2022 TOYOTA GR86 remote control

115
3
3-2. Opening, closing and locking the doors and trunk
Before driving
cedure used to disable it again.
When enabled a buzzer will sound.
■Door opening/closing method
Make sure to firmly press the door lock
switch in steps 4 and 6. If the switch is
pressed for a very short time, the sys- tem may not be disabled.
■Wireless remote control method
To use the wireless remote control
method to disable the smart entry & start system, it is necessary to register a PIN
code for the PIN code smart entry.
( P.115)
■When enabling the smart entry & start system
If the method used to disable the smart
entry & start system is unknown, press the engine switch.
●If the wireless remo te control system was used, a buzzer inside the vehicle
will sound.
●If the door opening/closing method
was used, the buzzer will not sound.
■Customization
Some functions can be customized. ( P.377)
By registering a 5 digit PIN code, all
of the doors and the fuel filler door
can be unlocked without an elec-
tronic key by pressing the trunk
opener switch.
■PIN code registration method
1 Turn the engine switch off.
2 Close all of the doors and the
trunk.
3 Press and hold of the wire-
less remote control.
At this time, all of the doors and the fuel filler door will lock.
4 Within 5 seconds of performing
step 3, press and hold the trunk
opener switch.
After 5 seconds or more, a buzzer will sound.
5 Release of the wireless
remote control and the trunk
opener switch.
6 Within 30 seconds after the
buzzer begins sounding, press
of the wireless remote con-
trol.
The buzzer will stop.
7 A PIN code can now be regis-
tered. Press the trunk opener
switch the same number of
times as the first digit of the PIN
code.
For example: If registering 32468, press the switch 3 times.
NOTICE
■When disabling the smart entry &
start system
When disabling or enabling the sys- tem to accommodate persons with
implantable cardiac pacemakers, car-
diac resynchronization therapy pace- makers or implantable cardioverter
defibrillators, always use the door
opening/closing method. If the wire- less remote control method is used,
the system may be enabled acciden-
tally.
Unlocking the doors using
PIN code smart entry

1163-2. Opening, closing and locking the doors and trunk
8Wait for the buzzer to sound 1
time and then press the switch
the same number of times as for
the next digit.
For example: If registering 32468,
press the switch 2 times.
9 Repeat step 8 for the remaining
digits.
10 Within 30 seconds after the
buzzer begins sounding inter-
mittently, perform steps 7
through 9 again to confirm the
PIN code.
Registration is complete and all of the doors and the fuel filler door will unlock.
■Unlocking method
Press the trunk opener switch using
the same procedure as steps 7
through 9.
■PIN code registration
●To prevent theft, the same digit for all
5 digits and 12345 cannot be regis- tered as the PIN code. Also, avoid
using the same number as on your
license plate or other simple codes.
●To use 0 as a digit, press the trunk
opener switch 10 times.
●If a mistake is made during registra-
tion, unlock the doors or trunk using
the wireless remote control to cancel registration. Then perform registra-
tion again, starting from step 1. How-
ever, if the mistake was made in step 10 , a buzzer will sound and step 10
can be performed again.
●To clear the PIN code, perform the
registration procedure and enter
22222.
●After registering a new PIN code,
make sure to check that the doors can be unlocked using the code.
●If the smart entry & start system has
been disabled using the wireless
remote control method, the PIN code for the PIN code smart entry cannot
be cleared. ( P.114)
●In the following cases, perform the
PIN code registration procedure
again. • If the PIN code has been forgotten.
• When you wish to change the PIN
code.
●Make sure to change the PIN code
periodically.
●If the vehicle has been loaned to
another person, make sure that the PIN code has not been changed or
cleared. If the PIN code has been
changed or cleared, perform PIN code registration again.
■Unlocking method
●If an electronic key is within a detec-tion area, operation of the smart entry
will be given priority.
●If a mistake is made while entering the
PIN code, wait 5 seconds or more
before performing the procedure again.
●If the incorrect PIN code is entered 5 times consecutively, a buzzer will
sound for approximately 2 seconds
and operation will not be possible for 5 minutes.

