1969 FORD MUSTANG wheel bolt torque

03-05-20
Steering Columns And Linkage

03-05-20

placed if it becomes worn or damaged

(Figs.
18 through 21). Do not attempt

to straighten the sleeve if damaged.

1.
Remove the spindle connecting

rod end assemblies as described in the

previous sub-section.

2.
Screw the spindle rod end assem-

blies into the new sleeve the same

number of turns as the ends that were

removed. Do not tighten the clamp

bolts at this time.

3.
Position the sleeve and end as-

sembly on the center link and the

spindle arm. Install the attaching nut,

torque it to specification, and install

the cotter pin.

4.
Check and, if necessary, adjust

toe-in (Part 3-1). After toe-in is

checked and adjusted, oil the sleeve

clamp bolts then torque them to speci-

fication. The sleeve clamp must be in-

stalled as shown in Figs. 18 through

21.

CENTER LINK

REPLACEMENT

The center link connecting the Pit-

man arm and the idler arm is non-

adjustable and is provided with ta-

pered holes to accommodate the ball

studs (Figs. 18 through 21). The link

should be replaced when damaged or

when worn at the ball studs. On Lin-

coln Continental models, the link

should be replaced if excessive loose-

ness is noticed in either ball stud sock-

et.

REMOVAL

1.
Raise the vehicle on a hoist and

position safety stands.

2.
Remove the cotter pins and nuts

that attach both inner connecting rod

ends to the center link (Figs. 18

through 21).

3.
Disconnect the inner connecting

rod ends from the center link using

Tool 3290-C (Fig. 22).

4.
Remove the cotter pin and nut

attaching the idler arm to the center

link. Disconnect the idler arm from

the center link using Tool 3290-C for

Lincoln Continental models only.

5.
Remove the cotter pin and nut

attaching the Pitman arm to the cen-

ter link. Disconnect the Pitman arm

from the center link (use Tool 3290-C)

and remove the center link. On ve-

hicles equipped with the non-integral

power steering system, remove the

center link from the control valve as

detailed in Part 3-7.

INSTALLATION

1.
Replace the rubber seals on the
spindle connecting rod ends, if re-

quired.

2.
Position the center link to the

Pitman arm and idler arm and install

the attaching nuts loosely. On all ve-

hicles except Lincoln Continental

models, place the idler arm and the

front wheels in the straight ahead po-

sition to insure keeping the steering

wheel aligned and to prevent bushing

damage after the attaching nuts have

been torqued. On Lincoln Continental

models, insure that the seal is properly

installed on the center link. Torque

the nuts to the low end of the specifi-

cation. Continue to tighten each nut

until the slots in the nut align with the

hole in the stud. Then install a new

cotter pin.

3.
Position the spindle connecting

rod ends to the center link and install

the attaching nuts. Torque the nuts to

the low end of the specification. Con-

tinue to tighten each nut until the

slots in the nut align with the hole in

the stud. Then, install a new cotter

pin.

4.
Remove the safety stands, lower

the vehicle, check and adjust toe-in to

specification (Part 3-1).

STEERING IDLER ARM

AND BRACKET ASSEMBLY

REPLACEMENT

REMOVAL

If the idler arm bushings are worn

the complete idler arm assembly must

be replaced. In Lincoln Continental

models, if the socket at the idler

bracket is excessively loose, replace

the complet assembly.

1.
Remove the cotter pin and nut

attaching the steering center link at

the idler arm (Figs. 18 through 21).

2.
Disconnect the center link from

the idler arm (on Lincoln Continental

models, use Tool 3290-C).

3.
Remove the two bolts that attach

the idler arm and bracket assembly to

the frame.

INSTALLATION

1.
Secure the new idler arm and

bracket assembly to the frame with

the two attaching bolts (nuts and flat

washers as shown in Figs. 18, 19 and

21).

