1969 FORD MUSTANG ECU

07-02-08
C4 Automatic Transmission

07-02-08

8. Install the outer downshift lever

and attaching nut, and torque the nut

to specification. Install the downshift

linkage rod to the downshift lever.

9. Install the switch wires. Connect

the wire multiple connector. Check

the operation of the switch in each de-

tent position. The engine should start

only with the transmission selector

lever in N (neutral) and P (park).

SELECTOR LEVER

REPLACEMENT—CONSOLE SHIFT

FORD-METEOR

1.
Raise the vehicle and disconnect

the link assembly from the selector

lever arm (Fig. 6).

2.
Lower the vehicle. Remove the

four screws and plates securing the se-

lector lever handle to the lever. Re-

move the handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

quadrant.

5.
Remove the four bolts that at-

tach the selector lever housing to the

floor pan and remove the selector

lever and housing.

6. Position the new selector lever

and housing assembly on the floor pan

and install the attaching bolts.

7.
Connect the bulb socket to the

quadrant and the neutral start switch

wires to the plug connector.

8. Raise the vehicle and secure the

link assembly to the selector lever arm

with the bushing, insulator, flat wash-

er and cotter pin (Fig. 6). Lower the

vehicle.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tr*rtt control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 7).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.
DETENT PAWL

LOCK NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG. 72—Typical Selector Lever Detent Pawl Adjustment

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se-

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-31bs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 12. With a feeler

gauge, check the clearance between

the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 12.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.
19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

7).

23.
Adjust the linkage as required.

J r the vehicle.

MUSTANG

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 8).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.

5.
Disconnect the dial indicator

light.

6. Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

7.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

8. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

9. Install the selector lever handle.

10.
Position the selector lever as

shown in Figure 12. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearance

should be 0.005 to 0.010 inch. If nec-

essary adjust the height of the detent

pawl as shown in Figure 12.procarmanuals.com

07-02-11
C4 Automatic Transmission
07-02-11

REMOVAL AND INSTALLATION

An oil impregnated plastic grommet

is incorporated in the end of the man-

ual shift linkage lever arm on all col-

umn shift vehicles. A special tool

T67P-7341-A is required to install the

grommet in the manual lever, and to

install the manual linkage rod into the

grommet. Refer to Part 7-1, Section

2,
for the grommet replacement pro-

cedures.

TRANSMISSION REMOVAL

1.
Raise the vehicle and remove the

converter cover attaching bolts, at the

lower front side of the converter hous-

ing. Remove the cover.

2.
Remove the two conveter drain

plugs (Fig. 20). Drain the fluid from

the converter. Install the two convert-

er drain plugs.

3.
Remove the drive shaft and in-

stall the extension housing seal repla-

cer tool in the extension housing.

4.
Remove the vacuum line hose

from the transmission vacuum unit.

Disconnect the vacuum line from the

retaining clip.

5.
Remove the two extension

housing-to-crossmember attaching

bolts.

6. Remove the speedometer cable

from the extension housing.

7.
Disconnect the exhaust pipe

flange from the manifolds.

8. Remove the parking brake cable

from the equalizer lever.

9. Remove the fluid filler tube from

the pan and drain the transmission

fluid on PEA models. On PEB and

PEE models, loosen the transmission

CONVERTER A
ATT,
pan bolts and drain the fluid at one

corner of the pan. Tighten the attach-

ing bolts after the fluid has drained.

10.
Disconnect the fluid cooler lines

from the transmission case.

11.
Remove the manual and kick-

down linkage rods from the transmis-

sion control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to remove

the selector rod from the manual

lever.

12.
On a Mustang, disconnect the

neutral start switch wires from the re-

taining clamps and connectors.

13.
Disconnect the starter cable.

Remove the starter attaching bolts

and remove the starter from the con-

verter housing.

14.
On PEB and PEE models, lift

the fluid filler tube from the case.

15.
Remove the four converter-

to-flywheel attaching nuts.

16.
Position the transmission jack

to support the transmission and secure

the transmission to the jack with a

safety chain.

17.
Remove the four crossmember

attaching bolts and lower the

crossmember.

