1969 FORD MUSTANG wheel

03-05-11

Steering Columns
And
Linkage

03-05-11

9. Check
the
operation
of the
steer-

ing tilt mechanism
(if so
equipped)

and
the
switches.

THUNDERBIRD
AND

CONTINENTAL MARK
III

Removal

1.
Remove
the
instrument panel

lower outer finish panel, instrument

panel steering column plate
and
cover.

2.
Disconnect
the
negative cable

from
the
battery.

3.
Remove
the
bolt that attaches

the flexible coupling
to the
steering

shaft.

4.
Disconnect
the
shift
rod
from
the

lever
at the
lower
end of the
column.
5.
Remove
the
four screws that
at-

tach
the
column retainer
to the
dash

panel.

6. Working from
the
underside
of

the instrument panel disconnect
the

steering column tilt-control cable from

the vacuum motor
and
mounting

bracket
(if so
equipped)
(Fig. 14).

7.
Disconnect
the
turn signal

switch,
and
emergency flasher wires
at

the connectors. Disconnect
the
wires

from
the
neutral start switch.

8. While supporting
the
steering

column, remove
the
four bolts that
at-

tach
the
lower clamp
to the
upper

clamp
(Fig. 14).
Lift
the
column from

the vehicle.

Installation

1.
Position
the
column
in the
vehi-
cle making sure that
the
steering shaft

engages
the
flex coupling.

1.
Install
the
column retainer-

to-dash panel attaching screws,
but do

not tighten them.

3.
Install
the
lower clamp
and the

attaching nuts. Tighten
the
nuts fing-

ertight.

4.
Move
the
lower flange
as re-

quired
to
center
the
steering shaft
in

the tube. Aligning procedures
are de-

tailed
in
Part
3-1.
Tighten
the
lower

flange attaching nuts when
the
shaft
is

centered.

5.
Connect
the
shift
rod to the
shift

lever
at the
lower
end of the
column.

6. Install
and
tighten
the
flex
cou-

pling attaching bolt.

7.
Tighten
the
instrument panel-

to-clamp attaching nuts.

BRAKE PEDAL SUPPORT
STEERING WHEEL-3600

TURN SIGNAL LEVER-13305

COLUMN TUBE-3514

COLUMN LOWER BRACKET-3R547

•TOE PLATE

FLEX COUPLING-3A525

G1618-A

f/G.
73—Steering Column Installation—Cougar, Mustangprocarmanuals.com

STEERING WHEEL-3600

STEERING SHAFT-3525

LOWER CLAMP

3668

CENTERING WASHER-3C708

G1542-A

:/G.
15—Steering Column (Fixed)—Disassembled—Lincoln Continentalprocarmanuals.com

03-05-14
Steering Columns And Linkage

03-05-14

8. Connect the turn signal and

emergency flasher switch wires at the

multiple connectors. Connect the wires

to the neutral start switch. Adjust-

ments for the neutral start switch are

detailed in Group 7 of this manual.

9. Connect the tilt-column control

cable to the release cable retainer and

vacuum motor (if so equipped). To re-

move cable slack, loosen the bracket

attaching screw and pull it slightly

toward the column, then tighten the

screw. If difficulty in adjusting this

control is experienced, the retainer

slot may be filed to gain additional

travel.

10.
Install the instrument panel

steering column plate and cover and

the instrument panel lower outer fin-

ish panel.

11.
Connect the negative cable to

the battery.

12.
Start the engine and check the

operation of the steering column and

switches.

LINCOLN CONTINENTAL

Removal

1.
Disconnect the battery.

2.
Disconnect the rod from the
lever at the lower end of the selector

tube.

Loosen the clamp bolt that locks

the flexible coupling to the steering

shaft.

3.
Working from the underside of

the steering wheel spoke, remove the

two screws that secure the crash pad.

Remove the pad. Do not use a ham-

mer or knock-off type wheel puller.

Striking the puller or shaft may cause

damage to the bearings and/or col-

lapsible column. Remove the steering

wheel as shown in Fig. 15.

4.
Remove the instrument panel

steering column finish plate.

5.
Remove the four screws that at-

tach the lower retainer to the dash

panel.

6. Disconnect the turn signal switch

and emergency flasher wires at the

connectors. Disconnect the wires from

the neutral start switch.

