1967 CHEVROLET CAMARO wiring diagram

HEATER AND AIR CONDITIONING 1A-82

•BATTERY

(POS)
CABLE
NOTE
When
control
switch*

is !TOFF"
&
Air
Cond
is
"ON"

(Control
knob
pulled
but) the

blower
fan'will
run at low
speed.
CONTROL
SWITCH

CONNECTIONS

OFF

LOW

MED

HIGH
B
TO
NONE

B
TO L

BTOL&M

B
TO L
&
H

COMPRESSOR
GROUND

WIRE
ASM
BATTERY

(NEGATIVE)

CABLE

COMPRESSOR
ASM

DASHPAJSTEL

GROMMET

16DG
CONTROL

SWITCH

RESISTOR

ASM

14LBL

14BRN
CLUTCH

COIL

EXTENSION

WIRE
ASM
-14BRN--N

JUNC

BLOCKi

OSTATIC

SWITCH

CONTACTS

NORMALLY

CLOSED
STARTING

MOTOR

SOLENOID

BLOWER

MOTOR
AIR
COND

CONTROL

(PUSH-PULL)

KNOB

DOOR
SWITCH

(PUSH
BUTTON

NORMALLY

CLOSED)
RELAY

ASM

HORN

RELAY

DIVERTER

DOOR CABLE

FUSE

PANEL

EVAPORATOR

ASM

IGNITION SWITCH-

ACCESSORY TERMINAL)

Fig. 118—All Weather Wiring Diagram (Chevy II)

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-83

DIVERTER DOOR

CRANK POSITIONS:

AIR COND "ON"

AIR COND "OFF*
AIR COND SWITCH

(PUSH BUTTON,

NORMALLY CLOSED

CONTACTS)

BLOWER MOTOR

CONTACTS

NORMALLY

4D

16

16B/Y

COMPRESSOR

GROUND WIRE

ASM

BAT.
TERMINAL

ON STARTING

MOTOR SOLENOID

' BATTERY

CABLE ASM:

NEGATIVE

POSITIVE—*
- CONTROL SWITCH

SET AT:

•OFF

LOW

MED

HIGH
CONTACTS:

BTOBL

BTOL

BTOM

BT0M6B,

CLUTCH

HOUSING
liOli: WHEN CONTROL

SWITCH IS AT "OFF" &

AIR COND. IS "ON", FAN

WILL RUN AT LOW SPEED.

"AIR COND-PULL"

KNOB (SHOWN IN "ON"

POSITION)

TO REGULATOR

HORN

RELAY
16 BRN-BODY WIRING

HARNESS-837

14BRN

I

^
IA^RN
* IGNITION SWITCH

« 12R ACCESSORY TERMINAL

12R f

AMMETER

LEGEND:

AIR COND WIRING (PART OF

ENGINE WIRING HARNESS)

WIRING IS PART OF EQUIP

REG PRODUCTION WIRING

Fig.
119—Corvette—Four-Season Wiring Diagram

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-8

1

FIELD RELAY^I^p2

"LATCH"
^PFN?^

"P1
TERMINAL
JyJvJCTl^

NO. 2 TERMINAD^5^^^«

NO.
3 TERMINAL ^S5«£

NO.
4 TERMINAL ^^^
m

# / VOLTAGE

¥ REGULATOR

1
ACCESS PLUG TO

VOLTAGE ADJUSTMENT

No 4 TERMINAL

Double Contact

Fig.
2c—Voltage Regulator Assemblies
Transistor

regulator to handle the higher field current and enables it

to absorb the increased inductive voltages of the field

coil with satisfactory contact point life.

The double-contact regulator assembly (fig. 2c) con-

sists of a double contact voltage regulator unit and a field

relay unit. This unit uses two sets of contact points on

the voltage regulator unit to obtain desired field excita-

tion under variable conditions. Internal circuit wiring

diagrams of the double contact regulator are shown in

Figures 3c and 4c.

The transistor regulator (fig. 2c) is an assembly com-

posed principally of transistors, diodes, resistors, a

capacitor, and a thermistor to form a completely static

voltage regulating unit in combination with a conventional

vibrating type field relay.

The transistor is an electrical device which limits the
generator voltage to a preset value by controlling the

generator field current. The diodes, capacitor and re-

sistors act together to aid the transistors in controlling

the generator voltage. This is the only function that the

regulator performs in the charging circuit. The

thermistor provides a temperature-compensated voltage

setting. Wiring diagrams of the transistor regulator are

shown in Figures 3c and 4c.

