1953 JEEP DJ engine

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

J
THREE-SPEED
TRANSMISSION

Contents

SUBJECT
PAR.

GENERAL
J-l
TRANSMISSION
SHIFTING
CONTROL.
. J-2
TRANSMISSION
REMOTE
CONTROL
ADJUSTMENT
J-3

REMOTE
CONTROL
DISASSEMBLY
J-4

REMOTE
CONTROL
REASSEMBLY.
. . . . J-5
TRANSMISSION
REMOVAL
J-6

SEPARATING
TRANSMISSION
AND
TRANSFER
CASE
J-7
SUBJECT
PAR.

DISASSEMBLY
OF
CANE
SHIFT
TRANSMISSION
J-8, J-12, J-16
Transmission
Cleaning and
Inspection J-10, J-18

Transmission
Interlocking Sleeve Inspection J-9

REASSEMBLY
OF
CANE
SHIFT
TRANSMISSION
J-ll,
J-14, J-19

SERVICE
DIAGNOSIS
J-20

TRANSMISSION
SPECIFICATIONS
J-21
J-1.
GENERAL
A
three speed synchromesh transmission is standard
equipment on all 'Jeep' Universal vehicles.
The
models T90 and T96 transmissions are used

with
the
Hurricane
F4 engine, and models
T86AA
and
T14A transmissions are used with the Daunt­
less
V-6 engine. All model transmissions are similar

in
design with exception of the T14A which is a

fully
synchronized (all forward gears) transmission

with
helical drive gears throughout.
The
transmission assembly is attached to the
rear

face of the flywheel bell housing and is supported on a rubber insulator at the frame center cross member which forms the
rear
engine
support.

All
4-wheel-drive vehicles are equipped with a
transfer
case attached to the
rear
of the trans­mission.
Transfer
case service and repair procedures

are
described in Section
K.

Models
CJ-5A,
and
CJ-6A
are equipped with the
same transmission, but with a remote control shift.
Models DJ-5 and DJ-6 are equipped with a similar

transmission,
however, the construction is
some­
what different because it is not designed to receive a transfer case for four-wheel drive.

For
DJ-5 and DJ-6 2WD vehicles, the trans­ mission repair procedures begin with Par. J-12.
J-2.
TRANSMISSION SHIFTING CONTROL
The
shift of the three-speed transmission is smooth

and
positive. The cane control lever shifts the trans­
mission gears direct from the shift control housing
mounted to the top side of the transmission housing.

The
remote control lever shifts the transmission
gears through remote control rods attached to the

adjusting
levers of the shift shafts protruding from the left side of the transmission housing. Poppet
balls and springs retain the transmission gears in mesh and an interlocking mechanism prevents
shifting into two gears at the same time.
J-3.
Transmission Remote Control Adjustment
•
Early
CJ-5A,
CJ-6A

First
disconnect the transmission shift rods from the remote control levers.
Check
for binding of
the remote control shaft on the steering column

and
make the necessary corrections to eliminate any binding condition.

If
the shift is not smooth and positive, first make

sure
the gears are in neutral position then remove
the shift rods at the transmission by removing
clevis pins, Fig. J-l No. 17, and slip a short piece
of snug fitting 34" [6,35 mm.] aligning rod, through
the gearshift levers and housing as shown in insert
drawing.

This
places the clutch and shift lever assemblies

in
the neutral position. Adjust the shift rod yokes
at the transmission end, so clevis pins can be in­ stalled freely without moving the shift levers on the
transmission after which remove alignment pin.
If
shifting from first to second is difficult or trans­
mission hangs in first gear, shorten the low and
reverse shift rod one
turn
at a time until the con­
dition is corrected. Usually three turns are re­

quired.

Should
the fault continue after completing the above adjustment, check further as outlined below.

