2023 RAM 1500 Owners Manual

GETTING TO KNOW YOUR VEHICLE87

Position Two (Front And Rear Latches Latched)

TRI-FOLD TONNEAU COVER FOLDING
F
OR DRIVING OR REMOVAL
To remove the Tonneau Cover use the following steps:

1. Open the tailgate to access the rear pair of Tonneau
Cover latches located on the underside of the Cover.

Location Of Rear Latches
Slide Locking Lever Inward

2. Slide the locking lever toward the inside of the truck bed to release the J Hook and pull the handle
downward into the released position.

Unlatching Latch
Released Position

1 — Panel 1
2 — Panel 2
3 — Panel 3
2

23_DT_OM_EN_USC_t.book Page 87

88GETTING TO KNOW YOUR VEHICLE

Hold The Bumper And Push The Handle Up

3. Holding the bumper, push the fully released latch to
the center and push up. Push the handle firmly,
locking it into the stowed position. Repeat Steps 2
and 3 for the opposite side latch.

Stowed Position Lift Panel 3 And Fold Onto Panel 2

4. Lift up on Panel 3 and fold it onto Panel 2.

Correct Folding — Hold Panels Together
NOTE:
When folding the second and third panels, the sections
MUST
be held together to avoid damage to the cover
material. Fold the panel gently. Do not allow the panels to
drop under their own weight.

Incorrect Folding — Will Cause Damage

5. Lift up on the second and third panel and fold them onto the first panel.

Stowage Strap Clipped

23_DT_OM_EN_USC_t.book Page 88

GETTING TO KNOW YOUR VEHICLE89
6. Unsnap the stowage strap and clip. Repeat for both
straps to prevent the Tonneau Cover panels from
unfolding.

Position One
(Front Latches Latched And Stowage Straps Secured)

NOTE:
Be sure the Tonneau Cover has been folded completely,
and the stowage straps are engaged, before removing.

Fully Folded Tonneau Cover

NOTE:
The vehicle can be driven with the Tonneau Cover in the
folded position or can be completely removed.

Slide Locking Lever Inward

7. Slide the locking lever toward the inside of the truck bed to release the J Hook and pull the handle
downward into the released position.

Unlatching Latch
Released Position

CAUTION!
The folded Tonneau Cover must be latched by both
front latches and both front stowage straps or damage
to the Tonneau Cover or vehicle may occur while driving.
2

23_DT_OM_EN_USC_t.book Page 89

90GETTING TO KNOW YOUR VEHICLE

Hold The Bumper And Push The Handle Up

8. Holding the bumper, push the fully released latch to
the center and push up. Push the handle firmly,
locking it into the stowed position. Repeat Steps 2 &
3 for the opposite side latch.
9. With two people, remove the cover.
TRI-FOLD TONNEAU COVER
I
NSTALLATION
To install the Tonneau Cover follow these steps:

1. Position the Tonneau Cover on the truck bed and
center using the locating bumpers.

2. Locate the front pair of Tonneau Cover latches on the underside of the Cover. Slide the locking lever toward
the inside of the truck bed and release the latch from
the stowed position, and pull the handle downward
into the released position. Do this for both the left and
right side.

Location of Front Latches
Slide Locking Lever Towards Inside Of Truck Unlatching Latch
Released Position

3. Swing the J Hook from the handle and push the handle to the center and up, ensuring that the J Hook
is under the truck flange. Push up on the handle
firmly, locking it into the latched position.

23_DT_OM_EN_USC_t.book Page 90

GETTING TO KNOW YOUR VEHICLE91

J Hook Under Truck Flange

NOTE:
Make sure the bumper is in front of the truck flange bead.

Pull Handle Downward

4. Pull down on the handle to ensure the Slide Locking Lever is fully engaged. Do this for both the left and
right side.
5. Unclip the stowage straps, and re-snap them to the bow.
6. Unfold the Tonneau Cover to the second panel position.

Incorrect Folding — Will Cause Damage

NOTE:
When folding the second and third panels, the sections
MUST be held together to avoid damage to the cover
material. Fold the panel gently. Do not allow the panels to
drop under their own weight.