The voltage at which the generator operates is deter-

mined by the regulator adjustment. The regulator voltage

setting can be adjusted externally by removing a pipe plug

in the cover (fig. 2c) and turning the adjusting arm inside

the regulator. This procedure is explained in the followr

ing section, and permits regulator adjustments without

removing the cover.

FUSIBLE

DOUBLE CONTACT
FUSIBLE LINK-^
JUNCTION HORN

BLOCK RELAY

RESISTOR

Q FIELD Q>

DELCOTRON TR-

TRANSISTOR
FUSIBLE LINK-

Fig.
3c-Circuity - Voltage Regulator Assemblies (Except Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-9

63 AMP 1

MODELS ONLY'
BATTERY FUSIBLE

LINK
HORN

FUSIBLE LINK'
TRANSISTOR
FUSIBLE LINK'

Fig.
4c— Circuitry - Voltage Regulator Assemblies (Corvette)

Engine compartment wiring harness incorporates sev-

eral fusible links. Each link is identified with its gage

size. A fusible link is a length of special wire (normally

four wire gages smaller than the circuit it is protecting)

used in wiring circuits that are not normally fused, such

as the ignition circuit. The same size wire with a hypalon

insulation must be used when replacing a fusible link.

The links are:

1.
The pigtail lead at the battery positive cable (except

Corvette) is a 14 gage, brown fusible link protecting

the 10 gage battery charging circuit. This wire is an

integral part of the battery cable assembly and serv-

icing requires replacing the complete battery cable

assembly. On Corvette models this link is installed

as a molded splice at the solenoid "Bat" terminal

and servicing requires splicing in a new link.

2.
A 16 gage black fusible link is located at the horn
4.
relay to protect all unfused wiring of 12 gage or

larger. It is installed as a molded splice and serv-

icing requires splicing in a new link.

The generator warning light and field circuitry (16

gage wire) is protected by a fusible link (20 gage

orange wire) used in the "battery feed to voltage

regulator #3 terminal" wire. The link is installed as

a molded splice in the generator and forward lamp

harness and is serviced by splicing in a new 20 gage

wire as required.

The ammeter circuit on all models is protected by

two orange, 20 gage wire fusible links installed as

molded splices in the circuit at the junction block or

the solenoid "Bat" terminal (Corvette only) and at

the horn relay. Each link is serviced by splicing in a

new 20 gage wire as required.

MAINTENANCE AND ADJUSTMENTS

At regular intervals, inspect the terminals for cor-

rosion an4 loose connections, and the wiring for frayed

insulation. Check mounting bolts for tightness. Check the

drive belt for alignment, proper tension and wear. Be-

cause of the higher inertia and load capacity of the rotor

used in A.C. generators, PROPER BELT TENSION is

more critical than on D.C. generators.

Since the Delcotron and its companion regulator are

designed for use on negative polarity systems only, the

following precautions must be observed. Failure to ob-

serve these precautions may result in serious damage to

the charging system.

1.
When installing a battery, always make absolutely

sure the ground polarity of the battery, generator and

regulator is the same.

2.
When connecting a booster battery, make certain to

connect the correct battery terminals together.

3.
When connecting a charger to the battery, connect the

correct charger leads to the battery
%
terminals.

4.
Never operate the generator on an uncontrolled open
TO SOLENOID

BAT ACC RES. WIRE

Fig.
5c—Typical Wiring Diagram Showing Lead Connections

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-13

PULL-IN

WINDING
li
HOLD-IN

WINDING

Fig.
4B -
Overdrive Electrical Circuit Wiring Diagram

ELECTRICAL

Any one of the following general complaints may be due

to electrical trouble in the overdrive circuit.

1.
Does not engage.

2.
Does not release.

3.
Does not kickdown from overdrive.

These troubles may be traced and remedied as de-

scribed in the following paragraphs.

1.
Does not engage

a. With the ignition switch on, ground the "KD" ter-

minal of the solenoid relay with a jumper lead.

