2022 YAMAHA YZF-R1 Owners Manual

Periodic maintenance and adjustment
7-8
7
EAU72811
TIPAir filter
• This model’s air filter uses a disposable oil-coated paper element. This element cannot be cleaned with compressed air, doing so will only damage it.
• The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
 Hydraulic brake service
• Regularly check the front and rear brake fluid levels. Replenish if necessary.
• Every two years replace the rear brake master cylinder, the internal components of the front brake master cylinder, the brake calipers, and change the brake fluid.
• Replace the brake hoses every four years or sooner if cracked, damaged, or if any section of the stainless steel brake hose has turned black.30 *Moving parts and
cables • Lubricate.
√√√√√
31 *Throttle grip • Check operation.
• Lubricate throttle grip housing
tube guides. √√√√√
32 *Lights, signals and
switches • Check operation.
• Adjust headlight beam.
√√√√√√
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)
UB3LE1E0.book Page 8 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-9
7
EAU88620
Cowlings and panelsThe cowlings and panels shown need
to be removed to perform some of the
maintenance jobs described in this
chapter. Refer to this section each time
a cowling or panel needs to be re-
moved and installed.Panels A and B
To remove a panel
Remove the quick fastener and bolt,
and then pull the panel off.
1. Panel A
2. Panel B
1
2
1. Cowling A
2. Panel C
1. Cowling B
2. Panel a
1
2
1
2 2
1. Quick fastener
2. Bolt
3. Panel A
1. Quick fastener
2. Bolt
3. Panel B
2
3 1 1
1
2
3
UB3LE1E0.book Page 9 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-10
7
To install the panel
Place the panel in its original position,
and then install the bolt and quick fas-
tener.
Panels C and D
To remove a panelRemove the bolts and washers, and
then pull the panel off.
To install the panel
1. Insert the projections into theholders as shown, and then place
the panel in its original position. 2. Install the washers and bolts.
Cowlings A and B (YZF-R1)
To remove a cowling
1. Remove the bottom panel.
2. Remove the quick fasteners.
1. Panel C
2. Bolt and washer
2 2
1
1. Panel a
2. Bolt and washer
1. Projection
2. Panel C
2 2 1
21 1
1. Projection
2. Panel a
2
1 1
UB3LE1E0.book Page 10 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-11
73. Pull the cowling forward to re-
move it.
To install a cowling
1. Place the cowling in its original po- sition, and then install the quick
fasteners. 2. Install the bottom panel.
Cowlings A and B (YZF-R1M)
To remove a cowling
1. Remove the bottom panel.
2. Remove the bolt and collar, and the quick fasteners.
3. Pull the cowling forward to re- move it. To install a cowling
1. Place the cowling in its original po-
sition, and then install the collar
and bolt, and the quick fasteners.
2. Install the bottom panel.
1. Panel
2. Quick fastener
3. Cowling
3
2
2
1
1. Panel
2. Bolt and collar
3. Quick fastener
4. Cowling
2
1
4
3
3
UB3LE1E0.book Page 11 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-12
7
EAU67110
Checking the spark plugsThe spark plugs are important engine
components, which should be
checked periodically, preferably by a
Yamaha dealer. Since heat and depos- its will cause any spark plug to slowly
erode, they should be removed and
checked in accordance with the peri-
odic maintenance and lubrication
chart. In addition, the condition of the
spark plugs can reveal the condition of
the engine.
The porcelain insulator around the
center electrode of each spark plug
should be a medium-to-light tan (the
ideal color when the vehicle is ridden
normally), and all spark plugs installed
in the engine should have the same
color. If any spark plug shows a dis-
tinctly different color, the engine could
be operating improperly. Do not at-
tempt to diagnose such problems
yourself. Instead, have a Yamaha deal-
er check the vehicle.
If a spark plug shows signs of elec-
trode erosion and excessive carbon or
other deposits, it should be replaced. Before installing a spark plug, the
spark plug gap should be measured
with a wire thickness gauge and, if
necessary, adjusted to specification.
Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the spark
plug threads.