7.
While supporting the steering

column, remove the bolts that attach

the lower clamp to the upper bracket

(Fig. 15). Lift the column from the ve-

hicle.

Installation

1.
Position the column in the vehi-
cle,
making sure that the steering

shaft engages the flex coupling.

2.
Install the column retainer-

to-dash panel attaching screws, but do

not tighten them.

3.
Install the lower clamp and the

attaching nuts. Tighten the nuts fing-

ertight.

4.
Move the lower flange as re-

quired to center the steering shaft in

the tube. Aligning procedures are de-

tailed in Part 3-1. Tighten the lower

flange attaching nuts when the shaft is

centered.

5.
Connect the shift rod to the shift

lever at the lower end of the column.

6. Install and tighten the flex cou-

pling attaching bolt.

7.
Tighten the instrument panel-

to-clamp attaching nuts.

8. Connect the turn signal and

emergency flasher switch wirss at the

multiple connectors. Connect the wires

to the neutral start switch. Adjust-

ments for the neutral start switch are

detailed in Group 7 of this manual.

9. Install the instrument panel

steering column finish plate.

10.
Install the steering wheel and

crash pad.

MAJOR REPAIR OPERATIONS

STEERING COLUMN

SHIFT TUBE REPLACEMENT

STATIONARY COLUMN

WITH STANDARD

TRANSMISSION

Removal

1.
Working from the underside of

the steering wheel spoke, remove the

two screws that secure the crash pad.

Remove the pad. (On Continental

Mark III models, pry out the crash

pad insert and remove the two screws

that secure the crash pad. Remove the

crash pad. On models equipped with

steering wheel mounted speed con-

trols,
refer to Group 16 for removal

instructions).

2.
Remove the steering wheel from

the steering shaft with tool T67L-

3600-A (Fig. 1). Then, remove the

tool from the steering wheel. Do not

use a knock-off type steering Wheel

puller or strike the end of the steering

shaft with a hammer. Striking the

puller or shaft will damage the bear-
ing or the collapsible column.

3.
Remove the steering column

from the vehicle.

4.
Remove the selector lever from

the hub (Fig. 16).

5.
Remove the bearing upper snap

ring. It may be necessary to pull the

turn signal switch out to remove the

snap ring.

6. Remove the screws that attach

the shift tube bearing, shift arms, and

shift tube to the lower end of the

steering column.

7.
Slip the shift tube and steering

shaft from the lower end of the steer-

ing column tube. The upper bearing

has a slight press fit on the steering

shaft.

8. Remove the C-washer from the

upper end of the steering shaft, and

pull the shift tube from the steering

shaft.

9. Remove the shift tube bearing

from the lower end of the tube

Installation

1.
Position the shift tube bearing
(Fig. 16) on the tube and insert the

steering shaft in the shift tube.

2.
Install the C-washer on the

upper end of the steering shaft.

3.
Insert the shift tube and steering

shaft into the steerint column tube

and install the three attaching screws

at the lower end of the steering col-

umn tube.

4.
Position the bearing and insula-

tor on the shaft if it was disturbed

during removal. Work it down onto

the shaft as far as possible, then place

a piece of 3/4 ID x 2 1/8 inch pipe

over the end of shaft and install the

steering wheel attaching nut (Fig. 2).

5.
Tighten the nut until the bearing

is seated in the flange, then remove

the nut and pipe from the shaft.

6. Position the turn signal switch

on the flange and install the three at-

taching screws. Install the upper snap

ring.

7.
Install the selector lever and the

turn signal lever in the column.

8. Adjust and install the neutral

start switch as detailed in Group 7.

9. Install the steering column in the

vehicle.procarmanuals.com

03-05-15
Steering Columns And Linkage

03-05-15

SHIFT

TUBE
STEERING

COLUMN
TUBE
SELECTOR

I
LEVER
HUB

\
CENTERING

I
WASHER
QUADRANT

BEARING

UPPER

SNAP RING

TURN SIGNAL AND

EMERGENCY FLASHER

SWITCH

PLASTIC

CONDUIT

STEERING

SHAFT

CONNECTOR

FIG. 16—Typical Stationary Steering Column Disassembled—Standard Transmission
G 1494-A

