1969 FORD MUSTANG lock

03-10-03
Ford-Thompson Power Steering Pump

03-10-03

EIGHT CYLINDER WITH

AIR CONDITIONER

1.
Remove the power steering fluid

from the pump reservoir by discon-

necting the fluid return hose from the

reservoir and allow the fluid to drain

in a suitable container.

2.
Disconnect the pressure hose

from the pump.

3.
Remove 3 bolts from the front of

the pump and the one nut at the rear

that attach the pump to the mounting

bracket and remove the drive belt

from the pump pulley.

4.
Loosen the upper pump bracket-

to-engine attaching bolt and remove

the bolt in the belt adjusting slot. Re-

move the pump.

5.
Position the pump to the bracket

and install the bracket-to-pump at-

taching bolts and nuts. Tighten to spe-

cifications.

6. Place the belt on the pump pul-

ley. Adjust the belt tension as outlined

in Section 2 and tighten the bolts and

nut to specification.

7.
Torque the pressure hose fitting

hex nut to specification. Then, connect

the pressure hose to the fitting and

torque the hose nut to specification.

8. Connect the return hose to the

power steering pump and tighten the

clamp.

9. Fill the pump with automatic

transmission fluid C1AZ-19582-A.

Bleed the air from the system (Part

3-1) and check for leaks and again
check the fluid level. Add fluid as re-

quired.

POWER STEERING PUMP

PULLEY REPLACEMENT

REMOVAL

1.
Drain as much of the fluid as

possible from the pump through filler

pipe.

2.
Install a 3/8-16 inch capscrew in

the end of the pump shaft to prevent

damage to the shaft end by the tool

screw.

3.
Install the pulley remover, Tool

T63L-1O3OO-B, on pulley hub, and

place the tool and pump in a vise as

shown in Fig. 3.

4.
Hold the pump and rotate the

tool nut counterclockwise to remove

the pulley (Fig. 3). The pulley must be

removed without in and out pressure

on the pump shaft to prevent damage

to internal thrust areas.

INSTALLATION

1.
Position the pulley to the pump

shaft and install Tool T65P-3A733-A

as shown in Fig. 4.

2.
Hold the pump and rotate the

tool nut clockwise to install the pulley

on the shaft. The pulley face will be

flush with end of pump shaft. Install

the pulley without in and out pressure
on the shaft to prevent damage to in-

ternal thrust areas.

3.
Remove the tool.

POWER STEERING PUMP

RESERVOIR REPLACEMENT

Reservoir replacement must be done

on a clean workbench. Cleanliness of

work area and tools is extremely im-

portant when repairing any hydraulic

unit. Thoroughly clean the exterior of

the pump with a suitable cleaning sol-

vent. Do not clean, wash or soak the

shaft oil seal in solvent. Plug the inlet

and outlet openings with plugs or

masking tape before cleaning the

pump exterior or removing the reser-

voir.

REMOVAL

1.
Assemble the adapter plate (Tool

T69P-3A674-A) to the bench mounted

fixture tool (T57L-5OO-A). Position

the pump and pulley on the adapter

plate, pulley facing down.

2.
Remove the outlet fitting hex nut

and the service identification tag.

3.
Invert the pump so the pulley is

facing up and remove the reservoir by

tapping around the flange with a wood

block (Fig. 5).

4.
Remove the reservoir O-ring seal

and the outlet fitting gasket from the

pump.

INSTALLATION

Tool • T 63 L-

10300 -

G 1477 A

FIG. 3—Removing Power

Steering Pump Pulley
1478 A

FIG. 4—Installing Power

Steering Pump Pulley
1.
Install a new gasket on the outlet

fitting and a new reservoir O-ring seal

on the pump housing plate (Fig. 6).

The old gasket and seal should never

be re-used.