18.
Remove the five converter

housing-to-engine attaching bolts.

Lower the transmission (Fig. 21) and

remove it from under the vehicle.

TRANSMISSION

INSTALLATION

1.
With the converter properly in-

D 2043-A

FIG. 20—Converter Drain Plug

Location
FIG. 21—Transmission Mounted

on Jack
stalled, place the transmission on the

jack (Fig. 21). Secure the transmission

to the jack with the safety chain.

2.
Raise the transmission into posi-

tion and install the five converter

housing-to-engine attaching bolts.

Torque the bolts to specification. Re-

move the safety chain from the trans-

mission.

3.
Position the crossmember and

install the four attaching bolts. Torque

the bolts to specifications.

4.
Lower the transmission and in-

stall the extension housing and

crossmember attaching bolts. Torque

the bolts to specification.

5.
Install the four flywheel to con-

verter attaching nuts. Torque the nuts

to specification.

6. Remove the transmission jack.

Install the fluid filler tube in the

transmission case or pan. Install the

vacuum hose on the transmission vac-

uum unit. Install the vacuum line re-

taining clip.

7.
Connect the fluid cooling lines to

the transmission case.

8. On a Mustang, connect the neu-

tral start switch wires to their respec-

tive connectors and secure the harness

in the retaining clamps.

9. Install the linkage rods on the

transmission downshift and manual

control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to install

a new grommet in the manual lever,

and to install the manual linkage rod

into the grommet.

10.
Connect the speedometer cable

to the extension housing.

11.
Connect the exhaust inlet pipes

to the manifolds.

12.
Install and adjust the parking

brake cable at the equalizer lever.

13.
Install the converter housing

cover and torque the attaching bolts

to specification.

14.
Install the starter and torque

the attaching bolts to specification.

Connect the starter cable.

15.
Install the drive shaft. Torque

the companion flange U-bolts attach-

ing nuts to specification.

16.
Lower the vehicle. Fill the

transmission to the proper level with

the specified fluid. Adjust the manual

and downshift linkage.procarmanuals.com

07-02-21
C4 Automatic Transmission
07-02-21

D1893-A

FIG. 58—Removing or Installing

Throttle Booster Valve

4.
Insert the line pressure coasting

boost valve and spring in the body

(Fig. 57).

5.
Place the main regulator valve in

the body (Fig. 57) with the large di-

ameter facing inward. Install the two

springs and the pressure booster valve

and sleeve.

6. Hold the pressure booster valve

cover plate in place and install the

three attaching screws and torque

them to specification.

7.
Place the intermediate servo ac-

cummulator valve and spring in the

body. Install the interim iiate accum-

mulator sleeve and 3-2 control valve.

Secure the cover to the body with the

attaching screw. Torque the screw to

specifications.

8. Position the spring, D2 valve and

the I-2 shift valve in the body.

9. Place the throttle modulator

valve, spring, and 2-3 shift valve in the

body.

10.
Secure the 1-2 shift valve and

the 2-3 valve cover plate to the body

and torque the screws to specifica-

tions.
11.
Place the manual low valve,

spring, and the 2-3 back-out valve in

the body.

12.
Place the cut-back valve in the

body.

13.
Secure the cut-back and the

back-out cover plate to the body with

two screws. Torque the screws to

specifications.

14.
Slide the manual valve into the

body making sure that the notch for

the manual lever is toward the inside

and that the detent notches are facing

upward.

15.
Place the detent plunger and

spring in the body. Depress the spring

and install a new roll pin.

16.
Position a new rubber check

valve in the upper valve body (Fig.

55).

17.
Position the check valve and

spring in the upper valve body (Fig.

55).
Place a new gasket, the separator

plate and the lower valve body in

place on the upper valve body and se-

cure it with the seven attaching

screws. Torque the screws to specifica-

tions.

18.
Secure the oil screen to the

body with the eight attaching screws.

Torque the screws to specifications.

FRONT PUMP

Disassembly

1.
Remove the four seal rings from

stator support.

2.
Remove the five bolts that attach

the stator support to the front pump

housing. Remove the stator support

from the pump housing (Fig. 59).