2.
On all vehicles except Lincoln

Continental models, place the idler

arm and the front wheels in the

straight ahead position to insure keep-

ing the steering wheel aligned and to
prevent bushing damage after the at-

taching nut has been torqued. Insert

the center link stud through the hole

in the end of the idler arm and install

the nut and washer.

On Lincoln Continental models, in-

sert the center link stud through the

hole in the end of the idler arm insur-

ing that the seal is properly installed

on the center link.

3.
Torque the idler arm rod nut to

specification and install a new cotter

pin.

PITMAN ARM

REPLACEMENT

REMOVAL

1.
Remove the cotter pin from the

castellated nut that attaches the steer-

ing center link to the Pitman arm.

Remove the castellated nut.

2.
Disconnect the steering center

link from the Pitman arm with tool

3290-C.

3.
Remove the Pitman arm attaching

nut and lock washer.

4.
Position the front wheels in the

straight ahead position. Remove the

Pitman arm with tool T64P-3590-F

(Fig. 23).

INSTALLATION

1.
With the front wheels in the

straight ahead position, place the Pit-

man arm on the sector shaft making

sure it is pointing forward.

2.
Install the nut and lock washer.

Torque the nut to specification.

G1663-A

FIG. 23— Removing Pitman

Arm—Typicalprocarmanuals.com

03-06-02
Manual Steering

03-06-02

IN-VEHICLE ADJUSTMENTS AND REPAIRS

STEERING WORM AND

SECTOR

GEAR ADJUSTMENTS

The ball nut assembly and the sec-

tor gear must be adjusted properly to

maintain minimum steering shaft end

play (a factor of preload adjustment)

and minimum backlash between sector

gear and ball nut. There are only two

possible adjustments within the recir-

culating ball-type steering gear, and

these should be made in the following

order to avoid damage or gear failure.

1.
Disconnect the Pitman arm from

the steering Pitman-to-idler arm rod.

2.
Loosen the nut which locks the

sector adjusting screw (Fig. 3), and

turn the adjusting screw counterclock-

wise.
(On models equipped with the

Cobra Jet engine, it may be necessary

to use a suitable holding tool with an

extension and a long screwdriver to

make the gear adjustment).

3.
Measure the worm bearing pre-

load by attaching an in-lb torque

wrench to the steering wheel nut (Fig.

4).
With the steering wheel off center,

read the pull required to rotate the

input shaft approximately 1 1/2 turns

either side of center. If the torque or

preload is not within specification

(Part 3-1), adjust as explained in the

next step.
.•ADJUSTER
LOCK
NUT

SECTOR
SHAFT

ADJUSTING
SCREW
G
1627-A

FIG. 3—Steering Gear

Adjustments—Typical

4.
Loosen the steering shaft bearing

adjuster lock nut, and tighten or back

off the bearing adjuster (Fig. 1) to

bring the preload within the specified

limits.

5.
Tighten the steering shaft bear-

ing adjuster lock nut, and recheck the

preload.

6. Turn the steering wheel slowly to

either stop. Turn gently against the

stop to avoid possible damage to the

ball return guides. Then rotate the

wheel 2-3/4 turns to center the ball

nut.
7.
Turn the sector adjusting screw

clockwise until the specified torque

(Part 3-13) is necessary to rotate the

worm past its center (high spot) (Fig.

1).

8. While holding the sector adjust-

ing screw, tighten the sector adjusting

screw locknut to specification, and re-

check the backlash adjustment.

9. Connect the Pitman arm to the

steering arm-to-idler arm rod.

G-1495-A

FIG. 4—Checking Steering Gear

Preload—Typical

REMOVAL AND INSTALLATION

STEERING GEAR

REMOVAL

1.
Remove the bolt(s) that retains

the flex coupling to the steering shaft.

2.
Remove the nut and lock washer

that secures the Pitman arm to the

sector shaft using Tool T64P-3590-F

(Fig. 5).

3.
To obtain clearance on some

models equipped with standard trans-

mission, it may be necessary to dis-

connect the clutch linkage. On some

8-cylinder models, it may be necessary

to lower the exhaust system.