Too/
T57L 500-A

G1602-A

FIG. 5—Removing Pump

Reservoirprocarmanuals.com

03-10-04
Ford-Thompson Power Steering Pump

03-10-04

OUTLET FITTING

GASKET
Wood Block

0-RING SEAL

G1345-
-500-
A

G1603- A

FIG. 6—Gasket Locations
FIG.
7—Installing
Reservoir

on Pump—Typical
2.
Apply vaseline to the reservoir

O-ring seal and to the inside edge of

the new reservoir flange. Do not twist

the O-ring seal.

3.
Position the reservoir over the

pump and align the notch in the reser-

voir flange with the notch in the outer

diameter of the plate and bushing as-

sembly.

4.
Install the reservoir on the pump

and O-ring seal with a plastic or rub-

ber hammer and a block of wood as

shown in Fig. 7. Tap at the rear of the

reservoir and on the outer edges only.

5.
Inspect the assembly to be sure

the reservoir is evenly seated on the

pump housing plate.

6. Position the service identification

tag on the outlet fitting and install the

outlet fitting hex nut. Torque the nut

to specification (Part 3-13). Do not

exceed specification.

MAJOR REPAIR OPERATIONS

DISASSEMBLY

Disassembly of the pump and its

subassemblies must be made on a

clean work bench. In repairing any

hydraulically operated unit, cleanliness

is of utmost importance. Clean the ex-

terior of the unit with a suitable sol-

vent and drain as much of the fluid as

possible.

If only the reservoir is to be re-

moved, plug the inlet and outlet open-

ings with masking tape or plugs. Do

not immerse the shaft oil seal in sol-

vent. If only the rotor shaft seal is to

be replace, see Rotor Shaft Seal Re-

placement outlined in this section.

1.
Assemble the adapter plate (Tool

T69P-3A674-A) to the bench mount-

ed holding fixture Tool T57L-5OO-A

(Fig. 8).

2.
Position the pump assembly,

with pulley assembled, on the adapter

plate, pulley facing down.

3.
Remove the outlet fitting nut and

the service identification tag.

4.
Invert the pump assembly and,

using a block of wood and a rubber or

plastic hammer, remove the pump res-

ervoir and seal by tapping around the

flange of the reservoir and on the und-

erside of the filler neck.

5.
Again invert the pump assembly,

loosen and remove the pump housing

retention bolts and remove the pump

housing.
6. If necessary, remove the fol-

lowing components from the pump

housing: the housing cover, the O-ring

seal and the pressure springs. These

components normally will remain in

the pump housing when it is removed.

7.
Remove and discard the pump

cover gasket.

8. Remove the retainer end plate

and upper pressure plate (in some

pumps, the end plate and upper pres-

sure plate are integral).

9. Remove the loose fitting dowel

pin. Be careful not to bend the fixed

dowel pin which remains in the hous-

ing plate assembly.

10.
Remove the rotor assembly

being careful to prevent the springs

and slippers from falling out and be-

coming lost. Do not disassemble fur-

ther unless the lower pressure plate,

housing plate, rotor shaft and/or seal

is to be replaced.

11.
Invert the pump assembly and,

using Tool T63L-1O3OO-B, remove the

pulley.

12.
Clean any rust, road dirt, burrs,

scoring, etc. from the pulley end of

the rotor shaft prior to removal of the

shaft from the housing plate. The

shaft must come out without restric-

tions to prevent scoring or damage to

the bushing. Remove the pump rotor

shaft.

13.
Remove the lower pressure

plate.
PARTS REPAIR OR

REPLACEMENT

ROTOR SHAFT

SEAL REPLACEMENT

Removal

1.
Remove the pulley from the

rotor shaft as described under Power

Steering Pump Pulley Removal.

2.
Position the pump assembly in

T57L-500-A

T69P-3A674-A

•
G1604-A

FIG. 8—Adapter Plate Installationprocarmanuals.com

03-11-02
Eaton Power Steering Pump

03-11-02

gasket. Withdraw the fluid with a suc-

tion gun.

2.
Remove the reservoir bracket-

to-cylinder block upper cap screw and

the lower cap screw and spacer.