NOTICE
ECA10841
Do not use any tools to remove or in-
stall the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in.
Specified spark plug:
NGK/LMAR9E-J
1. Spark plug gap
Spark plug gap:0.6–0.7 mm (0.024–0.028 in)
1
1
Tightening torque:Spark plug (new):
18 N·m (1.8 kgf·m, 13 lb·ft)
Spark plug (after checking):
13 N·m (1.3 kgf·m, 9.6 lb·ft)
UB3LE1E0.book Page 12 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-13
7
EAU36113
CanisterThis model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere. Before operating
this vehicle, make sure to check the
following: Check each hose connection.
 Check each hose and canister for
cracks or damage. Replace if
damaged.
 Make sure that the canister
breather is not blocked, and if
necessary, clean it.
EAU66536
Engine oil and oil filter car-
tridgeThe engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.
To check the engine oil level
1. Place the vehicle on a level surfa- ce and hold it in an upright posi-
tion. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for several minutes, and then turn it
off.
3. Wait a few minutes for the oil level to settle for an accurate reading,
and then check the oil level
through the check window locat-
ed at the bottom-left side of the
crankcase.TIPThe engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is at or below theminimum level mark, add suffi-
cient oil of the recommended type
to raise it to the correct level.TIPCheck the oil filler cap O-ring for dam-
age, and replace it if necessary.To change the engine oil1. Start the engine, warm it up for several minutes, and then turn it
off.
2. Place an oil pan under the engine to collect the used oil.
1. Canister
2. Canister breather
1
2
1. Engine oil level check window
2. Maximum level mark
3. Minimum level mark
2
3
1
UB3LE1E0.book Page 13 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-14
7
3. Remove the engine oil filler cap,
the engine oil drain bolt and its
gasket to drain the oil from the
crankcase. 4. Install the engine oil drain bolt and
its new gasket, and then tighten
the bolt to the specified torque.
5. Refill with the specified amount of the recommended engine oil.
TIPBe sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.NOTICE
ECA11621
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
 Make sure that no foreign mate-
rial enters the crankcase.
6. Check the oil filler cap O-ring for
damage, and replace it if neces-
sary.
7. Install and tighten the oil filler cap.
1. Engine oil filler cap
1. Engine oil drain bolt
2. Gasket
12
Tightening torque: Engine oil drain bolt:23 N·m (2.3 kgf·m, 17 lb·ft)
Recommended engine oil: Full synthetic
10W-40, 15W-50
Oil quantity: Oil change:3.90 L (4.12 US qt, 3.43 Imp.qt)
With oil filter removal: 4.10 L (4.33 US qt, 3.61 Imp.qt)
1. Engine oil filler cap
2. O-ring
12
UB3LE1E0.book Page 14 Tuesday, August 10, 2021 2:28 PM

Periodic maintenance and adjustment
7-15
78. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
TIPAfter the engine is started, the oil pres-
sure and coolant temperature warning
light should go off if the oil level is suf-
ficient.NOTICE
ECA22490
If the oil pressure and coolant tem-
perature warning light flickers or re-
mains on even if the oil level is
correct, immediately turn the engine
off and have a Yamaha dealer check
the vehicle.9. Turn the engine off, wait a few mi-nutes for the oil level to settle for
an accurate reading, and then
check the oil level and correct it if
necessary. To change the engine oil and replace
the oil filter cartridge
1. Remove cowling A and panel C. (See page 7-9.)
2. Follow steps 1–3 of the “To chan- ge the engine oil” section for the
oil draining procedure.
3. Remove the oil filter cartridge with an oil filter wrench.
TIPAn oil filter wrench is available at a
Yamaha dealer.4. Apply a thin coat of clean engine oil to the O-ring of the new oil filter
cartridge.
TIPMake sure that the O-ring is properly
seated.5. Install the new oil filter cartridgewith an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.
1. Oil filter cartridge
2. Oil filter wrench
1
2
1. O-ring
1
UB3LE1E0.book Page 15 Tuesday, August 10, 2021 2:28 PM