4.
Remove the steering gear-to-side

rail bolts and remove the gear.
Too /-MB
STEERING
GEAR
HOUSING

T64P-3590.F

(PITMAN
"APU'^M
-
.-. •
-"
•.:,.17''i.a—
r.iMI.
A

F'G.
5—Removing Pitman Arm
INSTALLATION

1.
Position the steering gear and

flex coupling in place; then, install

and torque the steering gear-to-side

rail bolts to specification (Part 3-13).

2.
If the clutch linkage has been

disconnected, reposition, install and

adjust it. If the exhaust system has

been lowered, reinstall it to its proper

position.

3.
Position the Pitman arm and the

sector shaft and install the attaching

nut and lock washer. Torque the nut

to specification.

4.
Install and connect the flex cou-

pling attaching nut(s) and torque it to

specification (Part 3-13).procarmanuals.com

03-07-02
Ford Design Non-Integral Power Steering System

03-07-02

PUMP AND RESERVOIR

CONTROL VALVE

POWER CYLINDER

FIG. 7—Non-Integral Power Steering System
G 1651-A

IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

HOISTING INSTRUCTIONS

Damage
to
suspension and/or steer-

ing linkage components
may
occur
if

care
is not
exercised when positioning

the hoist adapters
of 2
post hoists

prior
to
lifting
the
vehicle.

If
a 2
post hoist
is
used
to
lift
the

vehicle, place
the
adapters under
the

front suspension lower arms.
Do not

allow
the
adapters
to
contact
the

steering linkage.

CONTROL VALVE CENTERING

SPRING ADJUSTMENT

1.
Raise
the
vehicle
and
remove
2

spring
cap
attaching screws
and
lock

washers
and
remove
the
spring
cap.

2.
Tighten
the
adjusting
nut
snug

(90-100 in-lbs); then, loosen
the nut

1/4 turn. Make sure that
the nut ro-

tates
1/4
turn
(90
degrees)
on the

threads
of the
bolt.
Do not
tighten
the

adjusting
nut too
tight.

3.
Position
the
spring
cap to the

valve housing. Lubricate
and
install

the
two
attaching screws
and
washers.

Torque
the
screws
to
72-100 in-lbs.

4.
Lower
the
vehicle.

5.
Start
the
engine
and
check
the

turning effort with
a
spring scale.

With
the
spring scale attached
to the

rim
of the
steering wheel,
the
effort
to
turn
the
wheel
in
both directions

should
not
exceed
12
pounds.

CONTROL VALVE
TO
POWER

STEERING CYLINDER HOSE

1.
Raise
the
vehicle
on a
hoist
and

place
a
drain
pan
under
the
power

cylinder.

2.
Disconnect
the
hose from
the

power cylinder
and
allow
the
fluid
to

drain from
the
hose. Then, disconnect

the hose from
the
control valve.

3.
Connect
the
unmarked
end of

the shorter tube
(9 7/16 in
long)
to

valve port
C
(Fig. 2). Hold
the
tube
so

that
the
bend parallels
the
surface
of

valve shown
in Fig. 2,
tighten
the nut.

PLANE
OF
TUBE BEND
IN

3A717 HOSE
TO BE
PARALLEL

WITH THIS SURFACE ON VALVE.

CLEARANCE BETWEEN

COUPLING TO
BE 1/16-

1/8 INCH
IN
THIS AREA

G 1503-A

FIG. 2—Power Steering Hose

Installation
Connect
the
opposite
end to the
lower

port
in the
cylinder. Hold
the
tube
se-

curely while tightening
the nut to pre-

vent twisting
the
tube. Connect
the

other tube
(9 5/8 in
long)
to
port
A,

making sure that tube
is
parallel with

the other tube.

4.
Remove
the
drain
pan and
lower

the vehicle.

5.
Fill
the
power steering pump res-

ervoir with fluid
to the
proper level

(Part
3-1).