3.
Disconnect the reservoir infet line

and the outlet line at the reservoir,

and remove the reservoir.

Installation

1.
Connect the reservoir-to-pump

line (outlet line) at the reservoir, but

do not tighten the clamp.

2.
Attach the reservoir and bracket

to the cylinder block with the upper

cap screw and the lower cap screw

and spacer. Tighten the cap screws.

3.
Tighten the outlet line clamp at

the reservoir. Connect the reservoir

inlet line to the reservoir.

4.
Fill the reservoir with the speci-

fied automatic transmission fluid. Run

the engine, and bleed the system by

cycling the steering gear with the

windshield wipers turned on. Check

for leaks, and recheck the fluid level.
WITH AIR CONDITIONING

Removal

1. Raise the front of the vehicle.

Remove the reservoir-to-pump line

(outlet line) clamp at the reservoir,

but do not disconnect the line at this

time.

2.
Disconnect the reservoir inlet line

at the reservoir.

3.
Remove the reservoir bracket to

the cylinder block upper cap screw.

Support the reservoir and remove the

lower cap screw and spacer.

4.
With a drain pan under the res-

ervoir, disconnect the outlet line hose

from the reservoir tube and allow the

fluid to drain.

5.
Remove the reservoir cover re-

taining nut and the cover. Position the

cover and the reservoir out of the way

and allow them to rest in the engine

compartment.

6. Lower the front of the vehicle.

Remove the fan shroud.

7.
Remove the reservoir and the
cover by manipulating them through

the opening between the radiator and

the compressor drive belt.

Installation

1.
Position the reservoir in the en-

gine compartment. Loosely attach the

reservoir and bracket to the cylinder

block with the upper cap screw.

2.
Install the fan shroud, then raise

the front of the vehicle.

3.
Connect the reservoir-to-pump

line (outlet line) at the reservoir.

4.
Install the reservoir bracket-

to-cylinder block lower cap screw and

spacer. Tighten both the upper and

the lower cap screws.

5.
Connect the reservoir inlet line at

the reservoir. Install the clamps on

both lines. Lower the car, and install

the reservoir cover and attaching nut.

6. Fill the reservoir with the speci-

fied automatic transmission fluid. Run

the engine, and bleed the system by

cycling the steering gear with the

windshield wipers turned on. Check

for leaks, and recheck the fluid level.

3 MAJOR REPAIR OPERATIONS

INSULATOR (2)

WASHER (2)

MOUNTING BOLT (2)

COVER

BOLT (7)
DOWEL
PIN (2)

ROTOR

ROTOR
SHAFT

COVER
SEAL
PLUG

O RING

VALVE
ASSEMBLY

VALVE
SPRING

INSULATOR

HOUSING

CAM RING

PRESSURE
PLATE
,
PUMP

i
HOUSING

SEAL

ROLL

PIN

INSULATOR

RETAINER
RING
TUBE SEAT

O RING

SCREW
(2)

G12O8-B

FIG.
1
— Power Steering Pumpprocarmanuals.com

03-11-03

Eaton Power Steering Pump

03-11-03

POWER STEERING PUMP

DISASSEMBLY

A clean working area should be

used when overhauling the power

steering pump. Foreign matter picked

up on working parts may cause dam-

age or failure of the unit. Clean con-

tainers should be used for parts.

1.
Drain the fluid from the pump.

Remove the pump cover-to-housing

cap screws (Fig. 1). Place the pump

on the bench, cover side down. Lift

the housing from the cover.

2.
Remove the large and the small

O-rings from the pump cover. Remove

the O-ring from the pressure plate

hub.

3.
Remove the pressure plate-

to-cover screws, and remove the plate.

Lift the cam ring off the dowel pins.

4.
Remove the rollers. Lift the

rotor off the shaft, and remove the

drive key from the shaft. Remove the

dowel pins from the cover.

5.
Remove the rotor shaft from the

cover. Do not remove the snap ring

from the shaft unless it, or the shaft,

is damaged.