SNAP RING
STEERING WHEEL-3600

SEAL - 7C102

BEARING -3517

SNAP RING

FLANGE -3511

SELECTOR BEZEL-

LEVER- 7210 ZtL

GEAR SHIFT LEVER

(FIRST
&

REVERSE)
/
7303
/ 9

WASHER - 7242

BUSHING - 733

- 7347

UPPER CLAMP-01698
GEARSHIFT LEVER

(SECOND & THIRD) - 7302

SEAL-

LOWER CLAMP - 01699
^^r**——
FLEX JOINT - 3A525

FIG. 17—Typical Stationary Steering Column Disassembled—Automatic Transmission
G1501-Aprocarmanuals.com

03-05-20
Steering Columns And Linkage

03-05-20

placed if it becomes worn or damaged

(Figs.
18 through 21). Do not attempt

to straighten the sleeve if damaged.

1.
Remove the spindle connecting

rod end assemblies as described in the

previous sub-section.

2.
Screw the spindle rod end assem-

blies into the new sleeve the same

number of turns as the ends that were

removed. Do not tighten the clamp

bolts at this time.

3.
Position the sleeve and end as-

sembly on the center link and the

spindle arm. Install the attaching nut,

torque it to specification, and install

the cotter pin.

4.
Check and, if necessary, adjust

toe-in (Part 3-1). After toe-in is

checked and adjusted, oil the sleeve

clamp bolts then torque them to speci-

fication. The sleeve clamp must be in-

stalled as shown in Figs. 18 through

21.

CENTER LINK

REPLACEMENT

The center link connecting the Pit-

man arm and the idler arm is non-

adjustable and is provided with ta-

pered holes to accommodate the ball

studs (Figs. 18 through 21). The link

should be replaced when damaged or

when worn at the ball studs. On Lin-

coln Continental models, the link

should be replaced if excessive loose-

ness is noticed in either ball stud sock-

et.

REMOVAL

1.
Raise the vehicle on a hoist and

position safety stands.

2.
Remove the cotter pins and nuts

that attach both inner connecting rod

ends to the center link (Figs. 18

through 21).

3.
Disconnect the inner connecting

rod ends from the center link using

Tool 3290-C (Fig. 22).

4.
Remove the cotter pin and nut

attaching the idler arm to the center

link. Disconnect the idler arm from

the center link using Tool 3290-C for

Lincoln Continental models only.

5.
Remove the cotter pin and nut

attaching the Pitman arm to the cen-

ter link. Disconnect the Pitman arm

from the center link (use Tool 3290-C)

and remove the center link. On ve-

hicles equipped with the non-integral

power steering system, remove the

center link from the control valve as

detailed in Part 3-7.

INSTALLATION

1.
Replace the rubber seals on the
spindle connecting rod ends, if re-

quired.

2.
Position the center link to the

Pitman arm and idler arm and install

the attaching nuts loosely. On all ve-

hicles except Lincoln Continental

models, place the idler arm and the

front wheels in the straight ahead po-

sition to insure keeping the steering

wheel aligned and to prevent bushing

damage after the attaching nuts have

been torqued. On Lincoln Continental

models, insure that the seal is properly

installed on the center link. Torque

the nuts to the low end of the specifi-

cation. Continue to tighten each nut

until the slots in the nut align with the

hole in the stud. Then install a new

cotter pin.

3.
Position the spindle connecting

rod ends to the center link and install

the attaching nuts. Torque the nuts to

the low end of the specification. Con-

tinue to tighten each nut until the

slots in the nut align with the hole in

the stud. Then, install a new cotter

pin.

4.
Remove the safety stands, lower

the vehicle, check and adjust toe-in to

specification (Part 3-1).

STEERING IDLER ARM

AND BRACKET ASSEMBLY

REPLACEMENT

REMOVAL

If the idler arm bushings are worn

the complete idler arm assembly must

be replaced. In Lincoln Continental

models, if the socket at the idler

bracket is excessively loose, replace

the complet assembly.

1.
Remove the cotter pin and nut

attaching the steering center link at

the idler arm (Figs. 18 through 21).

2.
Disconnect the center link from

the idler arm (on Lincoln Continental

models, use Tool 3290-C).

3.
Remove the two bolts that attach

the idler arm and bracket assembly to

the frame.

INSTALLATION

1.
Secure the new idler arm and

bracket assembly to the frame with

the two attaching bolts (nuts and flat

washers as shown in Figs. 18, 19 and

21).