6. Start
the
engine
and
turn
the

steering wheel
to
each
end of its
travel

several times
to
cycle
the
system.

Then, check
for
leaks.

7.
Stop
the
engine
and
again check

the power steering fluid level.
Add

fluid
as
required.

POWER STEERING PUMP

TO CONTROL VALVE HOSE

REMOVAL

1.
Remove
the
fluid from
the
pump

reservoir with
a
suction
gun.

2.
Raise
the
vehicle
on a
hoist.

3.
Remove
the
clamp retaining
the

hose tubes
to the
control valve.

4.
Disconnect
the
fluid return
and

pressure hoses from
the
control valve

and allow
the
fluid
to
drain into
a

pan.procarmanuals.com

03-07-03
Ford Design Non-Integral Power Steering System

03-07-03

5.
Lower the vehicle and disconnect

the fluid return hose from the reser-

voir.

6. Disconnect the fluid pressure

hose from the pump outlet fitting.

7.
Remove 1 bolt attaching the

hoses,
insulator, and the retainer to

the frame side rail and remove the

hoses,
and the insulator and retainer

as an assembly from the vehicle.

8. Remove the pressure and return

hoses from the retainer and insulator.

INSTALLATION

1.
Install the pressure and return
hoses in the insulator and retainer.

Paint stripe on pressure hose must be

aligned with slot in insulator. Paint or

tape band on return hose must be cen-

tered in insulator. Position the assem-

bly to the frame side rail and install

the attaching bolt.

2.
Place a hose clamp on the fluid

return hose and install the hose on the

power steering pump reservoir return

fitting.

3.
Torque the pump outlet fitting to

specification (Part 3-13). Then, con-

nect the pressure hose to the outlet fit-

ting and torque the fitting to specifica-

tion.
4.
Raise the vehicle and connect the

pressure and return lines to the con-

trol valve.

5.
Install the clamp to retain the

hose tubes to the control valve.

6. Lower the vehicle and fill the

power steering pump reservoir with

fluid, C1AZ-19582-A, to the proper

level (Part 3-1).

7.
Start the engine and turn the

steering wheel to each end of its travel

several times to cycle the system.

Then, check for fluid leaks.

8. Stop the engine and again check

the power steering fluid level (Part

3-1). Add fluid as required.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to suspension and/or steer-

ing linkage components may occur if

care is not exercised when positioning

the hoist adapters of 2 post hoists

prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

front suspension lower arms. Do not

allow the adapters to contact the

steering linkage.

STEERING GEAR

Refer to Group 3-6, Section 3 for

detailed instructions.

POWER STEERING PUMP

Refer to Group 3-10, Section 3 for

detailed instructions.

POWER STEERING CONTROL

VALVE

REMOVAL

1.
Disconnect the 4 fluid line fit-

tings at the control valve, and drain

the fluid from the lines. Turn the front

wheels to the left and right several

times to force all the fluid from the

system.

2.
Loosen the clamping nut and

bolt at the right end of the sleeve.

3.
Remove the roll pin from the

steering arm-to-idler arm rod -through

the slot in the sleeve.

4.
Remove the control valve ball

stud nut.

5.
Using the tool shown in Fig. 3,

remove the ball stud from the sector

shaft arm.
VALVE

Too/-3290-C BALL STUD PITMAN ARM

FIG. 3—Removing Control Valve

Ball Stud

6. After turning the front wheels

fully to the left, unthread the control

valve from the center link steering

arm-to-idler arm rod.

INSTALLATION

1.
Thread the valve onto the center

link until about four threads are still

visible on the link.

2.
Position the ball stud in the sec-

tor shaft arm.

3.
Measure the distance between

the center of the grease plug in the

sleeve and the center of the stud at the

inner end of the left spindle connect-

ing rod (Fig. 4). The distance should

be 5 5/8 inches for Montego, Falcon

and Fairlane vehicles. The distance

should be 4 7/8 inches for Mustang

and Cougar models. If the distance is

not correct, disconnect the ball stud

from the sector shaft arm and turn the

valve on the center link to increase or

decrease the distance.

