1967 CHEVROLET CAMARO air condition

HEATER AND AIR CONDITIONING 1A-14

Fig.
21—Four-Season System Components (Chevrolet)

Fig.
22—Four-Season System Components (Chevelle)

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-15

Fig.
23—Four-Season System Components (Camaro)

EVAPORATOR

CORE

DEFROSTER

OUTLET DEFROSTER DOOR

V

HEATER

OUTLET

COOLED AIR OUTLETS

Fig.
24—Airflow—Four-Season (Chevrolet, Camaro) Comfortron (Chevrolet)

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-16

EVAPORATOR

CORE

\

BLOWER AND AIR I

INLET ASSEMBLY •

AIR

DOOR

OUTSIDE AIR FROM COWL VENT

DEFROSTER

DUCT

DEFROSTER

DOOR

COOLED AIR

OUTLETS

Fig.
25—Airflow—Four-Season (Cheyelie)

will be hot at all times. When, during cooling operations,

the air is cooled by the evaporator to below comfort

level, it is then warmed by the heater to the desired

temperature; during "heating only" operations the evap-

orator will not be in operation and ambient air will be

warmed to the desired level in the same manner. The

side dash outlets may be rotated to provide either soft,

diffused airflow or spot cooling. Rotate half way to shut

off airflow. The barrel type outlet in the center of the

dash will direct air up or down or, if desired, shut it off.

Controls

Four-Season System (Chevrolet, Camaro)

Full control of the Four-Season System is obtained

through the use of a single control panel (fig. 26). The

control knobs make use of bowden cables to activate the
various doors and switches necessary for system opera-

tion.
Therefore, control adjustment is a matter of

properly setting these bowden cables. The following

paragraphs explain each control.

Temperature Lever

The TEMPERATURE lever controls temperature door

position, compressor operation, and air selector door

position. When the lever is in the OFF position, the sys-

tem is totally inoperative; airflow is shut off, the fan

switch will not operate the blower, and the compressor

is off. In the VENT position, the air selector door is in

the "outside air" position and the blower is powered at

low speed. At any lever position other than OFF, the

blower will be powered at low, however, blower speed

may be increased by moving the FAN switch. When the

Fig.
26—Chevrolet Four-Season Controls
Fig.
27—CheveNe Four-Season Controls

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-17

i

c

Fig.
28—Comfortron Underdash Components

lever is above and slightly left of the COLD position, the

compressor is on, the air selector door is in the re-

circulation position, the temperature door is in the fully

cold position, and the blower is operating. Moving the

lever slightly to the right of COLD moves the air selector

door to the full outside air position while temperature

door, compressor, and blower functions remain the same

as in the "recirculating - COLD" system operation.

Moving the TEMPERATURE lever further to the right

moves the temperature door which channels some air

through the heater core. At a point about midway between

COLD and HOT, the compressor clutch switch opens and

the system is operating as a heater only with untreated

outside air (passing through the inoperative evaporator

core) mixing with heated outside air. With the lever in

the HOT position, all air (outside air) passes through the

heater core for full heat output.

Outlets and Defroster Levers

While the TEMPERATURE lever is in any operating

position, the OUTLETS and DEFROSTER levers may be

operated as desired. The OUTLETS lever directs the air

to either the heater outlet, both heater and dash outlets,

or to the dash outlets only. The DEFROSTER lever

directs air (which is flowing to the heater outlet) up to

the defroster outlets. With the DEFROSTER lever, in

the OFF position, a fixed bleed permits a small quantity
of air to flow to the defroster outlets while the major

volume of air flows from the heater floor distributor.

In the DEFROST position, airflow is split between the

heater and defroster outlets. In the DE ICE position, all

air is diverted to the defroster outlets. Since the air

must be in the heater duct in order to be directed by the

defroster door, the OUTLETS lever must be in LOWER

position which causes air to flow out the lower outlets,

if the OUTLETS lever is in the UPPER position, de-

froster door movement will have no effect on the system.