3.
Remove the front and rear stator

bushings if they are worn or damaged.

Use the cape chisel (Fig. 60) and cut

along the bushing seam until the chisel
D 1731-A

FIG. 60—Removing Stator

Support Bushing

breaks through the bushing wall. Pry

the loose ends of the bushing up with

an awl and remove the bushing.

4.
Remove the drive and driven

gears from the front pump housing.

5.
Press the bushing from the front

pump housing as shown in Fig. 61.

Assembly

1.
Press a new bushing into the

pump housing with the handle and

tool shown in Fig. 61. Make sure the

bushing is installed with the slot and

groove positioned to the rear of the

pump body and 60 degrees below the

horizontal center line.

2.
Install the drive and driven gears

in the pump housing. Each gear has

an identification mark on the side of

the gear teeth that are chamfered. The

chamfered side with the identification

PUMP HOUSING

STATOR SUPPORT

FRONT PUMP SEAL
SEAL RINGS

SELECTIVE

THRUST WASHERS

GASKET

D 1894-B

59—Front Pump and Stator Support Disassembledprocarmanuals.com

07-03-07
FMX Transmission

07-03-07

Gauge Pin

(No.
43 Drill)

NEUTRAL START

SWITCH

ADJUSTMENT

SCREWS

D 1759-A

FIG. 8—
Neutral
Start Switch-

Console Shift—Fairlane-Montego

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
With the manual linkage proper-

ly adjusted and the engine turned off,

place the selector lever in the N (Neu-

tral) position. Then, shift the selector

lever from neutral to 1, to P (park)

and back to neutral. Shifting the se-

lector lever through this shift pattern

should adjust the switch automatical-

ly. If not, adjust it manually as fol-

lows:

2.
With the selector lever in neu-

tral,
remove the selector lever handle

attaching screw and remove the

handle (Fig. 7).

3.
Remove the dial housing attach-

ing screws and remove the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.
NEUTRAL START SWITCH

AND HARNESS ASSEMBLY

32027-A

FIG. 9—Neutral Start Switch—Console Shift—Mustang-Cougar

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing.

6. Lift the switch from the housing

and move the actuator lever all the

way to the left. Then, return the actu-

ator lever to the neutral position as

shown in Figure 9.

7.
Position the neutral switch as-

sembly to the selector lever housing,

and secure with the two attaching

screws.

8. Place the selector lever in the P

(Park) position and check the opera-

tion of the switch. The engine should

start with the selector lever in the

park position. If the engine does not

start, replace the switch. Refer to the

Neutral Start Switch Replacement

procedures in this section.

9. Install the pointer back-up shield

on the housing and lever assembly.

10.
Install the dial housing on the

selector lever housing assembly.

11.
Install the selector lever.'handle.

NEUTRAL START SWITCH

REPLACEMENT-

CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

replacement procedures.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 8).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.procarmanuals.com

07-03-08

FAAX Transmission
07-03-08

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
Place the transmission selector

lever in the N (Neutral) position.

2.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 7).

3.
Lower the vehicle and remove

the selector lever handle attaching

screw and the handle.

4.
Remove the dial housing attach-

ing screws and the housing.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the four selector housing

and lever assembly attaching bolts.

Remove the selector lever and housing

assembly.

8. Remove the two pointer back-up

shield attaching screws and remove

the shield.

9. Remove the two screws securing

the neutral start switch to the selector

lever housing. Push the neutral start

switch harness plug inward and re-

move the switch and harness assembly

(Fig. 9).

10.
Before installing the new

switch, hold it with the wires facing

downward and move the actuator

lever all the way to the left. Then, re-

turn the actuator lever to the neutral

position as shown in Figure 9.

11.
Position the harness and neutral

switch assembly in the selector lever

housing. Secure with the two attach-

ing screws.

12.
Install the pointer back-up

shield on the housing and lever assem-

bly.

13.
Position the selector lever and

housing assembly on the console and

install the attaching bolts.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the dial housing on the

selector lever housing assembly.

17.
Install the selector lever handle.

18.
Raise the vehicle and secure the

manual lever control rod to the selec-

tor lever arm.

