1967 CHEVROLET CAMARO drain bolt

FUEL TANK
AND
EXHAUST SYSTEMS
8-18

CORVETTE

FUEL TANK

INDEX

Page

General Description.
. 8-18

Service Operations
8-18

Fuel Tank
8-18

Gauge Sending Unit
8-20

Fuel Lines.
8-20

GENERAL DESCRIPTION

20 GALLON TANK

Fig.
21
—Corvette Fuel Tanks

The Corvette
is
equipped with
a
standard
20
gallon

(approx.) tank
or an RPO 36
gallon (approx.) fiberglass

tank
(fig. 21). The
tanks
are
installed
at the
very rear

of
the
vehicle, convenient
for
direct fuel filling into
the

tank.
The
tanks
are
held
in
place
by
two metal straps
at-

tached individually
to a
removable
gas
tank frame
sup-

port.
Two
guides
at the end of
the straps
are
adjustable

for securing
the
straps onto
the
tank support. The tank

support
is
secured
to the
frame rail with flat washers,

lockwashers, bolts
and
nuts.
The
tanks' rest
on six
felt

anti-squeak pads.
One pad
centers
on the
rear frame

crossmember
and one at
each side
on the
same cross-

member.
At the
same rear location two pads
are
placed

on
the
tank
at the
metal support strap (rear) attachment
location
and
another anti-squeak
pad
cemented
on the

support
at
the front
of
the tank.

The fuel tanks
are
equipped with
a gas
gauge metering

unit,
a
fuel pickup, fuel strainer
and
vent line.
If it be-

comes necessary,
the
tank
can be
completely drained
by

removing
the
fuel pickup hose which
is
located
at
the
bot-

tom
of the
tank,
or
by removing the metering
for
quicker

draining.

A pressure vacuum type, positive vented design
cap,

conforming
to
I.C.C. regulations,
is
used on both regular

production
and
optional fuel tanks.
The cap is
inter-

changeable with past model tanks
for
service replace-

ment purposes.

SERVICE OPERATIONS

FUEL TANK

CAUTION:
IF THE GAS
TANK SHOULD
BE

REMOVED
AND
INSTALLED, CARE SHOULD

BE EXERCISED
TO
AVOID PUNCTURING,

DROPPING
OR
DENTING
THE GAS
TANK.

Removal
(20
Gallon Tank)

WARNING: FIRST REMOVE BATTERY

CABLE.
1.
Remove
the
spare tire from tire carrier.

2.
Remove spare tire carrier bolted attachments
and

carrier
(fig. 22).

3.
Remove
the "U"
bolt attachments
at
both rear tail

pipe
(See
Figure
23).

4.
Separate
the
exhaust system
at
the transmission sup-

port crossmember
by
loosening
the "U"
bolt nuts.

5. Remove both rear muffler brackets from
the
frame

and slide
the
muffler system rearward.

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-19

Fig.
22—Spare Tire Carrier Installed

6. Remove two fuel tank retaining strap bottom nuts

from forward support member located at forward

front side of tank.

7. Remove fuel tank metering unit wires (fig. 25).

8. Remove fuel pickup line and drain tank.

9. Remove gas cap, filler neck boot from the top of tank

and disconnect drain line (fig. 24).

NOTE:6
Coupe Models—Remove filler neck.

10.
Remove fuel tank support frame attachment bolts and

support.

11.
Lower tank and rotate toward the front of vehicle.

Installation (20 Gallon Tank)

NOTE:
Place hoses and wires to one side and

position anti-squeak pads to the crossmember,
END OF HOSE FLUSH

TO Va INCH BACK FROM

EDGE OF BUMPERETTE

Fig.
24-Gas Tank Filler Neck Vent Hose

cemented to the support and attached to the tank.

Replace with new pads as required.

1.
Hook retaining straps at the rear frame crossmem-

ber. (Crimp strap ends at rear frame attachment.)

NOTE:
Make certain strap ends are hooked and

anti-squeak pads are properly positioned.

2.
Slowly rotate fuel tank into position.

CAUTION: Coupe-Install filler neck after tank

is installed.

