-1 '-5 2-21 2 -20,  2·23 '-7 '-8 1-11 7-1 2-14 
'-3 .-a ,-u 2·1S 1-2 5-8 Driver Checklist.... 1·1 Driving Down Steep Gr.de........ 2·9 In Ou.ty Ar......... 5·3 on Slippery Surfaces ....... .......... ,.... 2·9 Ec;Gnomy Tips , Fu" 2·4 Electric-Powered Option...... (See  "Power") 
Ele<:tricel System 8IttMY ... ... . 
Bulbs ...... . 
Circuit Brlak.rs. , .... GEN (Glnerator) light ...... Jump Scarting .. .. Sparil Plugs .. Voltm.ter ... Erne:rg.ncy , In Ca •• of Brak. Warning  Light Engine  Hot light .. Freeing  Vahicle When Stuck ... Hazard Warning Fla.h.r .... J.cking ..... Jump 51anlng._. Towing Clr. Emission  Caution .................................. . Emi .. ion Control CAT AL YST  Indicator 
5-S 7-3 7-. 7-' 2·17 3-1 
7-2 
2·19 
2·17 2·17 3-7 
3-1 
3 ·4 .3·5 3-1 
3-7 
'-1 
2·19 
,