19.
Lower the vehicle.

20.
Place the selector lever in the

park position and check the operation

of the switch.
DETENT PAWL

LOCK
NUT

DETENT PAWL

ADJUSTMENT SCREW

DETENT PLATE

D 1644-A

FIG.
10—Typical Selector Lever Detent Pawl Adjustment

SELECTOR LEVER

REPLACEMENT—CONSOLE

SHIFT—FAIRLANE

AND
MONTEGO

1.
Raise the vehicle on a hoist or

jack stands.

2.
Remove the retainer that secures

the manual linkage rod to the lower

end of the manual lever (Fig. 6).

3.
Remove the flat washer and two

insulator washers and disconnect the

rod from the arm.

4.
Working from inside of the vehi-

cle,
remove the selector lever handle

attaching screw. Lift the handle off

the selector lever.

5.
Remove the console trim panel

from the top of the console. Remove

the console retaining screws and re-

move the console.

6. Remove the cover and dial indi-

cator as an assembly.

7.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

8. Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

selector lever housing.

9. Remove the three bolts that se^

cure the selector lever control housing

to the console. Lift the selector lever

housing from the console.

10.
Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

11.
Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

12.
Install the selector lever handle.

13.
Position the selector lever as

shown in Figure 10. With a feeler

gauge,
check the clearance between
the detent pawl and plate. The clear-

ance should be 0.005 to 0.010 inch. If

necessary adjust the height of the de-

tent pawl as shown in Figure 10.

14.
Remove the handle from the se-

lector lever.

15.
Position the selector lever hous-

ing in the console and install the three

attaching bolts. Do not tighten the at-

taching bolts at this time.

16.
Connect the bulb socket to the

selector lever housing and the neutral

start switch wires to the plug connec-

tor.

17.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

18.
Install the cover and dial indi-

cator.

19.
Place the console in position

and install the retaining bolts. Tighten

the selector lever housing attaching

bolts.

20.
Position the console trim panel

and secure it with the attaching

screws.

21.
Install the handle and the but-

ton on the selector lever. Secure the

handle with the set screw.

22.
Secure the manual linkage rod

to the arm with two insulating wash-

ers,
a flat washer and a retainer (Fig.

6).

23.
Adjust the linkage as required.

Lower the vehicle.

MUSTANG-COUGAR

1.
Raise the vehicle and remove the

manual lever control rod attaching nut

(Fig. 7).

2.
Lower the vehicle, remove the se-

lector lever handle attaching screw.

3.
Remove the dial housing attach-

ing screws and the housing.procarmanuals.com

07-03-09
FMX Transmission

07-03-09

4.
Remove the pointer back-up

shield attaching screws and the shield.

5.
Disconnect the dial indicator

light.

6. Disconnect the neutral start

switch and dial indicator light wires

from their connectors at the dash

panel.

7.
Remove the selector housing and

lever assembly attaching bolts. Re-

move the selector lever and housing.

8. Remove the selector lever to

housing attaching nut. Remove the

lever from the housing.

9. Install the selector lever in the

housing and install the attaching nut.

Torque the nut to 20 to 25 ft-lbs.

10.
Install the selector lever handle.

11.
Position the selector lever as

shown in Figure 10. With a feeler

gauge check the clearance between the

detent pawl and plate. The clearince

should be 0.005 to 0.010 inch. If nec-

essary, adjust the height of the detent

pawl as shown in Figure 10.

12.
Remo"~ the handle from tte se-

lector lever.

13.
Install the selector housing and

lever assembly as shown in Figure 4.

Torque the attaching bolts 4-6 ft-lbs.

14.
Connect the dial indicator light.

15.
Connect the neutral start switch

and dial indicator light wires to their

respective connectors at the dash

panel.

16.
Install the pointer back-up

shield and tighten the attaching

screws.

17.
Install the selector lever handle

and tighten the attaching screw.

18.
Position the selector lever in the

D position.

19.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

20.
Lower the vehicle and check the

transmission operation in each selec-

tor lever detent position.