First
remove the lubricating fitting. Use a narrow
feeler
gauge
which
will
enter the opening for the
lubricator
and check the clearance
between
the
faces of the shifting clutches.
This
clearance should
be .015" to .031", [W to W]
[0,397-0,794
mm.]. If
this clearance is greater the assembly must be removed for adjustment. The shift dog, which

engages
the clutch slots, should not have more than .009" [0,229 mm.] clearance in the slots. If the clear­
ance
between
the clutch
grooves
and cross pins is
too great,
these
parts must be replaced.
J-4.
Removal
of
Remote Control
m
Early
CJ-5A,
CJ-6A

•
Refer to Fig. J-l

To
remove the remote control the following pro­ cedure is
suggested:

a.
Remove shifting rods from the transmission

and
also from the steering remote control clutch levers. 239

THREE-SPEED
TRANSMISSION

FIG.
J-l—TRANSMISSION

REMOTE
CONTROL
CJ-5
A,
CJ-6A

1— Stop Screw
2—
Bias
Spring

3—
Gearshift
Lever
4—
Lever
Ball

5—
Steering
Wheel 6—
Horn
Button 7—
Column
and Bearing
8—
End
Huts
9—
Shift
Rod
Ends

10—
Shift
Rod
11—
Shift
Rod
12—
Cross-Shift
Bracket

13—
Control
Shaft
14—
Lubrication
Fitting
15—
Lever
and
Clutch

16—
Adjusting
Yoke

17—
Aligning
Rod 11706

b.
Remove gearshift lever fulcrum pin and the
gearshift lever.

c.
Remove plates on the toe board at the steer­
ing
post.

d.
Remove two screws holding remote control
housing to the steering
post
and lift the housing
from
the positioning pin.

e.
Remove the assembly down through the floor
pan.

f. Remove the lower clutch and shift lever from the housing by turning counterclockwise.
g. Remove upper clutch and shift lever in the same

manner.

h. Wash all parts in a suitable cleaning solution.

J-5.
Reassembly of
Remote
Control
•
Refer to
Fig.
J-l

Check
clearance of shift dog which
engages
in slot
of clutches, and if found to be greater than .009" [0,229 mm.] clearance, replace the worn parts.
Assemble upper clutch lever assembly in housing
making
sure that the alignment
hole
in the housing
faces toward the engine.
Turn
the upper lever as­
sembly in as far as it
will
go and then back off one

full
turn
until the
hole
in the clutch lever aligns

with
hole
in the housing.
Assemble the lower clutch lever assembly in hous­ ing until faces of clutches contact then back off
not more than one-half
turn
which should bring
the aligning
hole
in the lever in line with the
hole
in
the housing. If the one-half
turn
does
not bring
the alignment
hole
in proper position, it
will
be
necessary to grind off (square with axis not to exceed .015") [0,397 mm.] the face of the lower

clutch;
in other words, backing off not more than
one-half
turn
from face to face contact
gives
the

proper
clearance of .015" to .031"
[0,397-0,794
mm.]

between
the two clutches.
Assemble the unit to the steering
post
in reverse

order
of dismantling and adjust remote control

rods.
After
assembly, if the shift dog catches on the
edge

of the slot in the clutch when moving the lever up

and
down, disconnect the shift rod at the
transmission
end and either lengthen or shorten it
slightly to correct this condition.

J-6.
TRANSMISSION
REMOVAL
The
following repair procedures given in Par. J-7
through J-ll for the standard
3-speed
transmission
apply
in general to all models listed. Minor dif­
ferences
between
models that affect the procedure

are
noted. Procedure for the optional
4-speed
trans­mission
begins
with Section
J-l.