Fan Switch

The fan switch controls the operation of the three

speed blower motor except when the TEMPERATURE

lever is in the OFF position.

Four-Season System (Chevelle)

Full control of the Chevelle Four-Season is obtained

through the use of a single control panel (fig. 27) much

the same as that previously described for the Chevrolet

Four Season System. The Chevelle control differs in

operation only in that AIR and TEMPERATURE are sep-

arate controls rather than a combination control as in the

Chevrolet control panel. Except for this difference,

operation of the levers is similar to the Chevrolet

controls.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-18

HIGH BLOWER

i DELAY RELAY

AMBIENT-SUN

SENSOR AND

COMPRESSOR SWITCH

Fig. 29—Comfortron Engine Compartment Components

COMFORTRON SYSTEM

The Chevrolet Comfortron Air Conditioning System is

basically the same as the Chevrolet Four-Season system

but with the additional feature of completely automatic

control. See Figures 28, 29 and 30 for views of the

Comfortron system. To the customer, the most notice-

able difference between the two systems, will be in the

control panel. In place of the three-lever/one-switch

panel of the Four-Season system, the Comfortron has a

single control lever plus a temperature dial similar to

that found in a home thermostat. After the dial is set to

the desired temperature indication and the lever is moved

to place the system in operation, the Comfortron will

automatically control the heating and air conditioning

functions to maintain the selected interior temperature

regardless of changes in outside air temperatures.

Most Comfortron parts are located in the passenger

compartment, (fig. 28)

Jn-Car Sensor

The function of the in-car sensor is to determine the

temperature of the interior of the automobile. It is

located beneath the overhang of the instrument panel.

Feedback Potentiometer

The feedback potentiometer indicates to the amplifier

system the position of the temperature door.
Control Head

A thumb wheel is provided to select the desired in-car

temperature. A control lever performs the following

functions:

1.
Operates a switch that allows the customer to select

the type of blower program desired.

2.
Operates the control head vacuum switch except

when the TEMPERATURE lever is in the OFF

position, thus programming the vacuum system.

3.
Operates the defroster through the control head

vacuum switch. The defroster door is partially

opened in the "DE FOG" position, and fully open in

the "DE ICE" position.

A two transistor amplifier is located on the bottom

side of the control head. It receives information from

the sensors, and in turn operates the transducer.

Fig. 30—Comfortron Control

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-19

Transducer

The transducer will produce a vacuum output that is

completely adjustable by varying the input voltage which

is provided by the amplifier. An increase in the applied

voltage results in a reduced vacuum output.

Power Servo

The power servo receives a vacuum signal from the

transducer, and it is capable of assuming any position

that is called for by the sensors, amplifier, and trans-

ducer. The power servo performs the following functions:

1.
Positions the temperature mix door via the tern-

perature door link. The position of this door~"de-

termihes the portions of hot and cold air being

blended and discharged into the car.

2.
Operates the power servo vacuum valve which de-

termines the air flow paths for heating and air

conditioning.

3.
Contains a printed circuit board which controls the

blower speed. The power servo position determines

the blower speed, but the control lever switch can

override the blower program depending upon the

customer's preference.

4.
Contains the "Hi" blower delay thermistor and the

"master delay thermistor".

Outside Air Diaphragm

When there is no vacuum applied to the hose, the out-

side air door is closed under spring tension. With the

door closed, air is taken from the inside of the auto-

mobile and re-circulated. Applying vacuum to the dia-

phragm opens the door for outside air.

Mode Door Diaphragm

Located behind the duct work, the mode door diaphragm

directs the air flow out either the air conditioning outlets,

the heater floor outlet, or both the heater and air con-

ditioning outlets. This is a push-pull type diaphragm

actuated by vacuum through two hoses and controlled by

the power servo vacuum switch.

