1967 CHEVROLET CAMARO brake light

REAR SUSPENSION AND DRIVE LINE 4-24

4

i*
5

Fig.
65—Removing Bushings (Corvette)

4.
Lightly oil new bushing diameters (not rubber por-

tion) and start bushings squarely in arm.

5. Install Tool J-7055-1 as shown in Figure 66 and

press bushings into place.

6. When bushings are fully installed, place special

plate over flared portion of new bushing retainer

and insert retainer into bushing.

7. Out of 5/8" thick steel plate 1-1/2" wide make flar-

ing tool support to the dimensions shown in Figure

67 and drill clearance holes as shown for 2
—
1/2"

bolts.

8. Place fabricated back-up plate on flared end of bush-

ing retainer and assembly Tool J-8111-23 to plate

with 2-1/2" bolts 5" long. Make sure threaded hole

in J-8111-23 is centered over unflared end of bushing

retainer and that chambered retainer plate is cen-

tered over retainer tube.

9. Lightly oil pointed end of J-8880-5 screw and thread

into J-
8111-23
until pointed "end contacts bushing

retainer. Continue threading J-8111-23 until retainer

is flared (fig. 68).

Installation

1.
Place torque arm in frame opening.

2.
Place toe-in shims in original position on both sides

of torque arm, install pivot bolt and tighten but do

not torque at this point.
Fig.
67—Flaring Tool Back-Up Plate (Corvette)

3.
Raise axle drive shaft into position and install to

drive flange. Torque bolts to specifications.

4.
Raise strut rod into position and insert strut rod

shaft so that flat lines up with flat in spindle sup-

port fork. Install nut and torque to specifications.

5. Install shock absorber lower eye and tighten nut

to specifications.

6. Connect spring end as outlined under Spring-

Bistallation, Steps 3-6'.

NOTE:
If vehicle is so equipped, connect sta-

bilizer shaft to torque arm - refer to "Sta-

bilizer Shaft Replacement".

7. Install brake disc and caliper, wheel and tire and

lower vehicle. Tighten torque arm pivot bolt. Bleed

brakes as outlined in Section 5-Brakes.

SUSPENSION CROSSMEMBER

Removal

1.
Disconnect and remove spring as outlined under

Spring-Removal.

2.
Remove differential carrier assembly as outlined

under Differential Carrier-Removal in this section.

3.
Support crossmember, remove bolts securing

crossmember isolation mounts to frame and lower

crossmember (fig. 69).

Fig.
66—Installing Bushings (Corvette)
Fig.
68—Flaring Retainer (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-31

Fig.
77—Differential Pinion Shaft Removal

AXLE SHAFT

Removal

1.
Raise vehicle to desired working height and remove

wheel and tire assembly and brake drum.

2.
Clean all dirt from area of carrier cover. *

3.
Drain lubricant from carrier by removing cover.

4.
Remove the differential pinion shaft lock screw and

the differential pinion shaft (fig. 77).

5. Push flanged end of axle shaft toward center of

vehicle and remove "C" lock from button end of

shaft.

6. Remove axle shaft from housing, being careful not

to damage oil seal.

Wheel Bolt Replacement .

Press bolts out of axle shaft flange (as illustrated in

Figure 78) and press new bolts into place, making sure

that they are tight and square with flange.

Off Seal and/or Bearing Replacement

•1.
Remove the oil seal by using the button end of the

axle shaft - insert the button end of the shaft behind

the steel case of the oil seal, then pry seal out of

bore being careful not to damage housing.

2.
Insert Tool J-8119 into bore and position it behind

bearing so that tangs on tool engage bearing outer

x race. Remove bearing, using slide hammer as shown

in Figure 79. Figure 80 shows a detail of axle

housing outer end.

3.
Lubricate new bearing with wheel bearing lubricant,

and install bearing so that it bottoms against
Fig.
79—Wheel Bearing Removal

shoulder (fig. 81). To install bearing use Tool

J-21491 for the Chevelle, Camaro and Chevy JI

light-duty axle and Tool J-21051 for all Chevrolet

models and also for Chevelle, Camaro and Chevy tl

models with heavy-duty axle.