4.
When the correct distance is ob-

tained and the ball stud is positioned

in the sector shaft arm, align the hole

in the steering arm-to-idler arm rod

with the slot near the end of the valve
sleeve. Install the roll pin in the rod

hole to lock the valve in position on

the rod.

5.
Torque the valve sleeve clamp

bolt to specification.

6. Install the nut on the ball stud,

and torque the nut to specification.

Install a new cotter pin.

7.
Connect the fluid lines to the

control valve, and tighten all fittings

securely. Do not over-tighten.

8. Fill the fluid reservoir with the

specified fluid to the cross hatched

area on the dip stick.

9. Start the engine and run it at

idle speed for about two minutes to

warm the fluid in the power steering

system.

10.
Turn the steering wheel all the

way to the left and right several times,

and check the system for fluid leaks.

11.
Increase the engine speed to

about 1000 rpm, and turn the steering

wheel all the way to the left and right

several times.

CONTROL VALVE CONNECTING ROD STUD

LUBRICATION PLUG

G1653-A

FIG. 4—Control Valve Installation

Measurements—All Modelsprocarmanuals.com

03-08-03
Ford Design Integral Power Steering Gear

03-08-03

factory adjustments will change. These

changes in adjustment do not neces-

sarily affect the satisfactory operation

of the steering gear assembly, and

therefore ordinarily do not require

readjustment unless there is excessive

lash or other malfunctioning.

ADJUSTMENT IN

VEHICLE

The only adjustment which can be

performed is the total over center

position load, to eliminate excessive

lash between the sector and rack

teeth.

1.
Disconnect the pitman arm from

the sector shaft.

2.
Disconnect the fluid return line

at the reservoir, at the same time cap

the reservoir return line pipe.

3.
Place the end of the return line

in a clean container and cycle the
INPUT SHAFT

SECTOR SHAFT

ADJUSTMENT SCREW

C1547- A

FIG.
2—Adjusting Mesh Load

steering wheel in both directions as re-

quired, to discharge the fluid from the

gear.
4.
Remove the ornamental cover

from the steering wheel hub and turn

the steering wheel to 45 degrees from

the left stop.

5.
Using an in-lb torque wrench on

the steering wheel nut, determine the

torque required to rotate the shaft

slowly through an approximately 1/8

turn from the 45 degree position.

6. Turn the steering gear back to

center, then determine the torque re-

quired to rotate the shaft back and

forth across the center position. Loos-

en the adjuster nut, and turn the ad-

juster screw in (Fig. 2) until the read-

ing is 8-9 in-lb greater than the torque

45 degrees from the stop.

Tighten the lock nut while holding

the screw in place.

7.
Recheck the readings and replace

pitman arm and steering wheel hub

cover.

8. Connect the fluid return line to

the reservoir and fill the reservoir with

specified lubricant to the proper level.

REMOVAL AND INSTALLATION

REMOVAL

1.
Disconnect the pressure and the

return lines from the steering gear.

Plug the lines and the ports in the

gear to prevent entry of dirt.

2.
Remove the two bolts that secure

the flex coupling to the steering gear

and to the column.

3.
Raise the vehicle and remove the

sector shaft attaching nut.

4.
Remove the Pitman arm from

the sector shaft with Tool T64P-

3590-F.
Remove the tool from the

Pitman arm. Do not damage the

seals.

5.
If working on a vehicle equipped

with a standard transmission, remove

the clutch release lever retracting

spring to provide clearance for remov-

ing the steering gear.
6. Support the steering gear then

remove the three steering gear attach-

ing bolts.

7.
Work steering gear free of the

flex coupling and remove it from the

vehicle.

8. If the flex coupling stayed on the

input shaft, lift if off the shaft at this

time.

INSTALLATION

1.
Slide the flex coupling into place

on the steering shaft. Turn the steer-

ing wheel so that the spokes are in the

horizontal position.