Defroster Door

The defroster door is in the defog position until vacuum

is applied to the actuator to obtain either full heat or full

de-ice position.

High Blower Delay Thermistor

The high blower delay thermistor is located on the

power servo housing under the power servo vacuum valve

and printed circuit board assemblies. The function of the

thermistor is to operate the blower at a reduced speed

when the control is in the HI FRONT position until the

residual cold air is discharged from the duct work. This

function occurs when the blower first comes "on" in cold

weather.

Vacuum Tank

During heavy acceleration, the vacuum supply from
the carburetor drops. The vacuum tank, using a^ check

valve, stores vacuum so that under these conditions

vacuum will be available for the Comfortron.

Thermal Vacuum Valve (Hot Water Vacuum Switch)

When engine coolant temperature reaches 75°F, the

valve opens and supplies vacuum to the outside air door

if the system is calling for outside air.

Master Delay Thermister

This thermistor delays the initial operation of the

blower when the system is in the heat mode. In cold

weather this allows outside ram air to flow through the

system thereby purging the cold air in the ducts gradually

until the coolant reaches about 105°F. Then, the termis-

tor passes enough current to energize the master delay

relay which powers the blower at about nine volts.

Vacuum Relay Valve

This relay valve will shut off transducer vacuum to the

power servo whenever the vacuum from the engine intake

manifold falls below the vacuum in the power servo

supply line (engine stopped or operating at low manifold

vacuum). This causes the power servo to be held in

position when the vacuum supply falls too low to maintain

servo control.

Vacuum Bleeder

A vacuum bleeder insures that the outside air door will

close (diaphragm will bleed down) after the system has

been shut down. This prevents outside air from entering

when starting the system on a cold day before the engine

coolant temperature reaches 75°F.

Sun—Ambient Sensor

The sun-ambient sensor measures the temperature of

the air entering the air intake grille in front of the wind-

shield. The sensor is exposed to sun light so that it can

lower the in-car temperature slightly when the sun

is shining.

Ambient Switch

The ambient switch operates the air conditioning com-

pressor clutch. When the outside temperature is above

40° F. the switch will be closed and the compressor will

be running. This switch is included as| part of the sun-

ambient sensor assembly, but operates independently.

Resistor Assembly

The blower resistors are located in the evaporator

housing. The printed circuit board switch in the power

servo determines which of the resistors is being used,

and as in conventional systems, the resistors control the

blower speed.

System Operation

When starting the Comfortron System in cold weather,

the following sequence of events occurs:

1.
Initially the system is inoperative. In LO FRONT

position the master delay thermistor is warming

(self-heating because current is flowing through it)

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-20

and its resistance is decreasing. In the HI FRONT

position, two thermistors (the master delay and high

blower delay thermistors) are warming. The air

door is in recirculation position until the engine

coolant reaches 75 degrees.

2.
The coolant reaches then 75 degrees and the thermal

vacuum valve opens applying vacuum to the air door

to admit outside air (unless the temperature dial is

set for cooling). Ram air will flow through the sys-

tem when the car is moving.

3.
Next, the master delay thermistor attains the tem-

perature at which it will pass sufficient current to

close the circuit through the master delay relay.

The relay circuit powers the blower motor at 9 volts.

4.
If the control is in the HI FRONT position, the high

blower delay thermistor will close the circuit

through the high blower relay which supplies full

available voltage to the blower motor. This function

occurs after the master delay thermistor has taken

effect because the high blower delay thermistor

uses the master delay type thermistor with a 10 ohm

1/4 watt resistor connected in
.
series. The nigh

blower delay thermistor must then warm to a higher

temperature than the master delay thermistor before

its resistance (plus that of the 10 ohm resistor)

drops enough to actuate the high blower relay.

5. If the controls are set for DE ICE, full outside air

and full voltage to the blower motor are effective

immediately regardless of temperatures or elapsed

times o

In accomplishing automatic control, the system follows

three steps to transform an electronic signal into me-

chanical energy through which the control is achieved.