6. Pry the rotor shaft seals out of

the cover and the housing.

7. Do not disturb the control valve

unless diagnosis indicated a control

valve problem or foreign matter in the

valve. To remove the valve, drive the

roll pin out of the housing. Remove

the plug and O-ring, control valve,

and the spring. If the plug or valve is

stuck, tap the end of the housing on a

piece of wood or tap it with a soft-

faced hammer. Remove the O-ring

from the plug.

ASSEMBLY

Apply automatic transmission fluid

to all parts as they are assembled. Al-

ways use new seals and O-rings.

1.
Install the control valve spring in

the housing. Install the valve with the

small sensing hole in the end of the

valve toward the spring. Install a new

O-ring on the plug. The plug O-ring is

1/8 inch smaller in diameter than the

bypass O-ring. Make sure the proper

O-ring is used. Install the plug and a

new roll pin (Fig. 1).

2.
The rotor shaft oil seals are in-

stalled in the cover and the housing

with Tool 3583-J, which consists of a

driver and an adapter. The procedure

is as follows:

a. Support the cover on wood

blocks (Fig. 2) to provide tool clear-

ance.
Use clean blocks that will not

nick or damage the inner face of the

cover.
b.
Start the seal (metal shell up-

ward) square!y into the bore with fin-

ger pressure. Place the adapter on the

driver with the square corner of the

FIG. 2—Preparation for Installing

Rotor Shaft Seals

adapter toward the seal (Fig. 2). Drive

the seal into the cover, as shown in

Fig. 3, until it bottoms.

Driving the seal beyond this point

can damage it. Install the seal in the

pump housing in the same manner.

3.
Install the rotor shaft in the

FIG. 3—Installing Rotor

Shaft Seals
cover as shown in Fig. 4 to prevent

damage to the seal.

4.
Install the dowel pins in the

cover. Place the rotor drive key in the

shaft. Install the rotor on the shaft

with the drive key groove aligned with

the key and the counterbored side of

the rotor toward the cover so that it

goes over the snap ring.

5.
Place the cam ring on the dowel

pins with the chamfered edge upward

(Fig. 5). Place the rollers in the rotor.

6. Place the pressure plate on the

dowel pins. Install and tighten the

screws to 20 in-lbs torque. Install the

O-ring on the pressure plate hub. In-

stall O-rings in the groove at the fluid

bypass hole and around the cam ring

(Fig. 6).

7.
Place the tool shown in Fig. 6 in

the rotor shaft to prevent damage to

the oil seal, then install the housing on

the cover. Install and torque the cap

screws to 15-20 ft-lbs.

FIG. 5—Cam Ring Installation

FIG. 4—Installing Rotor Shaft

in Cover

FIG. 6—O-Ring Installationprocarmanuals.com

03-12-01

Wheels
And
Tires

03-12-01

PART
3-12
Wheels
And
Tires

COMPONENT INDEX

FRONT
HUB AND
DRUM ASSEMBLY

Removal
and
Installation

FRONT
HUB AND
ROTOR ASSEMBLY

Removal
and
Installation

FRONT WHEEL ASSEMBLY DESCRIPTION

FRONT WHEEL BEARING ADJUSTMENT

FRONT WHEEL GREASE SEAL
AND

BEARING

Removal, Installation, Repacking

HOISTING INSTRUCTIONS

LIFE GUARD TIRE

Balancing

Correcting Vibration
and
Shake

Description

Repairs

REAR WHEEL ASSEMBLY DESCRIPTION

WHEELS AND TIRES (Conventional)

Removal
and
Installation
MODEL APPLICATION
All
Models

12-07

12-07

12-01

12-02

12-05

12-02

12-01

12-03
Ford
N/A

N/A

N/A

N/A
Mercury
N/A

N/A

N/A

N/A
Meteor
N/A

N/A

N/A

N/A
Cougar
N/A

N/A

N/A

N/A
Fairlane
N/A

N/A

N/A

N/A
Falcon
N/A

N/A

N/A

N/A
Montego
N/A

N/A

N/A

N/A
Mustang
N/A

N/A

N/A

N/A
Lincoln-
Continental
12-03

12-03

12-02

12-08
Thunderbird
12-03

12-03

12-02

12-08
Continental-
Mark
III
12-03

12-03

12-02

12-08

A page number indicates that
the
item
is for the
vehicle listed
at the
head
of the
column.