Removal
is as follows:

a.
Drain
the transmission and transfer case. Re­ place the
drain
plugs.

b.
Remove the floor pan inspection plate.

c.
Remove the shift lever and shift housing as­ sembly and its gasket from the transmission. On 240

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

J

10489

FIG.
J-2—THREE-SPEED
TRANSMISSION
— T90 1—
Main
Drive
Gear

2—
Main
Drive
Gear
Bearing
Retainer

3—
Main
Drive
Gear
Bearing
Retainer Oil
Seal
4—
Main
Drive
Gear
Snap
Ring

5—
Main
Drive
Gear
Bearing
Snap
Ring

6—
Main
Drive
Gear
Bearing
7—
Synchronizer
Shifting Plate
8—
Shift
Rail
Cap
9—
Shift
Rail—High
and Intermediate
10—
Shift
Rail
Poppet
Ball

11—
Shift
Rail
Poppet
Spring

12—
Shift
Fork—High
and Intermediate

13—
Control
Housing
14—
Control
Lever
Support
Spring

15—
Control
Lever
Housing Pin
16—
Control
Lever
Fulcrum
Ball

17—
Gear
Shift
Lever
18—
Shift
Fork—Low
and Reverse

19—
Sliding
Gear—Low
and Reverse
20—
Main
Shaft
Bearing
Adapter

21—
Main
Shaft
Bearing
22—
Main
Shaft
Washer

23—
Main
Shaft Nut
24—
Main
Shaft

25—
Idler
and Countershaft
Lock
Plate
26—
^Countershaft
Gear
Bearing
Rollers

2
7—Countershaft

28—
Countershaft
Thrust
Washer
Rear—Steel

29—
Countershaft
Thrust
Washer
Rear—Bronze

30—
Countershaft
Gears
31—
Transmission
Case

32—
Main
Shaft Second Speed
Gear
33—
Countershaft
Bearing
Spacer
34—
Synchronizer
Blocking
Ring

35—
Countershaft
Thrust
Washer
Front—Bronze

36—
Countershaft
Bearing
Washer

37—
Intermediate
and High Speed
Clutch
Sleeve

38—
Intermediate
and High
Clutch
Hub

39—
Synchronizer
Spring

40—
Intermediate
and High
Clutch
Hub
Snap
Ring

41—
Main
Shaft Pilot
Bearing
Roller

CJ-5A,
CJ-6A
models, remove the remote control

rods.

d.
Remove the set screw from the transfer case
shift lever pivot pin. Remove the pivot pin, shift

levers,
and shift lever springs. On models
CJ-5A,
and
CJ-6A
remove pivot pin cotter key and the

adjusting
rod attaching nut to remove shift lever.
See
Fig.
J-l.

e. If the vehicle is equipped with power take-off,
remove the shift lever plate screws and lift out the

lever.

f. Disconnect the front and
rear
propeller shafts
from
the transfer case, following the procedure de­

tailed
in Section
L.
Should the vehicle be equipped

with
power take-off, disconnect the transfer case end of the power take-off drive shaft.
g. Disconnect the
speedometer
cable at the transfer case.

h.
Disconnect the hand brake cable.
i.
Disconnect the clutch release cable at beilcrank
yoke end.
j.
Place
jacks
under the transmission and engine,
protecting the
engine
oil pan with a block of wood,
k.
Remove the nuts holding
rear
mounting to

frame
cross member.

I.
Remove the transfer case snubbing rubber bolt
nut at cross member.

m.
Remove
bolts
holding frame center cross mem­

ber
to frame side
rail
and remove cross member,
n.
Remove
bolts
holding transmission to flywheel
bellhousing.
o.
Force
transmission to right to
disengage
clutch
control
lever tube
ball
joint.

p.
Lower
jacks
under
engine
and transmission.

Slide
transmission and transfer case assemblies

toward
rear
of vehicle until the clutch shaft clears the flywheel housing.
q.
Lower
jack
under transmission. Remove trans­ mission and transfer case as an assembly from

under
the vehicle.

r.
For separation of the transmission and transfer
case, refer to Par. J-7. 241

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

J J-20
TRANSMISSION
SERVICE
DIAGNOSIS

SYMPTOMS
PROBABLE
REMEDY

Lock
in Two
Gears
Replace
Poppet
or Shift Levers

Slips
Out of High Gear Transmission Misaligned with Bellhousing

End
Play in Main Drive Gear Damaged Pilot Bearing or Front Bearing.