Second Panel Position

NOTE:
Unfold the panel gently, and do not allow the panels to
drop under their own weight.
7. Completely unfold the Tonneau Cover.
1 — Front Of Truck
2 — J Hook
CAUTION!
The vehicle cannot be driven when the Tonneau Cover
is in the second panel position.
2

23_DT_OM_EN_USC_t.book Page 91

92GETTING TO KNOW YOUR VEHICLE

Position Two (Fully Unfolded)

8. Repeat steps 2 through 3 for the rear pair of latches.
9. Pull down on the handle to ensure the Slide Locking
Lever is fully engaged. Do this for both the left and
right side.
NOTE:Also check to ensure the latch yellow bumpers are forward
of the bead on the underside of the truck flange. Make
sure that the Tonneau Cover is positioned fully forward, so
that the bumper clears the bead.

Pull Up On Tonneau Cover Corners

10. Gently pull up on all four corners of the Tonneau Cover to ensure that it is properly latched.
TRI-FOLD TONNEAU COVER CLEANING
For proper cleaning of the Tonneau Cover, use Mopar®
Whitewall & Vinyl Top Cleaner and Mopar® Leather & Vinyl
Conditioner/Protectant.
WARNING!
You must ensure the Tonneau Cover is properly
installed on the vehicle before driving. An unsecured
Tonneau Cover can fly off of the vehicle while in motion,
resulting in a collision, personal injury, and death.
Failure to follow this procedure can also damage the
vehicle and the Tonneau Cover.
CAUTION!
It is the driver’s responsibility to ensure the Tonneau
Cover is properly installed on the vehicle. Failure to
follow this procedure can result in detachment of the
Tonneau Cover from the vehicle and/or damage to the
vehicle/Tonneau Cover.

23_DT_OM_EN_USC_t.book Page 92

93
GETTING TO KNOW YOUR INSTRUMENT PANEL
MIDLINE INSTRUMENT CLUSTER — GASOLINE
Use this QR code to access your digital experience.
3

23_DT_OM_EN_USC_t.book Page 93

94GETTING TO KNOW YOUR INSTRUMENT PANEL
MIDLINE INSTRUMENT CLUSTER
D
ESCRIPTIONS — GASOLINE

1. Tachometer

Indicates the engine speed in revolutions per
minute (RPM x 1000).
2. Voltmeter When the vehicle is in the RUN state, the gauge
indicates the electrical system voltage. The
pointer should stay within the normal range if the
battery is charged. If the pointer moves to either
extreme left or right and remains there during
normal driving, the electrical system should be
serviced.
NOTE:In vehicles equipped with Stop/Start, a reduced voltage
may be present during an Autostop.
3. Instrument Cluster Display
When the appropriate conditions exist, this display
shows the instrument cluster display messages
Úpage 98.
 The display always shows one of the main menu
items after ignition on. 4. Oil Pressure Gauge
The pointer should always indicate the oil pres -
sure when the engine is running. A continuous
high or low reading under normal driving condi -
tions may indicate a lubrication system malfunc -
tion. Immediate service should be obtained from
an authorized dealer.
NOTE:In vehicles equipped with Stop/Start, an oil pressure indi -
cation of zero is normal during an Autostop.
5. Speedometer
Indicates vehicle speed.
6. Temperature Gauge The pointer shows engine coolant temperature.
The pointer positioned within the normal range
indicates that the engine cooling system is oper -
ating satisfactorily.
 The pointer will likely indicate a higher tempera -
ture when driving in hot weather, up mountain
grades, or when towing a trailer. It should not be
allowed to exceed the upper limits of the normal
operating range. 7. Fuel Gauge
The pointer shows the level of fuel in the fuel tank
when the ignition is in the ON/RUN position.
 The fuel pump symbol points to the
side of the vehicle where the fuel door
is located.
WARNING!
A hot engine cooling system is dangerous. You or others
could be badly burned by steam or boiling coolant.
You may want to call an authorized dealer for service if
your vehicle overheats
Úpage 350.
CAUTION!
Driving with a hot engine cooling system could damage
your vehicle. If the temperature gauge reads “H,” pull
over and stop the vehicle. Idle the vehicle with the air
conditioner turned off until the pointer drops back into
the normal range. If the pointer remains on the “H,”
turn the engine off immediately and call an authorized
dealer for service.

23_DT_OM_EN_USC_t.book Page 94