N/A indicates that
the
item
is not
applicable
to the
vehicle listed.

DESCRIPTION

FRONT WHEEL ASSEMBLY

Each front wheel
and
tire
is
bolted

to
its
respective front
hub and
brake

drum
or
rotor assembly.
Two
opposed

tapered roller bearings
are
installed
in

each
hub. A
grease retainer
is in-

stalled
at the
inner
end of the hub to

prevent lubricant from leaking into

the drum
or on the
rotor.
The
entire

assembly
is
retained
to its
spindle
by

the adjusting
nut, nut
lock
and
cotter

pin (Figs.
1 and 2).

REAR WHEEL ASSEMBLY

The rear wheel
hub and
brake drum

assembly
is
attached
to
studs
on the

rear axle shaft flange
by
three speed

nuts.
The
wheel
and
tire mounts
on

the same rear axle shaft flange studs

and
is
held against
the hub and
drum

by
the
wheel nuts.
The
rear wheel

bearing
is
pressed onto
the
axle shaft

just inside
the
shaft flange,
and the
entire assembly
is
retained
to the
rear

axle housing
by the
bearing retainer

HUB
AND
BRAKE

DRUM
ASSEMBLY
plate which
is
bolted
to the
housing

flange.

ADJUSTING

NUT

GREASE

CAP
OUTER

BEARING

OUTER
CUP

BEARING

CONE
AND

ROLLER

NUT
INNER BEARING

CONE
AND

ROLLER

WHEEL

ASSEMBLY

HUB
BOLT'
^£=3^
F1422-A

FIG.
1
—
Front
Hub,
Bearing
and
Grease Retainer Drum Brakes
procarmanuals.com

03-12-02
Wheels
And
Tires

03-12-02

LIFE GUARD TIRE

The Goodyear Power Cushion Tire

(available
on
Thunderbird, Lincoln

and Continental Mark
III
models)
fit-

ted with
the
Life Guard Safety Spare
provides
a
tire within
a
tire with
two

separate
air
chambers
(Fig.
3). If the

outer tire casing should
be
punctured

or otherwise damaged causing
it to go

flat,
the
Life Guard Safety Spare will

carry
the
load
of the
vehicle
and
will
allow driving
at
speeds
up to 40 mph

with good control
up to a
distance
of

40 miles.
A
Safety-Signal built into

the Life Guard tread produces
a
lope

or vibration indicating
the
outer tire

has lost pressure.

HUB AND ROTOR

ASSEMBLY
INNER

BEARING

CUP
GREASE

RETAINER

ADJUSTING

NUT

OUTER

BEARING

CONE
AND

ROLLER

INNER BEARING

CONE
AND

ROLLER

WHEEL

ASSEMBLY

F1416-A

F- 1380 •
A

FIG. 2—Front
Hub and
Rotor Bearing
and
Grease

Retainer Disc Brakes—Typical
FIG. 3—Life Guard Safety

Tire—Sectional View

IN-VEHICLE ADJUSTMENTS AND REPAIRS

HOISTING INSTRUCTIONS

Damage
to
steering linkage compo-

nents
and
front suspension struts
may

occur
if
care
is
not
exercised when
po-

sitioning
the
hoist adapters
of 2
post

hoists prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

lower arms
or
the No. 1
crossmember.

Do
not
allow
the
adapters
to
contact

steering linkage.
If the
adapters
are

placed under
the
crossmember,
a
piece

of wood (2x4x16 inches) should
be

placed
on the
hoist channel between

the adapters. This will prevent
the

adapters from damaging
the
front
sus-

pension struts.