3.
Attach fuel tank support at the frame side rails.

TANK METERING UNI

WIRE CONNECTIONS

Fig.
23—Exhaust System Tail Pipe Attachment
Fig.
25—Fuel Tank Metering Unit, Wires and Lines

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-20

4.
Attach the retaining straps with strap guide attached

to the fuel tank support, and secure with-the nut and

lockwasher assembly.

5. Connect the filler neck boot to the drain hose of the

tank and install boot around filler neck,

6. Connect the fuel pickup line, ground wire and make

certain that the fuel drain line is flush to 1/2" in-

board of the rear bumper opening.

7. Attach tank metering unit wires (fig. 25).

8. Replace fuel in tank. Replace gas cap.

9. Check for possible leaks.

10.
Reconnect the exhaust system by reversing the above

removal procedures (see "Exhaust System").

11.
Install spare tire carrier by securing the bolt

attachment.

12.
Install the spare tire in the tire carrier.

Removal (36 Gallon Tank)

1.
Remove cover (fig. 26).

2.
Disconnect hoses and drain tank and remove two

fittings at bottom of tank.

3.
Disconnect fuel and vent lines and wires at tank

(fig. 27).

4.
Remove straps.

installation (36 Gallon Tank)

Reverse removal procedure to install.

FUEL TANK METERING UNIT OR GAUGE

SENDING UNIT AND STRAINER

The fuel tank metering unit is located at the bottom of

the fuel tank. The fuel strainer is attached at the end of

the sending unit inside the tank.

Replacement (20 Gallon Tank)

1.
Follow fuel tank removal procedure through Step 2.

2.
Drain the tank. Disconnect the attaching wires.

3.
Remove metering unit with a fuel tank gauge unit

Spanner J-8950 (revised).

4.
'Remove metering unit and gasket.

CAUTION: Carefully remove unit so as not to

damage screen on the end of the pipe.

5. Clean strainer screen by blowing out with com-

pressed air.

6. Reverse procedure to install.

Replacement (36 Gallon Tank)

1.
Remove cover.

2.
Follow Steps 2 thru 6 as outlined under replacement

for 20 gallon tank.

FUEL LINES

20 Gallon Tank

The fuel lines are conveniently located along the out-

side of the right frame rail (fig. 28). The lines extend
Fig.
26—Gasoline Tank (36 Gallon) Compartment Cover

from the fuel tank pickup at the bottom of the tank, along

the rear frame crossmember to the right frame rail,

extending through the rail at the kickup area and along the

top inside edge of the frame to the fuel pump, Flexible

hoses are located at the fuel tank pickup and at the fuel

pump.

36 Gallon Tank

The 36 gallon tank fuel lines are routed from the bot-

tom of both sides of the tank to the right frame rail

(fig. 20).

Maintenance

CAUTION: Always drain gasoline from the

complete fuel system including carburetor, fuel

pump and all fuel lines and fuel tank if the vehi-

cle is to be stored for any great length of time.

This precaution will prevent accumulation~ol

gum formation and resultant poor engine

performance.

. The fuel lines should occasionally be inspected for

leaks,
kinks or dents, especially when work has been

done on the underside of car or after the car has been

traveling over rough or stone roads at higher speeds.

If evidence of dirt is found in the carburetor or fuel pump

at disassembly, the lines should be disconnected and

blown put. Check the fuel tank strainer for damage or

omission.

Fuel lines are beaded-type ends for connection to

hoses and flared ends for secure metal-to-metal line

connections.

CHEVROLET CHASSIS SERVICE MANUAL

FUEL TANK AND EXHAUST SYSTEMS 8-28

assembly is mounted on top of the tank and cannot be

removed for service without lowering the tank. The

upper filler neck assembly is routed through an opening

in the rear panel above the bumper and through the trunk

floor pan (fig. 33). The filler neck is not centered in the

rear panel but offset to the right to obtain the proper fill

rate.

The fuel pickup pipe is an integral part of the tank

meter unit^ located at the top front center of the tank. A

fine mesh screen is located at the bottom end of the fuel

pickup pipe to prevent the entrance of foreign material

into the fuel system.

Fig.
33—Filler Neck Assembly

COMPONENT PART REPLACEMENT

FUEL TANK

Draining Tank

Refer to Chevrolet page 8-2.

Removal and Installation

1.
Drain fuel tank. .'...' .

2.
Raise vehicle.

3.
Disconnect fuel pickup line, gauge wire and ground

lead from tank unit.