127
3
3-5. Opening, closing the windows
Before driving
Press the switch down to lock the
passenger window glasses.
Use this switch to prevent children from
accidentally opening or closing a pas-
senger window.
WA R N I N G
Observe the following precautions.
Failure to do so may result in death or
serious injury.
■Closing the windows
●The driver is responsible for all the power window operations, including
the operation for the passengers. In
order to prevent accidental opera-
tion, especially by a child, do not let a child operate the power windows.
It is possible for children and other
passengers to have body parts caught in the power window. Also,
when riding with a child, it is recom-
mended to use the window lock switch. ( P.127)
●Check to make sure that all passen- gers do not have any part of their
body in a position where it could be
caught when a window is being operated.
●When using the wireless remote control or mechanical key and oper-
ating the power windows, operate
the power window after checking to make sure that there is no possibil-
ity of any passenger having any of
their body parts caught in the win- dow. Also do not let a child operate
window by the wireless remote con-
trol or mechanical key. It is possible for children and other passengers
to get caught in the power window.
●When exiting the vehicle, turn the engine switch off, carry the key and
exit the vehicle along with the child.
There may be accidental opera- tion, due to mischief, etc., that may
possibly lead to an accident.
■Jam protection function
●Never use any part of your body to
intentionally activate the jam pro- tection function.
●The jam protection function may not work if something gets jammed just
before the window is fully closed.
Be careful not to get any part of your body jammed in the window.
■Catch protection function
●Never use any part of your body or
clothing to intentionally activate the
catch protection function.
●The catch protection function may
not work if something gets caught just before the window is fully
opened. Be careful not to get any
part of your body or clothing caught in the window.
Preventing accidental opera-
tion (window lock switch)

1544-3. Operating the lights and wipers
To turn the lights on again, turn the
engine switch to ON, or turn the light
switch off once and then back to or
.
■Light reminder buzzer
A buzzer sounds when the engine switch is turned off and the driver’s door
is opened while the lights are turned on.
■Automatic headlight leveling sys-
tem
The level of the headlights is automati-
cally adjusted according to the number
of passengers and the loading condition of the vehicle to ensure that the head-
lights do not interfere with other road
users.
■Windshield wiper linked headlight illumination
When driving during daytime with the
headlight switch turned to , if the
windshield wipers are used, the head-
lights will turn on automatically after sev-
eral seconds to help enhance the visibility of your vehicle.
■Battery-saving function
In order to prevent the battery of the
vehicle from discharging, if the light
switch is in the or position when
the engine switch is turned off the bat-
tery saving function will operate and
automatically turn off all the lights after approximately 20 minutes.
When any of the following are per-
formed, the battery-saving function will be disabled.
●When the engine switch is turned to ACC or ON
●When the headlight switch is in the
position
●When a door is opened or closed
■Welcome light illumination control
The headlights and tail lights automati- cally turn on at night when the doors are
unlocked using the wireless remote con-
trol if the light switch is in the posi-
tion. The headlights and tail lights will turn off automatically after approxi-
mately 30 seconds.
■Customization
Some functions can be customized. ( P.377)
1With the headlights on, push the
lever away from you to turn on
the high beams.
Vehicles without high beam assist: If
the lever is pushed and released, the
high beam headlights will turn on. Pull
and release the lever to turn off the high
beam headlights and turn on the low
beam headlights.
Vehicles with high beam assist: If the
lever is pushed and released with the
headlight switch in position, the
high beam assist will turn on. When the
high beam assist is operating, the
headlights will automatically change
NOTICE
■To prevent battery discharge
Do not leave the lights on longer than
necessary when the engine is not run- ning.
Turning on the high beam
headlights

155
4
4-3. Operating the lights and wipers
Driving
between the high beams and low
beams according to the conditions. If
the lever is pushed forward and
released again, the high beam assist
will turn off and the high beam head-
lights will turn on.
To manually turn the high beam head-
lights on, push and release the lever
with the headlight switch in posi-
tion. If the lever is pulled and released,
the high beam headlights will turn off
and the low beam headlights will turn
on.
2 Illuminate the high beam head-
lights while the lever is pulled
Even if the lights are off, the high beam
headlights will illuminate. When the
lever is released, the headlights will
return to the low beam headlights or will
turn off.
This system allows the headlights
to be turned on for approximately
30 seconds when the engine switch
is off.
Pull the lever toward you and
release it with the light switch in
or after turning the engine
switch off.
The lights are turned off in the fol-
lowing situations:
 The engine switch is turned to
ON.
 The light switch is turned on.
 The light switch is pulled toward
you and then released.
 The doors are unlocked using
the smart entry & start system or
wireless remote control.
■Customization
Some functions can be customized. ( P.377)
*: If equipped
The SRH (Steering Responsive
Headlights) is a function which,
according to the steering wheel
operation and vehicle speed when
the vehicle is being driven forward,
automatically adjusts the angle of
the headlights to illuminate inter-
sections and corners, improving
visibility.
This function operates when the vehicle
speed is 8 km/h or higher.
Extended Headlight Lighting
system
SRH (Steering Responsive
Headlights)*