BAND ADJUSTMENTS

FRONT BAND

ADJUSTMENT

1.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Use a clean

drain can equipped with a 100-mesh

screen if the fluid is to be reused.
Too/—
7225-C-13B

/A
-inch
Spacer
FRONT SERVO

ACTUATING LEVER

D 2048-A

FIG.
7
7—Adjusting Front Band—

Typical

2.
Remove the pan, then remove

the fluid filter and clip from the trans-

mission. Clean the inside of the pan.

Remove all gasket material from the

pan and pan mounting face of the

case.

3.
Loosen the front servo adjusting

screw lock nut.

4.
Pull back on the actuating rod,

and insert the 1/4 inch spacer between

the adjusting screw and servo piston

stem (Fig. 11). Tighten the adjusting

screw to 10 in-lbs. torque. Remove the

spacer and tighten the adjusting screw

an additional 3/4 turn. Hold the ad-

justing screw stationary and tighten

the lock nut securely.

5.
Install the transmission fluid

screen and clip. Install the pan using a

new gasket.

6. Refill the transmission to the

FULL mark on the dipstick.

7.
Start the engine and engage the

transmission in each drive range to fill

all fluid passages, then place the selec-

tor lever in the P position. Check the

fluid level and add enough fluid to

bring the level above the ADD mark

on the dipstick.

ALTERNATE FRONT

BAND ADJUSTMENT

1.
Drain the fluid from the trans-

mission. If the same fluid is to be

used again in the transmission after

Che band adjustment, filter the fluid

through a 100-mesh screen as it drains

from the transmission. Re-use the

fluid only if it is in good condition.

2.
Remove and thoroughly clean

the pan and screen. Discard the pan

gasket.

3.
Loosen the front servo adjusting

screw locknut two full turns with a
inch Driv

Detail #2

D.tai\
#3

T-Hond/e
Extension

Tool-758L-7195-A
f/2 inch Driv

Detail
#7

Qj-«—
TM-470 TM-82

D1950-A

FIG. 12—Front and Rear Band

Adjusting Tools

9/16-inch wrench. Check the. adjusting

screw for free rotation in the actuating

lever after the lock nut is loosened,

and free the screw if necessary.

4.
Pull the adjusting screw end of

the actuating lever away from the

servo body, and insert the 1/4 inch

spacer (Fig. 12) between the servo pis-

ton stem and the adjusting screw.

5.
Install the socket handle on the

9/16-inch socket.

6. Insert the T-handle extension

through the socket handle and socket,

and install the screwdriver socket on

the T-handle extension.

7.
Place the tool on the adjusting

screw so that the screwdriver socket

engages the screw and the 9/16-inch

socket engages the lock nut.

8. With a torque wrench on the T-

handle extension, tighten the adjusting

screw to 10 in-lbs torque.

9. Remove the spacer and tighten

the adjusting screw an additional 3/4

turn. Hold the adjusting screw station-

ary, and torque the lock nut to speci-

fication.

10.
Place a new gasket on the pan,

and install the screen and pan on the

transmission.

11.
Fill the transmission with fluid.

REAR BAND ADJUSTMENT—

FORD-METEOR

1.
Fold back the floor mat to ex-

pose the right side of the floor pan.

2.
Remove the access hole cover

from the floor pan. Remove all dirt

from the adjusting screw threads, then

oil the threads.

3.
Loosen the rear band adjusting

screw lock nut with the tool shown in

Fig. 13. Using the T-handle portion of

the tool, tighten the adjusting screw

until the wrench overruns.procarmanuals.com

07-03-10
FMX Transmission
07-03-10

Too/-T69P-7B793-A

ADJUSTING SCREW

REAR SERVO \ LOCK NUT

Tool—7795-C
D1329-A

FIG. 13—Adjusting Rear Band—

Ford-Meteor

If
the
screw
is
found
to be
tighter

than
wrench
capacity
(10
ft-lbs
tor-

que),
loosen
the
screw
and
tighten

until
the
wrench
overruns.

4.
Back off the adjusting screw 1

1/2 turns. Hold the adjusting screw

stationary, and tighten the adjusting

screw lock nut to specifications.

Severe damage may result if the ad-

justing screw is not backed off exactly

1 1/2 turns.