4.
Loosen filler neck inlet hose clamp.

5. Remove tank support strap bolts and straps, then

lower tank carefully.

6. Reverse procedure to install.

FUEL TANK GAUGE SENDING UNIT (Fig. 34)

Replacement

1.
Remove fuel tank.

2.
Remove cam lock using special Tool J-8950.

3.
Remove meter unit and rubber gasket.

CAUTION: Carefully remove unit so as not to

damage screen on end of pipe.

4.
Clean screen by blowing out with compressed air.

5. Reverse removal procedure to install.
FUEL LINES (Fig. 35)

The gasoline lines extending from fuel tank to fuel

pump,
are routed on the underside of the underbody, on

the right side, opposite the single exhaust system. The

lines extend from the fuel tank to the right side of the

engine to the fuel pump and over the front of the engine

to the carburetor.

Maintenance

CAUTION:

plete fuel
Always drain gasoline from corn-

including carburetor, fuel

pump and
fuel lines and fuel tank if the

vehicle is to be stored for any
eciable

length of time. This precaution will prevent

accumulation of gum formation and resultant

poor engine performance.

The fuel lines should occasionally be inspected for

leaks,
kinks, or dents. If evidence of dirt is found in the

carburetor or fuel pump disassembly, the lines should be

disconnected and blown out. Check the fuel tank strainer

for damage or omission. Fuel lines are of 5/16" diameter

tubing for regular installation with beaded-type ends for

connections to hoses and flared ends for secure line

connections.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-37

NUT

Fig.
69—Control Valve Ball Stud Seal Replacement

(Service Type)

4.
Center the ball stud, seal and clamp at opening in

adapter housing, then install spacer, bolt and nut.

Removal

1.
Raise the front of the vehicle off the floor and place

it on stands.

2.
Remove the relay rod to control valve clamp bolt.

3.
Disconnect the two pump to control valve hose cdn-

nections and allow fluid to drain into a container,
then disconnect the two remaining valve to power

cylinder hoses.

4.
Remove the retaining nut from the ball stud to pitman

arm connection and disconnect the control valve

from the pitman arm.

5. Turn the pitman arm to the right clear of the control

valve and unscrew the control valve from the relay

rod.

6. Remove the control valve from the vehicle.

Installation

1.
Install the control valve on the vehicle by reversing

the removal procedure.

2.
Reconnect the hydraulic lines, fill the system with

fluid and bleed out air using the procedure outlined

under "Maintenance and Adjustments/' Grease ball

joint.

POWER CYLINDER (Fig. 70)

Chevy II and Corvette

Removal

1.
Disconnect the two hydraulic lines connected to the

power cylinder and drain fluid into a container. Do

not reuse.

2.
Remove cotter pin, nut, retainer and grommet from

power cylinder rod attached to the frame bracket.

3.
Also remove grommet and retainer from bracket if

replacement parts are required.

1.
Snap Ring

2.
End Plug and

Lube Fitting

3.
"O" Ring
Fig.
70—Power Cylinder—Exploded View

4.
Spring

5. Spring Seat

6. Ball Stud
7. Ball Seat

8. Ball Stud Seal

9. Piston Body
10.
Piston Rod Seal

11.
Backup Washer

•12.
Scraper Element
13.
Piston Rod Scraper

14.
Snap Ring

15.
Piston Rod

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY
AND
CHASSIS
12-26

•
Low oil
pressure

• High engine temperature

• Defective wiring
or
switch

connector from sender

in block above starter
on

and
at
left front
of
distributor
on V-8
Sending Unit Replacement

1.
Disconnect wiring harness

unit terminal (located

L-6 engines

engines).

2.
Remove sender unit using Tool J-21757
or 12
point

socket, replace with
new
unit
and
check operation.

GENERATOR INDICATOR

1.
Ignition
on,
Engine
not
Running
and
Telltale Light

Off.

• Indicator bulb burned out, replace bulb.

• Open circuit
or
loose connection
in the
telltale

light circuit.