Slips
Out of Second
Worn
Gear Replace
Weak
Poppet
Spring Replace

Noise
in Low Gear
Gear
Teeth Worn Replace Gears
Shifting
Shoe
Bent Replace
Shoe
Lack
of Lubrication Drain and Refill

Grease
Leak into Bellhousing Gasket Broken Front Bearing Retainer Replace
Transmission Main Drive Gear Oil Seal Replace Align Transmission Case to Bellhousing
and Bellhousing to Engine
Tighten Front Retainer
Replace
J-21.
TRANSMISSION
SPECIFICATIONS

HURRICANE
F4
ENGINE
3-SPEED

Vehicle:
CJ-3B,
CJ-5,
CJ-5A,

CJ-6,
CJ-6A
DJ-5,
DJ-6
Make
Type

Speeds

Ratios: —
First
Second

Third

Fourth
Warner

T90C

Synchronous Mesh
3 Forward — 1 Reverse
3.339
to 1 1.551 to 1 1.000 to 1
Warner

T96

Synchronous Mesh
3 Forward — 1 Reverse
2.605
to 1 1.630 to 1
1.000 to 1
Reverse
Interlock
Poppet
Clearance. . .
3.798
to 1

3.536
to 1
.001" to .007"

[0,025
a 0,178 mmJ

DAUNTLESS
V-6
ENGINE
3-SPEED

Vehicle:
CJ-5,
CJ-6,
CJ-5A,
CJ-6A

DJ-5,
DJ-6
Late
CJ-5, CJ-6
Make
Warner
Warner Warner

Model
AS7
T86AA

AS9
T86AA
T14A

Type..
Synchromesh
Synchromesh Synchromesh

Speeds
3 Forward — 1 Reverse 3 Forward — 1 Reverse 3 Forward — 1 Reverse
Ratios: —
First
2.798
to 1
2.798
to 1
3.100 to 1

Second
1.687 to 1 1.687 to 1 1.612 to 1

Third
1.000 to 1
1.000 to 1 1.000 to 1
Reverse
3.798
to 1
3.798
to 1 3.100 to 1 257

Jl

FOUR-SPEED
TRANSMISSION
J1-1.
GENERAL

A
model T-98 four-speed transmission with a cane- type shift is optional on 'Jeep* Models CJ-5 and
CJ-6
equipped with the Hurricane F4
engine.
A model T-18 four-speed transmission is optional on
the 'Jeep* Model
CJ-5
equipped with the Dauntless
V6
engine.
These transmissions provide four
speeds

forward
and one reverse with synchromesh
engage­
ment in second,
third,
and fourth speed.

For
quick identification, the optional
4-speed
transmission is 11%"
[30,16
cm.] long whereas the

standard
3-speed
transmission is 8"
[20,32
cm.] long. However the instructions for removal and
installation of the two transmissions are the same.

J1-2.
Four-Speed
Transmission Removal Use the procedure outlined under the heading,
"TRANSMISSION
REMOVAL"
Section J Par.

J-6.
FIG.
Jl-2—FOUR-SPEED TRANSMISSION MAIN DRIVE
GEAR

1—
Snap
Ring
3—Bearing 5—Main
Drive
Gear

2—
Snap
Ring
4—Washer 6—Bearing Rollers

FIG.
Jl-3—T-98
FOUR-SPEED TRANSMISSION MAIN SHAFT 1—
Blocking
Ring

2—
Direct
and
Third
Clutch
Sleeve

3—
Snap
Ring

4—
Spring

5—
Shifting
Plate
6—
Direct
and
Third
Clutch
Hub 7—
Third
Speed
Gear
Assembly
8—
Snap
Ring
9—Thrust
Washer
10—
Bearing
Rollers