Electronic Circuit

Two temperature sensors (Thermistors), and the duct

potentiometer connected in series, are located so as to

sense the temperature of the outside air, inside air and

system output air. The resistance of each sensor will

vary according to its temperature. The control head

temperature dial varies in resistance as it is adjusted by

the operator to suit his comfort requirements. The

resistance of the temperature dial control is applied

directly to the amplifier and is not in series with the

sensors and duct potentiometer. Thus temperature dif-

ferences in the sensor string plus the requirements fed

into the system by the operator cause changes in total

circuit resistance which allow a varying voltage flow

through the circuit.

Changing the Electronic Signal to Electrical Voltage

This minute voltage flow from the sensor string -

temperature dial circuit - is fed into the amplifier where

it is transformed into a usable amplifier output voltage,

the strength of which is determined by the strength of the

original amplifier input signal. This voltage is then

supplied to the transducer.

Changing the Electrical Voltage to a Vacuum Signal

Amplifier output voltage, varying according to tem-

perature requirements, is converted by the Transducer

into a modulator transducer output vacuum. This modu-

lated vacuum is applied to the Power Servo.

Changing the Vacuum Signal to Mechanical Energy

The Power Servo, controlled by the modulated Trans-
ducer output vacuum, operates the vacuum electrical and

mechanical components of the system as required to

provide automatic control of system operation.

Other major system components are mounted con-

ventionally in the engine compartment. Underhood com-

ponents and system airflow remain much the same as in

the Four-Season system except for the addition of the

automatic control provisions. The system operates on

100%
outside air, a mixture of outside and inside air, or

100%
recirculated air depending on the demands of the

system. The diaphragm operated .air selector door will

modulate outside air to the system during maximum air

conditioning requirements when the control unit is in

"Hi Front" position. Control of the blower is also com-

pletely automatic and dependent upon system demands.

Controls

The Comfortron controls the Chevrolet air conditioner

and heater in such a precise manner that the automobile

temperature remains relatively constant under all driving

conditions. By adjusting the thumb wheel on the Control

Head to any temperature desired between 65° and 85° F.

(See Figure 27) the automatic system will adjust the in-

car temperature even though the outside weather condi-

tions may vary considerably. The system will provide

maximum capacity for heating or cooling until the in-car

temperature reaches the pre-set Control Head Tempera-

ture. Where cooling is required, the system will start

immediately upon being turned "ON". During marginal

ambient temperatures the system will not always start

at the highest blower speeds of the control setting.

Therefore, occasionally the system can't be heard

starting*

Five over-riding functions are available so that special

conditions can be handled. Each Control Head function

will be discussed in detail below:

"Off" Position

In the "Off" position, the blower is turned off and the

outside air door is closed. No outside air should enter

the automobile.

"Lo Front" Position

The blower has five low to moderate speeds; Hi, M3,

M2,
M1 and Lo. The blower voltage will shift as directed

by the automatic controls. The "Lo Front" position

provides a quieter mode of automatic operation due to

reduction of blower noise.

"Hi Front" Position

The "Hi Front" position provides five high blower

speeds as called for by the automatic controls: The use

of the "Hi" blower speed results in a rapid cool down in

hot weather and rapid heating during cold weather. As

the in-car temperature approaches the temperature set-

ting on the Comfortron Control Head, the blower speed

will change, provided mild outside temperatures are

experienced. During very hot or cold weather, the blower

will reduce its speed only to the point where it is still

capable of maintaining the correct inrcar temperature.

"Rear" Position

The "Rear" position provides five high blower speeds.