Pack cavity between the seal lips with a high melting

point wheel bearing lubricant; position seal on tool

(Use J-21491 for the Chevelle, Camaro and Chevy II

light-duty axle and J-21051 for all Chevrolet models

and also for Chevelle, Camaro and Chevy II models

with heavy-duty axle) and position seal in axle

housing bore, tap seal into place so that it bottoms

against bearing (fig. 81).

Brake Flange Plate Replacement

1.
Remove "brake line at wheel cylinder inlet and dis-

assemble brake components from flange plate. Refer

to Section 5 for brake disassembly procedure.

2.
Remove 4 nuts securing flange plate to axle housing.

3.
Install new flange plate to axle housing and torque

nuts to specifications.

Fig.
78—Wheel Bolt Replacement
Fig.
80-Axle Housing Detail

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-32

HP?

Fig.
81
—Whed Bearing and/or Oil Seal Installation

4.
Install brake components on flange and connect

hydraulic line to wheel cylinder inlet. See Section 5

for brake assembly procedure.

5. Install axle shaft, brake drum and wheel and tire

assembly.

6. Bleed and. adjust brakes as outlined in Section 5.

Installation

1.
Slide axle shaft into place.

CAUTION: Exercise care that splines on end

of shaft do not damage oil seal and that they

engage with splines of differential side gear/

2.
Install axle shaft "C" lock on button end of axle-

shaft and push shaft outward so that shaft lock seats

in counterbore of differential side gear.

3.
Position differential pinion shaft through case and

pinions, aligning hole in shaft with lock screw hole.

Install lock screw and torque to specifications.

4.
Using a new gasket, install carrier cover and torque

bolts to specifications.

CAUTION: Make sure both gasket surfaces on

carrier and cover are clean before installing

new gasket. Torque carrier cover bolts in a

crosswise pattern to ensure uniform draw on

cover gasket.

5. Fill axle with lubricant to a level even with bottom

of filler hole. See Section 0 for proper lubricant.

6. Install brake drum and wheel and tire assembly.

7. Lower vehicle and test operation of axle.

PINION FLANGE, DUST DEFLECTOR

AND/OR OIL SEAL

Replacement

1.
Raise rear of vehicle and place stand jacks under

frame side rails so that axle hangs freely to allow

sufficient working room.

2.
Check wheels for freedom of rotation.

3.
Separate rear universal joint, tape trunnion bearings

to joint, position propeller shaft to one side and tie

it to frame side rail.

4.
Using Tool J-5853 with Adapter J-5810 and a suitable

socket on the pinion flange nut, rotate the pinion

through several complete revolutions and record the

torque required to keep the pinion turning (fig. 82).

If flange is to be reused, mark pinion and flange for

reassembly in the same relative position.

5. Install Tool J-8614-1 on pinion flange and remove

pinion flange nut and washer (fig. 83). (Position
Fig. 82—Measuring Drive Pinion Bearing Preload

J-8614-1 on flange so that the four notches are

toward flange.) Discard nut and use a new one

upon reassembly.

6. Thread pilot end of Tool J-8614-3 into small O.D.

end of J-8614-2. Then with J-8614-1 installed as

in Step 4, insert J-8614-2 into J-8614-1 and turn

it 45 degrees to locked position. Remove flange by

turning J-8614-3 while holding J-8614-1 (fig. 84).

7. Pry old seal out of bore, using a screw driver or a

hammer and chisel.

8. Inspect pinion flange for smooth oil seal surface,

worn drive splines, damaged ears, and for smooth-

ness of bearing contact surface. Replace if

necessary.

9. If deflector requires replacement, remove by tapping

from flange, clean up stake points; install new de-

flector, and stake deflector at three new equally

spaced positions.

NOTE:
Staking operation must be performed

in such a manner that the seal operating surface

is not damaged.