11—
Second Speed
Gear

12—
Spacer
13—
Mainshaft

14—
Blocking
Ring

15—
Shifting
Plate
16— Poppet
Spring
17—
Ball

18—
Low
and Second
Clutch
Hub 19—
Retaining
Ring

20—
Low
and Second Speed
Gear
21—
Second Speed
Synchronizer
Assembly
22—
Direct
and
Third
Synchroniser Assembly 260

Jl

FOUR-SPEED
TRANSMISSION
Jl-9.
TRANSMISSION
SER¥ICE
DIAGNOSIS

SYMPTOMS

Lock
In Two Gears

Slips
Out of High Gear Transmission Misaligned with Bellhousing

End
Play in Main Drive Gear Damaged Pilot Bearing or Front Bearing.
Slips Out of
Second
Worn
Gear
Weak
Poppet
Spring
PROBABLE
REMEDY

Replace
Poppet
or Shift Levers
Align Transmission Case to Bellhousing and Bellhousing to Engine
Tighten Front Retainer Replace
Replace Replace

Noise
in Low Gear
Gear
Teeth Worn. Replace Gears
Shifting
Shoe
Bent Replace
Shoe
Lack
of Lubrication Drain and Refill

Grease
Leak into Bellhousing Gasket Broken Front Bearing Retainer......... Replace Transmission Main Drive Gear Oil Seal Replace

Jl-10.
TRANSMISSION
SPECIFICATIONS

HURRICANE
F4
ENGINE
4-SPEED

Vehicle:
CJ-5,
CJ-6

Warner
T98A

Type..
• Synchronous Mesh
4 Forward — 1 Reverse
Ratios: —
First
. .
6.398
to 1

Second
3.092
to 1

Third
1.686 to 1

Fourth
1.000 to 1

7.820
to 1

DAUNTLESS
V-6
ENGINE
4-SPEED

Vehicle:
Late
CJ-5 Only

Warner

Model T-18
Type Synchromesh
4 Forward — 1 Reverse
Ratios: —
First
4.02 to 1

Second
2.41 to 1

Third
1.41 to 1

Fourth
1.00 to 1
Reverse 4.73 to 1 266

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

ft
TRANSFER CASE

Contents

SUBJECT
PAR.

GENERAL
. . .K-1

TRANSFER CASE REMOVAL
K-2
TRANSFER CASE DISASSEMBLY
K-3
Front
Bearing Cap K-4

Rear
Bearing Cap K-5

TRANSFER CASE REASSEMBLY.
. .K-6

TRANSFER CASE INSTALLATION
K-7
TRANSFER CASE LINKAGE
ADJUSTMENT
K-8

SERVICE
DIAGNOSIS
K-9

SPECIFICATIONS
.K-10

K-1. GENERAL
All
4-wheel-drive models are equipped with a
transfer
case to connect the power to the front
axle.
It is essentially a
two-speed
transmission
located at the
rear
of the standard transmission
and
provides a low and direct gear.

The
transfer case gears are controlled by the
driver

through
one shift lever.
Early
'Jeep'
Universal
Models with the F4-134
Hurricane
engine
are equipped with two transfer case shift control levers.

a.
On vehicles equipped with one transfer case

shift
lever, the transfer case shift lever has four
positions: 2WD
High,
4WD
High,
Neutral, and
4WD
low. The forward position of the lever 2WD

High
allows the
rear
wheels only to drive. The

first
rear
position (4WD High)
engages
the 4- wheel drive and provides high range 4-wheel drive.