2.
Center the steering gear input

shaft.

3.
Slide the steering gear input

shaft into the flex coupling and into
place on the frame side rail. Install

the three attaching bolts and torque

them to specification.

4.
Make sure that the wheels are in

the straight ahead position, then in-

stall the Pitman arm on the sector

shaft. Install and tighten the sector

shaft and install and tighten the at-

taching bolts to specification.

5.
Move the flex coupling into

place on the input and steering co-

lumn shaft and install and tighten the

attaching bolts to specification.

6. Connect and tighten the fluid

pressure and the return line to the

steering gear.

7.
Fill the power steering pump and

cycle the steering gear. Check for

leaks and again check the fluid level.

Add fluid as required.

MAJOR REPAIR OPERATIONS

In most cases, complete disassembly

of the power steering gear will not be

necessary. It is suggested that only

those assemblies that are faulty be dis-

assembled. Disassembly and reassem-

bly of the unit and the subassemblies

must be made on a clean workbench.

As in repairing any hydraulically op-

erated unit, cleanliness is of utmost

importance. Therefore, the bench,
tools,
and parts must be kept clean at

all times. Thoroughly clean the exter-

ior of the unit with a suitable solvent

and when necessary, drain as much of

the hydraulic oil as possible. Handle

all parts very carefully to avoid nicks,

burrs,
scratches and dirt, which could

make the parts unfit for use. Do not

clean, wash or soak seals in cleaning

solvent.
VALVE CENTERING

SHIM REPLACEMENT

1.
Hold the steering gear over a

drain pan in an inverted position and

cycle the input shaft several times to

drain the remaining fluid from the

gear.

2.
Mount the gear in a soft-jawed

vise.procarmanuals.com

03-09-02

Saginaw Design Integral Power Steering Gear

03-09-02

WORM

ADJUSTER PLUG

TORSION BAR

STUB SHAFT

SEAL

NEEDLE BEARINGS

TEFLON RING

TEFLON SEALS

SECTOR SHAFT

FIG.l —
Power
Steering Gear—Sectional View
G 1650-A

REMOVAL
AND
INSTALLATION

REMOVAL

1.
Disconnect
the
pressure
and the

return line from
the
steering gear.

Plug
the
lines
and the
ports
in the

gear to prevent entry of dirt.

2.
Remove the two bolts that secure

the flex coupling
to the
steering gear

and
to
the column.

3.
Raise
the
vehicle
and
remove
the

Pitman arm attaching nut.

4.
Remove
the
Pitman arni from

the sector shaft with Tool T64P-3590-

F.
Remove
the
tool from
the
Pitman

arm.

5.
If
working
on a
vehicle equipped

with
a
standard transmission, remove
the clutch release lever retracting spring

to provide clearance
for
removing
the

steering gear.

6. Support
the
steering gear then

remove
the
three steering gear attach-

ing bolts.

7.
Work
the
steering gear free
of

the flex coupling
and
remove
it
from

the vehicle.

8.
If
the flex coupling stayed
on the

input shaft, lift
it off the
shaft
at

this time.

INSTALLATION

1.
Slide
the
flex coupling into place

on
the
steering shaft. Turn
the
steer-
ing wheel
so
that
the
spokes
are in

the horizontal position.

2.
Center
the
steering gear input

shaft.

3.
Slide the steering gear input shaft

into
the
flex coupling
and
into place

on
the
frame side rail. Install the three

attaching bolts
and
torque them
to

specification.

4.
Make sure that
ihe
wheels
are

in
the
straight-ahead position, then

install
the
Pitman
arm on the
sector

shaft. Install
and
tighten
the
sector

shaft attaching nut to specification.