FRONT WHEEL BEARING

ADJUSTMENT

The front wheel bearings should
be

adjusted
if the
wheel
is
loose
on the

spindle
or if the
wheel does
not
rotate

freely.
The
following procedures will

bring
the
bearing adjustment
to
speci-

fication.

DRUM BRAKES

1.
Raise
the
vehicle until
the
wheel

and tire clear
the
floor.
2.
Pry off the hub cap or
wheel

cover
and
remove
the
grease
cap (Fig.

1) from
the hu6.

3.
Wipe
the
excess grease from
the

end
of the
spindle,
and
remove
the

cotter
pin and nut
lock.

4.
While rotating
the
wheel,
hub,

and drum assembly, torque
the
adjust-

ing
nut to 17-25
ft-lbs
to
seat
the

bearings
(Fig.
4).

5.
Locate
the nut
lock
on the ad-

justing
nut so
that
the
castellations
on

the lock
are
aligned with
the
cotter

pin hole
in the
spindle.

6. Using
a 1
1/8-inch
box
wrench,

WITH WHEEL ROTATING

TORQUE ADJUSTING
NUT

TO 17-25 FT. LBS.
BACK ADJUSTING

NUT
OFF
1/2
TURN
back
off the
adjusting
nut one
half

turn. Retighten
the
adjusting
nut to

10-15 in-lbs with
a
torque wrench
or

finger tight.

7.
Position
the
lock
on the
adjust-

ing
nut and
install
a new
cotter
pin.

Bend
the
ends
of
the
cotter
pin
around

the castellated flange
of the nut
lock.

8. Check
the
front wheel rotation.

If
the
wheel rotates properly, install

the grease
cap and the hub cap or

wheel cover.
If the
wheel still rotates

roughly
or
noisily, clean, inspect
or

replace
the
bearings
and
cups
as re-

quired.

TIGHTEN ADJUSTING

NUT
TO
10-15 IN.-LBS.
INSTALL THE LOCK

AND
A
NEW COTTER
PIN

F1417-A

FIG. 4— Front Wheel Bearing Adjustmentprocarmanuals.com

03-12-03

Wheels And Tires

03-12-03

DISC BRAKES

1.
Raise the vehicle until the wheel

and tire clear the floor.

2.
Pry off the wheel cover and re-

move the grease cap (Fig. 2) from the

hub.

3.
Wipe the excess grease from the

end of the spindle, and remove the ad-

justing nut cotter pin and nut lock.

4.
Loosen the bearing adjusting nut

three turns. Then, rock the wheel,

hub,
and rotor assembly in and out

several times to push the shoe and lin-

ings away from the rotor.

5.
While rotating the wheel, hub,

and rotor assembly, torque the adjust-

ing nut to 17-25 ft-lbs to seat the

bearings (Fig. 4).

6. Back the adjusting nut off one

half turn. Then, retighten the adjust-

ing nut to 10-15 in-lbs with a torque

wrench or finger tight.

7.
Locate the nut lock on the ad-

justing nut so that the castellations on

the lock are aligned with the cotter

pin hole in the spindle.

8. Install a new cotter pin, and

bend the ends of the cotter pin around

the castellated flange of the nut lock.

9. Check the front wheel rotation.

If the wheel rotates properly, install

the grease cap and the hub cap or

wheel cover. If the wheel still rotates

roughly or noisily, clean or replace the

bearings and cups as required.

10.
Before driving the vehicle,
pump the brake pedal several times to

obtain normal brake lining to rotor

clearance and restore normal brake

pedal travel.

BALANCING LIFE

GUARD TIRE

Tires fitted with the Life Guard

Safety Spare are balanced in the same

manner as conventional tires. If an ex-

cessive out of balance condition exists

the following procedure can be used to

correct the condition:

1.
Remove the core housing and de-

flate both air chambers.