2.
On all vehicles except Lincoln

Continental models, place the idler

arm and the front wheels in the

straight ahead position to insure keep-

ing the steering wheel aligned and to
prevent bushing damage after the at-

taching nut has been torqued. Insert

the center link stud through the hole

in the end of the idler arm and install

the nut and washer.

On Lincoln Continental models, in-

sert the center link stud through the

hole in the end of the idler arm insur-

ing that the seal is properly installed

on the center link.

3.
Torque the idler arm rod nut to

specification and install a new cotter

pin.

PITMAN ARM

REPLACEMENT

REMOVAL

1.
Remove the cotter pin from the

castellated nut that attaches the steer-

ing center link to the Pitman arm.

Remove the castellated nut.

2.
Disconnect the steering center

link from the Pitman arm with tool

3290-C.

3.
Remove the Pitman arm attaching

nut and lock washer.

4.
Position the front wheels in the

straight ahead position. Remove the

Pitman arm with tool T64P-3590-F

(Fig. 23).

INSTALLATION

1.
With the front wheels in the

straight ahead position, place the Pit-

man arm on the sector shaft making

sure it is pointing forward.

2.
Install the nut and lock washer.

Torque the nut to specification.

G1663-A

FIG. 23— Removing Pitman

Arm—Typicalprocarmanuals.com

03-06-02
Manual Steering

03-06-02

IN-VEHICLE ADJUSTMENTS AND REPAIRS

STEERING WORM AND

SECTOR

GEAR ADJUSTMENTS

The ball nut assembly and the sec-

tor gear must be adjusted properly to

maintain minimum steering shaft end

play (a factor of preload adjustment)

and minimum backlash between sector

gear and ball nut. There are only two

possible adjustments within the recir-

culating ball-type steering gear, and

these should be made in the following

order to avoid damage or gear failure.

1.
Disconnect the Pitman arm from

the steering Pitman-to-idler arm rod.

2.
Loosen the nut which locks the

sector adjusting screw (Fig. 3), and

turn the adjusting screw counterclock-

wise.
(On models equipped with the

Cobra Jet engine, it may be necessary

to use a suitable holding tool with an

extension and a long screwdriver to

make the gear adjustment).

3.
Measure the worm bearing pre-

load by attaching an in-lb torque

wrench to the steering wheel nut (Fig.

4).
With the steering wheel off center,

read the pull required to rotate the

input shaft approximately 1 1/2 turns

either side of center. If the torque or

preload is not within specification

(Part 3-1), adjust as explained in the

next step.
.•ADJUSTER
LOCK
NUT

SECTOR
SHAFT

ADJUSTING
SCREW
G
1627-A

FIG. 3—Steering Gear

Adjustments—Typical

4.
Loosen the steering shaft bearing

adjuster lock nut, and tighten or back

off the bearing adjuster (Fig. 1) to

bring the preload within the specified

limits.

5.
Tighten the steering shaft bear-

ing adjuster lock nut, and recheck the

preload.

6. Turn the steering wheel slowly to

either stop. Turn gently against the

stop to avoid possible damage to the

ball return guides. Then rotate the

wheel 2-3/4 turns to center the ball

nut.
7.
Turn the sector adjusting screw

clockwise until the specified torque

(Part 3-13) is necessary to rotate the

worm past its center (high spot) (Fig.

1).

8. While holding the sector adjust-

ing screw, tighten the sector adjusting

screw locknut to specification, and re-

check the backlash adjustment.

9. Connect the Pitman arm to the

steering arm-to-idler arm rod.

G-1495-A

FIG. 4—Checking Steering Gear

Preload—Typical

REMOVAL AND INSTALLATION

STEERING GEAR

REMOVAL

1.
Remove the bolt(s) that retains

the flex coupling to the steering shaft.

2.
Remove the nut and lock washer

that secures the Pitman arm to the

sector shaft using Tool T64P-3590-F

(Fig. 5).

3.
To obtain clearance on some

models equipped with standard trans-

mission, it may be necessary to dis-

connect the clutch linkage. On some

8-cylinder models, it may be necessary

to lower the exhaust system.

4.
Remove the steering gear-to-side

rail bolts and remove the gear.
Too /-MB
STEERING
GEAR
HOUSING

T64P-3590.F

(PITMAN
"APU'^M
-
.-. •
-"
•.:,.17''i.a—
r.iMI.
A

F'G.
5—Removing Pitman Arm
INSTALLATION

1.
Position the steering gear and

flex coupling in place; then, install

and torque the steering gear-to-side

rail bolts to specification (Part 3-13).