If the solenoid clicks, the relay and solenoid cir-

cuits are in operating condition. If no click is

heard in the relay, check the fuse and replace if

defective.

b.
If the fuse is good, use a second jumper lead to

connect the "SOL" and "BAT" terminals of the

relay. If a click is now heard in the solenoid, the

relay is probably at fault and should be repaired

or replaced.

c. If the solenoid does not click in Step b, check the

wiring to the No. 4 terminal of the solenoid and

replace if necessary. If the wiring is not defec-

tive,
the trouble is probably in the solenoid. Re-

move the solenoid cover, examine the solenoid

contacts in series with the pull-in winding and

clean if necessary. Test again for clicks, as in

Step b, after replacing solenoid cover and lead

wires.
Replace the solenoid if trouble has not

been corrected.

d. If the relay and solenoid circuits are in good con-

dition as determined in Step a, leave the ignition

switch on and make sure the manual control knob

is in the overdrive position. Ground one and then

the other of the two terminals next to the stem of

the kickdown switch (identified as "SW" and
?fREL"). K the solenoid clicks when one terminal

is grounded but not the other, replace the switch.

If the solenoid does not click when either of the

terminals is grounded, check the wiring between

the relay and the kickdown switch and replace if

defective.

e. If the solenoid clicks as each terminal is grounded

in Step d, ground the governor switch terminal.

If the solenoid clicks, the governor switch may be

defective. If the solenoid does not click, check

the wiring between the kickdown and governor

switches and replace if necessary.

2.
Does not release

a. Remove the connection to the "KD" terminal of

the relay. If this release overdrive, look for a

grounded control circuit between the relay and

governor switch.

b.
If the overdrive is not released in Step a, dis-

connect the lead to the "SOL" terminal of relay.

If this releases the overdrive, replace the relay.

3.
Does not kickdown from overdrive

a. With the engine running, connect a jumper lead

between the No. 6 terminal of the solenoid and

ground. Operate the kickdown switch by hand.

This should stop the engine. If it does, the sole-

noid is probably defective and it should be checked

for dirty ground-out contacts or other defects

within the ground-out circuit of the solenoid (fig.

4B).
Clean the contacts or replace the contact

plate as required.

b.
If the engine does not stop in Step a, ground one

and then the other of the two terminals (Identified

as "IGN" and "SOL") farthest from the sfem of

the kickdown switch. The engine should stop when

one of the two terminals (IGN) is grounded. If

the engine does not stop when the terminal is

grounded, the wiring or connections to the switch

between the switch and coil are defective. When

the btlier terminal (SOL) is grounded, the engine

should stop when the kickdown switch is operated.

If the engine does not stop when the kickdown

switch is operated with the second terminal

grounded, the kickdown switch is defective. If

the trouble is in the kickdown switch, adjust the

linkage to give more travel of the switch rod.

If this does not correct the trouble, replace the

kickdown switch.

If the kickdown switch operates as it should,

check for an open circuit in the wiring between

the kickdown switch and the No. 6 terminal of the

solenoid.

c. If the trouble is not located by the above checks,

the upper contacts of the kickdown switch may not

be opening. To check for this condition, ground

the overdrive control circuit at the governor

switch. This should cause the solenoid to click.

Operate the kickdown switch by hand. This should

cause a second click as the solenoid releases.

If there is no second click, adjust the linkage to

give more travel of the switch rod. If this does

not correct the trouble, replace the kickdown

switch.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 12

ELECTRICAL-BODY AND CHASSIS

CONTENTS
OF
THIS
SECTION

Page
Page

System 12-1

Instruments and Gauges 12-21

Directional Signal 12r40
Windshield Wipers and Washers 12-44

Wiring Diagrams 12-56

Special Tools 12-60

LIGHTING SYSTEM

INDEX

Page

General Description
!2-i

Maintenance and Adjustments
•.................. 12-2

Headlamp Adjustment......................
12-3

Headlamp Panel Travel Adjustment.
12-5

Service Operations.
. . .. 12-5

Front Lighting
12-5

Headlamp
. 12_5

Parking Lamp
12-5

Fender Lamp
. 12_^

Headlamp Panel
12-8

Headlamp Panel Motor
^2-9

Rear Lighting
l2-10

Tail, Stop and Directional Lamps
12-10
Page

Backing Lamps
12-14

License Plate Lamp
12-14

Automatic Transmission Quadrant Lamp
12-14

Seat Separator Console Lamps
. 12-15

Lighting Switch
. . 12-15

Wiper Switch.
12-15

Stoplight Switch
12-15

Dimmer Switch
12-15

Backing Lamp Switches
12-15

Neutral Safety Switches
12-17

Parking Brake Alarm Switch
................. 12-19

Instrument Panel Compartment Lamp/Switch
12-19

Cirgarette Lighter
12-19

GENERAL DESCRIPTION

.
The lighting system includes: the main lighting switch,

stop light, dimmer, and backing lamp switches, head-

lamps, parking lamps, stop, tail and directional lamps,

instrument illumination and indicator lamps, and the

necessary wiring to complete the various circuits. A

fuse panel provides convenient power take offs and fuse

clips for the appropriate circuits (fig. 1).