The
second
rear
position (Neutral)
disengages
all power to the wheels and is used for stationary
power take-off operations. The last
rear
position
(4WD
Low) provides low range 4-wheel drive.

b.
On vehicles equipped with two transfer case

shift
levers, the transfer case front axle drive lever (left hand lever)
gives
a choice of 2-wheel or 4-
wheel drive. In the forward (out) position the
vehicle is in 2-wheel drive. Move the lever to the

rear
(in) position for 4-wheel drive operation.
The
4-wheel-drive
auxiliary-range
shift lever (right

hand
lever) has three positions; low, neutral, and
high.
The forward position (low)
gives
low-range
4-wheel drive. The center position (neutral) dis­
engages
all power to the wheels and is used for

stationary
power take-off operations. A built-in in­

terlock
prevents shifting into low range, 2-wheel
drive.
This
feature protects the
rear
axle from over­

load.
K-2.
Removal of
Transfer
Case

The
transfer case may be removed from the vehicle
without removing the transmission. Where both

transmission
and transfer case are to be removed
together,
refer to Section J. To remove only the

transfer
case from the vehicle, proceed as follows:

a.
Drain
transmission
and transfer case and replace

drain
plugs.

b.
Disconnect the brake cable.

c.
Disconnect front and
rear
propeller shafts at
the transfer case. See "Propeller Shafts and
Uni­
versal
Joints."

d.
Disconnect
speedometer
cable at transfer case. e. Disconnect the transfer case shift levers. On
vehicles equipped with two shift levers
loosen

set screw and remove pivot pin. Use a screw
driver

to pry shift lever springs away from shift levers.
Lift
levers from transfer case. On models equipped

with
a single shift lever remove pivot pin cotter

key,
and the adjusting rod attaching nut to remove

shift
lever. See Fig. K-4.
f. Remove cover plate on
rear
face of transfer case.

Remove
cotter key, nut and washer from trans­

mission
main shaft.
g. If possible, at this point remove the transfer case main drive gear from the transmission main

shaft.
If not possible, see
step
j below.

h.
Remove transfer case torque reaction support

bracket
bolt and nut.

i.
Remove transmission to transfer case bolts.
j.
Remove transfer case. If the transfer case main

drive
gear has not been removed in
step
g above,
proceed as follows:
Brace
the end of the trans­

mission
main shaft so that it cannot
move
in the
transmission,
pull
the transfer case to the
rear
to 267

L

PROPELLER
SHAFTS
AND
UNIVERSAL JOINTS

move
the snap rings, pinch the ends
together
with

a
pair
of pliers. If the rings do not readily snap
out of the groove, tap the end of the bearing lightly
which
will
relieve pressure against the rings.
After
removing the snap rings, press on the end of
one bearing until the
opposite
bearing is pushed
from
the yoke arm.
Turn
the joint over and press
the first bearing back out of that arm by pressing
on the
exposed
end of the
journal
shaft. Use a
soft
ground drift with a flat face about [0,8 mm.]

smaller
in diameter than the
hole
in the yoke arm
and
drive it out, otherwise there is danger of damag­ing the bearing.

Repeat
this operation for the other two bearings,
then lift out
journal
assembly by sliding it to one
side.

L-4.
Snap
Ring
Type Assembly

Wash
all parts in cleaning solvent and inspect the
parte
after cleaning. Replace any parts that indicate
extensive
wear.
It is advisable to install new gaskets
on the
journal
assembly regardless of the condition of the old gaskets. Make certain that the grease

channel
in each
journal
trunnion is open.

Pack
the bearing
cones
one-third
full
of lubricant
and
install the rollers.
Draw
the bearings into the end yoke arm and seat
them firmly against the bearing shoulders. Hold
the bearings in a vertical position to prevent the
needles
from dropping out until the joint is as­ sembled. If the joint binds when assembled, tap
the arms lightly to relieve any pressure on the bear­
ings at the end of the
journal.

L-5.
U-Bolt
Type Disassembly

Removal
of the attaching "U"-bolt releases one set
of bearing races. Slide the propeller shaft into the
yoke flange to remove them using care not to
lose
the rollers.
After
the removal of the one set of bearing races,
release the other set by removing the snap rings

in
the
sleeve
yoke by pinching the ends
together

with
a
pair
of pliers. Should the rings
fail
to snap
readily
from the groove, tap the end of the bearing
lightly,
which
will
relieve the pressure against them.