The automatic controls select these speeds and blend the

discharge air to the proper temperature. By the use of

high blower speeds, increased airflow is obtained for

better rear seat passenger comfort.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-21

"De-Fog"
Position

In the event that the front windshield should require

removal of a fogging condition, the owner at his option

may direct air to the windshield. The "De-Fog" position

directs part of the air to the windshield while retaining a

certain amount through the floor outlets. The temper-

ature of the air remains the same as it was prior to the

control being placed in the "De-Fog" position. Five

blower speeds are available. The temperature of the air

and the blower speed are selected by the automatic

controls and are dependent upon the in-car temperature.

"De-Ice" Position

The "De-Ice" position provides full heat with "Hi"

blower directing the entire airflow to the windshield to

melt ice. The automatic controls are completely defeated

and as a result, full heat with "Hi" blower are the only

conditions that can be received. The system will turn on

immediately in this position even though the engine

coolant might be cold.

General Information

Three start up conditions can be achieved with

Comfortron.

Weather

Cold
Method of Starting System

System starts as soon as engine coolant is

hot.

Hot System starts immediately when AC is

required.

Any System starts immediately in "De-Ice"

position.

UNIVERSAL SYSTEM

A self-contained unit, the dealer installed Universal

System operates on recirculated air only and entirely

independent of the vehicle heater. Recirculated inside air

is drawn into the unit, passed through the evaporator core

and into the car through the adjustable outlets in the

evaporator case. The entire unit mounts compactly

beneath the dash. Temperature control is by means of a

thermostatic switch.

The compressor used with the Universal System is

identical to that used for the Four-Season system except

for displacement. Underhood components are similar in

placement to the Four-Season system.

Controls

Universal system controls are the AIR knob controlling

the three speed blower motor switch and the TEMP knob

which controls the setting of the thermostatic switchi

Switch adjustment is covered elsewhere in this section.

When operating this system the Heater must be fully off.

CHEVY II ALL-WEATHER SYSTEM

The Chevy n All-Weather Air Conditioning System,

Figure 33, operates in conjunction with the heater to

provide a complete air conditioning system operating on

either outside air, recirculated air or a combination of

both. The cooling unit attaches to the heater distributor

and utilizes the heater blower. Several controls allow
full use of either the heating or cooling features of the

system. During marginal weather, it is possible to pro-

vide heated air at floor level and cooled air at breath

level.

A schematic view of the air conditioning underdash

components is provided in Figure 34 to aid in under-

standing airflow and control operation.

The evaporator assembly, located in the passenger

compartment attached directly to the heater distributor,

contains the evaporator core, expansion valve, thermo-

static switch and the air conditioning "ON" knob. The

thermostatic switch, utilized as the cooling control, feels

the temperature of the cooled air leaving the evaporator

core and turns the compressor on and off in accordance

with cooling needs. Refrigerant lines connect the evap-

orator assembly to the other system components located

in the engine compartment.

The six cylinder air conditioning compressor, com-

pletely field serviceable, is bracket-mounted to the

engine and is belt driven from the crankshaft pulley. A

muffler assembly, designed to eliminate compressor

pulsations is an integral part of the compressor con-

nector block. The condenser is mounted on the radiator

support just ahead of the engine radiator. The receiver-

dehydrator, with its sight glass, is located on the right

fender skirt.

Controls

Control of the air conditioning system is achieved

through the use of the heater control on the instrument

panel as well as the two knobs located on the air condi-

tioning unit itself (fig. 35).

Air Conditioning "ON" Knob

Labeled "Pull for Air Cond.", this knob diverts air-

flow from the floor distributor and through the air condi-

tioning unit. Initial movement of this knob also actuates a

switch, located at the damper door, which energizes the

compressor clutch thus putting the system into operation

and under the control of the thermostatic switch.

Temp-Cool Knob

This knob controls the thermostatic switch. Turn the

knob clockwise for more cooling, counter-clockwise for

less cooling.

Air Lever

This lever actuates the damper within the assembly

which chooses between recirculated air or outside air.

Fig.
31-Universal Air Conditioning Unit

CHEVROLET CHASSIS SERVICE MANUAL