ALTERNATE REAR BAND

ADJUSTMENT—

FORD-METEOR

The tool shown in Fig. 12 may be

used to adjust the rear band.

1.
Place the socket holder on the

3/4-inch socket (Fig. 12). Insert the

T-handle extension through the handle

and socket.

2.
Place the 5/ 16-inch 8-point sock-

et on the extension. Place a torque

wrench on the T-handle extension.

3.
Insert the assembled tool in the

access hole so that it engages the ad-

justing screw and the lock nut.

4.
Loosen the adjusting screw lock

nut.

5.
Torque the adjusting screw to 10

ft-lbs.

6. Remove the torque wrench from

the T-handle extension and back off

the adjusting screw exactly 1 1/2

turns.
Severe
damage
may
result
to

the
transmission
if the
adjusting
screw

is
not
backed
off
exactly
11/2
turns.

7.
Hold the adjusting screw station-

ary and tighten the lock nut securely.

REAR BAND ADJUSTMENT—

FAIRLANE, MONTEGO

MUSTANG AND COUGAR

Adjustment of the rear band may

be performed either internally or ex-

ternally. Use the internal band adjust-

ment procedures when making a nor-

mal (in-vehicle) band adjustment. Use
ADJUSTING SCREW

LOCK NUT
I
IN

TorqueWrench REAR SERVO APPLY LEVER

D2028-A

FIG. 14—Adjusting Rear Band—

Fairlane, Montego, Mustang and

Cougar

the external adjustment procedure

only when the transmission has been

removed from the vehicle, or when all

available internal adjustment has been

taken up and a further band adjust-

ment is required.

Internal Band Adjustment

1.
Drain the fluid from the trans-

mission. If the same fluid is to be

used again in the transmission after

the band adjustment, filter the fluid

through a 100-mesh screen as it drains

from the transmission. Re-use the

fluid only if it is in good condition.

2.
Remove and thoroughly clean

the pan and filter. Discard the pan

gasket.

3.
Loosen the rear servo adjusting

screw lock nut.

4.
Pull the adjusting screw end of

the actuating lever away from the

servo body, and insert the spacer tool

shown in Fig. 14 between the servo

accumulator piston and the adjusting

screw.
Be
sure
the
flat
surfaces
of the

tool
are
positioned
squarely
between

the
adjusting
screw
and the
accumula-

tor
piston.
The
tool must
not
touch

the servo
piston
and the
tool
handle

must
not
touch
the
servo
piston
spring

retainer.

5.
Using a torque wrench with an

Allen head socket (Fig. 14), tighten

the adjusting screw to 24 in-lbs tor-

que.

6. Back off the adjusting screw

1-1/2 turns. Hold the adjusting screw

stationary and tighten the adjusting

screw lock nut sequrely. Remove the

spacer tool.

7.
Install the transmission fluid fil-

ter and clip. Install the pan using a

new gasket.

8. Fill the transmission with fluid.
D2029-A

FIG. 15—Rear Servo Lever

Adjusting Screw Dimension—

Fairlane, Montego, Mustang and

Cougar

External Band Adjustment

1.
With the transmission mounted

in a holding fixture, loosen the inter-

nal rear servo adjusting screw lock nut

(Fig. 15).

2.
Set the internal adjusting screw

to the dimension shown in Figure 15.

Tighten the lock nut.

3.
With the internal adjusting screw

properly adjusted, loosen the external

adjusting screw lock nut.

4.
Using a torque wrench with an

Allen head socket, tighten the adjust-

ing screw to 10 ft-lbs torque.

5.
Back off the adjusting screw

1-1/2 turns.

6. Hold the adjusting screw from

turning and torque the lock nut to

specification.

GOVERNOR REPLACEMENT

1.
Raise the vehicle so that the

transmission extension housing is ac-

cessible.

2.
Drain the fluid from the trans-

mission.

3.
Disconnect the drive shaft from

the rear axle and slide the front yoke

out of the extension housing.

4.
Disconnect the speedometer

cable from the extension housing.

5.
Remove the two bolts that secure

the extension housing to the engine

rear support.

6. Remove the nut and bolt that se-

cures the engine rear support to the

crossmember.