Press
on the end of one bearing, until the
opposite
bearing
is pushed out of the yoke arm.
Turn
the

universal
joint over and press the first bearing out
by pressing on the
exposed
end of the
journal
as­
sembly. Use a
soft
ground drift with a flat face about
\{i
[0,8 mm.] smaller in diameter than the
hole
in the yoke
arm
and drive out the bearing.
Lift

the
journal
out by sliding to one side.
Clean
all
parts
and check for wear.

L-6.
U-Bolt Type Assembly

Wash
all parts in cleaning solvent and inspect the
parts
after cleaning. Replace any parts that indicate
extensive
wear.
It is advisable to install new gaskets
on the
journal
assembly regardless of the condition
of the old gaskets. Make certain that the grease
channel
in each
journal
trunnion is open.

Pack
the bearing
cones
one-third
full
of lubricant
and
install the rollers.
Draw
the bearings into the end yoke arm and seat
them firmly against the bearing shoulders. Hold the
bearings in a vertical position to prevent the
needles
from dropping out until the joint is as­
sembled. If the joint binds when assembled, tap the arms lightly to relieve any pressure on the
bearings at the end of the
journal.
Tighten the
U-bolts equally. U-bolt torque wrench reading is 15 to 20 lb-ft. [2,07 a 2,76 kg-m.].

When
installing the assembly in the vehicle be sure
that the arrows on the propeller shaft and yoke

sleeve
are in alignment as shown in Fig. L-2, or
that the unmarked joints are aligned with the yokes in the same parallel plane.

SPECIFICATIONS

L-7.
PROPELLER
SHAFTS
AND
UNIVERSAL JOINTS
PROPELLER
SHAFTS:

Make
SPICER

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
Front

Rear

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
O.D.

Length

O.D.
Length

Dimensions:

F4
Engine Vehicles:
CJ-5,
CJ-5
A
— 3 Speed.
......
4 Speed

CJ-6,
CJ-6A
— 3 Speed 4 Speed

CJ-3B
DJ-5
DJ-6.
V-6
Engine Vehicles:
CJ-5,
CJ-5A
— 3 Speed.

CJ-6,
CJ-6A
— 3 Speed.

CJ-5
— 4 Speed
1M"
[3,175 cm.]

1M*
[3,175 cm.]

\W
[3,175 cm.]
1M*
[3,175 cm.] [3,175 cm.]

\W
[3,175 cm.]

\W
[3,175 cm.] [3,175 cm.] 22^" [57,78 cm.]

28H"
[72,39 cm.]
22M*
[57,78 cm.]

mW
[72,39 cm.]

33He"
[85,57 cm.]

21W
[55,25 cm.]
21%"
[55,25 cm.]

2&* [68,10
cm.]
IK"
[4,45 cm.]

1M#
[4,45 cm.]

\%"
[4,45 cm.]

\%"
[4, 45cm.]

IW
[4,45 cm.]

1M*
[4,45 cm.]

3*
[7,62 cm.]
2" [5,08 cm.]
2" [5,08 cm.]
l%" [4,45 cm.]
182£"
[45,95 cm.]
WW
[34,131
cm.]

3SJ4*
[97,79 cm.]

33%"
[84,69 cm.] 19546*
[50,64
cm.]
24^"
[61,60
cm.]

44M*
[112,40
cm.]

19%?
[50,64
cm.] 39* [99,06 cm.]

U%"
[37,47 cm.l

UNIVERSAL
JOINTS:
Make
Spicer

Cardan
Cross
Antifriction

Type
Spicer

Cardan
Cross
Antifriction

Bearing
Spicer

Cardan
Cross
Antifriction

276