1.0. Pack the cavity between the seal lips of the pinion

flange oil seal with a lithium-base extreme pressure

lubricant, position seal in bore, then using Tools

J-21468 and J-9458, for light-duty axle and Tool

Fig. 83-—Drive Pinion Nut Removal

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES

SECTION 5

CONTENTS OF THIS SECTION

Duo Servo Brakes

Disc Brakes
Page

5-1 Power Brakes

5-24 Special Tools
Page

5-31

5-32

DUO-SERVO BRAKES

INDEX

Page

General Description 5-1

Maintenance and Adjustments 5-3

Hydraulic Brake Fluid .. . 5-3

Bleeding Hydraulic System 5-3

Pressure Bleeding 5-3

Manual Bleeding 5_4

Push Rod to Main Cylinder Clearance 5-5

Hydraulic Brake Lines 5-5

Hydraulic Brake Hose 5-5

Hydraulic Brake Tubing 5-6

Brake Adjustment. .................... 5-7

Service Brake 5-7

Parking Brake 5-8

Component Replacement and Repairs 5-9

Parking Brake - Chevrolet, Chevelle and

Camaro 5^9

Pedal Assembly 5-9

Front Cable ,. . . 5-9

Center Cable 5-9

Rear Cables. . 5-9
Parking Brake - Chevy n 5-9

Lever Assembly 5-9

Idler Lever 5-11

Front Cable 5-11

Rear Cable . . ; 5-12

Parking Brake - Corvette 5-13

Lever Assembly . . . . 5-13

Front Cable 5-14

Rear Cable . . 5-14

Brake Pedal 5-15

Shoes and Linings 5-16

Organic 5-16

Metallic 5-17

Main Cylinder 5-18

Wheel Cylinders 5-21

Anchor Pin 5-22

Front Wheel 5-22

Rear Wheel 5-22

Brake Drums • 5-22

Brake Pipe Distribution and Switch Assembly . . . . . 5-23

Camaro Pressure Regulator Valve 5-23

GENERAL DESCRIPTION

All 1967 models are equipped with a new split brake

system as a safety feature. If a wheel cylinder or brake

line should fail at either the front end or rear end of

the vehicle, the operator can still bring the vehicle to

a controlled stop. The system is designed with separate

hydraulic systems for the front and rear brake using

a dual master cylinder (fig. 1). The design of the master

cylinder is similar to that used on the 1966 Corvette

in that it has two entirely separate reservoirs and outlets

in a common body casting. The front reservoir and outlet

is connected to the front wheel brakes, and the rear

reservoir and outlet is connected to the rear wheel

brakes. Two pistons within the master cylinder receive

mechanical pressure from the brake pedal push rod and

transmit it through the brake lines as hydraulic pressure

to the wheel cylinders. The filler cap is accessible from

inside the engine compartment.

A new brake pipe distribution and switch assembly

is mounted below the main cylinder. The front and rear

hydraulic brake lines are routed from the main cylinder,

through the brake pipe distribution and switch assembly,

to the front and rear brakes as shown in Figure 2. The

switch is wired electrically to the brake alarm indicator

light on the instrument panel. In the event of fluid loss

in either the front or rear brake system the indicator

on the instrument panel will illuminate red. (The indi-
cator will also' be illuminated when the parking brake is

applied.)

On Camaro models equipped with air conditioning, the

rear brake hydraulic line is routed through a pressure

regulator valve mounted on the left frame side rail

(fig. 3). The valve controls the hydraulic pressure to

the rear brakes resulting in the correct pressure balance

between the front and rear hydraulic systems.

The self-adjusting brakes (fig. 4), used on both front

and rear of all models, are the Duo-Servo single anchor

type which utilize the momentum of the vehicle to assist

in the brake application. The self-energizing or
self-

actuating force is applied to both brake shoes at each

wheel in both forward and reverse motion. The brake

shoe linings are bonded to the shoes.

Wheel cylinders are the double piston type permitting

even distribution of pressure to each brake shoe. To

keep out dust and moisture, both ejads of each wheel

cylinder are sealed with a rubber booC The wheel

cylinders have no adjustments.

The Chevrolet, Chevelle, and Camaro parking brakes

have a foot operated ratchet type pedal mounted to the

left of the steering column. A cable assembly connects

the pedal to an intermediate cable by means of an equal-

izer, where the adjustment for the parking brake is

incorporated. The intermediate cable attaches to the

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES
5-3

PRIMARY

SHOE

PAWL
WIRE LINK

OVERRIDE

LEVER

VERRIDE

SPRING

RETURN

SPRING

STAR
WHEEL

Fig.
3—Camaro
Pressure
Regulator
Valve
Fig.
4-Self-Adjusting
Brake

MAINTENANCE AND ADJUSTMENTS

In any service operation it is extremely important

that absolute cleanliness be observed. Any foreign matter

in the hydraulic system will tend to clog the lines, ruin

the rubber cups of the main and wheel cylinders and

cause inefficient operation or even failure of the braking

system. Dirt or grease on a brake lining may cause

that brake to grab first on brake application and fade

out on heavy brake application.