7.
Raise the transmission high

enough to provide clearance for the

rear mount.

8. Lift the engine rear support from

the crossmember.

9. Lower the jack until the exten-

sion housing just clears the crossmem-procarmanuals.com

07-03-11
FMX Transmission

07
03-11

GOVERNOR
COMPENSATOR

PRESSURE TUBE
MAIN CONTROL

VALVE TUBE

COUNTERWEIGHT

D 1815-A

FIG. 16—Governor Installed

ber to remove all weight from the

housing.

10.
Loosen the parking brake cable

adjustment nut enough to disconnect

the cables from the equalizer.

11.
Remove the extension housing

attaching bolts. Slide the housing off

the output shaft and remove the gas-

ket. When removing
the
extension

housing and/or governor, hold
the

output shaft
and
rear support from

moving rearward
to
prevent
the
needle

bearing
and
race from dropping
out of

location.

12.
Remove the governor to coun-

terweight attaching screws. Lift the

governor from the counterweight (Fig.

16).

13.
Lubricate the governor valve

parts with clean transmission fluid.

Make certain that
the
valve moves

freely
in the
valve body bore.

14.
Position the governor valve

body on the counterweight with the

cover facing toward the front of the

vehicle. Install and tighten the two at-

taching screws to the specified torque.

15.
Position a new extension hous-

ing gasket on the rear of the transmis-

sion case.

16.
Slide the extension housing into

place and secure it to the transmission

case with the attaching bolts. Torque

the bolts to specification. With the ex-

tension housing installed, rotate
the

output shaft.
The
shaft must rotate

freely
by
hand.
If the
shaft
is
tight
or

bound
up, it is
likely that
the
needle

bearing
and
race have dropped
out of

location,
in
which case,
the
transmis-

sion must
be
partially disassembled

and
the
bearing
and
race repositioned.

17.
Connect the speedometer cable

to the extension housing.

18.
Raise the transmission high

enough with a jack to position the en-
FRONT SERVO

FLUID TUBES

PRESSURE

REGULATOR

D 1817-A

FIG. 17—Typical Hydraulic Control System

gine rear support on the crossmember.

Secure the support to the crossmem-

ber with attaching bolt.

19.
Lower the transmission and re-

move the jack. Secure the extension

housing to the rear support with the

two attaching bolts.

20.
Connect the parking brake

cables to the equalizer and adjust the

cables as required.

21.
Install the driveshaft.

22.
Fill the transmission to the cor-

rect level with the specified fluid.

OIL
PAN AND
CONTROL

VALVE BODY REPLACEMENT

1. Raise the vehicle so that the

transmission fluid pan is accessible.

2.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Remove the

pan and gasket. Discard the gasket. If

the same fluid is to be used again in

the transmission, filter the fluid

through a 100-mesh screen before in-

stalling it in the transmission. Re-use

the fluid only if it is in good condi-

tion.
3.
Disconnect the hose from the

vacuum diaphragm unit. Remove the

diaphragm unit using tool FCO-24.

Do
not use any
tools
on the dia-

phragm housing, such
as
pliers, pipe

wrenches,
etc. Do not
allow solvents

to enter
the
diaphragm unit. Remove

the push rod. Remove the fluid screen

retaining clip and the screen.

4.
Remove the fluid filter retaining

clip and the filter.

5.
Remove the two tubes which

connect to the pressure regulator and

the control valve body (Fig. 17).

6. Loosen the front servo attaching

bolts three turns.

7.
Remove the three control valve

body attaching bolts, and lower the

valve body while pulling it off the

front servo tubes. Be carefull not to

damage
the
valve body
or the
tubes.

8.
Before installing the control

valve body, check for a bent manual

valve by rolling it on a flat surface.

9. Install the control valve body by

aligning the front servo tubes with the

holes in the valve body. Shift the man-

ual lever to the 1 detent, and place the

inner downshift lever between the

downshift lever stop and the downshift

valve.
The
manual valve must engage

the actuating
pin in the
manual detent

lever.

10.
Install but do not tighten, the

control valve body attaching bolts.procarmanuals.com