Chevrolet and Chevelle headlamp installation is all

new in that the headlamps are located in the radiator

support with adjusting screws and springs. Eliminating

the need for having separate headlamp housings. Chev-

rolet and Chevelle headlamp retainers and springs are

interchangeable.

Chevy n headlamp housings are new because of revised

front end styling and Corvette front end lighting is basi-

cally carryover.

Front fender lamps have been added as an option for

Chevrolet models and as standard equipment on Caprice

series.

Camaro models use single headlamps and the Rally

Sport model headlamps are covered by a retractable

section of the grille when lamps are not used. The sec-

tion of the grille covering the headlamps folds back when

lights are required; the headlamps are stationary. The

covering is retracted by a small electric motor mounted

to the headlamp housing. The headlamps are automat-

ically uncovered when the headlight switch is pulled "ON"

for illumination. If at any time the electrical circuit

becomes inoperative, the lamps can be uncovered manu-

ally. The ignition switch must be
"ON"
in order to close

the headlamp doors.

Parking lamp for Chevelle and Chevrolet models are
new due to revised front end sheet metal and bumper

styling. Parking lamps are located in the bumper on

Chevrolet, Chevelle and Chevy n models

Camaro parking lamps are located in the radiator

grille except for the Rally Sport models on which the

parking lamps are in the valance panel. For styling

reasons, the lens is white and an amber glass bulb is

used. All Camaro parking lamps require a separate

ground wire to assure a good ground contact because of

the plastic grille and painted contact surfaces.

The Chevrolet tail, stop, and directional lamps are in

one housing with a three section lens design on Impala

and Caprice sedans. The center lens for Impala series

is the back-up lamp. The center lens on the Caprice is

a tail lamp with the back-up lamps being located in the

rear bumper. Chevrolet station wagons have three indi-

vidual housings with three lenses, the center lamp being

the back-up. Biscayne and Bel-Air sedans have a single

housing and lens for tail, stop, and directional lamp with

a similarly constructed back-up lamp inboard and adja-

cent to it.

Chevelle tail, stop, and directional lamps are a single

lens design that follows through with the rear fender

styling. The back-up lamp is located in r.ear bumper.

Camaro models except Rally Sport have tail lamps

with integral back-up lamps mounted inboard of the rear

fenders between the trunk opening and bumper. The

Rally Sport model has dual tail lamps in the rear housing

and valance mounted back-up lamps.

Corvette, Chevy n, and Corvair tail and directional

signal lights are carryover. The Corvette has new back-

up lamps center mounted above the license plate opening.

CHEVROLET CHASSIS SERVICE

ELECTRICAL-BODY AND CHASSIS 12-2

FJg.
1 - Fuse Panel Assembly

All power window and tailgate circuits require the igni-

tion switch to be "ON" to open or close the windows un-

like past model designs which were operated independ-

ently of the ignition switch.

The windshield wiper and washer switch is new in that

washer button in the center of the knob has been deleted
and its function will be accomplished by pushing the knob.

A set screw is used to retain the knob to the shaft.

In addition to fuses, the wiring harness incorporates

fusible links to protect the wiring. Links are used rather

than a fuse in wiring circuits that are not normally fused,

such as the ignition circuit. Fusible links in the Chevro-

let wiring are four gauge sizes smaller than the cable it

is designed to protect. The links are marked on the

insulation with wire gauge size because of the heavy insu-

lation which makes the link appear a heavier gauge than it

actually is.

Engine compartment wiring harness incorporate sev-

eral fusible links. Each link is identified with its gauge

size.
A fusible link is a length of special wire (normally

four wire gauges smaller than the circuit it is protecting)

used in wiring circuits that are not normally fused, such

as the ignition circuit. The same size wire with a spe-

cial hypalon insulation must be used when replacing a

fusible link.

The links are:

1.
The pigtail lead at the battery positive cable (except

Corvette) is a 14 gauge, brown fusible link protecting

the 10 gange battery charging circuit. This wire is

an integral part of the battery cable assembly and

servicing requires replacing the complete battery

cable assembly. On Corvette models this link is

installed as a molded splice at the solenoid "Bat"

terminal and servicing requires splicing in a new

link.