2.
telltale Light Stays
on
after Engine
is
Started.
If indicator light does
not go out at
engine idle

speed, refer
to
Charging Systems under Engine

Electrical, Section
6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists
of two re-

motely located units, indicator gauge
and
engine sender

unit.
The
indicator gauge, located
in the
instrument

panel, consists
of a
red light which will indicate
an
over-

heated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system
to a
level below unit.

2.
Remove sender unit (located
in the
inlet manifold

near water pump housing
on V-8
engines and
in the

cylinder head near
an
exhaust port
oh L-6
engines)

and replace with new unit.

3.
Refill cooling system
and
check operation
of
unit.

CHEVELLE INSTRUMENTS AND GAUGES

INDEX

Page

General Description
* *
i2-26

Service Operations
12-26

Instrument Panel
12-26

Instrument Cluster.
12-26

Fuel Gauge and/or Ammeter
12-27

Clock,
i 12-27

Speedometer
12-27
Page

Speedometer Cable
.
. 12-27

Temperature Gauge
12-29

Oil Pressure Gauge
12-29

Indicator Lights.
. 12-29

Oil Pressure Indicator
12-29

Generator Indicator
. . 12-29

• Temperature Indicator
12-29

GENERAL DESCRIPTION

The Chevelle instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator,
an
engine
tem-

perature and an
oil
pressure indicator lamp, and includes

a clock
on
deluxe models.
On
super sport models,
am-

meter, coolant temperature
and oil
pressure gauges
re-

place
the
appropriate indicator lights. Except
for the

speedometer,
all of the
indicator lamps, instruments
and

gauges
of
these clusters may
be
serviced without remov-

ing
the
instrument cluster assembly from
the
vehicle.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to the
parking
brake
and
brake pressure differential switches
and

serves
a
dual function.
It
lights when the parking brake

is applied
and
also when
the
brake pedal
is
applied,
if a

malfunction should occur
in the
brake system
due to a

loss
of
hydraulic pressure. Servicing
of the
hydraulic

pressure differential switch
is
covered
in
Section
5 of

this manual.

Regular maintenance
is not
required on the instrument

cjLuster
or its
components other than maintaining dean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL ASSEMBLY

INSTRUMENT CLUSTER (Figs.
41
thru
44)

Removal

1.
Disconnect battery ground cable.

2.
Remove steering coupling bolt and disconnect steer-

ing shaft from coupling.

3.
Loosen mast jacket lower clamp.

4.
Remove
air
conditioning center distributor duct
(if

so equipped).

5. Remove radio rear support bracket screw.

6. Remove mast jacket upper support clamp and retain-

ing bolts from lower support (refer
to
Section
9,

Steering).
CAUTION: Cover mast jacket
and
parl

brake handle with
a
suitable material
to
prevc

scratching.

7.
Disconnect speedometer cable
at
rear
of
cluster

housing
and
speed warning control knob
at
panel
(if

so equipped).

8. Remove instrument panel retaining screws (nine

upper and five lower).
.

9. Working under the console remove four lower retain-

ing screws from instrument cluster housing.

10.
Pull instrument panel assembly from console and
lay

forward on mast jacket.

11.
Disconnect wiring harness, cluster lamps and wiring

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 13

RADIATOR AND GRILLE

INDEX

Page Page

General Description 13-1 Repairs 13-4

Radiator and Shroud-All Vehicles (Except Corvette) . . . . 13-1 Installation 13-4

Removal 13-1 Grille Assembly - Chevy II 13-4

Installation 13-1 Removal . 13-4

Radiator and Fan Shroud - Corvette . . . . 13-1 Repairs 13-5

Fan Shroud Replacement 13-1 Installation . 13-5

Aluminum Radiator 13-1 Grille Assembly - Corvette 13-5

Copper Radiator . 13-1 Removal . . . . 13-5

Grille Assembly - Chevrolet 13-2 Installation ....*... 13-5

Removal 13-2 Grille Assembly - Caxnaro 13-5

Repairs 13-3 Removal 13-5

Installation 13-3 Repairs . 13-6

Grille Assembly - Chevelle 13-3 Installation . . 13-6

Removal 13-.Q

GENERAL DESCRIPTION

Radiator assemblies are attached by cap screws either the radiator and shroud are basically the same for each

to the radiator support or radiator shroud, depending on vehicle,

the engine installation of each vehicle. The Camaro fan

Shroud is mounted in two bottom slots and secured by one NOTE: Refer to the Fisher Body Service Man-

bolt at the top. Removal and installation procedures for ual for Body, Section IX for Sheet Metal, Section

14 for Bumpers, and Section 1A for Air Condi-

tioning information when required.