2.
Install the core housing.

3.
Unseat the beads of tire with the

bead breakers away from the valve

stem as shown in Fig. 5.

F 1383

FIG. 5—Breaking Top Bead of

Tire From Wheel Rim
4.
Rotate tire casing 90 degrees on

the wheel rim.

5.
Rotate the tire casing back and

forth on the rim to center the valve.

6. Inflate both chambers of the tire

following steps 13 through 15 of the

Tire Installation procedure.

7.
Balance the tire in the normal

manner.

CORRECTING VIBRATION

AND SHAKE-

LIFE GUARD TIRE

The condition of excessive vibration

and shake is generally the result of an

incorrect pressure relationship between

the inner and outer air chambers that

may cause the life guard to shift posi-

tion within the tire. The following

procedure should be used to correct

vibration and shake conditions:

1.
Check pressure of the inner and

outer air chambers on all four tires.

2.
If the inner chamber has at least

five psi more pressure than the outer

chamber the pressures should be ad-

justed and the tires rebalanced if nec-

essary.

3.
If the pressures of the inner and

outer air chambers are equal the Air

Container is leaking. To repair the

leaking air container the recommend-

ed procedures for the removal, repair

of air container, mounting, and bal-

ancing should be followed.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to steering linkage compo-

nents and front suspension struts may

occur if care is not exercised when po-

sitioning the hoist adapters of 2 post

hoists prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

lower arms or the No. 1 crossmember.

Do not allow the adapters to contact

the steering linkage. If the adapters

are placed under the crossmember, a

piece of wood (2x4x16 inches) should

be placed on the hoist channel be-

tween the adapters. This will prevent

the adapters from damaging the front

suspension struts.

WHEELS AND TIRES

WHEEL AND TIRE

REMOVAL

1.
Pry off the wheel hub cap or
wheel cover. Loosen but do not re-

move the wheel hub nuts.

2.
Raise the vehicle until the

wheel and tire clear the floor.

3.
Remove the wheel hub nuts

from the bolts, and pull the wheel

and tire from hub and drum.

F1424-
A

FIG.
6—Bead
Loosening Tool
REMOVING CONVENTIONAL

TIRE FROM WHEEL

The tire can be demounted on a

mounting machine. Be sure that the

outer side of the wheel is positioned

downward. If tire irons are used, fol-

low the procedure given here.

1.
Remove the valve cap and core,

and deflate the tire completely.

2.
With a bead loosening tool,

break loose the tire side walls from

the wheel (Fig. 6).

3.
Position the outer side of the

wheel downward, and insert two tire

irons about eight inches apart between

the tire inner bead and the back side

of the wheel rim. Use only tire irons

with rounded edges or irons designed

for removing tubeless tires.

4.
Leave one tire iron in position,

and pry the rest of the bead over the

rim with the other iron. Take small

bites with the iron around the tire inprocarmanuals.com

03-12-05
Wheels
And
Tires

03-12-05

and sharp edges from valve hole
in

rim.

8. Mount first tire bead exercising

care
not to
pinch
air
container.

9. Start valve through hole
in rim.

Do
not
pull valve housing into place

at this time.

10.
Mount
the
second bead starting

just past
the
valve
so the
last portion

of
the
bead goes over
the rim at the

valve.

11.
Rotate
the
tire back
and
forth

to center
the
valve housing.

12.
Pull
the
valve housing into

place. Make certain that
the
rubber

valve ridge
is
visible around
thi
valve

housing
(Fig.
12).

13.
Tighten
the
core housing lightly

using pliers.

14.
Thread
the
Inflate-Chek adapt-

er onto
the
core housing.
15.
Inflate
the
inner chamber
to

seat
the
tire beads exercising care
not

to exceed
45 psi
pressure. Adjust this

inner chamber
air
pressure
to 15 psi

higher than
the
recommended tire

pressure.

F 1387
- A

FIG. 12—Valve Installation
16.
Remove
the
Inflate-Chek

adapter
and
adjust tire (outer cham-

ber) pressure
to the
recommended

pressure.