2.
A 16 gauge black fusible link is located at horn relay

to protect all unfused wiring of 12 gauge or larger.

It is a serviceable piece with an in-line connector

and is not integral with the wiring harness.

3.
The generator warning light and field circuitry (16

gauge wire) is protected by a fusible link (20 gauge

orange wire) used in the "battery feed to voltage

regulator #3 terminal" wire. The link is installed

as a molded splice in the generator and forward lamp

harness and is serviced by splicing in a new 20 gauge

wire as required.

4.
The ammeter circuit on all models is protected by

two orange, 20 gauge wire fusible links installed as

molded splices in the circuit at the junction block or

the solenoid "Bat" terminal (Corvette only) and at the

horn relay. Each link is serviced by splicing in a

new 20 gauge wire as required.

The wiring harnesses use a standarized. color code

common to all Chevrolet vehicles. Under the color code,

the color of the wire designates a particular circuit. The

harness title indicates the type of harness, single of mul-

tiple wire, and also describe the location of the harness.

The body harness is a flat, solid wire assembly and is

routed through the vehicle near the center of the body.

Composite wiring diagrams (figs. 104 thru 124) are in-

cluded at the end of this section.

MAINTENANCE AND ADJUSTMENTS

Maintenance of the lighting units and wiring system

consists of an occasional check to see that all wiring

connections are tight and clean, that the lighting units are

tightly mounted to provide good ground and that the head-

lamps are properly adjusted. Loose or corroded con-

nections may cause a discharged battery, difficult start-

ing, dim lights, and possible damage to generator and

regulator. Wire harnesses must be replaced if insulation

becomes burned, cracked, or deteriorated. Whenever it
is necessary to splice a wire or repair one that is bro-

ken, always use solder to bond the splice. Always use

rosin flux solder on electrical connections. Use insulat-

ing tape to cover all splices or bare wires.

When replacing wires, it is important that the correct

size be used. Never replace a wire with one of a smaller

size.

Each harness and wire must be held securely in place

by clips or other holding devices to prevent chafing or

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-3

Fig.
2 - T-3 Safety Aimer

wearing away the insulation due to vibration.

By referring to the wiring diagrams, circuits may be

tested for continuous circuit or shorts with a conventional

test lamp or low reading volt meter.

HEADLAMP ADJUSTMENT-

T-3 HEADLAMPS

CAUTION: Check and tighten radiator support

grille retaining bolts prior to attempting head-

lamp aiming. Distorted grille or supports in

this area will hinder proper aiming of head-

lamps. On Corvette models make sure head-

lamp panel is adjusted properly - refer to

"Headlamp Panel Travel Adjustment".

When aiming headlamps, vehicle should be filled to ca-

pacity with gas, oil, and water but no load. Tires should

be uniformly inflated to recommended pressure.

the T-3 Safety Aimer-Type B (fig. 2), is used for the

headlamp aiming description that follows. An adapter is

required with the Type B T-3 Aimer when adjusting the 7

inch headlamp used on the Chevy n vehicle.

1.
Drive vehicle onto selected aiming area. Bounce

vehicle several times and allow to settle.

2.
Remove headlamp bezels.

3.
Mount the T-3 Aimers on either the No. 1 or No. 2

pair of headlamps so that "the points of the headlamps

engage the smooth inner ring of the aimers.
HORIZONTAL

AIMING

SCREW

STRING OVER

"2R" ON AIMER ARM

Fig.
4—-Headlamp Horizontal Adjustment

NOTE:
In the dual headlamp installation, the

inboard unit is designated No. 1 and the outboard

unit is designated No. 2.

4.
Secure the aimers to the headlamp units by firmly

pressing knob at center of each aimer (fig. 3). Ro-

tate crossarms inboard to approximate horizontal

position.

NOTE:
Moisten suction cups slightly to obtain

maximum holding force.

5. With both aimers in place, knot both ends of elastic

string and, using slots provided, fasten string across

horizontal crossarms of each aimer.

6. Rotate both aimers so that the string just clears the

points on the crossarms.

HORIZONTAL ADJUSTMENT

7. a. Turn horizontal aiming screw, Figure 4, on left-

VERTICAL ADJUSTMENT SCREW

Fig.
3 - Installing Aimer on Headlamp Unit
Fig.
5 - Headlamp Vertical Adjustment

CHEVROLET CHASSIS SERVICE MANUAL