The split system consists basically of two separate

brake systems. When a failure is encountered on either,

the other is adequate to stop the vehicle. If one system

is not functioning, it is normal for the brake pedal lash

and pedal effort to substantially increase. This occurs

because of the design of the master cylinder which

incorporates ah actuating piston for each system. When

the rear system loses fluid and takes in air, its piston

will bottom against the front piston. When the front

system loses fluid and takes in air, its piston will

bottom on the end of the main cylinders body. The loss

of fluid in one of the systems causes an uneven hydraulic

pressure balance between the front and rear systems.

The brake pipe distribution and switch assembly, near

the main cylinder, detects the loss of pressure and il-

luminates the brake alarm indicator light on the instru-

ment panel. The pressure loss is felt at the brake pedal

by an apparent lack of brakes for most of the brake

travel and then, when failed chamber is bottomed, the

pedal will harden.

HYDRAULIC BRAKE FLUID

Use GM Hydraulic Brake Fluid, Supreme No. 11 or

equivalent when servicing brakes. This brake fluid is

satisfactory for any climate and has all the qualities

necessary for proper operation, such as a high boiling

point to prevent vapor lock and the ability to remain

fluid at low temperatures.
In the event that improper fluid has entered the system,

it will be necessary to service the system as follows:

1.
Drain the entire system.

2.
Thoroughly flush the system with clean alcohol,

188
proof,
or a hydraulic system cleaning fluid

such as "Declene".

3.
Replace all rubber parts of the system, including

brake hoses.

4.
Refill the system.

5. Bleed the system.

BLEEDING HYDRAULIC SYSTEM

The hydraulic brake system must be bled whenever

any line has been disconnected or air has in some way

entered the system. A ''spongy" pedal feeling when the

brakes are applied may indicate presence of air in the

system. The system must be absolutely free of air at

all times. Bleeding should be done on the longest line

first; the proper sequence to follow is left rear, right

rear, right front, and left front (fig. 5). Bleeding of

brake system may be performed by one of two methods—

either pressure or manual.

PRESSURE
BLEEDING

1.
Clean all dirt from top of main cylinder and remove

cylinder cover and rubber diaphragm.

2.
Reduce fluid level in main cylinder until reservoirs

are approximately half full.

NOTE:
Make sure brake fluid in bleeder equip-

ment is at operating level and that the. equipment

is capable of exerting 30 to 50 lbs. hydraulic

pressure on the brake system.

3.
Install brake bleeder adapter J-22489 (fig. 6) on

main cylinder. Connect hose from bleeder equipment

to bleeder adapter and open release valve on bleeder

equipment.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-7

LATCH PLATE

DIE BLOCK

TUBE
UPSET FLARE PUNCH

RAM GUIDE

STOP PLATE

Fig.
13—Flaring Operation--Position ing Tubing

2.
Remove the tubing from the die block and deburr

the inside and outside edges.

3.
Install compression couplings on tubing and dip end

of tubing to be flared in hydraulic fluid. This lubri-

cation results in better formation of the flare.

4.
Place on-half of the die blocks in the tool body with

the counterbored ends toward the ram guide. Now

lay the tubing in the block with approximately 1/2"

protruding beyond the end.

Fit the other half of the block into the tool body,

close the latch plate and tighten the nuts "finger

tight".

5. Select the correct size upset flare punch. One end

of this punch is counterbored or hollowed out to

gauge the amount of tubing necessary to form a

double lap flare. Slip the punch into the tool body

with the gauge end toward the die blocks. Install the

ram; then tap lightly until the punch meets the die

, blocks and they are forced securely against the

stop plate (fig. 13).

6. Using the supplied wrench, draw the latch plate

nut down tight to prevent the tube from slipping.