17.
Recheck inner chamber pres-

sure.

18.
Install valve
cap.

WHEEL
AND
TIRE

INSTALLATION

1.
Clean
all
dirt from
the hub and

drum.

2.
Position
the
wheel
and
tire
on

the
hub and
drum. Install
the
wheel

hub nuts
and
tighten them alternately

to draw
the
wheel evenly against
the

hub
and
drum.

3.
Lower
the
vehicle
to the
floor,

and torque
the hub
nuts
to
specifica-

tion.

MAJOR REPAIR OPERATIONS

HOISTING INSTRUCTIONS

Damage
to
steering linkage compo-

nents
and
front suspension struts
may

occur
if
care
is
not
exercised when
po-

sitioning
the
hoist adapters
of 2
post

hoists prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

lower arms
or the
No.
1
crossmember.

Do
not
allow
the
adapters
to
contact

the steering linkage.
If the
adapters

are placed under
the
crossmember,
a

piece
of
wood (2x4x16 inches) should

be placed
on the
hoist channel
be-

tween
the
adapters. This will prevent

the adapters from damaging
the
front

suspension struts.

FRONT WHEEL GREASE

SEAL
AND
BEARING

REPLACEMENT AND/OR

REPACKING

If bearing adjustment will
not
elimi-

nate looseness
or
rough
and
noisy
op-

eration,
the hub and
bearings should

be cleaned, inspected,
and
repacked

with specified wheel grease.
If the

bearing cups
or the
cone
and
roller

assemblies
are
worn
or
damaged, they

should
be
replaced.

DRUM BRAKES

1.
Raise
the
vehicle until
the
wheel

and tire clear
the
floor.

2.
Remove
the
wheel cover
or hub
cap.
Remove
the
grease
cap
from
the

hub.
Remove
the
cotter
pin,
nut
lock,

adjusting
nut, and
flat washer from

the spindjej, Remove
the
outer bearing

cone
and
roller assembly
(Fig.
1).

3.
Pull
the
wheel,
hub, and
drum

assembly
off the
wheel spindle.

4.
Remove
and
discard
the
grease

retainer. Remove
the
inner bearing

Too/-T69L-J102-A

F1476-A

FIG. 13—Removing Front Wheel

Bearing Cup—Except Lincoln

Continental
cone
and
roller assembly from
the hub

with Tool 1175AE.

5.
Clean
the
lubricant
off the
inner

and outer bearing cups with solvent

and inspect
the
cups
for
scratches,

pits,
excessive wear,
and
other
dam-

age.
If
the
cups
are
worn
or
damaged,

remove them with Tool T69L-1102-A

(Fig.
13).

6. Thoroughly clean
the
inner
and

outer bearing cone
and
roller assem-

blies with solvent
and dry
them thor-

oughly.
Do not
spin
the
bearings with

compressed
air.

Inspect
the
cone
and
roller assem-

blies
for
wear
or
damage,
and
replace

them
if
necessary.
The
cone
and
roller

assemblies
and the
bearing cups

should
be
replaced
as a
unit
if
damage

to either
is
encountered.

7. Thoroughly clean
the
spindle
and

the inside
of the hub
with solvent
to

remove
all old
lubricant.

Cover
the
spindle with
a
clean

cloth,
and
brush
all
loose dust
and

dirt from
the
brake assembly.
To
pre-

vent getting dirt
on the
spindle, care-

fully remove
the
cloth from
the

spindle.

8.
If the
inner and/or outer bearing

cup(s) were removed, install
the re-

placement cup(s)
in the hub
with
the

tool shown
in Fig.
14.
Be
sure
to
seat

the cups properly
in the hub.

9. Pack
the
inside
of the hub
with

specified wheel bearing grease.
Add

lubricant
to the hub
only until
the

grease
is
flush with
the
inside diame-

ter
of
both bearing cups
(Fig.
15).procarmanuals.com