5.
Move the flex coupling into place

on
the
input shaft
and
steering columnprocarmanuals.com

03-11-01
Eaton Power Steering Pump

03-11-01

PART 3-11 Eaton Power Steering Pump

COMPONENT INDEX
MODEL APPLICATION

3
§>
"o

4

POWER STEERING PUMP

Cleaning and Inspection (See Part 03-01)

Description

N/A
N/A
N/A
N/A
N/A
N/A

N/A
N/A
11-01

N/A
11-01

Disassembly and Overhaul

N/A
N/A

N/A
N/A

N/A
N/A

N/A
N/A
11-03

N/A
11-03

Removal and Installation

N/A
N/A
N/A
N/A

N/A
N/A
N/A
N/A
11-01
N/A

11-01

POWER STEERING PUMP RESERVOIR

Removal and Installation

N/A
N/A
N/A

N/A
N/A
N/A

N/A

N/A

11-01
N/A

11-01

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

l
DESCRIPTION

The roller-type hydraulic pump,

driven by the crankshaft, draws auto-

matic transmission fluid down the res-

ervoir and provides fluid pressure for

the system. Steering gear lubrication
is also provided by the same fluid

from the reservoir. Within the pump

itself is a flow-control and pressure-

relief valve which governs the pres-
sures within the steering system ac-

cording to the varying conditions of

operation. After fluid has passed from

the gear, it returns to the reservoir.

REMOVAL AND INSTALLATION

POWER STEERING PUMP

REMOVAL

1.
Open the hood, and install fend-

er covers.

2.
If the vehicle is equipped with air

conditioning, loosen the compressor

adjusting and support bracket bolts

and remove the drive belt.

3.
Loosen the generator adjusting

and support bracket bolts, and remove

the drive belts.

4.
Remove the fan, pulley, and spa-

cer.

5.
Raise the vehicle.

6. Remove the crankshaft damper

bolt and washer. Remove the damper

with Tool 6306-AG. Remove the drive

key.

7.
Disconnect the pump inlet line at

the pump, and plug the end of the line

to prevent the loss of fluid. Disconnect

the pump pressure line at the pump.
8. Remove the pump-to-engine

front cover cap screws, and remove

the pump. Remove the seal from the

front cover.

INSTALLATION

1.
Install a new seal on the engine

front cover.

2.
Align the slot in the pump rotor

shaft with the drive key in the crank-

shaft, and slide the pump onto the

shaft. Install the pump-to-engine front

cover cap screws. Torque the cap

screws to specification.

3.
Connect the pump inlet line and

the pressure line.

4.
Install the damper drive key,

damper, washer and bolt. Torque the

bolt to specification.

5.
Install the fan, pulley, and spa-

cer. Install the generator drive belts.

Adjust the belt tension, and tighten

the adjusting and support bracket

bolts.
6. If the vehicle is equipped with air

conditioning, install the compressor

drive belt. Adjust the belt tension, and

tighten the adjusting and support

bracket bolts.

7.
Run the engine at idle speed,

and check the fluid level in the reser-

voir. If required, add the specified au-

tomatic transmission fluid. Turn on

the windshield wipers. Rotate the

steering wheel from stop to stop sever-

al times to bleed the air from the sys-

tem. Recheck the fluid level.

POWER STEERING PUMP

RESERVOIR

WITHOUT AIR

CONDITIONING

Removal

1.
Remove the reservoir cover andprocarmanuals.com

03-12-03

Wheels And Tires

03-12-03

DISC BRAKES

1.
Raise the vehicle until the wheel

and tire clear the floor.

2.
Pry off the wheel cover and re-

move the grease cap (Fig. 2) from the

hub.

3.
Wipe the excess grease from the

end of the spindle, and remove the ad-

justing nut cotter pin and nut lock.

4.
Loosen the bearing adjusting nut

three turns. Then, rock the wheel,

hub,
and rotor assembly in and out

several times to push the shoe and lin-

ings away from the rotor.

5.
While rotating the wheel, hub,

and rotor assembly, torque the adjust-

ing nut to 17-25 ft-lbs to seat the

bearings (Fig. 4).

6. Back the adjusting nut off one

half turn. Then, retighten the adjust-

ing nut to 10-15 in-lbs with a torque

wrench or finger tight.