Tightening the nuts alternately (beginning with the

nut at the closed hole in the plate) will prevent

distortion of the plate. Remove the punch and the

ram. Now reverse the punch and put it back into the

tool body. Install the ram and tap it lightly until

the face of the upset flare punch contacts the face

of the die blocks (fig. 14). This completes the

first operation. Remove the ram and the punch.

7. To complete the flare, insert the pointed finish

flare punch and the ram into the tool body. Tap

the ram until a good seat is formed (fig. 15).

NOTE:
The seat should be inspected at inter-

vals during the finishing operation to avoid

over-seating.

LATCH

DIE BLOCK

TUBE
UPSET FLARE PUNCH
RAM GUIDE

RAM
1ST OPERATION

UPSET FLARE

PUNCH
2ND OPERATION

FINISH FLARE

PUNCH

Fig.
15—Flaring Operation—First and Second Flare

BRAKE ADJUSTMENT

Service Brake

Although the brakes are self-adjusting, a preliminary

or initial adjustment may be necessary after the brakes

have been relined or replaced, or whenever the length

of the adjusting screw has been changed. The final

adjustment is made by using the self-adjusting feature.

1.
With brake drum off, disengage the actuator from

the star wheel and rotate the star wheel by spinning

or turning with a small screw driver.

2.
Recommended

a. Use special Tool J-21177; Drum-to-Brake Shoe

Clearance Gauge, to check the diameter of the

brake drum inner surface (fig. 16).

Fig.
14—Flaring Operation—First Flare
Fig.
16—Using Drum-to-Brake Shoe Clearance

Gauge Tool J-21177

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-8

Fig.
17—-Checking Brake Shoe Lining Clearance

Using Tool J-21177

b.
Turn the tool to the opposite side and fit over

the brake shoes by turning the star wheel, until

the gauge just slides over the linings (fig. 17).

c. Rotate the gauge around the brake shoe lining

surface to assure prpper clearance.

Alternate

a. Using the brake drum as an adjustment fixture

turn the star wheel until the drum slides over

the brake shoes with a slight drag.

b.
Turn the star wheel 1-1/4 turns to retract the

shoes.
This will allow sufficient lining-to-drum

clearance so final adjustment may be made as

described in Step 4.

3.
Install the drum and wheel.

NOTE: 1: If lanced area in brake drum is

knocked out, be sure all metal has been re-

moved from brake compartment. Install new

hole cover in drum to prevent contamination

of the brakes.

NOTE: 2: Make certain when installing drums

that drums are installed in the same position

as when removed with the drum locating tang

in line with the locating hole in the wheel hub

(fig. 18).

4.
Make final adjustment by making numerous forward

and reverse stops, applying brakes with a firm

pedal effort until a satisfactory brake pedal height

results.

NOTE: Frequent usage of an automatic trans-

mission forward range to halt reverse vehic;..$

motion may prevent the automatic adjuster.:?

from functioning, thereby inducing low pedal

heights.
Fig.
.18—Aligning Drum Tang with Wheel Hub

Parking Broke

The rear brake assemblies serve a dual purpose in

that they are utilized both as a hydraulically operated

service brake and also as a mechanically operated

parking brake. In view of this dual purpose, the service

brake must be properly adjusted as a base for parking

brake adjustment; conversely the parking brake must

be properly adjusted for the service brake to function

as intended.

Adjustment

1.
Jack up both rear wheels.

2.
Apply parking brake, two notches from fully re-

leased position.

3.
Loosen the equalizer forward check nut, and tighten

or loosen the rear nut until a light to moderate drag

is felt when rear wheels are rotated.

4.
Tighten check nuts securely.

5.
Fully release parking brake and rotate rear wheels;

no drag should be present.

Inspection

If complete release of the parking brake is not ob-

tained, unless it is forcibly returned to its released

position, or if application effort is high, check parking

brake assembly for free operation. If operation is sticky

or a bind is experienced, correct as follows:

1.
Clean and lubricate brake cables and equalizer.

2.
Inspect brake assembly for straightness and align-

ment (replace if necessary).