2.
If the clutch linkage has been

disconnected, reposition, install and

adjust it. If the exhaust system has

been lowered, reinstall it to its proper

position.

3.
Position the Pitman arm and the

sector shaft and install the attaching

nut and lock washer. Torque the nut

to specification.

4.
Install and connect the flex cou-

pling attaching nut(s) and torque it to

specification (Part 3-13).procarmanuals.com

03-07-02
Ford Design Non-Integral Power Steering System

03-07-02

PUMP AND RESERVOIR

CONTROL VALVE

POWER CYLINDER

FIG. 7—Non-Integral Power Steering System
G 1651-A

IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

HOISTING INSTRUCTIONS

Damage
to
suspension and/or steer-

ing linkage components
may
occur
if

care
is not
exercised when positioning

the hoist adapters
of 2
post hoists

prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

front suspension lower arms.
Do not

allow
the
adapters
to
contact
the

steering linkage.

CONTROL VALVE CENTERING

SPRING ADJUSTMENT

1.
Raise
the
vehicle
and
remove
2

spring
cap
attaching screws
and
lock

washers
and
remove
the
spring
cap.

2.
Tighten
the
adjusting
nut
snug

(90-100 in-lbs); then, loosen
the nut

1/4 turn. Make sure that
the nut ro-

tates
1/4
turn
(90
degrees)
on the

threads
of the
bolt.
Do not
tighten
the

adjusting
nut too
tight.

3.
Position
the
spring
cap to the

valve housing. Lubricate
and
install

the
two
attaching screws
and
washers.

Torque
the
screws
to
72-100 in-lbs.

4.
Lower
the
vehicle.

5.
Start
the
engine
and
check
the

turning effort with
a
spring scale.

With
the
spring scale attached
to the

rim
of the
steering wheel,
the
effort
to
turn
the
wheel
in
both directions

should
not
exceed
12
pounds.

CONTROL VALVE
TO
POWER

STEERING CYLINDER HOSE

1.
Raise
the
vehicle
on a
hoist
and

place
a
drain
pan
under
the
power

cylinder.

2.
Disconnect
the
hose from
the

power cylinder
and
allow
the
fluid
to

drain from
the
hose. Then, disconnect

the hose from
the
control valve.

3.
Connect
the
unmarked
end of

the shorter tube
(9 7/16 in
long)
to

valve port
C
(Fig. 2). Hold
the
tube
so

that
the
bend parallels
the
surface
of

valve shown
in Fig. 2,
tighten
the nut.

PLANE
OF
TUBE BEND
IN

3A717 HOSE
TO BE
PARALLEL

WITH THIS SURFACE ON VALVE.

CLEARANCE BETWEEN

COUPLING TO
BE 1/16-

1/8 INCH
IN
THIS AREA

G 1503-A

FIG. 2—Power Steering Hose

Installation
Connect
the
opposite
end to the
lower

port
in the
cylinder. Hold
the
tube
se-

curely while tightening
the nut to pre-

vent twisting
the
tube. Connect
the

other tube
(9 5/8 in
long)
to
port
A,

making sure that tube
is
parallel with

the other tube.

4.
Remove
the
drain
pan and
lower

the vehicle.

5.
Fill
the
power steering pump res-

ervoir with fluid
to the
proper level

(Part
3-1).

6. Start
the
engine
and
turn
the

steering wheel
to
each
end of its
travel

several times
to
cycle
the
system.

Then, check
for
leaks.

7.
Stop
the
engine
and
again check

the power steering fluid level.
Add

fluid
as
required.

POWER STEERING PUMP

TO CONTROL VALVE HOSE

REMOVAL

1.
Remove
the
fluid from
the
pump

reservoir with
a
suction
gun.

2.
Raise
the
vehicle
on a
hoist.

3.
Remove
the
clamp retaining
the

hose tubes
to the
control valve.

4.
Disconnect
the
fluid return
and

pressure hoses from
the
control valve

and allow
the
fluid
to
drain into
a

pan.procarmanuals.com

03-07-03
Ford Design Non-Integral Power Steering System

03-07-03

5.
Lower the vehicle and disconnect

the fluid return hose from the reser-

voir.