7.
Locate the nut lock on the ad-

justing nut so that the castellations on

the lock are aligned with the cotter

pin hole in the spindle.

8. Install a new cotter pin, and

bend the ends of the cotter pin around

the castellated flange of the nut lock.

9. Check the front wheel rotation.

If the wheel rotates properly, install

the grease cap and the hub cap or

wheel cover. If the wheel still rotates

roughly or noisily, clean or replace the

bearings and cups as required.

10.
Before driving the vehicle,
pump the brake pedal several times to

obtain normal brake lining to rotor

clearance and restore normal brake

pedal travel.

BALANCING LIFE

GUARD TIRE

Tires fitted with the Life Guard

Safety Spare are balanced in the same

manner as conventional tires. If an ex-

cessive out of balance condition exists

the following procedure can be used to

correct the condition:

1.
Remove the core housing and de-

flate both air chambers.

2.
Install the core housing.

3.
Unseat the beads of tire with the

bead breakers away from the valve

stem as shown in Fig. 5.

F 1383

FIG. 5—Breaking Top Bead of

Tire From Wheel Rim
4.
Rotate tire casing 90 degrees on

the wheel rim.

5.
Rotate the tire casing back and

forth on the rim to center the valve.

6. Inflate both chambers of the tire

following steps 13 through 15 of the

Tire Installation procedure.

7.
Balance the tire in the normal

manner.

CORRECTING VIBRATION

AND SHAKE-

LIFE GUARD TIRE

The condition of excessive vibration

and shake is generally the result of an

incorrect pressure relationship between

the inner and outer air chambers that

may cause the life guard to shift posi-

tion within the tire. The following

procedure should be used to correct

vibration and shake conditions:

1.
Check pressure of the inner and

outer air chambers on all four tires.

2.
If the inner chamber has at least

five psi more pressure than the outer

chamber the pressures should be ad-

justed and the tires rebalanced if nec-

essary.

3.
If the pressures of the inner and

outer air chambers are equal the Air

Container is leaking. To repair the

leaking air container the recommend-

ed procedures for the removal, repair

of air container, mounting, and bal-

ancing should be followed.

REMOVAL AND INSTALLATION

HOISTING INSTRUCTIONS

Damage to steering linkage compo-

nents and front suspension struts may

occur if care is not exercised when po-

sitioning the hoist adapters of 2 post

hoists prior to lifting the vehicle.

If a 2 post hoist is used to lift the

vehicle, place the adapters under the

lower arms or the No. 1 crossmember.

Do not allow the adapters to contact

the steering linkage. If the adapters

are placed under the crossmember, a

piece of wood (2x4x16 inches) should

be placed on the hoist channel be-

tween the adapters. This will prevent

the adapters from damaging the front

suspension struts.

WHEELS AND TIRES

WHEEL AND TIRE

REMOVAL

1.
Pry off the wheel hub cap or
wheel cover. Loosen but do not re-

move the wheel hub nuts.

2.
Raise the vehicle until the

wheel and tire clear the floor.

3.
Remove the wheel hub nuts

from the bolts, and pull the wheel

and tire from hub and drum.

F1424-
A

FIG.
6—Bead
Loosening Tool
REMOVING CONVENTIONAL

TIRE FROM WHEEL

The tire can be demounted on a

mounting machine. Be sure that the

outer side of the wheel is positioned

downward. If tire irons are used, fol-

low the procedure given here.

1.
Remove the valve cap and core,

and deflate the tire completely.

2.
With a bead loosening tool,

break loose the tire side walls from

the wheel (Fig. 6).

3.
Position the outer side of the

wheel downward, and insert two tire

irons about eight inches apart between

the tire inner bead and the back side

of the wheel rim. Use only tire irons

with rounded edges or irons designed

for removing tubeless tires.

4.
Leave one tire iron in position,

and pry the rest of the bead over the

rim with the other iron. Take small

bites with the iron around the tire inprocarmanuals.com