3.
Clean and lubricate parking brake assembly.

4.
Check routing of cables for kinks or binding.

CHEVROLET CHASSIS SERVICE MANUAL

BRAKES 5-9

COMPONENT REPLACEMENT AND REPAIRS

PARKING BRAKE-CHEVROLET, CHEVELLE AND

CAMARO (Figs. 19 and 20)

Pedal Assembly

Removal

NOTE:
Remove positive cable from battery to

eliminate the possibility of creating short cir-

cuits under dash.

1.
Place parking brake pedal in released position.

2.
Remove equalizer check nut, and separate cable

stud from equalizer.

3.
Remove two attaching nuts from mounting studs

located in engine compartment.

4.
Remove front cable .ball end from pedal assembly

swivel.

5. Remove pedal assembly to dash brace attaching

screw.

6. Remove pedal assembly by lowering rear slightly

to avoid scratching dash, and pulling, it out of the

firewall.

Installation

1.
Place pedal assembly in position with the two mount-

ing studs protruding through the holes provided in

the firewall.

2.
Install and tighten pedal assembly to dash brace

attaching screw.

3.
Position front cable ball end into pedal assembly

swivel.

4.
Install and tighten two attaching nuts on mounting

studs located in engine compartment.

5. Place
,
equalizer in position on center cable and

insert front cable stud through equalizer and secure

with check nut.

6. Adjust parking brake as outlined under Maintenance

and Adjustments in this section.

7. Connect positive battery cable.

Front Cable

Removal

NOTE:
Remove positive cable from battery to

eliminate the possibility of creating short cir-

cuits under dash.

1.
Place parking brake pedal in released position.

2.
Remove equalizer check nut, and separate cable

, stud from equalizer.

3.
Remove retainer from cable assembly at inner side

of frame rail.

4.
Remove ball end of cable from pedal assembly

swivel.

5. Compress expanded conduit locking fingers at toe

pan arid withdraw cable from car.

6. On Chevelle, if necessary, remove rubber tube

from front cable.

Installation

1.
On Chevelle, if necessary, replace rubber tube

over front cable.

2.
Position cable ball and conduit tip through cutout

in firewall. Make sure conduit locking fingers are

fully expanded and secured in cutout, then position

cable ball into pedal assembly swivel.
3.
Feed stud end of cable through frame rail and se-

cure with retainer on inner side of frame.

4.
Place one check nut on cable stud and insert stud

through equalizer, (make sure center cable is in

position), then place second check nut on stud.

5. Adjust parking brake as outlined in this section.

6. Connect positive battery cable.

Center Cable

Removal

1.
Place parking brake pedal in released position.

2.
Remove equalizer check nut and remove equalizer

from cable.

3.
Remove cable from cable guides.

4.
Disconnect center cable from rear cables at

connectors.

Installation

1.
Install cable ends into rear cable connectors.

2.
Place cable through equalizer and install equalizer

on to front cable stud, secure with check nut. (Do

not tighten.)

3.
Install cable in cable guides (figs. 19 and 20),

4.
Adjust parking brake as outlined in this section.

Rear Cables

Removal

1.
Place parking brake pedal in released position.

2.
Remove equalizer check nut and remove equalizer

from cable.

3.
Remove rear cable from connector.

4.
Remove retainer from rear cable at frame bracket.

Pull cable out of bracket.

5. Remove rear brake drum as outlined in this section.

6. Remove rear brake shoes as outlined in this section.

7. Remove cable end from parking brake actuating

lever.

8. Compress expanded conduit locking fingers at flange

plate entry hole and withdraw cable.

Installation

1.
Pass end of cable and conduit tip through flange

plate entry hole, making sure that conduit locking

fingers all expand fully.

2.
Connect cable end to actuating lever.

3.
Install rear brake shoes, drum and wheel as out-

lined in this section.

4.
Pass cable through frame bracket and install

retainer.

5. Install cable end into cable connector.

6. Position equalizer on center cable and place on

front cable stud, secure with check nut.

7. Make sure all center cable guides are in place

and adjust parking brake as outlined in this section.

PARKING BRAKE-CHEVY II (Fig. 21)

Lever Assembly

Removal

NOTE:
Remove positive cable from battery

to eliminate possibility of creating short cir-

cuits under dash.

CHEVROLET CHASSIS SERVICE MANUAL