6. Disconnect the fluid pressure

hose from the pump outlet fitting.

7.
Remove 1 bolt attaching the

hoses,
insulator, and the retainer to

the frame side rail and remove the

hoses,
and the insulator and retainer

as an assembly from the vehicle.

8. Remove the pressure and return

hoses from the retainer and insulator.

INSTALLATION

1.
Install the pressure and return
hoses in the insulator and retainer.

Paint stripe on pressure hose must be

aligned with slot in insulator. Paint or

tape band on return hose must be cen-

tered in insulator. Position the assem-

bly to the frame side rail and install

the attaching bolt.

2.
Place a hose clamp on the fluid

return hose and install the hose on the

power steering pump reservoir return

fitting.

3.
Torque the pump outlet fitting to

specification (Part 3-13). Then, con-

nect the pressure hose to the outlet fit-

ting and torque the fitting to specifica-

tion.
4.
Raise the vehicle and connect the

pressure and return lines to the con-

trol valve.

5.
Install the clamp to retain the

hose tubes to the control valve.

6. Lower the vehicle and fill the

power steering pump reservoir with

fluid, C1AZ-19582-A, to the proper

level (Part 3-1).

7.
Start the engine and turn the

steering wheel to each end of its travel

several times to cycle the system.

Then, check for fluid leaks.

8. Stop the engine and again check

the power steering fluid level (Part

3-1). Add fluid as required.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to suspension and/or steer-

ing linkage components may occur if

care is not exercised when positioning

the hoist adapters of 2 post hoists

prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

front suspension lower arms. Do not

allow the adapters to contact the

steering linkage.

STEERING GEAR

Refer to Group 3-6, Section 3 for

detailed instructions.

POWER STEERING PUMP

Refer to Group 3-10, Section 3 for

detailed instructions.

POWER STEERING CONTROL

VALVE

REMOVAL

1.
Disconnect the 4 fluid line fit-

tings at the control valve, and drain

the fluid from the lines. Turn the front

wheels to the left and right several

times to force all the fluid from the

system.

2.
Loosen the clamping nut and

bolt at the right end of the sleeve.

3.
Remove the roll pin from the

steering arm-to-idler arm rod -through

the slot in the sleeve.

4.
Remove the control valve ball

stud nut.

5.
Using the tool shown in Fig. 3,

remove the ball stud from the sector

shaft arm.
VALVE

Too/-3290-C BALL STUD PITMAN ARM

FIG. 3—Removing Control Valve

Ball Stud

6. After turning the front wheels

fully to the left, unthread the control

valve from the center link steering

arm-to-idler arm rod.

INSTALLATION

1.
Thread the valve onto the center

link until about four threads are still

visible on the link.

2.
Position the ball stud in the sec-

tor shaft arm.

3.
Measure the distance between

the center of the grease plug in the

sleeve and the center of the stud at the

inner end of the left spindle connect-

ing rod (Fig. 4). The distance should

be 5 5/8 inches for Montego, Falcon

and Fairlane vehicles. The distance

should be 4 7/8 inches for Mustang

and Cougar models. If the distance is

not correct, disconnect the ball stud

from the sector shaft arm and turn the

valve on the center link to increase or

decrease the distance.

4.
When the correct distance is ob-

tained and the ball stud is positioned

in the sector shaft arm, align the hole

in the steering arm-to-idler arm rod

with the slot near the end of the valve
sleeve. Install the roll pin in the rod

hole to lock the valve in position on

the rod.

5.
Torque the valve sleeve clamp

bolt to specification.

6. Install the nut on the ball stud,

and torque the nut to specification.

Install a new cotter pin.

7.
Connect the fluid lines to the

control valve, and tighten all fittings

securely. Do not over-tighten.

8. Fill the fluid reservoir with the

specified fluid to the cross hatched

area on the dip stick.

9. Start the engine and run it at

idle speed for about two minutes to

warm the fluid in the power steering

system.

10.
Turn the steering wheel all the

way to the left and right several times,

and check the system for fluid leaks.

11.
Increase the engine speed to

about 1000 rpm, and turn the steering

wheel all the way to the left and right

several times.

CONTROL VALVE CONNECTING ROD STUD

LUBRICATION PLUG

G1653-A

FIG. 4—Control Valve Installation

Measurements—All Modelsprocarmanuals.com