163
4
4-4. Refueling
Driving
1 With the doors unlocked, press
the center of the rear edge of
the fuel filler door.
Push until you hear a click and take your hand away to slightly open the fuel
filler door. Then open the door fully by
hand.
2 Turn the fuel tank cap slowly
and remove it, then put it into
the holder on the fuel filler door.
■When opening the fuel filler door
The fuel filler door cannot be opened if
the doors have been unlocked using a
inside lock button.
Unlock the doors using the entry func-
tion, wireless remote control, or door
lock switch. ( P.103, 105)
■If the fuel filler door cannot be opened
 P. 3 5 7
1After refueling, turn the fuel tank
cap until you hear a click. Once
WA R N I N G
●Turn the cap to the right until it
clicks to ensure that it is fully tight-
ened. If the cap is not securely tightened, fuel spillage could occur
in the event of an accident, creating
a fire hazard.
NOTICE
■Refueling
●Do not spill fuel during refueling.
Doing so may damage the vehicle,
such as causing the emission con- trol system to ope rate abnormally
or damaging fuel system compo-
nents or the vehicle’s painted sur- face.
●Never add any cleaning agents to the fuel tank. The addition of a
cleaning agent may cause damage
to the fuel system.
●Immediately put fuel in the tank
whenever the low fuel warning light
illuminates. Engine misfires as a result of an empty tank could cause
damage to the engine.
Opening the fuel tank cap
Closing the fuel tank cap

299
6
6-3. Do-it-yourself maintenance
Maintenance and care
“UPPER LEVEL” line
“LOWER LEVEL” line
If the fluid level is at or below the
“LOWER LEVEL” line, add distilled
water.
■Adding distilled water
1 Remove the vent plug.
2 Add distilled water.
If the “UPPER LEVEL” line cannot be seen, check the fluid level by looking
directly at the cell.
3 Put the vent plug back on and
close it securely.
■Before recharging
When recharging, the battery produces
hydrogen gas which is flammable and
explosive. Therefore, observe the fol- lowing before recharging:
●If recharging with the battery installed on the vehicle, be sure to disconnect
the ground cable.
●Make sure the power switch on the
charger is off when connecting and disconnecting the charger cables to
the battery.
■After recharging/reconnecting the
battery
The engine may not start. Follow the
procedure below to initialize the system.
1 Shift the shift lever to P (automatic
transmission) or depress the brake pedal with the shift lever in N (man-
ual transmission).
2 Open and close either door.
3 Restart the engine.
●Unlocking the doors using the smart
entry & start system may not be possi-
ble immediately after reconnecting the battery. If this happens, use the wire-
less remote control or the mechanical
key to lock/unlock the doors.
●Start the engine with the engine
switch in ACC. The engine may not start with the engine switch turned off.
However, the engine will operate nor-
mally from the second attempt.
●The engine switch mode is recorded
by the vehicle. If the battery is discon- nected and reconnected, the vehicle
will return the engine switch mode to
the status it was in before the battery was disconnected. Make sure to turn
off the engine before disconnecting
the battery. Take extra care when con- necting the battery if the engine switch
mode prior to the battery being dis-
connected is unknown.
If the engine will not start even after mul-
tiple attempts, contact any authorized Toyota dealer or repairer, or another
duly qualified and equipped profes-
sional.
A

3166-3. Do-it-yourself maintenance
up.
7 When installing, reverse the
steps listed.
■Checking interval
Inspect and replace the air conditioning
filter according to the maintenance schedule. In dusty areas or areas with
heavy traffic flow, early replacement
may be required. (For scheduled main- tenance information, please refer to the
“Toyota Service Booklet” or “Toyota War-
ranty Booklet”.)
■If air flow from the vents decreases dramatically
The filter may be clogged. Check the fil-
ter and replace if necessary.
■If the electronic key battery is
depleted
The following symptoms may occur:
●The smart entry & start system and wireless remote control will not func-
tion properly.
●The operational range will be reduced.
 Flathead screwdriver
 Lithium battery CR2032
■Use a CR2032 lithium battery
●Batteries can be purchased at any
authorized Toyota retailer or Toyota authorized repairer, or any reliable
repairer, local electrical appliance
shops or camera stores.
●Replace only with the same or equiva-
lent type recommended by the manu- facturer.
●Dispose of used batteries according to local laws.
NOTICE
■When removing the glove box
Do not forcibly pull the glove box.
Otherwise, the lower claws or the
lower claw engagement points may be deformed, making it difficult to
reinstall or close the glove box.
■When using the air conditioning
system
Make sure that a filter is always installed.
Using the air conditioning system
without a filter may cause damage to the system.
Electronic key batter y
Replace the battery with a new
one if it is depleted.
As the key may be damaged if
the following procedure is not
performed properly, it is rec-
ommended that key battery
replacement be performed by
any authorized Toyota retailer
or Toyota authorized repairer,
or any reliable repairer.
Items to prepare