SERVICE OPERATIONS

RADIATOR
AND
SHROUD—ALL VEHICLES
NOTE: Reach upper two shroud bolts from top,

(EXCEPT CORVETTE)
between hood and radiator support. Reach lower

4 by reaching around front edge of open hood.

Removal

1.
Drain radiator. 4.- Remove shroud carefully (tilt rearward, then lift up

2.
Disconnect inlet and outlet radiator hoses, and Pow- to clear fan blades).

erglide cooler lines if vehicle is so equipped. 5. Reverse procedure to install, fill cooling system and

3.
Remove radiator and shroud attaching screws and lift check for leaks.

radiator and shroud out of vehicle.

Aluminum Radiator

Installation

NOTE:
Refer to Figures 1 through 5 for radi- Removal and Installation

ator fan and shroud assembled positions for each 1. Remove shroud as previously outlined.

vehicle. Reverse removal procedures, fill cool- 2. Disconnect lower raciiator hose at either end.

ing system and check for leaks. 3. Remove radiator upper mount bracket bolts and

bracket, then lift radiator from vehicle.

RADIATOR AND FAN SHROUD-CORVETTE 4. Reverse procedure to install.

Fan Shroud Replacement (Fig. 4) Copper Radiator

1.
Drain radiator and open hood. (Install a bolt in hole

of hood support bracket for safety purposes.) Removal and Installation

2.
Disconnect upper radiator hose and supply tank hose 1. Remove hood panel assembly after scribing bracket

at radiator connection. location.

3.
Remove shroud bolts. 2. Drain radiator and disconnect radiator hoses.

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS 17

TRANSMISSION AND CLUTCH

SECTION 7

THREE SPEED (SAGINAW)

Clutch Gear Retainer to Case Bolts 22 ft lbs.

Side Cover to Case Bolts . . 22 ft lbs.

Extension to Case Bolts (except overdrive) . . . . 45 ft lbs.

Overdrive Attaching Lower Left Hand Bolt (Marked X) . 30 ft lbs.

Shift Lever to Shifter Shaft Bolts 20 ft lbs.

Lubrication Filler Plug . . . . 15 ft lbs.

Transmission Case to Clutch Housing Bolts 55 ft lbs.

Crossmember to Frame Nuts . . • 25 ft lbs.

Crossmember to Mount and Mount to Extension Bolts 40 ft lbs.

THREE SPEED (WARNER)

Clutch Gear Retainer to Case Bolts . t . . . 20 ft lbs.

Side Cover to Case Bolts 20 ft lbs.

Extension to Case Bolts . . 40 ft lbs.

Shift Lever to Shifter Shaft Nut 25 ft lbsi

Lubrication Filler and Drain Plugs 20 ft lbs.

Transmission Case to Clutch Housing Bolts 55 ft lbs.

Crossmember to Frame Nuts 25 ft lbs.

Crossmember to Mount Bolts 40 ft lbs.

FOUR SPEED (SAGINAW)

Clutch Gear Retainer to Case Bolts 22 ft lbs.

Side Cover to Case Bolts 22 ft lbs.

Extension to Case Bolts (except overdrive) ' . : 45 ft lbs.

Shift Lever to Shifter Shaft Bolts 20 ft lbs.

Lubrication Filler Plug . 15 ft lbs.

Transmission Case to Clutch Housing Bolts . 55 ft lbs.

Crossmember to Frame Nuts 25 ft lbs.

Crossmember to Mount and Mount to Extension Bolts 40 ft lbs.

FOUR SPEED (MUNCIE)

Clutch Gear Bearing Retainer to Case Bolts 25 ft lbs.

Cover to Case Bolts . 20 ft lbs.

Extension and Retainer tp Case Bolts-(Upper) . 20 ft lbs.

-(Lower) 30 ft lbs.

Lubrication Filler Plug J 30 ft lbs.

Shift Lever to Shifter Shaft Nut 20 ft lbs.

CHEVROLET CHASSIS SERVICE MANUAL